大孔-介孔Ag/PDA/MMS复合材料的制备及其催化性能

用双模板法制备了介孔纳米薄膜构筑的毫米级尺寸的大孔-介孔SiO₂(MMS)，通过多巴胺(DA)在其孔道表面氧化自聚合成聚多巴胺(PDA)，得到 PDA 修饰的 MMS(PDA/MMS)，再经 PDA 原位还原 Ag⁺制得大孔-介孔 Ag/PDA/MMS 复合材料。应用扫描电镜、透射电镜、N₂吸附-脱附、X射线光电子能谱、X射线衍射、UV-Vis、FT-IR和热重技术对所制得的材料进行表征。结果表明，MMS兼具纳米介孔材料和宏观尺寸大孔材料的优点。Ag/PDA/MMS在催化还原对硝基苯酚(4-NP)反应中展现出高催化活性，转化频率(TOF)达2.97 min^-1。这归因于其独特的结构：相互连通的大孔孔道大大降低了传质阻力，短孔道的介孔显著增加了活性位点的可达性，大的比表面积为反应物提供了大量的活性位点。而且，毫米级尺寸的Ag/PDA/MMS可以很容易从反应体系中分离出来，在5次循环后仍能将4-NP完全转化为对氨基苯酚(4-AP)。另外，Ag/PDA/MMS对亚甲基蓝(MB)的还原也有良好的催化效果。     

大孔-介孔Ag/PDA/MMS复合材料的制备及其催化性能

用双模板法制备了介孔纳米薄膜构筑的毫米级尺寸的大孔-介孔SiO₂(MMS),通过多巴胺(DA)在其孔道表面氧化自聚合成聚多巴胺(PDA),得到PDA修饰的MMS(PDA/MMS),再经PDA原位还原Ag+制得大孔-介孔Ag/PDA/MMS复合材料。应用扫描电镜、透射电镜、N2吸附-脱附、X射线光电子能谱、X射线衍射、UV-Vis、FT-IR和热重技术对所制得的材料进行表征。结果表明,MMS兼具纳米介孔材料和宏观尺寸大孔材料的优点。Ag/PDA/MMS在催化还原对硝基苯酚(4-NP)反应中展现出高催化活性,转化频率(TOF)达2.97 min^-1。这归因于其独特的结构：相互连通的大孔孔道大大降低了传质阻力,短孔道的介孔显著增加了活性位点的可达性,大的比表面积为反应物提供了大量的活性位点。而且,毫米级尺寸的Ag/PDA/MMS可以很容易从反应体系中分离出来,在5次循环后仍能将4-NP完全转化为对氨基苯酚(4-AP)。另外,Ag/PDA/MMS对亚甲基蓝(MB)的还原也有良好的催化效果。     

温敏性介孔复合材料PNIPAAm/SBA-15的制备与表征

采用自由基引发原位聚合(in situ polymerization)的方法合成了温敏性聚N-异丙基丙烯酰胺(PNIPAAm)/介孔分子筛SBA-15纳米复合物. 用FT-IR、XRD、TEM、低温N₂吸附-脱附、TG和DSC等手段对复合物进行了表征, 结果表明, 单体N-异丙基丙烯酰胺(NIPAAm)在介孔孔内发生了原位聚合, 聚合物PNIPAAm比较均匀地附于孔壁, 含量达24%左右. 这一聚合和孔内填充没有破坏SBA-15的有序六方结构, 但使样品的表面积、孔径、孔容减小. 同时, 这一有机-无机纳米复合物仍然保持PNIPAAm的温度响应性, 最低临界溶解温度(LCST)与纯PNIPAAm相似.     

Schiff碱改性法制备SBA-15型介孔分子筛负载的纳米氧化镍

基于Schiff碱功能单体的改性作用,采用共缩聚方法,制备了SBA-15型介孔分子筛负载的氧化镍纳米粒子。 采用小角X射线散射（small angle XRD）、广角X射线衍射（wide angle XRD）、紫外-可见光谱（UV-Vis）、高分辨透射电子显微镜（HRTEM）和N2吸附-脱附测定对制得的样品进行了表征。 结果表明,制得的样品具有SBA-15型介孔分子筛典型的二维六方有序结构,NiO纳米粒子主要分布于SBA-15型介孔分子筛的孔道内。 当功能单体的含量不超过10%时,SBA-15型介孔分子筛的孔径在6~8 nm范围内;而当功能单体的含量达到15%时,SBA-15型介孔分子筛的孔道被严重堵塞,孔径降为3.8 nm。 NiO纳米粒子的尺寸随着功能单体含量的增加而增大。     

C60/SBA-15介孔复合材料的合成及其荧光性质的研究

通过对介孔SBA-15孔壁氨基化(SBA-15-NH₂),然后与C₆₀反应形成化学键,成功地将C₆₀组装进入SBA-15孔道中,合成了C₆₀/SBA-15介孔复合材料.通过X射线衍射(XRD)、红外光谱(FTIR)、紫外-可见光谱(UV-V is)和差热-热重分析(TG-DTA)等方法对其进行了表征.同时,对复合材料的荧光性质进行了研究.结果发现,SBA-15-NH₂在575 nm处出现发射峰,C₆₀/SBA-15介孔复合材料在554 nm处出现发射峰,峰位蓝移21 nm.     

MgO/SBA-15固体碱介孔材料的研制

结合浸渍和微波辐射技术，分别采用浸渍、浸渍-微波、微波辐射等方法将醋酸镁高分散在SBA-15上而成为MgO改性介孔固体碱材料。结果显示：使用不同负载方法以及含铝SBA-15为载体，均能使MgO均匀分散;负载量达到20%时，XRD法仍未检测到样品上有MgO的晶相。实验表明负载的MgO在载体上形成了多层重叠结构，产生较多的中强碱位，而在介孔分子筛中引入Al原子则有利于碱位的形成。     

一种新的高活性CO氧化催化剂Ag/SBA-1

 以SBA-15为载体,采用后修饰法制备了Ag/SBA-15催化剂. XRD和TEM结果表明,金属Ag粒子均匀分散于SBA-15的纳米孔道中,粒子平均大小为4～5 nm. 同时,负载金属Ag纳米粒子后,载体的介孔结构仍然能很好地保持. CO催化氧化测试结果表明,Ag/SBA-15具有很高的催化活性,120 ℃时就能使CO完全氧化. 而在富H2气氛下,80 ℃时CO的转化率达到最大值(48%),此时O2的选择性为28%. 高温H2还原是活化Ag/SBA-15的必要步骤.     

(SBA-15)-ZnS主-客体纳米复合材料的制备与表征

本研究在SBA-15分子筛孔道中制备了纳米ZnS。Zn_{2+首先通过离子交换交换到SBA-15中,通过水热法在SBA-15分子筛孔道中制备了纳米ZnS。(SBA-15)-ZnS复合物由粉末X-线衍射,傅立叶变换红外光谱,低温氮气吸附-解析附技术,固体扩散漫反射光谱以及发光研究进行了表征。粉末X-线衍射研究说明在制备主-客体纳米复合材料中分子筛骨架未被制备过程所破坏,保持完整且结晶度仍很高。傅立叶变换红外光谱表明制备的材料骨架完好。77 K低温氮气吸附-解析附研究表明所制备的复合材料孔体积,孔尺寸以及表面积相对于SBA-15分子筛降低,证明客体ZnS已成功地组装入分子筛孔道中。所制备的纳米复合材料固体扩散漫反射吸收光谱相对于体相ZnS显示出蓝移表明,ZnS已限制在分子筛的孔道中且复合材料中分子筛的孔道对ZnS具有明显的立体限域效应,ZnS成功地组装在SBA-15分子筛的孔道中。发光研究表明,(SBA-15)-ZnS样品出现明显发光现象。主-客体复合材料具有良好的发光性能,有望在发光材料领域中获得应用。}     

Ag/SBA-15表面催化过程的现场SERS研究

以三嵌段共聚物P₁₂₃为模板剂, 正硅酸乙酯为硅源, 水热合成了介孔分子筛SBA-15, 通过对SBA-15内外表面修饰, 使用银氨溶液和硝酸银溶液作为金属源合成Ag/SBA-15, 透射电镜(TEM)研究表明在SBA-15孔道内较好地分散了颗粒状和棒状的Ag纳米粒子. 以苯硫酚作为探针分子, 研究了负载Ag纳米粒子的SBA-15的SERS效应, 结果表明Ag/SBA-15具有良好的SERS活性. 另外, 该材料对催化硼氢化钠还原对硝基苯酚具有良好的催化效果, 通过结合现场SERS技术, 研究了该催化过程的机理.     

Iron-modified mesoporous SBA-15 silica: Preparation and characterization studies

Fe-SBA-15 materials with different Si/Fe ratios (Si/Fe = 100, 60, 15) have been synthesized by hydrothermal method and characterized by several spectroscopic techniques. Electron spin resonance and Mössbauer spectroscopy, along with electron microscopy and X-ray diffraction, allowed differentiation of several iron species. These species correspond to hematite particles, very small “isolated” or oligomeric Fe^III species possibly incorporated in the mesoporous silica wall, and Fe^III oxide clusters either isolated or agglomerated, forming “rafts” at the surface of the silica and exhibiting ferromagnetic ordering. Because of their agglomeration, these clusters appear with a two-peak size distribution, with one peak corresponding to the isolated clusters formed in the mesopores and still embedded in them and the other corresponding to the agglomerates spread on the surface of the mesoporous silica particles.     

Bilirubin adsorption on amine/methyl bifunctionalized SBA-15 with platelet morphology

To remove bilirubin from human plasma, amine/methyl bifunctionalized SBA-15 materials were directly synthesized from the co-condensation of 3-aminopropylmethyldiethoxysilane and tetraethoxysilane with an amphiphilic block copolymer P123 as template. XRD, N(2) sorption analysis, FTIR and (29)Si MAS NMR were used to identify their well-ordered mesostructure and the grafting of amine and methyl groups on the surface of as-synthesized materials. Both SEM and TEM indicated that the bifunctionalized SBA-15 possessed platelet morphology. This might be attributed to the charge repulsion brought by protonated amine groups and the diminution of hydroxyl groups on the end of silicate-micelles, which passivated the end-to-end anchoring of silicate-micelles along the longitudinal axis. Such a material was investigated as the adsorbent for selective bilirubin removal from human plasma, which showed a high bilirubin clearance of 51.4% within 1.5 h with a little amount of albumin adsorption. The results of hemolysis assay suggested that the bifunctionalized SBA-15 caused serious hemolysis of red blood cells. However, in practical application, plasma separation technique could avoid direct contact between the adsorbent and red blood cells. The further hemeolysis assay proved that the plasma after contacting with the bifunctionalized SBA-15 could not lead to the hemolysis of red blood cells. Thus, the bifunctionalized SBA-15 is expected to be a potential candidate as a clinical hemoperfusion material.     

Au/SBA-15 的制备及其催化 CO 氧化反应性能

 以 SBA-15 为载体, 采用沉积沉淀法制备了纳米 Au 催化剂, 研究了不同预处理条件对 Au 在载体表面状态的影响, 考察了催化剂样品催化 CO 氧化性能. 以高分辨率透射电子显微镜、N2 吸附、X 射线衍射、紫外-可见漫反射吸收谱、X 射线光电子能谱和电感耦合等离子体发射光谱等手段对催化剂的结构和表面性质进行了表征. 结果表明, 经还原焙烧处理后的 Au/SBA-15 催化剂热稳定性较好, Au 在 SBA-15 孔道表面呈高分散状态, 样品在 CO 氧化反应中表现出优异的低温催化活性和高温稳定性, 同时具有优异的抗烧结性能和良好的循环稳定性.     

CO oxidation catalyzed by Ag/SBA-15 catalysts: Influence of the hydrothermal treatment

Four types of SBA-15 were prepared with different times and temperatures of treatment in order to obtain a range of micropore sizes. CO oxidation was used as a probe reaction in order to evaluate the nature of the active species when SBA-15s were doped with ca 10% Ag deposited from an AgNO₃ solution and calcined or reduced at 350 °C. The texture (TEM, nitrogen physisorption), structure (XRD) and reducibility (TPR) of the various catalysts (Ag/SBA-15) were studied and compared to those of a catalyst prepared by deposition of silver on fumed silica as a reference. These catalysts differ initially by the nature of silica and by pore sizes. In CO oxidation, pre-reduced catalysts are more active than pre-oxidised ones. This has to do with two phenomena, i.e. sintering, which produces large inactive silver particles, and formation of active silver species in the form of small Ag₂O particles.     

纳米Ag/CNTs复合材料的制备、表征及对环三亚甲基三硝胺热分解的影响

采用银镜法和水热法制备了两种纳米Ag/CNTs(碳纳米管)复合材料, 利用傅里叶变换红外(FTIR)光谱、粉末X射线衍射(XRD)、透射电子显微镜(TEM)、扫描电子显微镜及能量散射光谱仪(SEM-EDS)对复合物的物相、组成、形貌和结构进行分析表征, 并运用差示扫描量热法(DSC)研究了纳米Ag/CNTs 复合材料对环三亚甲基三硝胺(RDX)热分解特性的影响. 结果表明: 纳米Ag 以10-80 nm的不规则球形“粘附”于纳米CNTs 表面,分散较均匀, 水热法制得的复合物表面纳米Ag较大、且负载的Ag粒子较多; 纳米Ag/CNTs 复合材料的加入改变了RDX的热分解过程, 使原有占主导的液相分解变为二次的气相反应加剧, RDX主分解峰形发生了明显的改变; 纳米Ag/CNTs 复合材料对RDX热分解的催化主要表现为分解温度的降低.     

Surface functionalization of SBA-15 by the solvent-free method

A solvent-free technique was employed for fast modification of mesoporous materials. Copper, chromium and iron oxide species could be highly dispersed in SBA-15 by manually grinding the corresponding precursor salts and the host, followed by calcinations for the first time. This method is more effective to spontaneously disperse oxide species onto SBA-15 than impregnation, probably forming monolayer or submonolayer dispersion of salts or oxides. Besides, Cr(VI) species dominate in the mixing sample while Cr(III) species dominate in the impregnation one. In the temperature programmed surface reaction of nitrosamines, the sample prepared by solvent-free method showed a higher catalytic activity than the impregnation one.     

Mo-Ni2P/SBA-15催化剂的制备、表征及加氢脱硫催化性能

以介孔分子筛SBA-15 为载体, 通过分步浸渍硝酸镍、磷酸氢二铵、钼酸铵, 然后在H₂气流下程序升温还原(H₂-TPR), 制备了一系列不同Mo 含量的Mo-Ni₂P/SBA-15 催化剂. 采用X 射线衍射(XRD)、氮气吸脱附(BET)、透射电子显微镜(TEM)和X射线光电子能谱(XPS)对催化剂的结构进行了表征, 评价了催化剂对二苯并噻吩(DBT)的加氢脱硫(HDS)活性. 结果表明, Mo-Ni₂P/SBA-15 催化剂仍然保留有介孔结构, 催化剂的物相主要是Ni₂P. 催化剂表面的Ni 以Ni^δ+和Ni²⁺形式存在; P以P^δ-和P⁵⁺形式存在; Mo以Mo^δ+和Mo⁶⁺形式存在. Mo能促进催化性能的提高, 其中Mo含量为1% (w, 质量分数)的Mo-Ni₂P/SBA-15 催化剂具有最好的二苯并噻吩加氢脱硫催化活性, 在反应温度为380 ℃, 反应压力为3.0 MPa的条件下, 二苯并噻吩的转化率可达99.03%, 所有考察的Mo-Ni₂P/SBA-15都以直接加氢脱硫(DDS)途径为主.     

超声膜扩散法制备纳米银粒子

采用超声膜扩散(Ultrasound-assisted reaction method, UAMR)的方法, 以NaBH4还原溶液中的银离子, 在聚乙烯吡咯烷酮(PVP)为稳定剂的条件下, 制备出了平均粒度为4.7 nm的银纳米粒子. 与超声滴加法(Ultrasound-assisted dropping reaction method, UADR)相比, 超声膜扩散法制备出来的银纳米粒子的粒径小, 且尺寸分布较窄.     

12-Tungstophosphates I-mmobilized on Chemically Modified Mesoporous Silica SBA-15

A functionalized material. PW/SBA-15m, was prepared successfully in diluted H2SO4 aqueous solutions by immobilizing 12-tungstophosphates on chemically modified mesoporous silica SBA-15 and characterized by elemental analysis, FTIR, ^31p MAS NMR, XRD and TEM. The results indicate that the framework of SBA-15 and the Keggin structure of PW12O40^3- were retained, and that 23%-33% (mass fraction) of PW12O40^3- wasimmobilized; the PW12O40^3- anions were finely dispersed on the pore wall of SBA-15. Having been leached in ethanol at 60 ℃ for 7 h, the loss of PW12O40^3- anions was not found.