Effect of oxyfluorination on electromagnetic interference shielding of polyaniline-coated multi-walled carbon nanotubes

Highly conducting polyaniline (PANi)-coated multi-walled carbon nanotubes (MWCNTs) were prepared by in situ polymerization method for electromagnetic interference shielding. The thickness of the PANi coatings was controlled by the oxyfluorination treatment on the multi-walled carbon nanotubes and analyzed with both SEM and TEM. The oxyfluorination with higher oxygen content produced more hydrophilic functional groups on the surface of multi-walled carbon nanotubes. The functional groups led to the well distribution and coating of PANi on the multi-walled carbon nanotubes resulting in the higher interfacial affinity between them. The uniform coating of PANi on MWCNTs by controlling the oxyfluorination conditions also played a crucial role in increasing the electrical conductivity of nanocomposites. The improved interfacial affinity resulted in the higher electromagnetic interference (EMI) SE of 47.03?dB based on the synergistic combination of the conductive components. The EMI shielding mechanism of PANi on MWCNTs suggested that EMI was mainly shielded by adsorption to avoid secondary EMI.     

EMI shielding and microwave absorption behavior of Au‐MWCNT/polyaniline nanocomposites

Electrically conducting Au‐multiwalled carbon nanotube/polyaniline (Au‐MWCNT/PANi) nanocomposites were synthesized by two different ways: (1) by direct mixing of MWCNT/PANi and Au nanoparticles (Au‐MWCNT/PANi‐1) and (2) by in situ polymerization of aniline in the presence of both MWCNTs and Au nanoparticles (Au‐MWCNT/PANi‐2). The higher electrical conductivity of Au‐MWCNT/PANi‐2 compared with the other samples (PANi, MWCNT/PANi, Au‐MWCNT/PANi‐1) is supported by the red shifts of the UV‐vis bands (polaron/bipolaron), the high value of the –NH+= stretch peak (Fourier transform infrared spectroscopy studies), the high % crystallinity (X‐ray diffraction analysis) and more uniform dispersion of the Au NPs in the material. The performance of the samples in electromagnetic interference (EMI) shielding and microwave absorption was studied in the X‐band (8–12 GHz). For all the samples, absorption was the dominant factor contributing toward the EMI shielding. Au‐MWCNT/PANi‐2 showed the best performance with a total shielding effectiveness of ?16 dB [averaged over the X‐band (GHz)] and a minimum reflection loss of ?56.5 dB. The higher dielectric properties resulting from the heterogeneities because of the presence of nanofillers and the high electrical conductivity lead to the increased EMI shielding and microwave absorption. The results show the significance of both Au nanoparticles and method of synthesis on the EMI shielding performance of MWCNT/PANi composites. Copyright © 2016 John Wiley & Sons, Ltd.     

Electromagnetic interference shielding effectiveness and microwave absorption properties of thermoplastic polyurethane/montmorillonite‐polypyrrole nanocomposites

In this work, thermoplastic polyurethane‐filled montmorillonite‐polypyrrole (TPU/Mt‐PPy) was prepared through melt mixing process for using in electromagnetic shielding applications. The effect of conducting filler content and type, sample thickness, and X‐band frequency range on the electromagnetic interference shielding effectiveness (EMI SE) and EMI attenuation mechanism was investigated. A comparative study of electrical and microwave absorption properties of TPU/Mt‐PPy nanocomposites and TPU/PPy blends was also reported. The total EMI SE average and electrical conductivity of all Mt‐PPy.Cl or Mt‐PPy.DBSA nanocomposites are higher than those found for TPU/PPy.Cl and TPU/PPy.DBSA blends. This behavior was attributed to the higher aspect ratio and better dispersion of the nanostructured Mt‐PPy when compared with neat PPy. Moreover, the presence of Mt‐PPy into TPU matrix increases absorption loss (SE_A) mechanism, contributing to increase EMI SE. The total EMI SE values of nanocomposites containing 30 wt% of Mt‐PPy.DBSA with 2 and 5 mm thickness were approximately 16.6 and approximately 36.5 dB, respectively, corresponding to the total EMI of 98% (75% by absorption) and 99.9% (88% by absorption). These results highlight that the nanocomposites studied are promising materials for electromagnetic shielding applications.     

Microstructure,electrical, and electromagnetic interference shielding properties of carbon nanotube/acrylonitrile–butadiene–styrene nanocomposites

Processing, electrical, and electromagnetic interference (EMI) shielding behaviors of carbon nanotube (CNT)/acrylonitrile–butadiene–styrene (ABS) nanocomposites were studied as function of CNT concentration. The nanocomposites were prepared by melt mixing followed by compression molding. The selective and good level of dispersion of CNT in the styrene–acrylonitrile section of the ABS polymer was found to create conductive networks in the ABS matrix at a nanofiller loading of 0.75 wt %. At this nanofiller loading, the nanocomposite electrical conductivity was 10^?5 S/m. This conductivity makes the nanocomposite suitable for electrostatic discharge protection applications. The EMI shielding effectiveness of the nanocomposites increased with the increase in nanofiller concentration. In the 100–1500 MHz frequency range, 1.1 mm thick plates made of ABS nanocomposite filled with 5 wt % CNT exhibit an EMI shielding effectiveness of 24 dB. At this shielding level, the nanocomposite is suitable for a broad range of applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Carbon Papers from Tall Goldenrod Cellulose Fibers and Carbon Nanotubes for Application as Electromagnetic Interference Shielding Materials

To transform tall goldenrods, which are invasive alien plant that destroy the ecosystem of South Korea, into useful materials, cellulose fibers isolated from tall goldenrods are applied as EMI shielding materials in this study. The obtained cellulose fibers were blended with CNTs, which were used as additives, to improve the electrical conductivity. TGCF/CNT papers prepared using a facile paper manufacturing process with various weight percent ratios and thickness were carbonized at high temperatures and investigated as EMI shielding materials. The increase in the carbonization temperature, thickness, and CNT content enhanced the electrical conductivity and EMI SE of TGCF/CNT carbon papers. TGCF/CNT-15 papers, with approximately 4.5 mm of thickness, carbonized at 1300 °C exhibited the highest electrical conductivity of 6.35 S cm⁻¹, indicating an EMI SE of approximately 62 dB at 1.6 GHz of the low frequency band. Additionally, the obtained TGCF/CNT carbon papers were flexible and could be bent and wound without breaking.     

Immobilization of gold nanoparticles on poly(methyl methacrylate) electrospun fibers exhibiting solid‐state surface plasmon effect

In this study, the surface plasmon effect of Au nanoparticles was successfully realized in the solid state by embedding the Au nanoparticles on the surface of the transparent polymer fibers for the first time. Electrospinning a poly(methyl methacrylate) (PMMA) and HAuCl₄ mixture followed by a wet chemical reduction, the gold nanoparticles were formed on the PMMA nanocomposite electrospun fibers in a well‐distributed manner to give photostable purple color. The Au nanoparticles were all sphere shaped with an average diameter of 12 nm. Specifically, simply adjusting HAuCl₄ salt concentration in the electrospinning solution, it is able to control the electrospun fiber diameter and gold nanoparticle content in the resulting PMMA/Au nanocomposite fibers. Therefore, the developed method described herein is simple and effective for the large volume production of PMMA/Au nanocomposite fibers. Copyright © 2011 John Wiley & Sons, Ltd.     

Ultrafine Electrospun Conducting Polymer Blend Fibers and Their Photoluminescence Properties

Ultrafine poly(2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylene-vinylene) (MEH-PPV)/polyvinylpyrrolidone (PVP) blend fibers with the average diameters ranging from 625 nm to 1.46 µm were prepared by electrospinning of polymer blend solutions in the mixed solvent of chlorobenzene and methanol. The average diameter of fibers was found to decrease with initial increase in the applied electrical potential and composition of MEH-PPV, reach a minimum value at an intermediate value, and increase with further increase in the applied electrical potential and composition of MEH-PPV, while it was found to decrease with increasing collection distance. PVP was easily removed from MEH-PPV/PVP fibers by the Soxhlet extraction, and after the removal of PVP at high composition of MEH-PPV, pure MEH-PPV fibers were obtained as a ribbon-like structure aligned with wrinkled surface in fiber direction. The increase in MEH-PPV composition and the removal of PVP from as-spun MEH-PPV/PVP fibers resulted in a significant blue-shift in UV-Vis absorption peak and red-shift in PL peak.     

Asymmetric Ni/PVC films for high-performance electromagnetic interference shielding

A novel asymmetric Ni/PVC film has been developed by solution casting method. The structure, electrical conductivity, electromagnetic interference(EMI) shielding, and impact resistance were investigated. The results showed that the Ni particles were asymmetrically distributed along the thickness direction in the film. The top surface resistivity increased with film thickness, while the bottom surface exhibited the different trend. EMI shielding effectiveness(SE) depended on formation of closed packed conductive Ni network, which was influenced by both Ni content and film thickness. A linear relationship was observed between EMI SE and film thickness. The films with lower Ni content showed the faster increasing rate of EMI SE with film thickness. Some of the films show appreciably high EMI SE( 40 d B), indicating the promising application in EMI shielding field. Moreover, the films exhibit different impact performance under different impacting directions. All the experimental facts demonstrate that the asymmetric structure endows the film achieving high-performance EMI shielding function.     

Electrically conducting electrospun silk membranes fabricated by adsorption of carbon nanotubes

We present a simple method of obtaining electrically conducting electrospun silk non-woven membranes consisting of nanofibers with multi-walled carbon nanotubes (MWCNTs) adsorbed on their surface. Nanofibrous membranes with fibroin diameters of 460 ± 40 nm were formed from aqueous Bombyx mori fibroin solution by electrospinning. The MWCNTs adhered well to the surface of the highly porous silk nanofibrous membranes when Triton X-100 was used as the surfactant for the dispersion of the MWCNTs in aqueous media. The electrical conductivity of the membranes was 2.4 × 10⁻⁴ S/cm due to the presence of the MWCNTs on their surface. In addition, the strong interaction between the MWCNTs and nanofibers keeps them from separating each other, even after ultrasonication. The combination of the high conductivity of the membranes and the simple process used to fabricate them could lead to significant advances in the development of new materials, such as electromagnetic interference shielding or electrostatic dissipation membranes.     

Electromagnetic interference shielding Ti_3C_2T_x-bonded carbon black films with enhanced absorption performance

The demand for flexible and freestanding electromagnetic interference(EMI) shielding materials are more and more urgent to combat with serious electromagnetic(EM) radiation pollution.Twodimensional Ti_3C_2T_x is considered as promising EMI shielding material to graphenes because of the low cost and high electrical conductivity.However,the shielding performance still needs to be optimized to decrease the reflection effectiveness(SE_R) and increase absorption effectiveness(SEA).Herein,we prepared Ti_3C_2T_x-bonded carbon black films with a porous structure.The SE_R decreased from 20 dB to12 dB and the SEA increased from 31 dB to 47 dB.The best EMI shielding effectiveness can be as high as60 dB with SE_A of 15 dB and SE_R of45 dB.Their calculated specific shielding effectiveness can be as high as8718 dB cm~2/g.These results indicate that the porous structure can enhance the absorption of the EMI shielding films,resulting from the enhanced scattering and reflectio n.Conseque ntly,this work provides a promising MXene-based EMI shielding film with lightweight and flexibility.     

Polymerization and characterization of high conductivity and good adhension polypyrrole films for electromagnetic interference shielding

<正>Polypyrrole(PPy) shows a favorable application in the electromagnetic interference(EMI) shielding due to its good electrical conductivity and outstanding air stability.Conducting PPy films with high conductivity and good adhesion were successfully polymerized on the surface of insulating epoxy resin substrates using chemical polymerization.The factors affecting the properties of PPy films,such as the surface morphology,adhesion between PPy film and substrate,electrical conductivity,EMI shielding effectiveness(SE),were investigated.The adhesion was improved significantly through a three-step surface pretreatment of epoxy resin substrates including removing impurities,roughening,and surface modification with silane coupling agent.An enhancement in the conductivity of PPy films of about one order of magnitude was achieved by adding dopant in FeCl_3 solution.The higher the conductivity,the better the shielding effectiveness.Taking sodium p-toluenesulfonate doped PPy film as example,EMI SE was in the practically useful range of about 30 dB over a wide frequency range from 30 MHz to 1500 MHz.The PPy film samples were characterized by scanning electron microscopy (SEM),infrared spectra(IR),X-ray photoelectron spectroscopy(XPS) and the flange coaxial transmission device.The fourpoint probe method was used to measure conductivity of PPy films.     

Novel antibacterial fibers of quaternized chitosan and poly(vinyl pyrrolidone) prepared by electrospinning

The preparation of continuous defect-free fibers from quaternized chitosan derivative (QCh) has been achieved by electrospinning of mixed aqueous solutions of QCh with poly(vinyl pyrrolidone) (PVP). The average fiber diameter significantly decreases from 2800 to 1500 nm on increasing the polyelectrolyte content. In order to impart to QCh/PVP electrospun fibers stability to water and water vapor, the fibers have been crosslinked by incorporation of photo-crosslinking additives into QCh/PVP spinning solutions and subsequent UV irradiation of the electrospun fibers. Photo-crosslinked QCh-containing electrospun mats show high antibacterial activity against the Gram-positive bacteria Staphylococcus aureus and Gram-negative bacteria Escherichia coli.     

Recent progress in MXene and graphene based nanocomposites for microwave absorption and electromagnetic interference shielding

There is widespread use of telecommunication and microwave technology in modern society, and raised the electromagnetic interference (EMI) issue to alarming situation due to apprehensive demand and growth of 5G technology undesirably disturbing the human health. The two dimensional (2D) materials including graphene and MXenes are already been used for variety of electronic devices due to their exceptional electrical, mechanical, optical, chemical, and thermal properties. MXene is composed of metal carbides, in which mainly metals are the building blocks for dielectrics, semiconductors, or semimetals. However, the strong interfaces with electromagnetic waves (EM) are variable from terahertz (THz) to gigahertz (GHz) frequency levels and are widely used in EMI and Microwave absorption (MA) for mobile networks and communication technologies. The use of different organic materials with metal, organic, inorganic fillers, polymers nanocomposite and MXene as a novel material has been studied to address the recent advancement and challenges in the microwave absorption mechanism of 2D materials and their nanocomposites. In this concern, various techniques and materials has been reported for the improvement of shielding effectiveness (SE), and theoretical aspects of EMI shielding performance, as well stability of 2D materials particularly MXene, graphene and its nanocomposites. Consequently, various materials including polymers, conducting polymers, and metal–organic frameworks (MOF) have also been discussed by introducing various strategies for improved MA and control of EMI shieling. Here in this comprehensive review, we summarized the recent developments on material synthesis and fabrication of MXene based nanocomposites for EMI shielding and MA. This research work is a comprehensive review majorly focuses on the fundamentals of EMI/MA.  The recent developments and challenges of the MXene and graphene based various structures with different polymeric composites are described in a broader perspective.     

Enhanced Conductivity and mechanical properties of polyimide based nanocomposite materials with carbon nanofibers via carbonization of electrospun polyimide fibers

Carbon nanofibers (CNF) have been obtained by the thermal treatment of the electrospun polyimide fibers in our present work. The carbon structure and surface morphology of the as-received CNFs were investigated using X-ray diffraction, Raman spectroscopy, and scanning electron microscopy. Investigations of the nanocomposite materials fabricated using these CNFs as conductive fillers and polyimide as matrix show that the presence of CNFs can improve both the mechanical and electrical properties of the material. The conductivity of the nanocomposite films increases with increases in the CNF content and a percolation threshold of about 6.3 vol % (0.0785 in weight fraction) is calculated according to percolation theory.     

二氧化碳-环氧丙烷共聚物电纺纤维形貌研究

利用电纺丝技术制备了二氧化碳环氧丙烷共聚物超细纤维,研究了喷丝口电势、纺丝距离、浓度、溶剂等因素对纤维形貌、直径及均一性的影响.实验结果表明,利用电纺丝法可以制备直径在小于200nm到7μm二氧化碳环氧丙烷共聚物纤维;喷丝口电势和浓度对于共聚物电纺丝纤维是否形成串珠结构有重要影响;电势、距离和纺丝液浓度都对纤维直径及分散系数有较大影响,在一定范围内,随着喷丝口电势增加,纤维平均直径变大而分散系数变小;纺丝距离增大使得纤维平均直径变小,分散系数变大;浓度的增大使得纤维平均直径变大,分散系数变小;不同溶剂配制的溶液体系制备的电纺丝纤维形貌有很大差异,在二氯甲烷和丁酮的体系中,分别观察到了两组较为集中的直径分布.     

Free surface electrospinning of fibers containing microparticles

Many materials have been fabricated using electrospinning, including pharmaceutical formulations, superhydrophobic surfaces, catalysis supports, filters, and tissue engineering scaffolds. Often these materials can benefit from microparticles included within the electrospun fibers. In this work, we evaluate a high-throughput free surface electrospinning technique to prepare fibers containing microparticles. We investigate the spinnability of polyvinylpyrrolidone (PVP) solutions containing suspended polystyrene (PS) beads of 1, 3, 5, and 10 μm diameter in order to better understand free surface electrospinning of particle suspensions. PS bead suspensions with both 55 kDa PVP and 1.3 MDa PVP were spinnable at 1:10, 1:5, and 1:2 PS:PVP mass loadings for all particle sizes studied. The final average fiber diameters ranged from 0.47 to 1.2 μm and were independent of the particle size and particle loading, indicating that the fiber diameter can be smaller than the particles entrained and can furthermore be adjusted based on solution properties and electrospinning parameters, as is the case for electrospinning of solutions without particles.     

Thermal shrinkage of electrospun PVP nanofibers

This paper outlines the shrinkage of electrospun polyvinylpyrrolidone (PVP) fiber mats during thermal treatment. The thermal behavior and phase changes within the fibers were investigated by DSC and TGA/DTA. Five precursors with different PVP loading in ethanol were electrospun. The mats shrinkage as function of temperature was measured in the RT–200 °C range. Shrinkage rate drastically increased above the polymer glass transition point, T_g (150–180 °C), due to increase in polymer chain mobility. Mats shrinkage at 200 °C as function of PVP concentration showed a minimum at ∼10%wt. Below 10% PVP the mats morphology is non‐uniform, consisting of beads and fibers. Above 10% PVP, only flat and uniform fibers were observed. This paper outlines the dominant mechanism governing the mats shrinkage during heating. In addition, the effect of PVP concentration on the expansion of fibers diameter was investigated and found to be consistent with the linear shrinkage observing a minimum at ∼10% PVP. The effect of applied voltage on mat shrinkage was investigated, and showed a minimum at 12 kV. Understanding the interplay between fibers morphology and thermal shrinkage allows precursor composition and system optimization needed for minimizing shrinkage negative effects on the structure and properties of electrospun fiber mats. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 248–254     

Preparation and Characterization of Aligned PLLA/PCL/HA Composite Fibrous Membranes

Aligned poly(L-lactide) (PLLA)/poly(?-caprolactone) (PCL)/hydroxyapaite (HA) composite fibrous membranes were fabricated by electrospinning. Their morphology, thermal stability, mechanical properties, hydrophilic properties and biocompatibility were investigated. The electrospun fibers are highly aligned and the HA are oriented along the fiber axis. When HA are incorporated, the PLLA/PCL/HA composite fibers become thinner due to the increased conductivity. In addition, the aligned HA reinforce the electrospun fibrous membranes. The larger porosity and higher hydrophilic properties induced by HA in the electrospun fibers have improved the degradation of the PLLA/PCL/HA fibrous membranes which have no toxic effect on proliferation of adipose-derived stem cells.     

PHBV电纺纤维结构与形态的研究

利用电纺丝法制备了超细聚 β 羟基丁酸戊酸酯 (PHBV)纤维 ,通过扫描显微镜 (SEM)、差热分析(DSC)、宽角X射线衍射和偏振红外吸收光谱对产品进行了结构与形态的表征 .研究了纺丝过程中溶液浓度、电压和接收距离 3个参数对纤维形态的影响 .结果表明 ,溶液浓度是决定性的 ,只有高于一个定值才能获得单一的纤维产品 .与流延成型的PHBV相比 ,电纺丝具有较高的取向度和结晶度 .原因可能是 ,电场力下喷丝震荡过程中带来的拉伸作用从而引起分子链的规整排列     

Study of superhydrophobic electrospun nanocomposite fibers for energy systems

Polystyrene (PS) and polyvinyl chloride (PVC) fibers incorporated into TiO(2) nanoparticles and graphene nanoflakes were fabricated by an electrospinning technique, and then the surface morphology and superhydrophobicity of these electrospun nanocomposite fibers were investigated. Results indicated that the water contact angle of the nanocomposite fiber surfaces increases to 178° on the basis of the fiber diameter, material type, nanoscale inclusion, heat treatment, and surface porosity/roughness. This is a result of the formation of the Cassie-Baxter state in the fibers via the nanoparticle decoration, bead formation, and surface energy of the nanofiber surface. Consequently, these superhydrophobic nanocomposite fibers can be utilized in designing photoelectrodes of dye-sensitized solar cells (DSSCs) as self-cleaning and anti-icing materials for the long-term efficiency of the cells.