It is demonstrated that an optically transparent and electrically conductive polyethylene oxide (PEO) film is fabricated by the introduction of individualized single‐walled carbon nanotubes (SWNTs). The incorporated SWNTs in the PEO film sustain their intrinsic electronic and optical properties and, in addition, the intrinsic properties of the polymer matrix are retained. The individualized SWNTs with smaller diameter provide high transmittance as well as good electrical conductivity in PEO films.
Regioregular poly(3‐hexylthiophene) has been successfully incorporated into a novel amphiphilic block copolymer. The amphiphilic nature of poly(3‐hexylthiophene)‐block‐poly(acrylic acid) has been investigated using spectroscopic methods and has yielded solvatochromic behavior in several solvents of varying polarity. Evidence suggests that a supramolecular, long range ordering of block copolymer occurs in polar solvents, resulting in the formation of aggregates. Despite relatively large amounts of non‐conductive blocks, the poly(3‐hexylthiophene) diblock copolymer yields a high conductivity of 1 S · cm−1, and atomic force microscopy shows the formation of a highly organized nanofibrilar morphology in the solid state.
Supramolecular self‐assembly of block copolymers in aqueous solution has received ever‐increasing interest over the past few decades due to diverse biological and technological applications in drug delivery, imaging, sensing and catalysis. In addition to relative block lengths, molecular weights and solution conditions, chain architectures of block copolymers can also dramatically affect their self‐assembling properties in selective solvents. This feature article mainly focuses on recent developments in the field of supramolecular self‐assembly of amphiphilic and double hydrophilic block copolymers (DHBCs) possessing nonlinear chain topologies, including miktoarm star polymers, dendritic–linear block copolymers, cyclic block copolymers and comb‐shaped copolymer brushes.
Summary: The relatively high degree of crystallinity of a new thermoplastic polyimide (PI) makes it a favorable matrix candidate for fiber reinforced composites. This advantage is the result of the ability of the matrix to recrystallize during the composite manufacturing process. In this study we examine the potential nucleating effect of carbon nanotubes on a thermoplastic PI. In addition to their inherent mechanical contribution, the carbon nanotubes help recover a significant proportion of the original crystallinity.
Scanning electron micrograph of the spherulitic structure of a recrystallized carbon nanotube/polyimide film. 相似文献
Water‐soluble single‐ and multi‐walled carbon nanotubes (CNTs) were prepared by grafting polyacrylamide chains from the graphitic surface via ceric ion‐induced redox radical polymerization. The reducing functionalities were covalently attached to the tubes by peroxide‐assisted radical reaction. The results showed that polymer chains were grafted onto CNTs by the redox process. The redox radical polymerization initiated by carbon nanotube‐bearing functionalities not only provides a powerful strategy for modifying the carbon nanostructures but also gives us the knowledge of their sidewall chemistry.
Summary: Polyaniline (PANI)/Au composite nanotubes and nanofibers are synthesized through a self‐assembly process in the presence of camphorsulfonic acid and hydrochloric acid, as dopants, respectively. The PANI/Au composites are characterized by FT‐IR, UV‐vis, and thermogravimetric analysis to verify the incorporation of the Au nanoparticles and determine the Au content. Structural characterization is performed using SEM, TEM and X‐ray diffraction. The presence of the Au nanoparticles results in an increased conductivity and improved crystallinity of the PANI. The self‐assembly method employed here is a simple and inexpensive route to synthesize multifunctional nanotubes and nanofibers and could be extended to prepare other inorganic nanoparticle/PANI composites.
A simple approach to improve the structural ordering in block copolymer/nanoparticle nanocomposites is presented. It is to blend a small molecular weight homopolymer with the composites, which can uniformly swell the preferred domain where the nanoparticles locate and increase the conformational entropy of the domain. Consequently, the interfaces between the block copolymer domains become smooth that improves the long range order in the nanocomposites. Furthermore, the uniform swelling of the preferred domain by the homopolymer will allow higher loading of nanoparticles without adversely affecting the long range order.
Magnetic nanomaterials have been studied in order to generate novel nanocomposites that display both the magnetic properties of the nanoparticles and the ability to self‐assemble of the amorphous block copolymer matrix. Towards this goal, iron oxide magnetic nanoparticles have been modified with PS brushes by ATRP in order to improve both the dispersion and the affinity of the nanoparticles with one of the blocks of a polystyrene‐block‐polybutadiene‐block‐polystyrene block copolymer. This method of preparation of nanocomposites opens new strategies for the generation of magnetic nanomaterials. The samples are characterized using DSC and atomic and magnetic force microscopies.
The shielding effect of nano TiO2 on collagen under UV radiation was investigated using UV spectrophotometry. The results indicate that the shielding of collagen under UV radiation in the presence of nano TiO2 is significant. For 2.5 wt.‐% of TiO2, there is a greater shielding effect of UV radiation than that for 0.5 wt.‐% of TiO2. In addition, this study gives hints that a novel tanning agent with a UV shielding function can be formulated by using nano TiO2.
UV absorption of collagen under UV radiation after adding 2.5 wt.‐% TiO2. 相似文献
Hydrogen‐bonded supramolecular copolymers were easily prepared by mixing cyclohexanetricarboxamides with three ( 1 ) and six ( 2 ) alkylsilyl groups, and supramolecular fibers were fabricated. When the composition of 1 and 2 was at or close to equimolarity, the supramolecular copolymer chain was found to have an alternating sequence. This was attributed to the fact that the steric factor of the alkylsilyl side chains effectively controls the unit sequence of the supramolecular polymer chain.
Hierarchical poly(3‐hexylthiophene)(P3HT)/carbon nanotube (CNT) supramolecular structures were fabricated through a bottom‐up CNT induced P3HT crystallization strategy. P3HT nanowires growing perpendicular from CNT surface have uniform width and height. The density and the length of these nanowires can be controlled by tuning the P3HT/CNT mass ratio. The quasi‐isothermal crystallization process monitored by in situ UV–Vis spectroscopy indicates that CNTs can greatly enhance the P3HT crystallization, and the P3HT nanowire formation follows first‐order kinetics. Such bottom‐up strategy provides a general approach to build 2D functional conductive supramolecular structures that will lead to numerous applications in nanoscale electronics.
Summary: Thermosensitive association of a diblock copolymer consisting of poly(3‐dimethyl(methacryloyloxyethyl) ammonium propane sulfonate) (PdMMAEAPS), as an upper critical solution temperature (UCST) block, and poly(N,N‐diethylacrylamide) (PdEA), as a lower critical solution temperature (LCST) block, has been investigated by using IR spectroscopy. The ν(CO) and ν(SO) bands of the PdMMAEAPS block and the amide I band of PdEA block critically changed at the UCST and LCST, respectively, indicating that the segmental interaction of each block is altered at each transition.
The double temperature responsiveness of a UCST block and LCST block containing diblock copolymer. Micelles form at temperatures both below the UCST and above the LCST of the blocks. 相似文献
We have used a combinatorial gradient technique to map precisely how the terrace structure and microdomain lattice alignment in a thin film of a sphere‐forming diblock copolymer are affected by both the thickness of the copolymer film and the height of a series of parallel step edges fabricated on the substrate. We find that for film thicknesses slightly incommensurate with integer numbers of sphere layers, the step edges act as nucleation sites for regions with one more or one fewer layers of spheres. We also find that for our system, the hexagonal lattice formed by a single layer of spheres on the low side of a step edge is aligned along the direction of the step edge only where the film on the high side is sufficiently thin to support only a wetting layer of copolymer material. This work will guide the tuning of film thickness and step height in future studies and applications of graphoepitaxy in block copolymer films.
We report a combined experimental and theoretical study of micellization of block copolymer with hydrophilic nonionic corona‐forming blocks and weak polyelectrolyte (wPE) core‐forming blocks with pH‐triggered solubility in aqueous solutions. We demonstrate that in addition to micelles with neutral cores, there exist two other types of micelles with PE‐ or ionomer‐like cores, in which monovalent counterions are released or condensed on core wPE block, respectively. The transition between the two types of micelles occurred upon changes in ionization of the PE core block and resulted in nonmonotonous changes of aggregation number as a function of pH. Such micelles with stimulus responsive cores represent promising nanocarriers for controlled delivery applications.
The self‐assembly of two types of linear ABA triblock copolymers confined in cylindrical nanopores is studied using simulated annealing. The effects of pore size and block copolymer chain architecture on morphology, chain conformations and bridging fraction are investigated. For the bulk cylinder‐forming copolymers, novel structures such as helices and stacked toroids form, which depend sensitively on the pore size. Several significant differences between the two types of copolymers are predicted and explained based on the differences in their chain conformations and chain architectures. A simple model is proposed to explain the mean square radius of gyration for the bridge and loop chains.
Novel wormlike nanostructures were self‐assembled in bulk films of a well defined diblock copolymer with azobenzene moieties, which was prepared by atom transfer radical polymerization (ATRP). For comparison, a homopolymer with almost the same repeat units of azobenzene as those in the copolymer was also prepared. They both had well defined structures and exhibited a smectic liquid crystalline phase. Upon annealing the copolymer films, poly(methyl methacrylate) formed a matrix with excellent optical properties, and the azobenzene segment in the minority phase self‐assembled into a wormlike mesogenic domain in the bulk films. Such block copolymer films exhibited stability and transparency by eliminating the scattering of visible light, indicating their potential application as photoresponsive functional materials. Although wormlike morphologies have been obtained in micelles from block copolymer solutions, to the best of our knowledge, such wormlike nanostructures have never been explored in bulk films.
The carbon nitride poly(triazine imide) with intercalated bromide ions is a layered, graphitic material of 2D covalently bonded molecular sheets with an exceptionally large gallery height of 3.52 Å due to the intercalated bromide anions. The material can be cleaved both mechanically and chemically into thin sheets and scrolls analogous to the carbon‐only systems graphite and graphene.
