A New Strategy for the Synthesis of Polyaniline Nanostructures: From Nanofibers to Nanowires

A new approach for the synthesis of polyaniline (PANI) nanostructures under UV light illumination has been developed, which is the first report of a templateless chemical process for preparing pure PANI nanowires. The acceleration effect of photo‐assistance on the polymerization can promote the homogeneous nucleation and elongation of the nanofibers and nanowires, leading to easy preparation of tunable diameters of the nanowires and nanofibers of PANI.

     

Chemical Dual‐Responsive Wettability of Superhydrophobic PANI‐PAN Coaxial Nanofibers

PANI‐PAN coaxial nanofibers have been prepared by electro‐spinning during polymerization. The surface of the resulting nanofibers is superhydrophobic with a water contact angle up to 164.5°. Conductivity of the PANI‐PAN nanofibers is about 4.3 × 10⁻² S · cm⁻¹. The superhydrophobic nanofibers show a chemical dual‐responsive surface wettability, which can be easily triggered by changing pH value or redox properties of the solution. A reversible conversion between superhydrophobicity and superhydrophilicity can be performed in a short time. The strategy used here may provide an easy method to control the wettability of smart surfaces by using properties of low‐cost functional polymers.

     

Self‐Assembly of Polyaniline/Au Composites: From Nanotubes to Nanofibers

Summary: Polyaniline (PANI)/Au composite nanotubes and nanofibers are synthesized through a self‐assembly process in the presence of camphorsulfonic acid and hydrochloric acid, as dopants, respectively. The PANI/Au composites are characterized by FT‐IR, UV‐vis, and thermogravimetric analysis to verify the incorporation of the Au nanoparticles and determine the Au content. Structural characterization is performed using SEM, TEM and X‐ray diffraction. The presence of the Au nanoparticles results in an increased conductivity and improved crystallinity of the PANI. The self‐assembly method employed here is a simple and inexpensive route to synthesize multifunctional nanotubes and nanofibers and could be extended to prepare other inorganic nanoparticle/PANI composites.

TEM image of PANI/Au nanotubes.     

High Rate Silicification of Peptide‐Polymer Assemblies Toward Composite Nanotapes

Well‐defined silica composite nanofibers are generated in a silicification process of self‐assembled poly(ethylene oxide)‐peptide nanotapes. Inspired by biological silica morphogenesis processes the nanotapes exhibit strong binding capabilities for silicic acid. Thus, pre‐hydrolyzed tetramethoxysilane could be used as silica precursor. Very low concentrations (270 µM) and short contact times (10 s) are sufficient to form effectively integrated nano‐composite tapes.

     

Fabrication of Superhydrophobic and Superoleophilic Polystyrene Surfaces by a Facile One‐Step Method

A facile one‐step method has been developed to prepare both superhydrophobic and superoleophilic surfaces of polystyrene (PS) without any chemical modification. A rough film consisting of micro‐bead and nano‐fiber mixed structures is formed by spraying a PS solution onto a large area and any type of substrate. The mixed structures with such unique wettability properties can be used in oil/water separation and as oil sorbents.

     

A Template‐Free Method toward Urchin‐Like Polyaniline Microspheres

Urchin‐like PANI microspheres with an average diameter of 5–10 µm have been successfully prepared. Their surfaces consist of highly oriented nanofibers of ≈30 nm diameter and 1 µm length. The solvent composition plays an important role in the formation process of urchin‐like PANI microspheres. The structure of the products has been characterized by FT‐IR, UV‐vis, and XRD. To investigate the self‐assembly of urchin‐like PANI microspheres, the effect of polymerization time on the morphology of the products has been studied. The morphological evolution process indicates that the urchin‐like microspheres originate from the self‐assembly of nanoplates, which then grow into urchin‐like microstructures with nanofibers on the surface.

     

Evidence of Branching in Poly(butyl acrylate) Produced in Pulsed‐Laser Polymerization Experiments

Branched poly(butyl acrylate) was obtained from pulsed‐laser polymerizations carried out in bulk and in solution between −16 and 60 °C. The predominantly short branches are formed by backbiting. The Arrhenius temperature dependence of the backbiting rate is calculated, and the activation energy of this process was found to be remarkably higher than that of propagation. Branching thus increases with temperature leading to broader SEC traces and difficulties in the accurate determination of k_p.

Arrhenius plot of k_fp2 versus 1/T determined experimentally.     

Electronic Structure and Doping Behavior of PANI‐NSA Nanofibers Investigated by Resonance Raman Spectroscopy

Summary: Polyaniline nanofibers (from 93 to 220 nm) doped with β‐naphtalenesulfonic acid (PANI‐NSA) have been characterized. Nonhomogeneity in the thickness of fibers, as can be seen with scanning electron microscopy, is the reason for their instability under the HCl doping process. Resonance Raman spectral profiles of PANI‐NSA fibers suggest a lower protonation state than the emeraldine salt forms. Observation of Raman bands, which are a result of cross‐linking, confirms that one of the properties of the polymeric structure formed in micellar polymerization is the type of connection between chains.

     

Preparation of Nanostructured Polyaniline and its Super‐Amphiphilic Behavior

PANI nanofibers are prepared electrochemically by template‐free method on a stainless steel electrode. Both the hydrophilicity and the lipophilicity of the modified SS surface are enhanced by the nanostructured PANI, and a super‐amphiphilic surface is obtained in this way. The influence of polymerization conditions, such as polymerization potentials, polymerization time, the acidity, and the dopants on the super‐amphiphilic property, has been systematically investigated. In addition, the mechanisms of obtaining a super‐amphiphilic surface are briefly discussed.

     

Synthesis of trifluoromethyl‐1,2,4‐triazine‐ and trifluoromethylpyrimidine‐fused uracils

A variety of trifluoromethyl‐1,2,4‐triazine‐ and trifluoromethylpyrimidine‐fused uracils ( 9 ), ( 12 ), ( 15 ) and ( 18 ) were synthesized from trifluoroacetaldehyde ethyl hemiacetal or trifluoroacetic anhydride and corresponding uracil derivatives.     

Unprecedented Route to Ordered Polyaniline: Direct Synthesis of Highly Crystalline Fibrillar Films with Strong π‐π Stacking Alignment

Films of polyaniline (PANI) featuring about 80% crystallinity and characterised with strong π‐π stacking alignment parallel to the film surface have been obtained directly after the original synthesis upon simple drying of the aqueous PANI suspension. A strong anisotropy in the growth of the nano‐sized crystals produced during the synthesis results in the formation of micrometer‐length fibrils perpendicular to the film surface in the course of water evaporation. The regular intercalation of water molecules between the PANI chains seems to be crucial for their ordering throughout the synthesis and film formation.

     

Facile Synthesis of Polyaniline‐Polypyrrole Nanofibers for Application in Chemical Deposition of Metal Nanoparticles

Polyaniline‐polypyrrole (PANI‐PPy) nanofibers with high aspect ratios have been synthesized by a one‐step, surfactant‐assisted chemical oxidative polymerization from mixtures of aniline (An) and pyrrole (Py) monomers. PANI‐PPy nanofibers synthesized with an excess of either PANI or PPy show similar spectral (UV‐vis and FT‐IR) characteristics as the individual homopolymers, whereas nanofibers from an equimolar mixture of An and Py display unique spectral characteristics. PANI‐PPy nanofibers undergo a spontaneous redox reaction with metal ions to produce metal nanoparticles with various morphologies and/or sizes. These findings may open new opportunities for synthesizing functional polymer nanofibers and metal nanoparticles with controllable sizes and/or morphologies.

     

Stabilization of Polymer Bilayers by Introducing Crosslinking at the Interface

Summary: Bisphenol A solid epoxy serves as an effective reaction compatibilizer to the bisphenol A polycarbonate (PC)/PMMA bilayer systems. Addition of epoxy to the bottom PMMA layer can retard or even prevent the dewetting of PC films by introducing crosslinking between both components at the interface. This is the first investigation of polymer bilayers stabilized by chemical reactions.

AFM topographic image of a representative dewetting hole.     

Transparent and Conductive Polyethylene Oxide Film by the Introduction of Individualized Single‐Walled Carbon Nanotubes

It is demonstrated that an optically transparent and electrically conductive polyethylene oxide (PEO) film is fabricated by the introduction of individualized single‐walled carbon nanotubes (SWNTs). The incorporated SWNTs in the PEO film sustain their intrinsic electronic and optical properties and, in addition, the intrinsic properties of the polymer matrix are retained. The individualized SWNTs with smaller diameter provide high transmittance as well as good electrical conductivity in PEO films.

     

Enhancement of Electrochromic Contrast by Tethering Conjugated Polymer Chains onto Polyhedral Oligomeric Silsesquioxane Nanocages

Copolymerization of aniline with octa(aminophenyl) silsesquioxane (OAPS) was performed, which resulted in polyaniline‐tethered, polyhedral oligomeric silsesquioxane (POSS‐PANI), with star‐like molecular geometry. The spectro‐electrochemical studies show that the electrochromic contrast of POSS‐PANI is much higher than that of polyaniline (PANI). The great improvement can be attributed to the more accessible doping sites and the facile ion movement during the redox switching, brought by the loose packing of the PANI chains. This was evidenced by a drastic increase in ionic conductivity, a decrease in the electrical conductivity, and a decrease in the crystallinity and crystal size, with the increase of the OAPS concentration in the POSS‐PANI.

     

Anionic Polysaccharides as Templates for the Synthesis of Conducting Polyaniline and as Structural Matrix for Conducting Biocomposites

A green chemoenzymatic pathway for the synthesis of conducting polyaniline (PANI) composites is presented. Laccase‐catalyzed polymerization in combination with anionic polysaccharides is used to produce polysaccharide/PANI composites, which can be processed into flexible films or coated onto cellulose surfaces. Different polysaccharide templates are assessed, including κ‐carrageenan, native spruce O‐acetyl galactoglucomannan (GGM), and TEMPO‐oxidized cellulose and GGM. The resulted conducting biocomposites derived from natural materials provide a broad range of potential applications, such as in biosensors, electronic devices, and tissue engineering.

     

Biopolymers and biomaterials based on elastomeric proteins

Elastomeric proteins represent a very interesting subject of investigation, not only for their molecular mechanism(s) of elasticity, but also for their great potential as novel biomaterials. This review is intended to give an overview of the properties of the main elastic proteins, with particular focus on elastin and, at the same time, a report on the most recent acquisitions in the field of elastomeric biomaterials.

TEM image of poly(OrnGlyGlyOrnGly) after crosslinking reaction with GTA. The bar represents 100 nm.