CF3SO3H Initiated Cationic Polymerization of Diisopropenylbenzenes in Macrobatch and Microflow Systems

CF₃SO₃H was found to serve as a more superior initiator for the polymerization of diisopropenylbenzenes than the conventionally used acids such as H₂SO₄. Much faster polymerization at lower temperatures seems to be ascribed to the higher acidity of CF₃SO₃H. The use of microflow systems was also found to be effective in increasing the indane unit content, especially for 1,4‐DPB. Fast mixing and uniformity of the temperature seem to be responsible. The thus‐obtained polymers of high indane unit content serve as useful materials having high thermal resistance and low dielectric constants.

     

Modulation of Electroosmotic Flow Using Polyelectrolyte Brushes: A Molecular Dynamics Study

Polyelectrolyte brushes grafted on a pair of parallel nanochannel walls can affect the electroosmotic flow (EOF) significantly. A molecular dynamics simulation method is used to investigate the relationship between charge distribution on polyelectrolyte brushes and EOF parameters such as flux, velocity, and density of particles. The EOF can be modulated by changing the step between two charged beads on the same chain, S_c, and the valence of a bead, N_c. Simulation results indicate that the flux increases as the total number of charges on the brushes increases. The decrease of S_c and N_c can lead to a maximum average velocity in the center region. The influence on density of particles is also analyzed.

     

New Star‐Shaped Metallo‐Polymeric Chromophores

The synthesis of new star‐shaped polymers, prepared by atom transfer radical polymerization of methyl methacrylate with tris(dialkylaminostyryl‐2,2′‐bipyridine) zinc(II) and iron(II) metalloinitiators, is reported. Their thermal and optical (absorption and emission) properties are discussed.

Structure of the star‐shaped polymers.     

Polymerizable Ionic Liquid Crystals

Polymerizable vinylimidazolium ionic liquids (ILs) that contain mesogenic coumarin and biphenyl units, respectively, have been synthesized. The N‐alkylation of N‐vinylimidazole with bromoalkylated mesogenic units 7‐(6‐bromohexyloxy)coumarin ( 1 ) and 4,4′‐bis(6‐bromohexyloxy)biphenyl ( 2 ) was then carried out. The thermal behavior of the obtained ILs 3 and 4 was investigated by differential scanning calorimetry and polarizing optical microscopy. These measurements showed that the attached mesogenic units induce the self‐assembly of ILs and, therefore, the occurrence of liquid crystalline phases. Subsequently, the ionic liquid crystals (ILCs) 3 and 4 were polymerized by a free‐radical mechanism.

     

A New Type of Thermoresponsive Copolymer with UCST‐Type Transitions in Water: Poly(N‐vinylimidazole‐co‐1‐vinyl‐2‐(hydroxymethyl)imidazole)

1‐Vinyl‐2‐(hydroxymethyl)imidazole ( 2 ) is synthesized by a procedure described in the literature. Corresponding copolymers with upper critical solution temperature (UCST)‐type transitions in water and high‐glass transition temperatures (T_g) are prepared by free radical copolymerization with N‐vinylimidazole ( 1 ). Depending on the copolymer composition, the cloud point can be varied between 19 and 41 °C. As the copolymer composition is identical with the monomer feed ratio, the cloud point can be easily tuned in the desired range. Furthermore, a distinctive pH‐dependence and salt effect can be observed.

     

Thermo‐Responsive Hydrogels with Nanodomains: Rapid Shrinking of a Nanogel‐Crosslinking Hydrogel of Poly(N‐isopropyl acrylamide)

Rapidly shrinking poly(N‐isopropyl acrylamide) (PNIPAM) hydrogels are prepared by crosslinking with self‐assembled nanogels that consist of cholesteryl‐ and methacryloyl‐substituted pullulan (CHPMA). The CHPMA nanogel (R_h = 26.4 nm) was used as a crosslinker for a hydrophilic nanodomain. Transmission electron microscopy images of the nanogel‐crosslinked PNIPAM hydrogel reveal a well‐defined nanoporous structure. The nanogel‐crosslinked PNIPAM hydrogel shows rapid shrinking based on its structure. The shrinking half‐time was ≈2 min, which is about 3 400 times faster than that of a PNIPAM hydrogel crosslinked by methylene(bisacrylamide).

     

Aqueous RAFT Polymerization of Acrylamide and N,N‐Dimethylacrylamide at Room Temperature

Summary: The first example of a room temperature reversible addition‐fragmentation chain transfer polymerization conducted directly in aqueous media is detailed. Under these conditions acrylamide and N,N‐dimethylacrylamide may be polymerized in a controlled fashion to near quantitative conversions employing a difunctional trithiocarbonate chain transfer agent (CTA). Hydrolysis studies conducted at pH 5.5 suggest that the CTA is stable up to approximately 50 °C.

     

Synthesis of Block Copolymers Modified with Phosphonate Ester Groups Using Nitroxide‐Mediated Radical Polymerization

Summary: Phosphonate groups were introduced into block copolymers of styrene derivatives either as single end‐groups or as small blocks using nitroxide‐mediated radical polymerization. In order to combine the hydrophobic and hydrophilic segments, block copolymers with N,N‐dimethyl acrylamide were synthesized. After hydrolysis to phosphonic acid groups, adsorption of the polymer onto metal oxides was possible.

Conversion of the phosphonate groups by transesterification with trimethylbromosilane (TMBS), followed by hydrolysis of the silylester group.     

Synthesis and Aggregation Behavior of Multi‐Responsive Double Hydrophilic ABC Miktoarm Star Terpolymer

We report the first example of the synthesis and the “schizophrenic” micellization behavior of a multi‐responsive double hydrophilic ABC miktoarm star terpolymer. A well‐defined miktoarm star terpolymer consisting of poly(ethylene glycol), poly(2‐(diethylamino)ethyl methacrylate), and poly(N‐isopropylacrylamide) arms, PEG(‐b‐PDEA)‐b‐PNIPAM, was synthesized via the combination of atom transfer radical polymerization (ATRP) and click reaction. Containing pH‐responsive PDEA and thermo‐responsive PNIPAM arms, this novel type of miktoarm star terpolymer molecularly dissolves in aqueous solution at acidic pH and room temperature, but supramolecularly self‐assembles into PDEA‐core micelles at alkaline pH and room temperature, and PNIPAM‐core micelles at acidic pH and elevated temperatures. Most importantly, both types of micellar aggregates possess well‐solvated hybrid coronas.

     

Nitroxide‐Mediated Radical Polymerization in Microemulsion

Nitroxide‐mediated polymerizations of styrene in microemulsion have been carried out at 125 °C using the cationic surfactant tetradecyltrimethylammonium bromide and the nitroxides 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy (TEMPO) and N‐tert‐butyl‐N‐[1‐diethylphosphono‐(2,2‐dimethylpropyl)] nitroxide (SG1). TEMPO‐mediated polymerizations were extremely slow, with large particles (d_n = 39–129 nm) and broad molecular weight distributions (MWDs). The origin of the broad MWDs was likely significant alkoxyamine decomposition and differing diffusion rates of monomer and low MW alkoxyamines (and nitroxide) between monomer‐swollen micelles and polymer particles. SG1‐mediated polymerizations proceeded at higher rates, resulting in nanoparticles (d_n = 21–37 nm) and lower than for TEMPO.

     

Are the Interactions between Recombinant Prion Proteins and Polymeric Surfaces Related to the Hydrophilic/Hydrophobic Balance?

New non‐fouling tubes are developed and their influence on the adhesion of neuroproteins is studied. Recombinant prion proteins are considered as a single component representative of hydrophobic proteins. Samples are stored for 24 h at 4 °C in tubes coated with two different coatings: poly(N‐isopropylacrylamide) as a hydrophilic surface and a plasma‐fluorinated coating as a hydrophobic one. The protein adhesion is monitored by ELISA tests, XPS and confocal microscopy. It appears that the highest recovery of recombinant prion protein in the liquid phase is obtained with the hydrophilic surface while the hydrophobic character of the storage tube induces an important amount of biological loss. However, the recovery is not complete even for tubes coated with poly(N‐isopropylacrylamide).

     

Synthesis of Ferrocene‐Branched Chitosan Derivatives: Redox Polysaccharides and their Application to Reagentless Enzyme‐Based Biosensors

Ferrocene‐branched chitosan derivatives (CHIT‐Fc) are synthesized by reductive N‐alkylation of chitosan with ferrocenecarboxaldehyde. The structures of the products are determined by ¹H NMR and FT‐IR spectra. CHIT‐Fc is used as a functionalized matrix to immobilize GOD on glassy carbon electrodes. Ferrocenyls in CHIT‐Fc exhibit an excellent redox activity and establish efficient electrical communication between GOD and the electrodes for the oxidation of glucose. The development of a reagentless glucose biosensor is described.

     

Tunable Smart Surface of Gold Nanoparticles Achieved by Light‐Controlled Molecular Recognition Effection

Thermosensitive poly(N‐isopropylacrylamide) (PNIPAm)‐coated gold nanoparticles (AuNPs) were prepared by self‐assembly of the azobenzene‐terminated PNIPAm on the surface of the α‐cyclodextrin (α‐CD)‐capped AuNPs via the host–guest molecular recognition between α‐CD and azobenzene. Reversible attachment–detachment of azobenzene‐terminated PNIPAm on the surface of α‐CD‐capped AuNPs was achieved when subjected to visible and UV light irradiation alternately, which endowed thermosensitive AuNPs with tunable smart properties.

     

Photomechanical Switching Behavior of Semi‐Interpenetrating Polymer Network Consisting of Azobenzene‐Carrying Crosslinked Poly(vinyl ether) and Polycarbonate

Summary: A novel semi‐interpenetrating polymer network (semi‐IPN) with photomechanical switching ability was developed by a cationic copolymerization of azobenzene‐containing vinyl ethers in a matrix of a linear polycarbonate (PC). The semi‐IPN film showed reversible deformation upon switching the UV irradiation on and off and responded with unprecedented rapidity. The photomechanical effect is attributed to a reversible change between the highly aggregated and dissociated states of the azobenzene groups.

The reversible UV response of the length of the semi‐IPN film at 25 °C.     

Morphology and Dielectric Property of Homogenous BaTiO3/PVDF Nanocomposites Prepared via the Natural Adsorption Action of Nanosized BaTiO3

Summary: The development of a novel technique for the preparation of homogeneous BaTiO₃/polyvinylidene fluoride (BT/PVDF) nanocomposites without obvious agglomeration of BaTiO₃ particles was reported in this communication. The morphology, structure, and frequency dependence of the dielectric properties of the nanocomposites were characterized. All results show that the dielectric properties of the nanocomposites in this study are desirable, and the process for preparing the nanocomposites has potential applications in the electronic industry.

TEM micrograph of dry BT/PVDF mixtures with nanosized BT particles.     

Palladium Aryl Sulfonate Phosphine Catalysts for the Copolymerization of Acrylates with Ethene

The reaction of 2‐[bis(2‐methoxy‐phenyl)phosphanyl]‐4‐methyl‐benzenesulfonic acid (a) and 2‐[bis(2′,6′‐dimethoxybiphenyl‐2‐yl)phosphanyl]benzenesulfonic acid (b) with dimethyl(N,N,N′,N′‐tetramethylethylenediamine)‐palladium(II) (PdMe₂(TMEDA)) leads to the formation of TMEDA bridged palladium based polymerization catalysts ( 1a and 1b ). Upon reaction with pyridine, two mononuclear catalysts are formed ( 2a and 2b ). These catalysts are able to homopolymerize ethylene and also copolymerize ethylene with acrylates or with norbornenes. With ligand b , high molecular weight polymers are formed in high yields, but higher comonomer incorporations are obtained with ligand a .

     

Local Viscosity in the Vicinity of a Wall Coated by Polymer Brush from Green–Kubo Relations

When fluids are confined in slit pores between parallel walls, their static structures and their dynamical properties exhibit inhomogeneity in the z‐direction perpendicular to the wall. Of particular interest are local bulk viscosity η_b(z) and shear viscosity η_s(z). Here, we discuss an algorithm to estimate these quantities from Green–Kubo relations using equilibrium molecular dynamics. As an application example, a polymer brush (macromolecules end‐grafted to a substrate at z = 0) interacting with a solvent formed from point‐like particles is given.

     

Optical Non‐Linearity from Montmorillonite Intercalated with a Chromophore‐Containing Dendritic Structure: A Self‐Assembly Approach

Chromophore‐containing dendritic structures (G1, G2) are utilized to intercalate layered silicates, which results in a large d‐spacing up to 126 Å. An exfoliated morphology is obtained by mixing the dendritic structure intercalated layered silicates with polyimide in N,N‐dimethylacetamide solution. The dendritic structures attached on the clay template would arrange in a non‐centrosymmetric manner. This self‐assembled arrangement brought about the electro‐optical coefficients of 5–6 pm · V⁻¹ for these relatively low chromophore‐containing organic/inorganic nanocomposites without resorting to poling. Excellent temporal stability (100 °C) is also achieved.