The adsorption of tetraethylammonium ions at a mercury electrode from perchlorate solutions

The adsorption of tetraethylammonium ions at the mercury-perchlorate solution interphase has been studied. Solutions at constant perchloric acid activity have been prepared and the use of several perchloric acid activities allows us to calculate the simultaneous adsorption of both ions: tetraethylammonium and perchlorate. An interphase model is described to explain co-adsorption of both ions.     

Electrochemical impedance study of hydrogen evolution on Bi(001) electrode in the HClO4 aqueous solutions

Electrochemical impedance spectroscopy has been applied for investigation of the hydrogen evolution kinetics at the electrochemically polished Bi(001) plane, and the complicated reaction mechanism (slow adsorption and charge-transfer steps) has been established. The charge-transfer resistance and adsorption capacitance values depend noticeably on the electrode potential applied. The adsorption resistance is maximal in the region of electrode potential E _min = −0.65 V vs. (Hg|Hg₂Cl₂|4 M KCl), where the minimal values of constant phase element (CPE) coefficient Q have been calculated. The fractional exponent α _CPE values of the CPE close to unity (α _CPE ≥ 0.94 and weakly dependent on the electrode potential and pH of solution () have been obtained, indicating the weak deviation of Bi(001)|HClO₄ + H₂O interface from the ideally flat capacitive electrode. Q differs only very slightly from double-layer capacitance C _dl values in the whole region of potentials and , investigated.     

Study of adsorption from solutions by frontal chromatography

Summary The automatic frontal chromatography installation was described. By this chromatographic method the adsorption isotherm of benzene from n-heptane solutions on hydroxylated surface of silica with various porosity has been determined. This investigation was performed at different flow rates of eluent and in a wide range of concentrations. The isotherm of adsorption obtained by this chromatographic method has been compared with the results of the static measurements. The coincidence of adsorption isotherms measured at the various flow rates are shown to be a criterion of proximity the chromatographic process to the equilibrium.     

Removal of copper from aqueous solutions by adsorption on activated carbons

The adsorption isotherms of Cu(II) ions from aqueous solutions in the concentration range 40–1000 mg l⁻¹ on two samples of granulated and two samples of activated carbon fibres containing varying amounts of associated oxygen have been reported. The adsorption isotherms are type I of BET classification showing initially a rapid adsorption tending to be asymptotic at higher concentrations. The amounts of oxygen associated with the carbon surface has been enhanced by oxidation with nitric acid and ammonium persulphate in the solution phase and with oxygen gas at 350°C and decreased by degassing of the oxidized carbon samples at 400, 650 and 950°C. The adsorption of Cu(II) ions increases on oxidation and decreases on degassing. The increase in adsorption on oxidation depends on the nature of the oxidative treatment while the decrease in adsorption on degassing depends on the temperature of degassing. This has been attributed to the increase in the carbon–oxygen acidic surface groups on oxidation and their decrease on degassing. Suitable mechanisms consistent with the results have been proposed.     

Study on the adsorption and aggregation of dilute gemini surfactant solutions

As a function of temperature in aqueous solutions, the adsorption and aggregation of N,N’-bis (tetradecyl dimethyl)-1,2-dibromide-ethanediyl ammonium salt (GS14-2-14) and N,N’-bis (hexadecyl dimethyl)-1,2-dibromide-ethanediyl ammonium salt (GS16-2-16), were researched with drop-volume technique and conductometry, respectively. The results of surface tension measurements, which were analyzed by originally developed thermodynamic equations, illustrate that GS14-2-14 has a better surface activity and arranges more tightly in the adsorbed film than GS16-2-16. The data of conductivity were used to find critical micelle concentration (cmc) and counterion binding degree of micelle (β). Thermodynamic parameters of micellization were also obtained from the temperature dependence of cmc values. From the study, it is discovered that the micellization process is spontaneous and exothermic in nature and it is mainly driven by entropy.     

含氰基聚合物微球对铜离子吸附性能的研究

以火焰原子吸收光谱法(FAAS)为检测手段,研究了聚丙烯腈微球(PANMS)对溶液中Cu2+的吸附及其影响因素,并建立了PANMS分离富集-FAAS法。实验结果表明,溶液pH为5、静态吸附时间为1.5 h、温度为20℃时,其对Cu2+的吸附达到饱和而稳定,吸附容量为30.2 mg/g,吸附率可达到87.5%。随着吸附时间的延长吸附率有所提高,但幅度不是很大。以0.1 mol/LHC l溶液作为解吸剂,解吸率可达到96.5%。经富集50倍后,测Cu2+工作曲线的回归方程为A=0.0025C(μg/L)-0.0026(r=0.9993),方法的检出限为1.68μg/L,相对标准偏差(RSD)小于2.9%。加标回收率为91.4%~97.0%。     

Biosorption of copper ions from aqueous solutions by Spirulina platensis biomass

In this study, the economically important micro-alga (cyanobacterium) Spirulina platensis was used as biosorbent for the removal of copper from aqueous solutions. The cyanobacterium was exposed to various concentrations of copper and adsorption of copper by the biomass was evaluated under different conditions that included pH, contact time, temperature, concentration of adsorbate and the concentration of dry biomass. Increased adsorption of copper by the non-living biomass was recorded with gradually increasing pH, and a maximal uptake by the biomass was observed at pH 7. The adsorption of copper was found to increase gradually along with decrease in biomass concentration. Biosorption was found to be at a maximum (90.6%), in a solution containing 100 mg copper/L, at pH 7, with 0.050 g dry biomass and at 37 °C with 90 min of contact time. Analysis of the spectrum obtained with atomic absorption spectrophotometer (AAS), indicated that the adsorbent has a great potential to remove copper from aqueous media contributing to an eco-friendly technology for efficient bioremediation in the natural environment.     

Ultrasound-assisted adsorption of Pb ions by carbonized/activated date stones from singles/mixed aqueous solutions

This work aims to assess the adsorption efficiency of date stones biowaste subjected to carbonization and activation processes for the removal of Pb ions from single and mixed solutions. Several techniques have been used for characterization of adsorbents such as scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), methylene blue index and point of zero charge (pHpzc). An excellent adsorption capacity of 97.43% is achieved at an initial concentration of 300 ?mg/L, solution volume 75 ?mL of Pb nitrate, adsorbent mass of 0.7 ?g, temperature of 30 ?°C, a stirring speed of 500 ?rpm/min, a contact time of 180 ?min and pH 6. Specifically, a comparison has been conducted between carbonized/activated date stones “CADS” and commercial activated carbon “CAC” besides investigating the influence of the presence of Co ions and the utilization of ultrasound radiation. A higher adsorption rate of 98.16% is reached under ultrasound radiation at Pb(II) initial concentration of 100 ?mg/L for a contact time of 3 ?h. Nevertheless, the temperature has shown a negative effect; the adsorption rate decreases from 98.31% at 18 ?°C to 92.70% at 60 ?°C. The modeling of the experimental adsorption data manifests a type-L isotherm characteristic of Langmuir and Freundlich models. The kinetic study has shown that the experimental data are well described by a pseudo-second-order rate model and controlled by the internal diffusion, a limiting-step that controls the transfer rate of Pb(II) to the adsorbent surface. The calculated thermodynamic parameters (ΔG⁰, ΔH⁰, ΔS⁰) indicate that the adsorption of Pb(II) is spontaneous and exothermic process.     

Adsorption of metal ions from solution onto a piezoelectric quartz crystal

Many metal ions are spontaneously adsorbed onto a piezoelectric quartz crystal and change the oscillation frequency. The pH ranges in which the metal ions adsorbed were just below that of precipitate formation as the ‘hydroxides’; frequency changes caused by adsorption were not observed in these pH ranges where the ‘hydroxides’ formed. Cationic organic reagents, such as crystal violet and methylene blue, were also adsorbed on the piezoelectric quartz crystal but non-ionic and anionic organic compounds were not. These results showed that the crystal was negatively charged on the surface.     

The kinetics of ethanol adsorption from the aqueous phase onto zeolite NaZSM-5

The kinetics of the isothermal adsorption of ethanol from an aqueous solution onto a hydrophobic zeolite of the NaZSM-5 type in the temperature range 298–333 K was investigated. Specific shape parameters of the adsorption degree curves were determined. The changes in the specific shape parameters of the adsorption degree curves with temperature were determined. The kinetic parameters of ethanol adsorption (E_a,ln A) were determined by the initial rate, the saturation rate and the maximum rate methods as well as from the Johnson, Mehl and Avramy equation. The kinetic model of ethanol adsorption kt=[1−(1−α)^1/3] was determined by the “model fitting” method. Ethanol adsorption from aqueous solution onto NaZSM-5 is a kinetically controlled process limited by the rate of three-dimensional movement of the boundary layer of the adsorption phase. A model for the mechanism of ethanol adsorption onto NaZSM-5 is suggested on the basis of the kinetic model. Ethanol molecules in aqueous solution are associated in clusters. The activation energy of the adsorption process corresponds to the energy required for the detachment of an ethanol molecule from a cluster and its adsorption onto the zeolite.     

HPLC study of the adsorption from solutions on two silicagels

Summary In this paper, we report and discuss the adsorption isotherms of hydro-organic mixtures and of compounds used as mobile phase in reversed phase and normal phase high performance liquid chromatography (RP-HPLC and NP-HPLC, respectively). This work is the first attempt to study the solid-liquid interface between two types of chromatographic silica surfaces and pure organic adsorbates from water and from organic eluents by HPLC. Frequently, among the dynamic techniques the method of choice for the measurement of an adsorption isotherm is frontal analysis. We suggest here the combination of the technique based on peak asymmetry calibration and peak profiles, which allows calculations directly from integration data. The group of systems studied permits the analysis of the intermolecular interactions on the silica surface. Particular attention was given to the system methanol-water and the measurement of the adsorption ofn-octanol from methanol on RP-silica was also carried out.     

Chromatographic investigations of adsorption of some aromatic compounds on aluminium oxide and silica gel from solutions

Summary Using adsorption TLC R_M values were measured for a number of aromatic compounds on aluminium oxide and silica gels having different specific surface areas, using the following binary mobile phases: benzene+toluene, benzene+carbon tetrachloride and chloroform+carbon tetrachloride. The results are graphically presented and compared with theoretically calculated values. Generally, a good agreement was found between the calculated and measured R_M values. The agreement is valid both when the R_M values were calculated using experimentally (indirectly) determined partition coefficients or when the coefficients are obtained with help of Ocik's equation [cf. Roczn. Chem.34, 745 (1960) and Chromatographia4, 516 (1971)]. One can assume that in the case of systems in which strong intermolecular interactions are absent, the statically determined partition coefficients of the compounds may be used for the calculation of their R_M values.     

Method of the Green functions in the kinetics of adsorption from micellar surfactant solutions

The kinetics of adsorption from micellar surfactant solutions is considered theoretically from a uniform point of view. Three boundary value problems for the adsorption on flat and on spherical interface are solved analytically by means of the method of the Green functions. In this way the bulk concentration and the adsorption of surfactant monomers are expressed as functions of time. The contribution of the micelles (surfactant aggregates) to the diffusion of the monomers is accounted for as pseudo-first order reaction. The adsorption from surfactant solutions without micelles turns out to be the particular case of the problems considered here. Being general in form, the derived equations can be applied also to other practical problems in heterogeneous chemical kinetics, adsorption of gases, heat transfer, etc.     

A new isotherm equation for single-solute adsorption from dilute solutions on energetically heterogeneous solids

A new isotherm equation is proposed for describing single-solute adsorption from dilute solution on energetically heterogeneous solids. This equation comprises all isotherm equations being an extension of simpleLangmuir isotherm to single-solute adsorption on heterogeneous solids. The phenol adsorption data from dilute aqueous solutions on activated carbon are studied by using this new equation.

---

Eine neue Isothermengleichung für die Adsorption aus verdünnten Einzelkomponentenlösungen auf energetisch heterogenen Festkörpern (Kurze Mitteilung)

Zusammenfassung Es wurde eine neue Isothermengleichung für die Adsorption aus verdünnten Einzelkomponentenlösungen auf energetisch heterogenen Festkörpern vorgeschlagen. Diese Gleichung schließt alle bisherigen Isothermengleichungen in sich ein, die Verallgemeinerungen der einfachenLangmuir-Isotherme für Adsorption auf heterogenen Festkörpern sind. Es wurden Daten der Adsorption von Phenol aus verdünnten Wasserlösungen auf aktivierte Kohle unter Verwendung der neuen Gleichung untersucht.

     

Removal of Cu(II), Zn(II) and Co(II) ions from aqueous solutions by adsorption onto natural bentonite

In this study, the removal of Cu(II), Zn(II) and Co(II) ions from aqueous solutions using the adsorption process onto natural bentonite has been investigated as a function of initial metal concentration, pH and temperature. In order to find out the effect of temperature on adsorption, the experiments were conducted at 20, 50, 75 and 90 °C. For all the metal cations studied, the maximum adsorption was observed at 20 °C. The batch method has been employed using initial metal concentrations in solution ranging from 15 to 70 mg L⁻¹ at pH 3.0, 5.0, 7.0 and 9.0. A flame atomic absorption spectrometer was used for measuring the heavy metal concentrations before and after adsorption. The percentage adsorption and distribution coefficients (K _d) were determined for the adsorption system as a function of adsorbate concentration. In the ion exchange evaluation part of the study, it is determined that in every concentration range, adsorption ratios of bentonitic clay-heavy metal cations match to Langmuir, Freundlich and Dubinin-Kaganer-Radushkevich (DKR) adsorption isotherm data, adding to that every cation exchange capacity of metals has been calculated. It is shown that the bentonite is sensitive to pH changes, so that the amounts of heavy metal cations adsorbed increase as pH increase in adsorbent-adsorbate system. It is evident that the adsorption phenomena depend on the surface charge density of adsorbent and hydrated ion diameter depending upon the solution pH. According to the adsorption equilibrium studies, the selectivity order can be given as Zn²⁺>Cu²⁺>Co²⁺. These results show that bentonitic clay hold great potential to remove the relevant heavy metal cations from industrial wastewater. Also, from the results of the thermodynamic analysis, standard free energy ΔG ⁰, standard enthalpy ΔH ⁰ and standard entropy ΔS ⁰ of the adsorption process were calculated.     

Global non-ideality effects in adsorption of organic substances from dilute aqueous solutions on activated carbon

Summary A method for the quantitative estimation of the global non-ideality of the adsorption of weak organic electrolytes on activated carbon from dilute aqueous solutions is presented. The method is based on the analysis of aGraham plot which reflects the adsorption isotherm deviations from ideality. Averaging these deviations over the whole range of adsorption, one gets a single value representing the global non-ideality of a system. The method also allows to estimate the contributions of heterogeneity and interactions in the adsorbed phase to the global non-ideality effect. The theoretical considerations are illustrated by some model calculations. The usefulness of the method is tested for experimental data of benzoic and salicyclic acid adsorption over a wide range ofpH and concentrations.

---

Globaler Effekt der Nicht-Idealität bei der Adsorption organischer Substanzen aus verdünnten wässerigen Lösungen an Aktivkohle

Zusammenfassung Es wird eine Methode zur quantitativen Abschätzung der globalen Nicht-Idealität für die Adsorption schwacher organischer Elektrolyte aus verdünnten wässerigen Lösungen an Aktivkohle vorgestellt. Diese Methode basiert auf der Analyse der bekanntenGraham-Abhängigkeit, die die Abweichung der Adsorptionsisotherme von der Idealität zeigt. Bei Errechnung des Durchschnittwertes dieser Abweichung über den ganzen Asorptionsbereich erhält man einen Wert, der die globale Nicht-Idealität für ein Adsorptionssystem charakterisiert. Die Methode erlaubt auch, den Beitrag der Heterogenität und der Wechselwirkungen in der Adsorptionsphase zum globalen Effekt der Nicht-Idealität abzuschätzen. Die theoretischen Erörterungen werden an Hand von Modellberechnungen illustriert. Die Nutzbarkeit der Methode wurde mit experimentellen Daten der Benzoe- und Salicylsäureadsorption in einem weiten Bereich vonpH und Konzentration getestet.

     

Study of biocatalyst to produce ethanol from starch

This article presents a detailed study on the conditions for achieving a stable biocatalyst to be used in the production of ethanol from starch. Different pellets were used depending on which characteristic of the biocatalyst was being studied: (a) Saccharomyces cerevisiae entrapped in pectin or calcium alginate gel particles; (b) silica containing immobilized glucoamylase entrapped in pectin gel particles; or (c) pectin gel particles, with the silicaenzyme derivative and yeast coimmobilized. The influence of several variables on the mechanical resistance of the particle, on the viability of the microorganism, and on the rate of substrate hydrolysis was studied with biocatalyst. The best conditions found were 6% pectin gel, 2-mm particle diameter, and curein 0.2 M CaCl₂·2H₂O/60 mM acetate buffer, pH 4.2, for gel preparation; and 6.0 g/L of CaCl₂·2H₂O in the fermentation medium. Biocatalyst (c) was successfully tested for the production of ethanol from liquefield manioc flour syrup.     

Specific adsorption of azide ions on mercury electrodes from constant ionic strength solutions

The adsorption of azide ions on mercury from aqueous solutions of NaN₃+NaF at constant ionic strength has been studied by measurements of the double layer capacity. Taking into account changes in the structure of the diffuse layer, it was possible to show that the properties of the inner layer are similar to those observed previously in solutions of pure NaN₃, and that the same adsorption isotherm applies to both systems.