低超声速圆球绕流后体流场的数值模拟

本文根据圆球跨声速自由飞行实验的流谱结构,建立了低超声速圆球分离流动的流动模型,它成功地计算了考虑粘性分离影响的圆球绕流的后体流场。在计算得到的后体流场中,反映流谱特征的分离激波、尾激波、分离界面等,其位置和形状与实验结果吻合很好,因此本文给出了一种能反映真实流动情况的圆球后体流场介。     

Two-phase flow patterns and void fractions in downward flow Part I: Steady-state flow patterns

Observations of void fractions and flow patterns have been made during steady-state, co-current, downward flow of liquid refrigerant 113 and its vapor. The new data on flow pattern transitions, plus the available downward flow data in the literature, have been compared with available predictions. It was found that the flow pattern map previously developed for horizontal and upward flow can be extended to downward flow with only minor modifications. Part II of this paper will report on the void fraction measurements and the observations of flow pattern transitions during flow transients.     

Transient solution for flow of evaporating fluid in parallel pipes using analysis based on flow patterns

Flow with evaporation in parallel lines with common inlet and outlet headers may result in an uneven flow distribution among the parallel pipes. The prediction of the flow rate distribution in steady state as well as under transient conditions was based on simplified models. In this paper a more accurate time dependent model based on the temporal-local flow pattern in the pipe is presented. The pipe is subdivided into numerical sections and the calculation of the pressure drop in each cell is based on mechanistic models that are specific for the flow pattern in the cell.     

The flow pattern map of a two-phase non-Newtonian liquid–gas flow in the vertical pipe

A map for the determination of flow pattern for two-phase flow of gas and non-Newtonian liquid in the vertical pipe has been presented. Our own experimental data confirm applicability of such a map.     

Flow pattern characterization for R-245fa in minichannels: Optical measurement technique and experimental results

An optical measurement method using image processing for two-phase flow pattern characterization in minichannel is developed. The bubble frequency, the percentage of small bubbles as well as their velocity are measured. A high-speed high-definition video camera is used to measure these parameters and to identify the flow regimes and their transitions. The tests are performed in a 3.0 mm glass channel using saturated R-245fa at 60 °C (4.6 bar). The mass velocity is ranging from 100 to 1500 kg/m² s, the heat flux is varying from 10 to 90 kW/m² and the inlet vapor quality from 0 to 1. Four flow patterns (bubbly flow, bubbly–slug flow, slug flow and annular flow) are recognized. The comparison between the present experimental intermittent/annular transition lines and five transition lines from macroscale and microscale flow pattern maps available in the literature is presented. Finally, the influence of the flow pattern on the heat transfer coefficient is highlighted.     

Flow pattern,void fraction and pressure drop of refrigerant two-phase flow in a horizontal pipe—I. Experimental data

Experiments with refrigerant two-phase flow in a horizontal pipe have been performed and data on flow pattern, void fraction and pressure drop have been obtained. Refrigerants used were R12 and R22, and the range of saturation pressure was from 5.7 to 19.6 bar.In this paper, the experimental equipment and procedure are described in detail, and the data are both tabulated and presented graphically.     

Periodic Stream Lines in the Three-Dimensional Square Cell Pattern

ＩｎｔｒｏｄｕｃｔｉｏｎＩｎｔｈｅｔｈｅｏｒｙｏｆｔｈｅｒｍａｌｃｏｎｖｅｃｔｉｏｎｉｎｓｔａｂｉｌｉｔｙｂｅｔｗｅｅｎｔｗｏｈｏｒｉｚｏｎｔａｌｐｌａｎｅ ,ｍａｎｙｐｌａｎｆｏｒｍｓｔｕｄｉｅｓｏｆＲａｙｌｅｉｇｈ＿Ｂｅｎａｒｄｃｏｎｖｅｃｔｉｏｎｈａｖｅｂｅｅｎｐｕｂｌｉｓｈｅｄｏｖｅｒｔｈｅｐａｓｔ 3 0ｙｅａｒｓ.Ｄ .Ｒ .Ｊｅｒｋｉｎｓ[1]ｓａｉｄ :“Ｏｎｔｈｅｔｈｅｏｒｅｔｉｃａｌｓｉｄｅ,ｉｎｔｅｒｅｓｔｈａｓｂｅｅｎｉｎｔｈｅｃｏｍｐｅｔｉｔｉｏｎｂｅｔｗｅｅｎｔｈｅｒｏｌｌ,ｓｑｕａｒ…     

New tracking algorithm for particle image velocimetry

The cross correlation tracking technique is widely used to analyze image data, in Particle Image Velocimetry (PIV). The technique assumes that the fluid motion, within small regions of the flow field, is parallel over short time intervals. However, actual flow fields may have some distorted motion, such as rotation, shear and expansion. Therefore, if the distortion of the flow field is not negligible, the fluid motion can not be tracked well using the cross correlation technique. In this study, a new algorithm for particle tracking, called the Spring Model technique, has been proposed. The algorithm can be applied to flow fields which exhibit characteristics such as rotation, shear and expansion.The algorithm is based on pattern matching of particle clusters between the first and second image. A particle cluster is composed of particles which are assumed to be connected by invisible elastic springs. Depending on the deformation of the cluster pattern (i.e., the particle positions), the invisible springs have some forces. The smallest force pattern in the second image is the most probable pattern match to the correspondent original pattern in the first image. Therefore, by finding the best matches, particle movements can be tracked between the two images. Three-dimensional flow fields can also be reconstructed with this technique.The effectiveness of the Spring Model technique was verified with synthetic data from both a two-dimensional flow and three-dimensional flow. It showed a high degree of accuracy, even for the three-dimensional calculation. The experimental data from a vortex flow field in a cylinder wake was also measured by the Spring model technique.     

任意形冒落非均质采空区流场流态数值模拟

为研究冒落非均质采空区流场流态及其随边界条件的变化，基于多孔介质渗流方程建立了采空区漏风流态的有限元数值模型，结合现场实例，从宏观上描绘了复杂几何形状采空区的漏风流态（风压分布等值线和流函数线），给出更准确的流态图形分布解．指出用流函数Laplace方程修正函数，对复杂形状和沿多边界方向非均质的采空区流场计算，仍能满足流网正交，其正交性可通过剖分网格精度来控制，得到采空区漏风强度沿固壁边界附近的冒落非压实区相对较大，工作面上下端附近处的漏风强度很大，并直通采空区深部。     

Visual observations of the flow around a half-submerged oscillating circular cylinder

Visual observations are made on the flow around a horizontal circular cylinder which is half-submerged in still water and forced to oscillate vertically. The ends of the cylinder have great influence on the wave pattern and flow field. Progressive plane waves are generated at small forcing amplitudes, but cross-waves are superimposed on the progressive plane waves at large forcing amplitudes. The wavelength of the cross-waves in the direction parallel to the cylinder axis increases with the forcing amplitude. The crests of the cross-waves are in parallel lines which are oblique to the cylinder axis. The angle at which the parallel lines meet the cylinder axis decreases as the forcing amplitude is increased. Three kinds of steady flows are induced in the water: surface flow, undersurface flow, and vertical jet.     

A flow pattern map for gas—liquid flow in horizontal pipes

Various flow pattern maps for two-phase gas—liquid flow in horizontal pipes are tested against the 5935 flow pattern observations presently contained in the UC Multiphase Pipe Flow Data Bank.A new flow regime correlation representing an extension of the work done by Govier and Aziz [3] is presented and is shown to be in better agreement with the data than the other correlations tested. A computer program for this correlation is included.It is also shown that there is no significant improvement obtained by including the effects of the physical properties of the fluids using any of the physical property parameters which have been proposed so far.     

Flow patterns in vertical two-phase flow

This paper is concerned with the flow patterns which occur in upwards gas-liquid two-phase flow in vertical tubes. The basic flow patterns are described and the use of flow pattern maps is discussed. The transition between plug flow and churn flow is modelled under the assumption that flooding of the falling liquid film limits the stability of plug flow. The resulting equation is combined with other flow pattern transition equations to produce theoretical flow pattern maps, which are then tested against experimental flow pattern data. Encouraging agreement is obtained.     

Liquid crystal techniques of visualization in rotating annulus experiments

To the well-known rotating annulus experiments we applied liquid crystal techniques of visualization in order to obtain clear video-pictures of internal flow and temperature in the fluid. Then we developed the idea of simultaneously injecting several types of liquid crystals of different temperature ranges to observe the fluid with a wide temperature range. It was shown that with this idea it was possible to take clear video-pictures throughout the whole interior of the fluid. This revealed that the pattern of the bottom flow does not have the characteristics of the Eady type baroclinic waves. Furthermore, the typcial meridional gradient of temperature of the baroclinic wave was directly observed from isothermal lines appearing in the fluid as colour band lines.     

Topological analysis of plasma flow control on corner separation in a highly loaded compressor cascade

In this paper, flow behavior and topology structure in a highly loaded compressor cascade with and without plasma aerodynamic actuation (PAA) are investigated. Streamline pattern, total pressure loss coefficient, outlet flow angle and topological analysis are considered to study the effect and mechanism of the plasma flow control on corner separation. Results presented include the boundary layer flow behavior, effects of three types of PAA on separated flows and performance parameters, topology structures and sequences of singular points with and without PAA. Two separation lines, reversed flow and backflow exist on the suction surface. The cross flow on the endwall is an important element for the corner separation. PAA can reduce the underturning and overturning as well as the total pressure loss, leading to an overall increase of flow turning and enhancement of aerodynamic performance. PAA can change the topology structure, sequences of singular points and their corresponding separation lines. Types II and III PAA are much more efficient in controlling corner separation and enhancing aerodynamic performances than type I.     

An application of the wavelet analysis technique for the objective discrimination of two-phase flow patterns

This paper presents an application of the wavelet analysis technique for two-phase flow pattern identification by using the void fraction signals obtained from a multi-channel Impedance Void Meter (IVM) in a vertical-upward air–water flow. A new method for the objective discrimination of the two-phase flow pattern has been developed to provide information regarding the local energy of void fraction signals at a given scale on the joint time–frequency diagram. The void signals are processed with Continuous Wavelet Transform (CWT) to get the local wavelet energy coefficients map on the time–frequency diagram. The effective local wavelet energy and the effective scale are then calculated. Then the criteria for flow pattern identification are, finally, obtained. A series of void fraction measurements were conducted over a wide range of air–water vertical-upward flow condition to provide an extensive database to cover several types of flow patterns. The results show that the proposed method has a high precision for characterizing different flow regimes in two-phase flow, and is considerably more promising for the online recognition of two-phase flow patterns due to the short time of data processing.     

Effects of fluid properties and pipe diameter on two-phase flow patterns in horizontal lines

Extensive new data have been obtained on the transitions between two-phase flow patterns during co-current gas liquid flow in horizontal lines. Fluid properties were varied in a systematic manner to determine the effects of liquid viscosity, liquid density, interfacial tension and gas density. Line sizes varied from 1.2 to 5 cm for most of the tests. Visual observations were supplemented by an analysis of pressure drop fluctuations and hence the present data are believed to be less subjective than most past observations.

The transition data from the present tests, as well as available literature data, were compared to the most frequently used transition line correlations. In almost all cases serious deficiencies were observed. Revised dimensionless correlations which fit present data, and those previously available, are presented.     

Slow Motion of a Porous Cylindrical Shell in a concentric cylindrical cavity

This paper concerns the Slow Motion of a Porous Cylindrical Shell in a concentric cylindrical cavity using particle-in-cell method. The Brinkman’s equation in the porous region and the Stokes equation for clear fluid in their stream function formulations are used. The hydrodynamic drag force acting on each porous cylindrical particle in a cell and permeability of membrane built up by cylindrical particles with a porous shell are evaluated. Four known boundary conditions on the hypothetical surface are considered and compared: Happel’s, Kuwabara’s, Kvashnin’s and Cunningham’s (Mehta-Morse’s condition). Some previous results for hydrodynamic drag force and dimensionless hydrodynamic permeability have been verified. Variation of the drag coefficient and dimensionless hydrodynamic permeability with permeability parameter σ, particle volume fraction γ has been studied and some new results are reported. The flow patterns through the regions have been analyzed by stream lines. Effect of particle volume fraction γ and permeability parameter σ on flow pattern is also discussed. In our opinion, these results will have significant contributions in studying, Stokes flow through cylindrical swarms.     

Structures in gas–liquid churn flow in a large diameter vertical pipe

Gas–Liquid two phase co-current flow in a vertical riser with an internal diameter of 127 mm was investigated in the churn flow pattern. This paper presents detailed experimental data obtained using a Wire Mesh Sensor. It shows that the most obvious features of the flow are huge waves travelling on the liquid film. Wisps, large tendrils of liquid and the product of incomplete atomisation, which had previously detected in smaller diameter pipes, have also been found in the larger diameter pipe employed here. The output of the Wire Mesh Sensor has been used to determine the overall void fraction. When examined within a drift flux framework, it shows a distribution coefficient of ∼1, in contrast to data for lower gas flow rates. Film thickness time series extracted from the Wire Mesh Sensor output have been examined and the trends of mean film thickness, that of the base film and the wave peaks are presented and discussed. The occurrence of wisps and their frequencies have been quantified.     

Visual observation of two-phase flow pattern of R-22, R-134a, and R-407C in a 6.5-mm smooth tube

Two-phase flow pattern and friction characteristics for R-22, R-134a, and R-407C inside a 6.5 mm smooth tube are reported in this study. The range of mass flux is between 50 and 700 kg/(m² s). The experimental data show that the two-phase friction multipliers are strongly related to the flow pattern. For a stratified, wavy flow pattern a mass-flux dependence of the multipliers is seen. The flow pattern transition for the mixture refrigerant shows a considerable delay, compared with that of pure refrigerant.     

On a family of Stokes flows

A family of simple Stokes flows involving sliding surfaces adjacent to surfaces at rest is considered. Principally, two specific flow configurations are investigated: (i) that arising when parts of the boundary of an infinitely long circular cylinder are rotating about the axis while other parts of the boundary are at rest, and (ii) the flow produced when a cap of a sphere is held at rest while the remainder of the sphere rotates about the symmetry axis. In each case computer plots of streamlines or constant velocity lines are presented to give a general impression of the resulting flow pattern.