High-density amine-terminated monolayers formed on fluorinated CVD-grown graphene

There has been considerable interest in chemically functionalizing graphene films to control their electronic properties, to enhance their binding to other molecules for sensing, and to strengthen their interfaces with matrices in a composite material. Most reports to date have largely focused on noncovalent methods or the use of graphene oxide. Here, we present a method to activate CVD-grown graphene sheets using fluorination followed by reaction with ethylenediamine (EDA) to form covalent bonds. Reacted graphene was characterized via X-ray photoelectron spectroscopy (XPS), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), and Raman spectroscopy as well as measurements of electrical properties. The functionalization results in stable, densely packed layers, and the unbound amine of EDA was shown to be active toward subsequent chemical reactions.     

Electrochemical characteristics of thin nickel hexacyanoferrate films formed on gold and thiol self-assembled monolayers modified gold electrodes.

Nickel hexacyanoferrate (NiHCF) film was prepared and characterized on gold and thiol self-assembled monolayers (SAMs)-modified gold electrodes. It was found that the film exhibited some different electrochemical characteristics compared with that found on a carbon electrode. In the presence of K+, the film exhibited a redox peak at about 0.5 V. The peak potential shifted linearly with the K+ concentration over the range of about 0.1 mM - 0.1 M with slopes of 54 - 60 mV per log[K+]. However, in solutions containing Na+, Li+ or NH4+ ion the film did not generate well-defined peaks, or even a visible redox peak. Therefore, the film showed a selective potential response to K+. The voltammetric behavior of NiHCF film varied with thiols, the preparation procedure and the solution pH. Under certain conditions, the characteristics of the film could be improved to some extent.     

Adsorption of CETP on monolayers formed from HDL extracted lipids

To obtain information on the interactions between CETP and HDL3 lipoproteins, we have studied (by surface tension measurements) the adsorption of the CETP at the air–water interface and at the interface between the water and monolayers formed by spreading of lipids extracted from HDL3. We have compared the interfacial behavior of CETP and ApoA-1 (the constitutive protein of HDL3); and the influence of monolayers composition and pressure on the kinetics of the CETP adsorption. The results obtained show that CETP was more expanded than the ApoA-1 which adsorbed more strongly at the air–water interface. CETP adsorbs more and quickly at the lipid interface that at the air–interface, specially for 20% fraction of cholesterol in the monolayer. Our results show that the adsorption of the CETP at the HDL3 surface lipids are strongly dependent of the composition of the monolayer and that the exclusion pressure of CETP varied from 31 to 33.7 mN m⁻¹ with the addition of cholesterol. Finally, the kinetics of the adsorption at water–lipid interface exhibited two steps (quick increase followed by slow decrease of the excess surface pressure) which should indicate a penetration into monolayer followed by a partial desorption of phospholipids with or without cholesterol corresponding to a proteolipid association.     

Structural characterization of organic multilayers on silicon(111) formed by immobilization of molecular films on functionalized Si-C linked monolayers

Silicon(111)-H surfaces were derivatized with omega-functionalized alkenes in UV-mediated and thermal hydrosilylation reactions to give Si-C linked monolayers. Additional molecular layers of organic compounds were coupled either directly or via linker molecules to the functionalized alkyl monolayers. In the first instance, amino-terminated monolayers were prepared from a tert-butoxycarbonyl-protected omega-aminoalkene followed by removal of the protecting group. Various thiols were coupled to the monolayer using a heterobifunctional linker, which introduced maleimide groups onto the surface. In the second system, N-hydroxysuccinimide (NHS) ester-terminated monolayers were formed by reaction of Si-H with N-succinimidyl undecenoate. The reactivity of the NHS ester groups was confirmed by further modification of the monolayer. The stepwise assembly of these multilayer structures was characterized by X-ray reflectometry and X-ray photoelectron spectroscopy.     

ALD resist formed by vapor-deposited self-assembled monolayers

A new process of applying molecular resists to block HfO2 and Pt atomic layer deposition has been investigated. Monolayer films are formed from octadecyltrichlorosilane (ODTS) or tridecafluoro-1,1,2,2-tetrahydrooctyltrichlorosilane (FOTS) and water vapor on native silicon oxide surfaces and from 1-octadecene on hydrogen-passivated silicon surfaces through a low-pressure chemical vapor deposition process. X-ray photoelectron spectroscopy data indicates that surfaces blocked by these monolayer resists can prevent atomic layer deposition of both HfO2 and Pt successfully. Time-dependent studies show that the ODTS monolayers continue to improve in blocking ability for as long as 48 h of formation time, and infrared spectroscopy measurements confirm an evolution of packing order over these time scales.     

Structure of spin-coated lipid films and domain formation in supported membranes formed by hydration

An atomic force and fluorescence microscopy investigation of the structure of spin-coated lipid films is presented. In the surface of the dry film, lipids are found to orient in a conformation where acyl chains are pointing outward while laterally the individual layers of the multilamellar film exhibit a dewetting pattern similar to what is found in polymer thin films. Hydration of the film in liquid water promotes detachment of bilayers from the surface while a single membrane remains on the mica substrate. This supported membrane is highly uniform and defect-free as compared to supported membranes prepared by conventional methods. It is further demonstrated that supported membranes of binary lipid mixtures prepared by this method exhibit gel-fluid domain coexistence in accordance with expectations from the phase diagrams.     

Density dependent friction of lipid monolayers

We measure frictional properties of liquid-expanded and liquid-condensed phases of lipid Langmuir-Blodgett monolayers by interfacial force microscopy. We find that over a reasonably broad surface-density range, the friction shear strength of the lipid monolayer film is proportional to the surface area (42-74 A2/molecule) occupied by each molecule. The increase in frictional force (i.e., friction shear strength with molecular area can be attributed to the increased conformational freedom and the resulting increase in the number of available modes for energy dissipation.     

The structure of percolating lipid monolayers

The lattice structure and in plane molecular organization of Langmuir monolayer of amphiphilic material is usually determined from grazing incidence X-ray diffraction (GIXD) or neutron reflectivity. Here we present results of a different approach for determination of monolayer lattice structure based on application of fractal analysis and percolation theory in combination with Brewster angle microscopy. The considerations of compressibility modulus and fractal dimension dynamics provide information on percolation threshold and consequently by application of percolation theory on the lattice structure of a monolayer. We have applied this approach to determine the monolayer lattice structures of single chain and double chain lipids. The compressibility moduli were determined from measured π-A isotherms and fractal dimensions from corresponding BAM images. The monolayer lattice structures of stearic acid, 1-hexadecanol, DPPC and DPPA, obtained in this way conform to the corresponding lattice structures determined previously by other authors using GIXD.     

Formation of dimers in lipid monolayers

In this work, we analyse theoretically the hypothesis that zwitterionic lipids form dimers in adsorption monolayers on water/ hydrocarbon phase boundary. A dimer can be modelled as a couple of lipid molecules whose headgroup lateral dipole moments have antiparallel orientation. Properties including surface pressure, chemical potentials and activity coefficients are deduced from a general expression for the free energy of the monolayer. The theoretical model is in a good agreement with experimental data for surface pressure and surface potential of lipid monolayers. The results favour the hypothesis about formation of dimers in equilibrium with monomers, with the amount of the species depending on the area per molecule and temperature. The reaction of dimerisation turns out to be exothermic with a heat of about 2.5kT per dimer. The results may be applied to the molecular models of membrane structures and mechanisms.     

Polyoxometalate monolayers in Langmuir-Blodgett films

Langmuir and Langmuir-Blodgett (LB) films of a variety of polyoxometalates of different shapes, sizes, and charges were prepared by taking advantage of the adsorption properties of these polyanions on a positively charged monolayer of an organic surfactant spread on water. Three different aspects were investigated. 1) The electrochemical and electrochromic properties of LB films containing the easily reducible polyoxoanion [P2Mo18O62]6-. Absorbance changes of these LB films deposited onto an ITO substrate have been induced by repeated switching of the applied potential. These changes are due to the formation of the colored reduced forms of the polyanion. Coloration and bleaching of the LB film occur very quickly and are reversible. 2) The preparation of LB films based on magnetic polyoxometalates, such as the Keggin anions, [CoW12O40]6- and [SiMn(OH2)W11O39]6-, or containing magnetic clusters of increasing nuclearities such as [Co4(H2O)2(PW9O34)2]10- and [Co4(H2O)2(P2W15O62)2]16- based on a Co4O16 ferromagnetic cluster, and the polyoxometalates [Co9(OH)3(H2O)6(HPO4)2(PW9O34)3]16- and [Ni9(OH)3-(H2O)6(HPO4)2(PW9O34)3]16- based on a nonanuclear M9O36 cluster. 3) The preparation of LB films of the giant heteropolyoxomolybdate, [Na3(NH4)12][Mo57Fe6(NO)6O174(OH)3-(H2O)24]76 H2O.     

Stability of self-assembled monolayers on titanium and gold

Methyl- and hydroxyl-terminated phosphonic acid self-assembled monolayers (SAMs) were coated on Ti from aqueous solution. Dodecyl phosphate and dodecyltrichlorosilane SAMs were also coated on Ti using solution-phase deposition. The stability of SAMs on Ti was investigated in Tris-buffered saline (TBS) at 37 degrees C using X-ray photoelectron spectroscopy, contact angle goniometry, and atomic force microscopy. For comparison purposes, a hydroxyl-terminated thiol SAM was coated on Au, and its stability was also investigated under similar conditions. In TBS, a significant proportion of phosphonic acid or phosphate molecules were desorbed from the Ti surface within 1 day, while the trichlorosilane SAM on Ti or thiol SAM on Au was stable for up to 7 days under similar conditions. The stability of hydroxyl-terminated phosphonic acid SAM coated Ti and thiol SAM coated Au was investigated in ambient air and ultraviolet (UV) light. In ambient air, the phosphonic acid SAM on Ti was stable for up to 14 days, while the thiol SAM on Au was not stable for 1 day. Under UV-radiation exposure, the alkyl chains of the phosphonic acid SAM were decomposed, leaving only the phosphonate groups on the Ti surface after 12 h. Under similar conditions, decomposition of alkyl chains of the thiol SAM was observed on the Au surface accompanied by oxidation of thiolates.     

Stability of monomolecular films of archaebacterial tetraether lipids on silicon wafers: a comparison of physisorbed and chemisorbed monolayers

The monomolecular organisation of symmetric, chemically modified tetraether lipids caldarchaeol-PO(4) was studied using Langmuir film balance, ellipsometry, and atomic force microscopy (AFM). Solid silicon wafer substrates were modified to hydrophobic, hydrophilic, and amino-silanised surfaces; and Langmuir-Blodgett (LB)-films were transferred onto each. LB-caldarchaeol-PO(4) films were subjected to further rinsing with organic solvent and additional physical treatments, to compare their resistance and stability on chemisorbed (amino-silanised) and physisorbed (hydrophobic and hydrophilic) surfaces. The resistance and stability of these monolayer films was characterized by ellipsometry and AFM, and film thickness was determined using ellipsometry. AFM was also employed to observe surface morphology. Monolayer films on hydrophobic surfaces were found to be more resistant to rinsing with organic solvent and additional physical treatments than monolayer films on either amino-silanised or hydrophilic surfaces. The hydrophobic effect with hydrophobic surfaces appears to support the formation of stronger caldarchaeol-PO(4) films on silicon wafer substrates, with increased resistance and stability.     

Supported bilayer lipid membrane arrays on photopatterned self-assembled monolayers

This work demonstrates the use of photocleavable cholesterol derivatives to create supported bilayer lipid membrane arrays on silica. The photocleavable cholesteryl tether is attached to the surface by using the reaction of an amine-functionalized self-assembled monolayer (SAM) and the N-hydroxysuccinimide-based reagent 9. The resultant SAM contains an ortho-nitrobenzyl residue that can be cleaved by photolysis by using soft (365 nm) UV light regenerating the original amine surface, and which can be patterned using a mask. The photoreaction yield was approximately 75 % which was significantly higher than previously found for related ortho-nitrobenzyl photochemistry on gold substrates. The SAMs were characterized by means of contact angle measurements, ellipsometry and X-ray photoelectron spectroscopy. Patterned surfaces were characterized with SEM and AFM. After immersing the patterned surface into a solution containing small unilamellar vesicles of egg phosphatidylcholine (PC), supported lipid membranes were formed comprised of lipid bilayer over the amine functionalized "hydrophilic" regions and lipid monolayer over the cholesteryl "hydrophobic" regions. This was confirmed by fluorescence microscopy and AFM. FRAP studies yielded a lateral diffusion coefficient for the probe molecule of 0.14+/-0.05 microm(2) s(-1) in the bilayer regions and approximately 0.01 microm(2) s(-1) in the monolayer regions. This order of magnitude difference in diffusion coefficients effectively serves to isolate the bilayer regions from one another, thus creating a bilayer array.     

Immobilization of acetylcholinesterase in lipid membranes deposited on self-assembled monolayers

Human red blood cell acetylcholinesterase was incorporated into planar lipid membranes deposited on alkanethiol self-assembled monolayers (SAMs) on gold substrates. Activity of the protein in the membrane was detected with a standard photometric assay and was determined to be similar to the protein in detergent solution or incorporated in lipid vesicles. Monolayer and bilayer lipid membranes were generated by fusing liposomes to hydrophobic and hydrophilic SAMs, respectively. Liposomes were formed by the injection method using the lipid dimyristoylphosphatidylcholine (DMPC). The formation of alkanethiol SAMs and lipid monolayers on SAMs was confirmed by sessile drop goniometry, ellipsometry, and electrochemical impedance spectroscopy. In this work, we report acetylcholinesterase immobilization in lipid membranes deposited on SAMs formed on the gold surface and compare its activity to enzyme in solution.