Effect of modification with rubber on properties and process of curing of epoxy–rubber adhesive compositions

The effect of SKN-30KTRA low molecular weight rubber on the elastic and strength properties of adhesive compositions made with epoxy-rubber composition, is shown. The data on the effect of rubber on curing of adhesive compositions are presented.     

Elastic and thermoelastic properties of “inorganic rubber”

Polymerization of cyclic phosphonitrilic chloride trimer was carried out at sufficiently high temperatures and for sufficiently long periods to cause gelation of the poly(dichlorophosphazene) formed. The resulting crosslinked material, called “inorganic rubber”, was found to be stable enough in the absence of moisture to permit reliable stress-strain and stress-temperature (thermoelastic) measurements in elongation. The stress-strain isotherms at low and moderate values of the elongation, α, showed that the networks had relatively low degrees of crosslinking; at high α and low temperature, they underwent strain-induced crystallization. The thermoelastic data confirmed the occurrence of crystallization at high α and low T. Thermoelastic values of the fraction f_e/f of the force that is of energetic origin were negative and generally large, with a magnitude that increased with increase in α, presumably because of the crystallization. In any case, the experimental values of f_e/f are in at least qualitative agreement with rotational isomeric state theory, which predicts this ratio to be large and negative.     

Quantitative characterization of toughening mechanisms of rubber modified polymers

The volume changes of rubber modified polymers under creep at room temperature were successfully used to characterize the toughening mechanisms of blends with brittle polymer matrices such as high impact polystyrene.This approach cannot be applied to pseudo-ductile polymers such as polypropylene and polyamide,because they are ductile when stretched at low speed at room temperature.Based on the time-temperature equivalence princi ple,the volume change at low temperature is proposed to characterize quantitatively the toughening mechanisms of polymer blends with ductile matrices,which is illustrated by applying this approach to rubber modified polypropylene     

Dielectric properties of perbunan rubber: γ-irradiation effects

A systematic dielectric study over a frequency range extending from 200 Hz to 100 kHz and temperature ranging from 20° to 60°C has been carried out on perbunan rubber. The acrylonitrile content of the rubber samples was 28% and 38%. The effect of 15 MR γ-irradiation on the dielectric properties of both samples was studied and the results are interpreted. The study revealed that NBR-38 is better than NBR-28 for insulating purposes.     

Thermal stability and flammability of butadiene–styrene rubber nanocomposites

Heterobimetallic oxalato complex precursors, manganese(II)tetraaquatris(oxalato)lanthanate(III)hexahydrate (MnOLa), cobalt(II)pentaaquatris(oxalato)lanthanate(III)trihydrate (CoOLa), nickel(II)pentaaquatris(oxalato)lanthanate(III)hexahydrate (NiOLa) and copper(II)diaaquatris(oxalato)lanthanate(III)monohydrate (CuOLa) of the type, M₃[La(C₂O₄)₃(H₂O) _m ]₂·nH₂O have been synthesized in aqueous medium. The precursors were characterized by elemental analysis, IR, electronic spectral and powder X-ray diffraction studies. The good crystalline nature with monoclinic structures predominates in MnOLa and NiOLa whereas triclinic structures were found in CoOLa and CuOLa. The solid-state thermal behaviour of the precursors was explored using TG, DTG and DTA in air. The MnOLa generated a mixture species consisting mainly of MnO₂, Mn₃O₄, Mn₅O₈, La₂O₃ and LaMn₇O₁₂ at 1000 °C through the formation of several intermediate species at 380 and 570 °C. The studies revealed that CoOLa led mainly to LaCoO₃ and La₂CoO₄ along with some oxides of both the cobalt and lanthanum at 1000 °C. In case of nickel analogue the mixture species identified at 1000 °C are mainly of La₂NiO₄, La₂O₃, Ni₂O₃ and NiO_2. In case of CuOLa the product at 1000 °C consisted of La₂CuO₄, La₂Cu₂O₅ and oxides of copper and lanthanum. The nature of decomposition of the precursors in nitrogen were seen from DSC study and the kinetic parameters i.e., E ^* , lnk ₀, ΔH ^# , ΔS ^# and order of reaction of all the steps were evaluated and discussed.     

Effect of sol–gel derived in situ silica on the morphology and mechanical behavior of natural rubber and acrylonitrile butadiene rubber blends

Silica particles were generated and grown in situ by sol–gel method into rubber blends comprised of natural rubber (NR) and acrylonitrile butadiene rubber (NBR) at various blend ratios. Silica formed into rubber matrix was amorphous in nature. Amount of in situ silica increased with increase in natural rubber proportion in the blends during the sol–gel process. Morphology studies showed that the generated in situ silica were nanoparticles of different shapes and sizes mostly grown into the NR phase of the blends. In situ silica filled NR/NBR blend composites showed improvement in the mechanical and dynamic mechanical behaviors in comparison to those of the unfilled and externally filled NR/NBR blend composites. For the NR/NBR blend at 40/60 composition, in particular, the improvement was appreciable where size and dispersion of the silica particles into the rubber matrix were found to be more uniform. Dynamic mechanical analysis revealed a strong rubber–in situ silica interaction as indicated by a positive shift of the glass transition temperature of both the rubber phases in the blends.     

In vitro drug release from silicone rubber–polyacrylamide composite

Composite materials containing drugs were prepared from silicone rubber and hydrogel. Cross linked polyacrylamide (PAAm) hydrogel particles were incorporated into a silicone rubber to enhance the hydrophilicity and drug release capacity of silicone rubber as a matrix. Progesterone and Thymol Blue were used as a hydrophobic and hydrophilic drug model, respectively. Different amounts of polyacrylamide (PAAm) were mixed with the drugs and uncured silicone rubber at room temperature. The composite matrices were formed using a compression molding press and cured by thermal and γ-irradiation curing methods. In vitro drug release behavior of composites and their physical and mechanical properties were investigated. The results indicated that the hydrophilic character of silicone rubber was more pronounced with increasing the amount of PAAm. Also, a significant effect on the drug release profiles was observed. The γ-irradiation curing method improved mechanical properties of composites and affected the drug release profiles. It was found that the amounts of released progesterone from γ-irradiated samples increased in comparison with the thermally cross linked composite since released Thymol Blue was reduced.     

Gamma-ray absorption using rubber—lead mixtures as radiation protection shields

In the present study five samples of special rubber–lead were fabricated each of them consists of lead and rubber with different weight ratios. The fabrication was carried out through the process of mixing under compression pressure. Gamma-ray transmission method was employed to determine the linear attenuation coefficient for narrow collimated mono-energetic beams of gamma-rays emitted from ²⁴¹Am 0.059, ¹⁵²Eu 0.13 and ¹³⁷Cs 0.662 MeV. The linear attenuation coefficient of standard rubber–lead shield was also experimentally determined. The percentage of lead in standard rubber–lead shield was determined through the calibration curve or by a simple computer program written in MATLAB. All prepared samples are characterized as flexible and gives a good homogeneity. samples no. 4 & 5 offers the best performance as a radiation protection shields. The results showed an inverse proportionality between the linear attenuation coefficient μ_{l and E}, and μ_l has a direct proportionality with mixing ratios (sample density). The results showed an inverse proportional between the half value layers and the average linear attenuation coefficients of the various samples.     

Composite natural rubber–polychloroprene latex particles produced by the heterocoagulation technique

Composite natural rubber (NR) based latex particles were prepared using the heterocoagulation technique. A nonionic surfactant (Tween 80) whose molecules bear poly(ethylene oxide) (PEO) was adsorbed on polychloroprene (CR) latex particles and allowed to form complexes between PEO and indigenous surfactant (protein–lipid) on the NR particle surface. The heterocoagulated NR/CR–Tween particles produced were characterised by particle size, zeta-potential and glass-transition temperature measurements and the data indicated the presence of CR–Tween on the outer layer of the composite polymer particles. The results agreed well with the better oil resistance of films cast from heterocoagulated latex when compared with that of the NR film. Received: 22 August 2000 Accepted: 8 January 2001     

Uptake of lead by carbonaceous adsorbents developed from tire rubber

The adsorption of lead in aqueous solution by discarded tire rubber (TR) and by carbonaceous adsorbents (CAs) prepared from it by thermal and chemical treatments is studied. TR was heated at 400 or 900?°C for 2 h in N₂ atmosphere or treated chemically with H₂SO₄, HNO₃, H₂SO₄/HNO₃, HCl, NaOH, HCl-NaOH or NaOH-HCl for 24 h. TR and CAs were characterized physico-chemically with regard to their texture, elemental composition and surface chemistry. The adsorption of lead was studied, mainly from the kinetic standpoint, using 4×10^?3 mol?L^?1 Pb²⁺ solutions at initial pH 2.0, 5.7 and 12.6. TR is practically a non-porous material. The heat treatment of TR mainly develops meso- and macroporosity. The effect on macroporosity is stronger when HNO₃ and H₂SO₄/HNO₃ are used. For all adsorbents, the adsorption of lead is not measurable when adsorptive solution at pH 2 is used. With an increase of pH from 5.7 to 12.6, the kinetics of adsorption becomes faster and the amount of lead adsorbed significantly increases. For the solution at pH 12.6 and an adsorption time of 8 h, the adsorption percentage is 36 wt% for TR. For the CAs prepared by heat treatment of TR, it is higher than 50 wt%. For longer adsorption times, the kinetics is much slower for the product of TR treatment with HNO_3. However, the corresponding adsorption percentage is as high as 93 wt% for an adsorption time of 264 h. TR and the CAs, in particular the product heated at 400?°C, are good adsorbents to be used in the rapid removal of a significant amount of lead from aqueous solution.     

Thermal stability and flammability of styrene–butadiene rubber (SBR) composites

The article presents the effect of attapulgite (ATT) and its synergic action with carbon or silica on the thermal properties and flammability of cross-linked styrene–butadiene rubber. It has been shown that ATT is active filler improving the thermal and mechanical properties of composites containing this aluminosilicate. The decreased flammability of vulcanizates containing ATT compared to that of unfilled vulcanizates results from good insulating properties of the ATT used. The considerable reduction in the flammability of composites containing ATT and carbon nanofiber or silica is connected, first of all, with the formation of a homogeneous boundary layer.     

Tensile property of cord reinforced rubber composites laminate double lap jointEI北大核心CSCD

According to the structural connection form of cord reinforced rubber composite，structural test samples with different lapping process parameters were designed and prepared. The dynamic and static tensile properties were studied by using two-dimensional digital image technology. The test results were as follows：The stiffness and tensile strength of double lap composites joints increased as the strain rate increasing，while the elongation at break unchanged. Compared with the no-lap samples，the tensile strength of the double lap composites sample was reduced by nearly 50%，and with the increase of the lap width，the elongation at break gradually decreased. The samples with lap width of 65 mm decreased by 24% compared with the no-lap ones. Compared with the elastic modulus of stage II，the elastic modulus of stage III increased significantly，that of the no-lap samples increased by 3 times，that of the lap samples were doubled，and the amplification of elastic modulus decreased with the increase of strain rate. © 2023, Youke Publishing Co.,Ltd. All rights reserved.     

Room-temperature vulcanized silicone rubber/barium titanate–based high-performance nanocomposite for energy harvesting

Rubber composites were prepared for elastomer slab by mixing barium titanate (BaTiO₃), carbon nanotube (CNT), carbon black (CB), and room-temperature vulcanized (RTV) silicone rubber. An electrode was prepared from composite for energy harvesting with fillers such as CB and CNT, and RTV thinner was used to improve the processing of the specimen. At 50 phr of BaTiO₃, there is an increase in compressive modulus by 180%. There was a correlation between prestrain and biaxial strain in enhancing the energy generation. After poling of the rubber composite containing 50 phr of BaTiO₃ at 11 kV/mm, the energy harvesting was increased at all strains. In durability test at 70 phr of BaTiO₃ for 60% cyclic biaxial strain, the drop in voltage from the piezoelectric energy harvesting was almost zero for 3000 cycles.     

Relation between stress relaxation and aging resistance of rubber vulcanizates—some preliminary investigations

In this paper some details are given for the construction of a simple balance for the measurement of stress relaxation at constant elongation. A simple means of obtaining equal strain in the two parts of the strained specimen is provided. By means of four typical stocks covering the widest possible range of aging resistance it is shown that the stress relaxations give approximately the same estimate of stability as does the normal Geer test using 2 mm. dumbbell specimens. As a measure for stress relaxation the time is used that is required to obtain 50% of the value of the interpolated modulus at 200% elongation 6 seconds after the straining zero time at 110°C. The parameter for the aging test is the time in days at 70°C. for the 50% value of tensile strengths. The range for the stress relaxation parameter may be estimated to 8–1200 min. and the aging parameter from 10–600 days. Finally the concordance of temperature coefficient for relaxation and oxidation rates is shown.     

Stabilization effect of potential antioxidants on the thermooxidative stability of styrene–butadiene rubber

Effects of several heterocyclic compounds containing nitrogen, trisubstituted amines and diamines and molecules based on N,N,N′,N′,N′′,N′′-substituted-[1,3,5]triazine-2,4,6-triamine in preventing thermooxidative degradation of styrene–butadiene rubber (SBR) have been studied using non-isothermal DSC measurements. The aim of this study was to determine and compare the stabilizing effect of individual compounds and to select the structures with the best antioxidative properties. In order to compare the stabilizing effect of the compounds, induction periods and protection factors have been calculated. The treatment of the experimental data was carried out using a method based on a non-Arrhenian temperature function. The results show that better antioxidative properties can be assigned to heterocyclic compounds. On the other hand, molecules containing triazine structures exhibited only negligible stabilizing effect on SBR at lower temperatures and even destabilizing effect at higher temperatures.     

The effect of chlorosulphonated polyethylene on thermal properties and combustibility of butadiene–styrene rubber

This article describes the test results of thermal properties and flammability of the unconventionally cross-linked blends of chlorosulfonated polyethylene (CSM) and butadiene–styrene rubber (SBR) by means of zinc oxide or nano-zinc oxide. The thermal curves have been interpreted from the point of view of the chemical transitions of elastomers and their blends. It has been found that the content of combined chlorine in CSM exerts a significant influence on the cross-linking kinetics of CSM/SBR blends, their thermal properties and flammability.     

Viscoelastic behaviour of silica filled natural rubber composites – Correlation of shear with elongational testing

Dynamic mechanical behaviour of natural rubber-silica composites was studied by a frequency sweep method at different temperatures (40 °C,70 °C and 100 °C) using a dynamic mechanical analyzer and a rotorless rheometer, RPA, in an attempt to establish a correlation between the two. The composites with silica content up to 40 phr were studied. It was found that the dependence of dynamic modulus on the frequency as obtained from both the instruments followed a similar trend. This suggests that the dynamic mechanical properties of rubber compounds can be determined even during curing. A correlation could be arrived at between the two sets of data, making it possible to predict one set knowing the other. The impact of silane coupling agent, bis (3-triethoxysilylpropyl tetrasulphide), TESPT, on viscoelasticity was also investigated. The mechanical properties were improved in the presence of TESPT. Additionally, an increase in thermal stability was also observed in the presence of TESPT. Scanning electron micrographs showed the better filler dispersion in the case of silane-coupled silica composites.     

In situ silica reinforcement of methyl methacrylate grafted natural rubber by sol–gel process

In situ silica reinforcement of natural rubber (NR) grafted with methyl methacrylate (MMA) (MMA-GNR) was achieved via the sol–gel reaction of tetraethoxysilane (TEOS) by the use of solid rubber and latex solutions. Silica contents within the MMA-GNR as high as 48 and 19 phr were obtained when using the solid rubber and latex solutions, respectively, under optimum conditions. The conversion efficiency of TEOS to silica was close to 95%. The in situ formed silica MMA-GNR/NR composite vulcanizates were prepared. MMA-GNR/NR composite vulcanizates reinforced with the in situ formed silica prepared by either method had similar mechanical properties to each other, but a shorter cure time and higher mechanical properties than those reinforced with the commercial silica at 9 phr. The TEM micrographs confirmed that the in situ formed silica particles were well dispersed within the MMA-GNR/NR composite matrix, whilst the commercial silica particles showed a significant level of agglomeration and a lower level of dispersion.     

Aminopropyl-modified silica as cross-linkers of polysiloxane containing γ-chloropropyl groups for preparing heat-curable silicone rubber

A series of aminopropyl-modified silica (APS) with different amine contents was prepared and, subsequently, used as cross-linkers of polysiloxane containing γ-chloropropyl groups (CPPS) to prepare heat-curable silicone rubber (MCSR). The dispersion of APS in polysiloxane matrix was studied by scanning electron microscopy. The curing characteristics, mechanical and thermal properties of the MCSR were analyzed by a rheometer, mechanical testing and thermal gravimetric analysis (TGA), respectively. The effects of the silica (TS530) content and the molar ratio of APS/CPPS on the curing characteristics were studied. The influence of the amounts of TS530 and APS, and the kind of APS, on the comprehensive mechanical properties of MCSR is discussed. The optimized conditions to prepare MCSR were obtained as follows: the amount of TS530, 55 parts per hundreds of polysiloxane in weight; the molar ratio of [NH]/[γ-chloropropyl], 1.5: 1; and the amount of amino groups on the surface of APS, 0.65 mmol/g. Additionally, TGA results show that MCSR has high thermal stability.