Miscibility and thermal stability of poly(vinyl alcohol)/chitosan mixtures

The miscibility and the thermal behaviour of chitosan acetate (ChA) with poly(vinyl alcohol) (PVA) have been investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and dynamic mechanical analysis (DMA). Chitosan is blended with poly(vinyl alcohol) in acetic acid solution and this solution is cast to prepare the blend film. From thermal curves the thermal transitions: T_g, T_m and characteristic temperatures of decomposition: T_di, T_max have been determined and compared. The influence of the degree of PVA hydrolysis on the thermal properties of blend systems has been discussed.Based upon the observation on the DSC analysis, the melting point of PVA is decreased when the amount of ChA in the blend film is increased. Though some broadening of the transition curves could be noticed (DSC, TGA and DMA), the obtained results suggest that in the solid ChA/PVA blends the components are poorly miscible. Only PVA sample with relatively low DH = 88% and hence low degree of crystallinity shows partial miscibility with ChA of relatively low molecular weight.     

Miscibility of cellulose acetate with vinyl polymers

Binary blend films of cellulose acetate (CA) with flexible syntheticpolymers including poly(vinyl acetate) (PVAc), poly(N-vinyl pyrrolidone) (PVP),and poly(N-vinyl pyrrolidone-co-vinyl acetate) [P(VP-co-VAc)] were preparedfrommixed polymer solutions by solvent evaporation. Thermal analysis by DSC showedthat CA of any degree of substitution (DS) was not miscible with PVAc, but CAwith DS less than 2.8 was miscible with PVP to form homogeneous blends. Thestate of mixing in CA/P(VP-co-VAc) blends was affected not only by the DS of CAbut also by the VP/VAc copolymer composition. As far as CAs of DS<2.8 andP(VP-co-VAc)s with VP contents more than ca. 25 mol% were used,theCA/copolymer blends mostly showed a miscible behaviour irrespective of themixing ratio. FT-IR measurements for the miscible blends of CA/PVP andCA/P(VP-co-VAc) revealed the presence of hydrogen-bonding interactions betweenresidual hydroxyls of CA and carbonyls of N-vinyl pyrrolidone units, which maybe assumed to largely contribute to the good miscibility.     

Miscibility,morphology and fracture toughness of epoxy resin/poly(vinyl acetate) blends

Diglycidylether of bisphenol A (DGEBA)/poly(vinyl acetate) (PVAc) blends cured with 4,4-diaminodiphenylmethane (DDM) were prepared. The miscibility and phase behavior were investigated by means of differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM). The study results indicate that the epoxy precursor (DGEBA)/PVAc blends are clearly miscible at the entire composition and theTg values experimentally obtained are in a good agreement with those predicted by Fox equation. Cured at elevated temperature, all the DDM-cured blends underwent phase separation and display two-phase morphology. When PVAc content is more than 10 wt%, the thermoplastics-modified resins began to show a co-continuous phase structure. It is the cocontinuous structure that leads to a significantly-improved toughness inK _ic. Morphologic investigation of the surfaces of fracture mechanic measurement specimens indicates that the toughening effect of the thermoplastics-modified epoxy resins may arise mainly from the ductile yielding of PVAc.     

Phase relations in blends of poly(vinyl chloride) with copolymer of ethylene-vinyl acetate and the effects of thermal stabilizers

Further investigations of the system PVC-EVA, with wide line NMR, have shown that the phase relations differ for graft-polymerized samples and non-grafted samples prepared by milling the polymer components together. The phase relations of the grafted products are not appreciably changed by different types of processing and heat treatments. In the non-grafted samples, considerable phase separation is observed by heat treatment at the normal temperatures of processing. It is also shown that the metal-laurates, normally used for thermal stabilization, have good solubility in the PVC-phase and that co-stabilizers of phosphites and epoxides show considerable solubility in the EVA-phase. By heat treatment of milled products at the processing temperature, the co-stabilizers are to some degree transferred from the PVC- to the EVA-phase.     

An NMR investigation of compatibility in blends of poly vinyl chloride and ethylene-vinyl acetate copolymer

A series of technical composite suspension polymerized poly vinyl chloride products with additions of ethylene-vinyl acetate copolymer (Levapren 450M. 45 wt % VAc) have been investigated with NMR. Partial compatibility is found in these samples, and the phase conditions have been shown to be very much dependent upon the methods of forming of the materials. Complete phase separation is observed after prolonged heating.     

A DSC investigation of compatibility in blends of poly vinyl chloride and ethylene-vinyl acetate copolymer

In DSC-thermograms from blends of suspension-polymerized vinyl chloride and ethylenevinyl acetate copolymer (Levapren 450M, 45 wt % VAc), two glass transitions are observed. The transition temperatures are shifted towards each other. In precipitated samples, intermediate phases seem to be formed. The PVC-EVA (45 wt % VAc) system can be regarded as semi-compatible.     

Head-to-head vinyl chloride–vinyl acetate copolymer

Addition chlorination of cis-1,4-polybutadiene in the presence of acetic acid as a cosolvent resulted in the formation of head-to-head vinyl chloride–vinyl acetate copolymer. Chlorine analysis, IR, and NMR spectra of the chlorinated polybutadiene indicated that reaction was primarily double bond addition; there was little evidence for substitutive chlorination. Acetate was incorporated by nucleophilic participation of the acetic acid cosolvent. The extent of incorporation of the acetate group in the polymer chain was a function of the acetic acid concentration. Both the glass transition temperatures and the densities of the chloroacetylated polymers decreased as the degree of acetylation increased.     

Miscibility studies on blends of cellulose acetate and nylon 6

Miscibility studies on cellulose secondary acetate(CA)/Nylon 6(N6) blends have been carried out in this work. Dilute solution viscometry for the blend solutions using formic acid as the common solvent shows the existence of miscibility window.     

Effect of EVA copolymer containing different VA content on the thermal and rheological properties of bio-based high-density polyethylene/ethylene vinyl acetate blends

The effect of ethylene vinyl acetate (EVA) concentration and vinyl acetate (VA) content of EVA on the mechanical, morphological, and rheological properties of bio-based high-density polyethylene (BioPE)/EVA blends was investigated. The blends were characterized by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy, and rheological measurements under oscillatory shear flow. The degree of crystallinity of BioPE decreased with the increase in the EVA concentration and was unaffected with the increase in the VA content. DMTA results showed a decrease in the storage modulus (E′) with the increase in EVA content and that the BioPE/EVA19 blends showed higher E′ values than BioPE/EVA28 blend. The impact strength substantially increased with the addition of EVA concentration above 5 mass% and was higher for the blends containing the highest VA content. The blends containing a higher content of VA exhibited the higher EVA dispersed phase domain size, which increased with the increase in EVA concentration. The complex viscosity increased with the increase in the EVA content, being higher for the BioPE/EVA blends containing higher VA content. The storage modulus increased, at low frequencies, with the increase in the EVA content and can be ascribed to the increase in the EVA dispersed phase domain size.

     

Miscibility and ferroelectric behavior in blends of poly(vinylidene fluoride/trifluoroethylene) and poly(vinyl acetate)

The blend system containing a poly(vinylidene fluoride/trifluoroethylene) [P(VDF/TrFE)] copolymer (68/32 mol %) and poly(vinyl acetate) (PVAc) was miscible from the results of differential scanning calorimetry (DSC) studies that exhibit the presence of a single, composition‐dependent glass transition temperature (T_g) and a strong melting point depression for the semicrystalline P(VDF/TrFE) component. However, differences between the DSC and dielectric measurements, which showed a separate P(VDF/TrFE) T_g peak, suggests that the P(VDF/TrFE)/PVAc blends are actually partially miscible. Because of the lower dielectric constant of PVAc and the reduced sample crystallinity caused by the addition of PVAc, both the dielectric constant and the remanent polarization of the copolymer blends decrease with increasing PVAc content. The presence of a small amount of PVAc stabilized the anomalous ferroelectric behavior of ice–water‐quenched P(VDF/TrFE), and the blend portrayed normal polarization reversal behavior after adding only 1 wt % PVAc. The piezoelectric response suggests small changes with an increasing number of poling cycles. It is believed that PVAc affects the D‐E hysteresis behavior at the interface between crystalline and amorphous phases, although much work remains to be done to confirm this hypothesis. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 927–935, 2003     

Aza-Morita-Baylis-Hillman reaction of ethyl (arylimino)acetate with methyl vinyl ketone and ethyl vinyl ketone

Aza-Morita-Baylis-Hillman (aza-MBH) reaction of ethyl (arylimino)acetate with methyl vinyl ketone and ethyl vinyl ketone has been investigated. We found that aza-MBH adducts 1 could be formed in the presence of DABCO (30 mol %) and the corresponding adducts 2 could be obtained in the presence of PPh₃ (30 mol %) in moderate to good yields in acetonitrile under mild conditions, respectively.     

Miscibility as a function of copolymer composition in blends of a random copolymer and a homopolymer

Random copolymers of n-butyl acrylate (BA) and cyclohexyl acrylate (CHA) were synthesized by solution polymerization in cyclohexane. Blends of polystyrene with the poly(CHA-stat-BA) copolymers were prepared by solvent casting and coprecipitation. The miscibility of the blends was characterized by means of differential scanning calorimetry. While blends with a low content of CHA in the copolymer showed two characteristic glass-transition temperatures of the corresponding blend components, those with a CHA content higher than 70% presented good compatibility. Phase separation of the miscible blends took place after annealing at 200 °C for 1 h, which implies an upper miscibility gap (lower critical solution temperature).     

Irradiation effects on thermal,surface, and physicomechanical properties of ethylene and vinyl acetate copolymer

The structural and thermal transitions for ethylene and vinyl acetate copolymer (EVA) samples irradiated by fast electrons at doses in the range of 2.5–25 Mrad were investigated by DSC and X-ray diffraction analysis. The parameters of chemical bonds in the amorphous phase of copolymer were determined. The change in the degree of crystallinity, melting temperature, and crystallite sizes before and after radiochemical modification were estimated. The obtained results were analyzed and corresponded to the physicomechanical properties of copolymers. The surface energy of copolymers before and after irradiation was defined. The strength of adhesive joints based on EVA from PET substrates and the influence of radiochemical modification of adhesive before joint formation on its strength were analyzed.     

Carbon-13 NMR of poly(vinyl acetate) and ethylene–vinyl acetate copolymer

Carbon-13 nuclear magnetic resonance spectra of atactic poly(vinyl acetate) and ethylene–vinyl acetate copolymers are reported and analyzed. Carbon spectra at 22.6 and 62.9 MHz together with use of shift reagents have permitted a more complete assignment than previously reported; in some cases the published assignments are found to be in error.     

Morphology, thermal stability and visco-elastic properties of polystyrene-poly(vinyl chloride) blends

The morphology, thermal and mechanical properties of polystyrene (PS) blends with 2.5-20 wt% of poly(vinyl chloride) (PVC) have been studied. The measurement of the glass transition temperature (T_g) from the maxima of tan δ data using dynamic mechanical thermal analysis showed that the blends were incompatible and homogenously distributed only within a limited range of PVC contents in PS. The value of the storage modulus was found to increase initially but then decreased with further addition of PVC in the matrix. Distribution of the phases in the virgin and degraded blends was also studied through scanning electron microscopy. The thermogravimetric studies on these blends were carried out under inert atmosphere from ambient to 800 °C at different heating rates varying from 2.5 to 20 °C/min. The thermal decomposition temperatures of blends were found higher than that of pure PS which indicated the stabilizing effects of PVC on PS. The effect varies with the heating rates and the composition of the blends and the phenomenon has been explained due to changing morphology of the blends with composition and the degradation time which affect the interfacial interaction between the degrading products from the polymer components. The kinetic parameters of the degradation process calculated from a method described by Ozawa have been reported for these blends.     

Ethylene/vinyl acetate copolymer/clay nanocomposites

This article highlights the history, synthetic routes, material properties, and scope of ethylene/vinyl acetate copolymer (EVA)/clay nanocomposites. These nanocomposites of EVAs are achieved with either unmodified or organomodified layered silicates with different methods. The structures of the resulting polymer/inorganic nanocomposites have been characterized with X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The addition of a small amount of clay, typically less than 8 wt %, to the polymer matrix unusually promotes the material properties, such as the mechanical, thermal, and swelling properties, and increases the flame retardancy of these hybrids. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 471–480, 2006     

Miscibility behaviour of blends of a thermoplastic polyester polyurethane with vinyl polymers

A method based on the intrinsic viscosities of transfer has been used to predict miscibility of polymer blends. This method has been applied to study the change in the phase behaviour of a microphase separated polyester polyurethane (PSPU) on blending with polyvinyl chloride (PVC), polyvinyl acetate (PVAc) and a vinyl chloride-vinyl acetate copolymer (VCVAc). The PVC/PSPU blends are found to exhibit complete miscibility over the entire composition range. PVAc/PSPU blends show immiscibility while VCVAc/PSPU blends show partial miscibility. Thermal analysis and scanning electron microscopic studies of the blend films have confirmed the results evaluated on the basis of the viscosity method.     

Rheology, morphology and mechanical properties of polyethylene/ethylene vinyl acetate copolymer (PE/EVA) blends

Rheology, morphology and mechanical properties of binary PE and EVA blends together with their thermal behavior were studied. The results of rheological studies showed that, for given PE and EVA, the interfacial interaction in PE-rich blends is higher than EVA-rich blends, which in turn led to finer and well-distributed morphology in PE-rich blends. Using two different models, the phase inversion composition was predicted to be in 45 and 47 wt% of the PE phase. This was justified by morphological studies, where a clear co-continuous morphology for 50/50 blend was observed. The tensile strength for PE-rich blends showed positive deviation from mixing rule, whereas the 50/50 blend and EVA-rich blends displayed negative deviation. These results were in a good agreement with the results of viscoelastic behavior of the blends. The elongation at break was found to follow the same trend as tensile strength except for 90/10 PE/EVA blend. The latter was explained in terms of the effect of higher co-crystallization in 90/10 composition, which increased the tensile strength and decreased the elongation at break in this composition. The results of thermal behavior of the blends indicated that the melting temperatures of PE and EVA decrease and increase, respectively, due to the dilution effect of EVA on PE and nucleation effect of PE on EVA.