Miniaturised pressurised liquid extraction of chloroanilines from soil with subsequent analysis by large-volume injection-gas chromatography-mass spectrometry

A number of chloroanilines were extracted from soil by means of miniaturised pressurised liquid extraction (PLE). The extraction procedure was optimised for both large-volume on-column (LV-OC) and programmed-temperature vaporisation (PTV) injections combined with GC-MS. Hexane was the only extraction solvent suited for LV-OC and hexane/acetone gave the best results when using a PTV. Overall, the hexane/acetone-plus-PTV procedure shows better results than the hexane-plus-LV-OC method in terms of analyte recovery (36-109% versus 5-87%), repeatability (8-13% versus 4-31%) and detection limits. Both approaches allow detection of the chloroanilines in complex soil samples down to the 5-50 ng/g range. However, the PTV-based procedure is superior as regards robustness: over one hundred samples can be analysed without any maintenance being required.     

Analysis of polycyclic aromatic hydrocarbons in soil and sediment with on-line coupled pressurised hot water extraction,hollow fibre microporous membrane liquid-liquid extraction and gas chromatography

Pressurised hot water extraction (PHWE) was coupled on-line via hollow fibre microporous membrane liquid-liquid extraction (HF-MMLLE) to gas chromatography (GC) and applied in the analysis of polycyclic aromatic hydrocarbons (PAHs) in soil and sediment. In this combination, the MMLLE unit serves as a trapping device for the extracted compounds. Simultaneously it cleans and concentrates the extract, which is then transferred on-line to the GC. No extra clean-up steps are required between the trapping and the transfer to GC. The on-line system gives excellent sensitivity while allowing small sample size. The method was linear, with limits of detection in the range 50-890 pg and limits of quantification 0.11-1.22 microg g(-1). The concentration enrichment factors obtained with the method ranged from 9 to 55. Comparison of the results with those obtained by other techniques confirmed the good performance.     

Miniaturised selective pressurised liquid extraction of polychlorinated biphenyls from foodstuffs

The feasibility of miniaturised pressurised liquid extraction (PLE) with in-cell purification and subsequent gas chromatography with micro-electron capture detection (GC-micro-ECD) for the determination of prioritary and toxic polychlorinated biphenyls (PCBs) in a variety of foodstuffs (fat contents in the range 22-49%, w/w, on a freeze-dried basis) has been investigated. After optimisation of the several experimental parameters affecting the efficiency of the selective PLE process, the developed method provided quantitative recoveries of the endogenous PCBs studied and complete fat elimination in a single step using n-hexane as extraction solvent. A total solvent volume of 3.5 mL was used for the two consecutive 7 min static PLEs of 100-mg samples. Detection limits using GC-micro-ECD were below 0.2 ng/g freeze dried sample for all 22 PCBs investigated in real-life foodstuffs, and the repeatability of the complete PLE plus GC-micro-ECD method as calculated for the analysis of the endogenous PCBs in general was better than 14%. Comparison of the miniaturised PLE method developed with either conventional Soxhlet extraction or matrix solid phase dispersion with subsequent (off-line) clean-up for the analysis of non-spiked samples showed that the efficiency of PLE was similar to or better (recoveries in the range 83-133%, as calculated for the endogenous analytes) than for the other two extraction methods assayed.     

Pressurised liquid extraction of polycyclic aromatic hydrocarbons from contaminated soils

The reliability and efficiency of the pressurised liquid extraction technique (PLE) for extracting polycyclic aromatic hydrocarbons (PAHs) from contaminated soil has been investigated. Experimental design was used to study the influence of seven extraction variables (sample load, solvents used, solvent ratios, pressure, temperature, extraction time, and rinse volume). The results show that large sample loads in combination with small solvent volumes may result in low extraction efficiency. They also indicate that the recovery of low-molecular-mass PAHs is reduced by low extraction temperatures. The exact settings of the other variables are, however, less significant for the extraction efficiency. Repeated extractions at optimised settings of the tested variables show that PLE is an exhaustive extraction technique that generally results in high yields. In addition, extraction of a certified reference material (CRM 103-100) revealed that the method is both accurate and precise. Another finding was that adding the internal standard on top of the soil in the extraction cell causes considerable over-estimation of the concentrations when large samples are extracted with small solvent volumes. This is because the PLE-cell resembles a chromatographic column, so compounds added to the top of the soil layer have a longer distance to travel through the soil compared to the average distance of the native compounds, which are distributed evenly throughout the column. We therefore recommend that the internal standard should be added to the extract immediately after the extraction or, alternatively, carefully mixed with the sample prior to extraction.     

Static pressurised liquid extraction of nitrated polycyclic aromatic hydrocarbons from soils with on-line filtration-preconcentration prior to gas chromatography-mass spectrometry detection

Nitrated polycyclic aromatic hydrocarbons have been extracted from both spiked and natural contaminated soils by using static pressurised liquid extraction. The variables governing the extraction (namely, pressure, extraction time, temperature and number of static extraction cycles) have been optimised using the experimental design methodology. A laboratory-made pressurised liquid extractor has been used allowing its coupling to a filtration-preconcentration system through a flow injection interface, thus providing a partially automated approach. Gas chromatography with MS-MS ion preparation mode has been used for individual separation-identification/quantification providing both high selectivity (no interferences were observed) and sensitivity (detection limits of low pg). The comparison of the proposed approach with the reference EPA Method 3540 has shown that both methods provide similar efficiencies but with dramatic saving of time by the former (30 min vs. 24 h). The use of water as leaching agent avoids the use of organic solvents, thus providing an environmentally friendly method.     

Comparison of the static,dynamic and static-dynamic pressurised liquid extraction modes for the removal of nitrated polycyclic aromatic hydrocarbons from soil with on-line filtration-preconcentration

The three operational modes of pressurised liquid extraction (PLE) (namely, static, dynamic and static-dynamic) have been applied for the extraction of nitrated polycyclic aromatic hydrocarbons from both spiked and natural contaminated soils. A comparison of the three modes in terms of experimental set-up used, extraction time needed for total removal of the analytes and precision has been carried out. The use of a flow-injection manifold as interface between every pressurised extractor and a filtration-preconcentration system has allowed the partial automation of the proposed approaches. Efficiencies close to 100% have been provided by the three operational modes. However, the static-dynamic mode has been proved as the most suitable alternative providing the shortest extraction time (25 min) versus the static (30 min) and the dynamic (50-70 min) modes. Gas chromatography with MS-MS ion preparation mode has been used providing both high selectivity (no interferences were observed) and sensitivity (detection limits of low pg). The comparison of the proposed approaches with the reference method 3540 of the US Environmental Protection Agency (EPA) has shown that both methods provide similar efficiencies with an important shortening in the extraction time (25-70 min by PLE versus 24 h by the EPA method). The use of water as leaching agent has avoided the use of organic solvents providing an environmentally friendly method.     

超高效液相色谱法检测土壤中的多环芳烃

采用二极管阵列(PDA)检测器,建立了超高效液相色谱(UPLC)定性定量分析土壤中16种多环芳烃(PAHs)的方法。并将该方法与传统高效液相色谱(HPLC)的分析性能进行了详细的比较。研究结果表明,采用UPLC法分析16种PAHs具有分析速度快(13.5 min)、检出限低(2～20 pg)、灵敏度高等优点。     

Fluidized-bed extraction of polycyclic aromatic hydrocarbons from contaminated soil samples

Summary Due to the carcinogenity and ubiquity of polycyclic aromatic hydrocarbons in the environment they are of ongoing interest to analytical chemistry. In this study, a comparison of the classic Soxhlet extraction and, fluidized-bed extraction, has been conducted. The extraction of polycyclic aromatic hydrocarbons by this technique has been optimized considering as experimental variables the variation of the number of extraction cycles and the holding time after reaching the heating temperature by means of a surface response design. The significance of the operational parameters of the fluidized-bed extraction on the performance characteristics has been investigated. For the determination of the analytes a selective clean-up of the extracts followed by a fast gas chromatography method with mass spectrometric detection was used, resulting in low limits of detection (0.2 pg μL⁻¹). The accuracy of the complete analytical method was established by extraction and analysis of reference materials.     

Dynamic microwave-assisted extraction coupled on-line with solid-phase extraction: determination of polycyclic aromatic hydrocarbons in sediment and soil

This paper describes a new extraction tool for the determination of polycyclic aromatic hydrocarbons (PAHs) in soil and sediment samples, using dynamic microwave-assisted extraction combined with solid-phase extraction (DMAE-SPE). The critical variables for DMAE-SPE are investigated and optimized in an experimental design. The technique proved to be fast, accurate and able to yield quantitative extraction of PAHs from naturally contaminated sediment and soil samples. The set-up is fully automated and features monitored extraction, which facilitates rapid optimization of the method. In addition, only small quantities of solvent and sample are required.     

Stability of polycyclic aromatic hydrocarbons in pressurised hot water

The stability of seven polycyclic aromatic hydrocarbons (PAHs) were studied in aqueous solutions at 100-350 degrees C. The aqueous solution of one PAH compound at a time was sealed in a stainless steel bomb-type reaction vessel in an argon atmosphere and heated for 10 to 240 min in an oven. The contents of the vessel were analysed by GC-MS. At 300 degrees C, degradation was observed even with the shortest heating time, 10 min. The degradation products were typically different oxidation products such as ketones and quinones. In addition to the heating time and temperature, the concentration of the analyte and the inner surface of the vessel affected the results.     

超高效液相色谱荧光检测器测定土壤中多环芳烃

建立了超高效液相色谱系统(UPLC)荧光检测土壤中15种美国环境保护署(USEPA)优控的多环芳烃(PAHs),简化了土壤样品中PAHs的前处理过程。UPLC对15种PAHs分离时间为17 min,流速为0.4 mL/min。荧光检测器对15种PAHs的检出限为0.03~1.53μg/L,6次重复测定的峰面积相对标准偏差为0.12%~0.99%。除了萘和苊外,土样加标的平均回收率为82.9%~103.4%。由于色谱柱的较高分辨率以及荧光检测器的较高选择性,在定性和定量研究土壤样品中的PAHs时,提取物的硅胶柱净化步骤可以省略。     

Modern state of high-performance liquid chromatography of polycyclic aromatic hydrocarbons

The review is devoted to the recent studies in the field of high-performance liquid chromatography (HPLC) of polycyclic aromatic hydrocarbons (PAHs). The existing certified techniques, developments of synthesis of new sorbents for separating PAH isomers, and study of the retention mechanism are discussed. It also considers the modern methods of extraction and concentration of PAHs, mainly from environmental objects, which are compatible with subsequent identification by HPLC, as well as the necessity of analytical control of contamination of the environment, food sources, and food supplies with PAHs.     

Comparison of adsorbents for on-line solid-phase extraction of polycyclic aromatic hydrocarbons before liquid chromatography with UV detection

Summary On-line solid-phase extraction (SPE) coupled with reversed-phase liquid chromatography and UV detection at 254 nm has been used for the determination of trace-level polycyclic aromatic hydrocarbons (PAH) in soil extracts. Five commercially available adsorbents (C₈, C₁₈, PLRP-S, PRP-1, and Bond-Elut Env) were evaluated. Results showed that recovery of the PAH decreased with increasing molecular weight, because of their poorer solubility. Recovery of high-molecular-weight PAH was significantly improved by addition of 10% (v/v) acetonitrile to the sample before loading of the SPE adsorbent. PAH recovery ranged from 64.0 to 108% when a 50 mL sample spiked with 1 μg L⁻¹ was applied to these adsorbents. Determination of PAH was possible with detection limits below 0.05 μg L⁻¹, which corresponds to 0.2 μg kg⁻¹ soil. The method was successfully used to determine PAH in soil extracts.     

Analysis of polycyclic aromatic hydrocarbons adsorbed on particles of atmospheric interest using pressurised fluid extraction

Pressurised fluid extraction (PFE) was used for the measurement of 13 polycyclic aromatic hydrocarbons (PAHs) adsorbed on different types of particles: two model particles (PAH-coated silica, PAH-coated graphite) and two natural atmospheric particles (urban dust and diesel exhaust, from NIST reference materials). Samples were analysed by gas chromatography coupled to mass spectrometry. Extraction efficiency was evaluated with internal standard recovery yields and was shown to depend on the nature of the particle, on the structure of the analytes and on the PAH concentration. Extraction conditions (toluene, 130°C, 130 bar, 2 × 8-min static cycles) were optimised to extract PAHs when strongly interacting with solid matrices and were validated by the analysis of two PAH-certified materials.     

A two-step supercritical fluid extraction of polycyclic aromatic hydrocarbons from roadside soil samples

A two-step procedure for the supercritical fluid extraction (SFE) of polycyclic aromatic hydrocarbons from soil samples was developed. The procedure consists of a static supercritical fluid treatment in a closed extraction cell at a high temperature (T=250 or 340degreesC for 20 min) and an SFE with a solvent trapping. During the static phase, the sample is exposed to a supercritical organic solvent (methanol, toluene, dichloromethane, ACN, acetone, and hexane). The solvent penetrates particles of the matrix to substitute strongly bonded molecules and dissolves the analytes in the supercritical phase. At ambient temperature, supercritical fluids became liquid and lost their solvation abilities. Most of the analytes condense on the surface of the particles or on the extraction cell walls without forming strong bonds or penetrating deep into the matrix. Thus, the pretreatment liberates the analytes and they behave similar to those in freshly spiked samples. The common SFE with toluene-modified CO2 as an extraction fluid follows the static phase. With the use of the most suitable extraction phases (toluene, ACN), the extraction efficiency of the combined procedure is much higher (approximately100%). The results of the combined procedure are compared to the SFE procedure of the same untreated sample (difference less than 5%) and to the Soxhlet extraction. The extracts were analyzed using a GC with the flame ionization detection.     

Screening and determination of polycyclic aromatic hydrocarbons in seafoods using QuEChERS-based extraction and high-performance liquid chromatography with fluorescence detection

A rapid, sensitive, and accurate method for the screening and determination of polycyclic aromatic hydrocarbons (PAHs) in edible seafood is described. The method uses quick, easy, cheap, effective, rugged, and safe (QuEChERS)-based extraction and HPLC with fluorescence detection (FLD). The method was developed and validated in response to the massive Deepwater Horizon oil spill in the Gulf of Mexico. Rapid and highly sensitive PAH screening methods are critical tools needed for oil spill response; they help to assess when seafood is safe for harvesting and consumption. Sample preparation involves SPE of edible seafood portions with acetonitrile, followed by the addition of salts to induce water partitioning. After centrifugation, a portion of the acetonitrile layer is filtered prior to analysis via HPLC-FLD. The chromatographic method uses a polymeric C18 stationary phase designed for PAH analysis with gradient elution, and it resolves 15 U.S. Environmental Protection Agency priority parent PAHs in fewer than 20 min. The procedure was validated in three laboratories for the parent PAHs using spike recovery experiments at PAH fortification levels ranging from 25 to 10 000 microg/kg in oysters, shrimp, crab, and finfish, with recoveries ranging from 78 to 99%. Additional validation was conducted for a series of alkylated homologs of naphthalene, dibenzothiophene, and phenanthrene, with recoveries ranging from 87 to 128%. Method accuracy was further assessed based on analysis of National Institute of Standards and Technology Standard Reference Material 1974b. The method provides method detection limits in the sub to low ppb (microg/kg) range, and practical LOQs in the low ppb (microg/kg) range for most of the PAH compounds studied.     

Determination of polycyclic aromatic hydrocarbons in marine sediments by high-performance liquid chromatography after microwave-assisted extraction with micellar media

A simple and rapid method is developed for extraction and determination of polycyclic aromatic hydrocarbons (PAHs) in marine sediments. The procedure was based on the microwave-assisted extraction of PAHs in marine sediment samples using a micellar medium of Polyoxyethylene 10 lauryl ether as extractant. Two-level factorial designs have been used to optimize the microwave extraction process. The analysis of extracts has been carried out by HPLC with UV detection. Fortified sediments gave an average recovery between 85.70 and 100.73%, with a relative standard deviation of 1.77-7.0% for PAHs with a ring number higher than three.     

Molecular-shape recognition of polycyclic aromatic hydrocarbons in reversed phase liquid chromatography

Summary The molecular-shape recognition of polycyclic aromatic hydrocarbons has been studied on various stationary phases in reversed-phase high-performance liquid chromatography. The examined stationary phases were phenyl-, diphenyl-, triphenyl- and benzyl-bonded silicas. The results of regression analysis inidcated that triphenylsilica is the best packing material to recognize the difference in the molecular-shape of structural isomers. This fact was confirmed by the separation of 4-ring isomers.     

Effect of extraction vessel geometry and flow homogeneity on recoveries of polycyclic aromatic hydrocarbons in pressurised hot water extraction

Extraction vessels of different length, internal diameter and volume were tested to evaluate the effect of vessel geometry on the recovery of polycyclic aromatic hydrocarbons (PAHs) from certified sediment by pressurised hot water extraction (PHWE). Pressurised hot water extractions were performed at 300 °C with both liquid water (pressure 250 kg cm^–2) and steam (pressure 50 kg cm^–2). In addition, the effects on the recoveries of sediment packing and water flow direction were examined in two vessels. The geometry of the vessel, the packing of the sediment and the flow direction of the water had only minor effect on the recoveries.     

在线固相萃取-液相色谱法直接测定水中超痕量多环芳烃

建立了在线固相萃取-液相色谱直接测定水体中16种超痕量多环芳烃（PAHs）的方法。水样经高速离心后，加入适量甲醇，配制成40%（体积分数）甲醇水溶液，直接进样2 mL至在线固相萃取流路，进行萃取富集，再通过阀切换将洗脱的PAHs转移至分析流路进行分离检测。16种PAHs在各自范围内线性关系良好，相关系数均大于0.996；方法的检出限为0.14~12.50 ng/L，其中苯并[a]芘（B（a）P）的检出限为0.38 ng/L。实际水样在10、40和200 ng/L加标水平下的加标回收率为76.1%~134.9%，RSD为0.3%~16.6%。B（a）P在1 ng/L加标水平下的回收率为71.8%~92.7%，RSD为3.9%。结果表明，该方法操作简单，灵敏度高，溶剂消耗量少，可满足水样中PAHs，尤其是B（a）P的超痕量分析要求。