Electrocatalytic oxidation of NADH at mesoporous carbon modified electrodes

The electrochemical oxidation of β-nicotinamine adenine dinucleotide (NADH) was investigated at a glassy carbon electrode modified with carbon mesoporous materials (CMM). Due to the large surface area and electro-catalytic properties of CMM, the overpotential of the electrodes toward the oxidation of NADH is decreased by 595 mV in aqueous solution at neutral pH. The anodic peak currents increase steadily with the concentration of NADH in the range from 2 µM to 1.1 mM, the detection limit being 1.0 µM at pH 7.2 and a potential of +0.3 V vs. SCE. The apparent Michaelis-Menten constant is ～21.5 μM. The results enable NADH to be sensed at a low potential and are promising with respect to the design of dehydrogenase-based amperometric biosensors.     

The anodic reactivity of 4,4′-dimethoxychalcone: a synthetic and mechanistic investigation

The anodic oxidation of the 4,4′-dimethoxychalcone (DMC) was investigated by different electrochemical methods at a platinum working electrode and in acetonitrile as a solvent. The DMC exhibited a single irreversible anodic peak around 1.6 V versus Ag/AgCl. On the time scale of cyclic voltammetry experiments, the highly reactive radical cation issued from the first electron transfer underwent a second order rate-limiting reaction. The potential imposed electrolyses of DMC led to the formation of a semi-conducting oligomer with 40 % yield. Using different physico-chemicals methods, the structural study confirmed the formation of an o-phenylenevinylene oligomer. The values of the corresponding optical and electrochemical band gaps were calculated to be 3.15 and 2.86 eV, respectively. Finally, a mechanism for the DMC electro-oligomerization was proposed on the basis of the obtained results.     

Direct electrochemical detection of bisphenol A at PEDOT-modified glassy carbon electrodes

The electrochemical behavior of bisphenol A (BPA) was studied on poly(3,4-ethylenedioxythiophene) (PEDOT)-modified glassy carbon electrodes by cyclic voltammetry. It was observed that BPA oxidation on PEDOT film produced a BPA polymer (pBPA) showing excellent redox activity with anodic and cathodic peaks at 0.15 and 0.01 V, respectively; the former being evaluated for BPA electrochemical sensing. The amount of deposited pBPA has been estimated by electrochemical and spectroscopic analysis by X-ray photoelectron spectroscopy. The effect of scan rate and pH on the oxidation of pBPA film has been studied. The oxidation current was found to vary linearly with BPA concentration in the range 90–410 μM, and a detection limit of 55 μM was evaluated. Results of BPA amperometric detection have also been collected by using a repetitive potential step program to give a linear response to BPA in the concentration range 40–410 μM with a detection limit of 22 μM and a sensitivity of 1.57 μAμM^?1?cm^?2. The developed sensor showed satisfactory reproducibility and anti-interference properties and was successfully applied to BPA determination in mineral water samples.     

Influence of KMnO4 oxidation on the electrochemical performance of pitch-based activated carbons

In this work, activated carbons (ACs) are obtained from petroleum pitch by the combination of a chemical treatment with different potassium permanganate (KMnO₄) amounts, i.e., 0, 0.5, 1.0, and 2.0 g, and a chemical activation with KOH at a constant KOH/pitch ratio of 3/1. The effects of the chemical activating agent on the surface morphology and porosity are evaluated with scanning electron microscopy and N₂ adsorption isotherms at 77 K, respectively. The specific surface area of the pitch-based ACs is increased with increasing the amount of KMnO₄ pre-treatment and showed the highest value of 2,334 m² g^?1 at 2 g of KMnO₄ amount. The electrochemical performance of AC electrodes is examined by cyclic voltammetry and galvanostatic charge/discharge characteristics in 6 M KOH electrolyte. Among the prepared ACs, 2.0 K-ACs possesses a specific capacitance as high as 237 F g^?1 and showed excellent electrochemical performance due to its suitable porous structure and low interface resistance.     

A study of the electrocatalytic oxidation of methanol on a nickel–salophen-modified glassy carbon electrode

Nickel–salophen-modified glassy carbon electrodes prepared by transferring one drop of Ni–salophen complex solution on the electrode surface. This modified electrode has been used for the electrocatalytic oxidation of methanol in alkaline solutions with various methods such as cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy. The electrooxidation was observed as large anodic peaks, and early stages of the cathodic direction of potential sweep around 20 mV vs. Ag|AgCl|KCl_sat. A mechanism based on the electrochemical generation of Ni (Ш) active sites and their subsequent consumptions by methanol have been discussed. EIS studies were employed to unveil the charge transfer rate as well as the electrical characteristics of the catalytic surface. For the electrochemical oxidation of methanol at 5.0 M concentration, charge transfer resistance of nearly 0.936 kΩ was obtained, while the resistance of the electrocatalyst layer was about 111.6 Ω.     

Unsupported palladium nanoparticles for ethanol cyclic voltammetric sensing in alkaline media

Carbon-supported palladium nanostructures have had a recent rise in their use for ethanol oxidation applications. In this work, we present the use of unsupported palladium nanoparticles (PdNPs), synthesized by sodium borohydride chemical reduction method, for ethanol electrochemical sensing. The unsupported PdNPs were studied for ethanol oxidation in alkaline media by cyclic voltammetry, and additionally were characterized using transmission electron microscopy, and x-ray photoelectron spectroscopy. The performance of unsupported PdNP-modified glassy carbon electrodes for the electrochemical ethanol oxidation in 1.0 M potassium hydroxide (KOH) solution was studied by cyclic voltammetry. These electrochemical results demonstrated that the unsupported PdNPs have very promising catalytic activity towards the oxidation of ethanol in alkaline media with good detection performance in the concentration range of 2304 to 288 ppm (i.e., 50.00 to 6.25 mM). The detection limit and linear correlation coefficient were 49.3 ppm (1.10 mM) and 0.9998, respectively. The unsupported PdNP-modified glassy carbon electrodes presented good cyclic voltammetric stability for ethanol sensing application in alkaline media.     

Interfacial and bulk processes during oxide growth on titanium in ethylene glycol-based electrolytes

Anodic oxidation has proven to be a promising route for the growth of self-ordering oxide nanotubes on Ti, the best results being obtained in ethylene glycol (EG)-based electrolytes with the addition of fluoride and small amounts of water. In the present paper, emphasis is put on the investigation of barrier film growth and dissolution on Ti in EG electrolytes with the addition of H₂O (0.3–2.4 M) and NH₄F (0.015–0.17 M) using electrochemical and surface analytical techniques. Steady-state current–potential curves and electrochemical impedance spectra as depending on potential (?0.1/5.0 V vs. AgCl/Ag), water and fluoride content have been registered. In addition, the chemical composition of the surface of the oxides obtained at 0.1 and 1.0 V has been estimated by X-ray photoelectron spectroscopy (XPS). XPS analysis revealed the presence of a non-stoichiometric oxide containing mainly Ti⁴⁺ and a certain amount of Ti³⁺, with a certain degree of hydroxylation. Estimates of the total thickness of the oxide from the XPS data using a dual layer model are also presented. A kinetic model of the process is advanced to quantitatively interpret the electrochemical and surface analytical results.     

Relationship between the reactions of hydrogen sorption/desorption and methanol oxidation on bifunctional Ni/Pd electrode in alkaline solution

The present paper is aimed at studying the influence of the hydrogen sorption/desorption process occurring on the layered nickel–palladium (Ni/Pd) electrode on the kinetics of the reaction of methanol oxidation in strong alkaline KOH solution. The electrodes were prepared by chemical deposition of a thin layer of porous palladium on a nickel foam support. A scanning electron microscope was used for studying the morphology of both the nickel support and the porous palladium layer. The mechanism of the anodic desorption of hydrogen changes depending on whether or not 6 M KOH electrolyte is admixed with methanol. It was shown that, in the first cycle of the cyclic voltammetry (CV) measurements, the anodic peak current and peak charge related to the oxidative desorption of hydrogen significantly decrease due to the presence of methanol in KOH. This effect is attributed to the obstacles in hydrogen sorption due to the formation of a passivating layer on the Pd surface composed of both adsorbed methanol molecules and the intermediate products involving adsorbed CO. On the other hand, hydrogen desorbing from Pd electrode exerts influence on the kinetics of the reaction of methanol oxidation. Ni/Pd electrode undergoes considerable reactivation due to the potentiostatic saturation with hydrogen at ?1.1 V, followed by the ease in hydrogen desorption. The CV measurements proved that, after such a treatment, the peak of hydrogen desorption partially overlaps the double peak of methanol oxidation and, in consequence, the rate of methanol oxidation is enhanced. The positive effect of hydrogen releasing from the electrode on the kinetics of the reaction of methanol oxidation is ascribed to the anti-poison behavior consisting in the reaction of hydrogen radicals with intermediates adsorbed on the Pd surface.     

Voltammetric determination of sorbite at a mechanically renewed copper electrode

Potentials and currents of D-sorbitol oxidation peaks as a function of polarization conditions for a copper electrode in situ renewed by mechanically cutting a 0.5-μm surface layer are studied by direct-current cyclic voltammetry. Oxidation peaks of sorbite emerge in cyclic voltammograms recorded in alkaline supporting electrolytes (0.05–0.10 M KOH and NaOH solutions) upon scanning the potential to the anodic region (E _p = 0.50–0.58 V) and in the reverse direction (E _p = 0.60–0.62 V). The shape and parameters of these peaks depend on the concentration of KOH, because of the different copper oxides involved in the oxidation of sorbite formed at the electrode surface. The regeneration of the electrode surface is the necessary condition for good reproducibility of the peak parameters. The signals obtained on the surface of the unrenewed electrodes are almost halved and less reproducible. The calibration graph of the current of the sorbite oxidation peak as a function of its concentration is linear in the range from 5 × 10⁻⁴ to 1 × 10⁻² M.     

Carbon aerogels with modified pore structures as electrode materials for supercapacitors

Carbon aerogels (CA) with uniform pore structures were prepared by the polycondensation of phloroglucinol, resorcinol, and formaldehyde, using carboxylated chitosan as a soft template. The CA were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, and surface area analysis. When carboxylated chitosan was added, the time for wet gel formation was reduced by 60%, and the CA showed a more uniform pore structures. The electrochemical performance of the CA was measured in a three-electrode electrochemical cell. The CA prepared with added carboxylated chitosan showed lower charge transfer resistance on the electrode surface, and the specific capacitances were also enhanced, showing a specific capacitance as high as 135 F/g at a resorcinol-to-carboxylated chitosan mass ratio of 250:1 at a current density of 0.5 A/g. This specific capacitance is much higher than that of the CA without carboxylated chitosan. The capacitance retention under increasing discharge current density was also enhanced by the addition of carboxylated chitosan. The electrochemical performance of the CA in different electrolytes (1 M LiOH, 1 M NaOH, 1 M KOH, 3 M KOH, 6 M KOH, and 9 M KOH) was investigated. The results show that the electrochemical performance in 6 M KOH was better than those in other electrolytes.     

Supercapacitive behaviors of the nitrogen-enriched activated mesocarbon microbead in aqueous electrolytes

The activated nitrogen-enriched novel carbons (a-NENCs) have been prepared by direct carbonization of polyaniline/activated mesocarbon microbead composites and further activated by 16 M?HNO₃. The electrochemical performances and supercapacitive behaviors of the a-NENCs in 6 M KOH, 1 M?H₂SO₄, and 0.5 M?K₂SO₄ solutions are evaluated by cyclic voltammetry, galvanostatic charge/discharge, electrochemical impedance spectroscopy, cyclic life, leakage current, and self-discharge measurements. The results demonstrate that the supercapacitors perform definitely supercapacitive behaviors; especially in 6 M KOH electrolyte, the supercapacitor represents much better electrochemical performance with more excellent reversibility, shorter relaxation time of 1.11 s, and nearly ideal polarizability. The maximum specific capacitance of the supercapacitors using a-NENCs as active electrode material is 85.1 F?g^?1 at a rate of 500 mA?g^?1 in 6 M?KOH. These outcomes indicate that the 6 M?KOH aqueous solution is a promising electrolyte for the supercapacitor with a-NENCs as electrode material.     

Photoelectrochemical sensing for hydroquinone based on gold nanoparticle-modified indium tin oxide glass electrode

Gold nanoparticles (GNPs) were deposited directly onto the surface of indium tin oxide (ITO) thin film-coated glass by electrochemical method. It was used as a photoanode in a photoelectrochemical (PEC) cell for sensitive detection of hydroquinone (HQ) at an applied bias potential of 0.15 V vs. saturated calomel electrode. This heterostructure showed dramatically enhanced PEC properties due to the introduction of the Au/ITO interface. Under the irradiation, the marked photocurrent response was observed at the GNPs/ITO photoelectrode compared with bare ITO electrode. The anodic photocurrent could be further largely enhanced by HQ. A new PEC strategy for sensitive detection of HQ at a relative low potential was developed. The linear range for HQ determination was 0.25 to 150 μM, with a detection limit of 0.1 μM. The sensitivity on the GNPs/ITO electrode at the irradiation was ~ 3.3 times higher than that in dark. These results demonstrate that the simple GNPs/ITO electrodes have great potential for PEC analysis application.     

Improved electrooxidation of phenol at exfoliated graphite electrodes

In the presented paper, we report on electrochemical oxidation of phenol occurring at exfoliated graphite (EG) in alkaline solution. The mechanism of the electrocatalytic reaction of phenol oxidation was modified on adding methanol to the phenol-containing electrolyte. Using the voltammetry method, the influence of methanol additive on cyclic behavior of EG electrode was examined. A particular attention has been paid to the first two cycles when an abrupt decrease in electrocatalytic activity of various electrode materials has been observed. The results obtained showed that in the presence of methanol EG, electrode preserves its electrocatalytic activity for a longer time of phenol oxidation. In the absence of methanol in a phenol/KOH electrolyte, the charge of phenol oxidation peaks decreases sharply on cycling, whereas in the presence of methanol, the observed drop is considerably inhibited. The anodic charge attained for the 15th cycle of phenol oxidation in methanol-admixed electrolyte is the same as that for the third cycle recorded in methanol-free electrolyte. The thermogravimetric analysis (TG), Fourier-transformed infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS) data showed that an improved electrocatalytic activity of EG can be accounted for by new chemical composition of oligomer film built on the EG surface with the participation of methanol and/or the products of its oxidation.Presented at the 4th Baltic Conference on Electrochemistry, Greifswald, March 13–16, 2005.     

EQCM Study of Ru and RuO2 Surface Electrochemistry

The present study represents comparative analysis of voltammetric and microgravimetric behavior of active ruthenium (Ru), electrochemically passivated ruthenium (Ru/RuO₂) and thermally formed RuO₂ electrodes in the solutions of 0.5 M H₂SO₄ and 0.1 M KOH. It has been found that cycling the potential of active Ru electrode within E ranges 0 V–0.8 V and 0 V–1.2 V in 0.5 M H₂SO₄ and 0.1 M KOH solutions, respectively, leads to continuous electrode mass increase, while mass changes observed in alkaline medium are considerably smaller than those in acidic one. Microgravimetric response of active Ru electrode in 0.5 M H₂SO₄ within 0.2 V–0.8 V has revealed reversible character of anodic and cathodic processes. The experimentally found anodic mass gain and cathodic mass loss within 0.2–0.8 V make 2.2–2.7 g F^?1, instead of 17 g F^?1, which is the theoretically predicted value for Ru(OH)₃ formation according to equation: Ru+3H₂O?Ru(OH)₃+3H⁺+3e^?. In the case of Ru/RuO₂ electrode relatively small changes in mass have been found to accompany the anodic and cathodic processes within E range between 0.4 V and 1.2 V in the solution of 0.5 M H₂SO₄. Meanwhile cycling the potential of thermally formed RuO₂ electrode under the same conditions has lead to continuous decrease in electrode mass, which has been attributed to irreversible dehydration of RuO₂ layer. On the basis of microgravimetric and voltammetric study as well as the coulometric analysis of the results conclusions are presented regarding the nature of surface processes taking place on Ru and RuO₂ electrodes.     

Simultaneous determination of dopamine, uric acid and ascorbic acid with LaFeO3 nanoparticles modified electrode

LaFeO₃ nanoparticles of approximately 22 nm in size were synthesized and characterized by XRD and TEM. A novel glassy carbon electrode modified with LaFeO₃ nanoparticles was constructed and characterized by electrochemical impedance spectroscopy and cyclic voltammetry. The modified electrode exhibited strong promoting effect and high stability toward the electrochemical oxidation of dopamine (DA), which gave reversible redox peaks with a formal potential of 0.145 V (vs. Ag/AgCl) in pH 7.0 phosphate buffer solution. The anodic peak current (measured by constant potential amperometry) increased linearly with the concentration of dopamine in the range from 1.5?×?10^?7 to 8.0?×?10^?4 M. The detection limit was 3.0?×?10^?8 M. The relative standard deviation of eight successive scans was 3.47% for 1.0?×?10^?6 M DA. The interference by ascorbic acid was eliminated efficiently. The method was used to determine DA in dopamine hydrochloride injections and showed excellent sensitivity and recovery.     

Graphene oxides/multi-walled carbon nanotubes hybrid-modified carbon electrodes for fast and sensitive voltammetric determination of the anticancer drug 5-fluorouracil in spiked human plasma samples

The electrochemical oxidation of anticancer drug 5-fluorouracil (5-FU) at graphene oxides (GOs)/carbon nanotubes (CNTs) nanohybrid-modified screen-printed carbon and glassy carbon electrodes was studied by voltammetric techniques. The modified electrodes showed better performance toward the electro-oxidation and determination of 5-FU compared to CNTs-modified or GOs-modified electrodes. The oxidation peak current obtained at about + 1.156 V (vs. Ag/AgCl) from square wave voltammetry was linearly dependent on the 5-FU concentration in the ranges of 0.05–5 and 5–1200 µM in phosphate buffer solution of pH 7.0. The developed method was applied successfully to the electrochemical sensing of 5-FU in human plasma samples at micro-molar concentration levels with satisfactory results. It is hopeful that the developed method in the future can be used for the simple and fast determination of 5-FU in clinical test and pharmacokinetics.     

Design of a new hypoxanthine biosensor: xanthine oxidase modified carbon film and multi-walled carbon nanotube/carbon film electrodes

A new and simple-to-prepare hypoxanthine biosensor has been developed using xanthine oxidase (XOD) immobilised on carbon electrode surfaces. XOD was immobilised by glutaraldehyde cross-linking on carbon film (CF) electrodes and on carbon nanotube (CNT) modified CF (CNT/CF). A comparison of the performance of the two configurations was carried out by the current response using amperometry at fixed potential; the best characteristics being exhibited by XOD/CNT/CF modified electrodes. The effects of electrolyte pH and applied potential were evaluated, and a proposal is made for the enzyme mechanism of action involving competition between regeneration of flavin adenine dinucleotide and reduction of hydrogen peroxide. Under optimised conditions, the determination of hypoxanthine was carried out at ?0.2 V vs. a saturated calomel electrode (SCE) with a detection limit of 0.75 μM on electrodes with CNT and at ?0.3 V vs. SCE with a detection limit of 0.77 μM on electrodes without CNT. The applicability of the biosensor was verified by performing an interference study, reproducibility and stability were investigated, and hypoxanthine was successfully determined in sardine and shrimp samples.     

The influence of fluoride on the physicochemical properties of anodic oxide films formed on titanium surfaces

The influence of fluoride (and its concentration) on the electrochemical and semiconducting properties of anodic oxide films formed on titanium surfaces was investigated by performing electrochemical measurements (potentiodynamic/pontiostatic polarization, open circuit potential (OCP), and capacitance measurements) for a titanium/oxide film/solution interface system in fluoride-containing 1.0 M HClO(4) solution. On the basis of the Mott-Schottky analysis, and with taking into account both the surface reactions (or, say, the specifically chemical adsorption) of fluoride ions at the oxide film surface and the migration/intercalation of fluoride ions into the oxide film, the changes in the electrochemical behavior of titanium measured in this work (e.g., the blocked anodic oxygen evolution, the increased anodic steady-state current density, the positively shifted flat band potential, and the positively shifted film breakdown potential) were interpreted by the changes in the surface and the bulk physicochemical properties (e.g., the surface charges, surface state density, doping concentration, and the interfacial potential drops) of the anodic films grown on titanium. The fluoride concentrations tested in this work can be divided into three groups according to their effect on the electrochemical behavior of the oxide films: < or =0.001 M, 0.001-0.01 M, and >0.01 M. By tracing the changes of the OCP of the passivated titanium in fluoride-containing solutions, the deleterious/depassive effect of fluoride ions on the titanium oxide films was examined and evaluated with the parameter of the film breakdown time. It was also shown that the films anodically formed on titanium at higher potentials (>2.5 V) exhibited significantly higher stability against the fluoride attack than that either formed at lower potentials (<2.5 V) or formed natively in the air.     

One-step synthesis of nitrogen-doped porous carbon for supercapacitors utilizing KNO<Subscript>3</Subscript> as an electrolyte

Nitrogen-doped porous carbons were prepared using a facile method, with low-biotechnology fulvic acid potassium salts as a precursor. The prepared carbons had a high surface area (1623 m² g^?1) and good electrochemical properties, making them suitable electrode materials for supercapacitors. Nitrogen-doped porous carbons were tested as an electrode in both 6 M KOH aqueous solution and different concentrations KNO₃ aqueous solution. The nitrogen-doped porous carbons with unique microstructure and nitrogen functionalities exhibited a capacitance of 235 F g^?1 in a 6 M KOH aqueous solution. Electrochemical investigation showed that the nitrogen-doped porous carbons exhibited a broad potential operational window in a 2.5 M KNO₃ aqueous solution. Furthermore, a high capacitance retention of 88.1 % was achieved even after 5000 cycles at 1.7 V. Potassium nitrate solutions in a wide range of concentrations were also proven to be promising electrolytes for electrochemical capacitors because they are cheap, noncorrosive, electrochemically stable, and compatible to diverse current collectors.     

Electrochemical sensor for estriol hormone detection in biological and environmental samples

A stable conducting film for sensing using reduced graphene oxide (RGO), gold nanoparticles (GNPs), and potato starch (PS) is proposed. The characterization of the nanomaterials was obtained by ultraviolet and visible spectroscopy, dynamic light scattering, zeta potential, Fourier transform infrared spectroscopy, atomic force microscopy, and cyclic voltammetry. The voltammetric behavior of the RGO-GNPs-PS/GCE electrodes was studied in the presence of estriol and the results showed a high anodic peak current at 0.64 V. Under optimal conditions, an analytical curve was obtained, in which the anodic peak estriol was linear in the range from 1.5 to 22 μmol L^?1, with a detection limit of 0.48 μmol L^?1. The modified electrodes were applied for determination of estriol in environmental and biological samples. The proposed electrode was used for estriol determination in water and urine samples, which presented a recovery range from 92.1 to 106%, showing that RGO-GNPs-PS/GCE is a viable alternative for the detection of estriol and can be attractive for several electrochemical applications.