Optical properties of thermally evaporated CdS thin films

CdS thin films of varying thicknesses were deposited on cleaned glass substrates at room temperature by thermal evaporation technique in a vacuum of about 2 x 10^‐5 torr. UV‐VIS spectra of the films were studied using the optical transmittance measurements which were taken in the spectral region from 300 nm to 1100 nm. The absorbance and reflectance spectra of the films in the UV‐VIS region were also studied. Optical constants such as optical band gap, extinction coefficient, refractive index, optical conductivity and complex dielectric constant were evaluated from these spectra. All the films were found to exhibit high transmittance (∼ 60 ‐ 93 %), low absorbance and low reflectance in the visible/near infrared region from ∼ 500 nm to 1100 nm. The optical band gap energy was found to be in the range 2.28 – 2.53 eV. All the films annealed at 300°C for 4 hours in vacuum (∼ 10^‐2 torr) showed a decrease in the optical transmittance with its absorption edge shifted towards the longer wavelength, leading to the result that the optical band gap decreases on annealing the films. Also, on annealing crystallinity of the films improves, resulting in decrease in the optical transmittance. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Nanocrystalline transparent SnO2‐ZnO films fabricated at lower substrate temperature using a low‐cost and simplified spray technique

Nanocrystalline and transparent conducting SnO₂‐ ZnO films were fabricated by employing an inexpensive, simplified spray technique using a perfume atomizer at relatively low substrate temperature (360±5 °C) compared with conventional spray method. The structural studies reveal that the SnO₂‐ZnO films are polycrystalline in nature with preferential orientation along the (101) plane. The dislocation density is very low (1.48×10¹⁵lines/m²), indicating the good crystallinity of the films. The crystallite size of the films was found to be in the range of 26–34 nm. The optical transmittance in the visible range and the optical band gap are 85% and 3.6 eV respectively. The sheet resistance increases from 8.74 kΩ/□ to 32.4 kΩ/□ as the zinc concentration increases from 0 to 40 at.%. The films were found to have desirable figure of merit (1.63×10^–2 (Ω/□)^–1), low temperature coefficient of resistance (–1.191/K) and good thermal stability. This simplified spray technique may be considered as a promising alternative to conventional spray for the massive production of economic SnO₂ ‐ ZnO films for solar cells, sensors and opto‐electronic applications. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Conversion of CuS thin films to structured nanosheet CuyS (1 < y ≦ 2) by vacuum annealing

In this study, large‐area and uniform thickness novel nano‐sheet structured CuS thin films on ITO glass have been prepared by the one‐step electrodeposition method from a dimethyl sulfoxide solution. Thin films of completely preserved nano‐sheet like morphology of Cu_yS (y = 1.75, 1.8, 1.95, and 2.0) are grown by vacuum annealing CuS thin films at 500 °C for different lengths of time. The 500 °C sample heated for 10 hours was nearly converted to single phase of Cu₂S with y ∼ 2. The optical direct band gaps of nano‐sheet Cu_yS thin films annealed at 500 °C of 2, 6, and 10 hours in vacuum were found to be 1.94, 1.68, and 1.44 eV, respectively.     

Comparison of tin‐doped indium oxide films fabricated by spray pyrolysis and magnetron sputtering

A comparison of the properties between Tin‐doped Indium Oxide (ITO) films fabricated by sputtering and spray pyrolysis is presented. This analysis shows that the ITO films fabricated by DC magnetron sputtering in pure argon gas requires of a subsequent annealing for the improvement of their structural, electrical and optical properties, when they are compared to films fabricated by single‐stage spray pyrolysis process that includes a new approach. The optimum annealing temperature for ITO films sputtered at room temperature lies in the 300‐350 °C range. Under such conditions, the ITO sputtered films are slightly more resistive than the resistivity (2 × 10^‐4 Ω‐cm) shown by films sprayed at 480 °C using a solution with a 5 % of tin to indium ratio, and almost four times the worst value of the combination of transparency and conductivity determined by the value of the figure of merit (FOM). The sprayed films have a high value of the FOM, 2.9×10^‐2 Ω^‐1, which is comparable with the best published results.     

Effect of annealing temperatures on properties of sol‐gel grown ZnO‐ZrO2 films

Mixed ZnO‐ZrO₂ films have been obtained by sol‐gel technology. By using spin coating method, the films were deposited on Si and glass substrates. The influence of thermal annealings (the temperatures vary from 400 °C to 750 °C) on their structural properties has been studied. The structural behavior has been investigated by the means of XRD and FTIR techniques. The results revealed no presence of mixed oxide phases, the detected crystal phases were related to the hexagonal ZnO and to crystalline ZrO₂. The sol‐gel ZnO‐ZrO₂ films showed polycrystalline structure with a certain degree of an amorphous fraction. The optical transmittance reached 91% and it diminished with increasing the annealing temperatures. The optical properties of the sol‐gel ZnO‐ZrO₂ films, deposited on glass substrates are excellent with high transparency and better then those of pure ZrO₂ films, obtained at similar technological conditions. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Properties of Sm‐doped CaNb2O6 thin films deposited by radio‐frequency magnetron sputtering

Sm‐doped CaNb₂O₆ (CaNb₂O₆:Sm) phosphor thin films were prepared by radio‐frequency magnetron sputtering on sapphire substrates. The thin films were grown at several growth temperatures and subsequently annealed at 800 °C in air. The crystallinity, surface morphology, optical transmittance, and photoluminescence of the thin films were investigated by X‐ray diffraction, scanning electron microscopy, ultraviolet‐visible spectrophotometry, and fluorescence spectrophotometry, respectively. All of the thin films showed a main red emission radiated by the transition from the ⁴G_5/2 excited state to the ⁶H_9/2 ground state of the Sm³⁺ ions and several weak bands under ultraviolet excitation with a 279 nm wavelength. The optimum growth temperature for depositing the high‐quality CaNb₂O₆:Sm thin films, which was determined from the luminescence intensity, was found to be 400 °C, where the thin film exhibited an orthorhombic structure with a thickness of 370 nm, an average grain size of 220 nm, a band gap energy of 3.99 eV, and an average optical transmittance of 85.9%. These results indicate that the growth temperature plays an important role in controlling the emission intensity and optical band gap energy of CaNb₂O₆:Sm thin films.     

Preparation and optical properties of AgGaS2 nanofilms

In this paper, AgGaS₂ nanofilms have been prepared by a two‐step process involving the successive ionic layer absorption and reaction (SILAR) and annealing method. Using AgNO₃, GaCl₃ and Na₂S₂O₃ as reaction sources, the mixture films were firstly deposited on quartz glass substrates at room temperature, and then annealed in Ar environment at 200–500 °C for 4 h, respectively. The effects of annealing temperature on structural and optical properties were investigated by XRD, UV‐Vis, EDS and photoluminescence (PL) spectra. It was revealed in XRD results that α‐Ag₉GaS₆ was contained in the samples annealed at 200 °C, and this phase was decreased with increase of the annealing temperatures. When the sample was annealed at above 400 °C, the chalcopyrite AgGaS₂ nanofilm was obtained. The preferred orientation was exhibited along the (112) plane. It was shown in atomic force microscopy (AFM) results that the grain sizes in AgGaS₂ nanofilms were 18‐24 nm and the thin films were smooth and strongly adherent to the substrates. When the annealing temperature was higher than 400 °C, it is an optimum condition to improve the structural and optical properties of the AgGaS₂ thin films. The room temperature PL spectra of AgGaS₂ nanofilms showed prominent band edge emission at 2.72 eV. Based on all results mentioned above, it can be concluded that the SILAR‐annealing method is preferable to preparing high‐quality AgGaS₂ nanofilms. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and optoelectrical properties of Ga‐doped ZnO semiconductor thin films grown by magnetron sputtering

Transparent conductive gallium‐doped zinc oxide (Ga‐doped ZnO) films were prepared on glass substrate by magnetron sputtering. The influence of substrate temperature on structural, optoelectrical and surface properties of the films were investigated by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), spectrophotometer, four‐point probe and goniometry, respectively. Experimental results show that all the films are found to be oriented along the c‐axis. The grain size and optical transmittance of the films increase with increasing substrate temperature. The average transmittance in the visible wavelength range is above 83% for all the samples. It is observed that the optoelectrical property is correlated with the film structure. The Ga‐doped ZnO film grown at the substrate temperature of 400 °C has the highest figure of merit of 1.25 × 10⁻² Ω⁻¹, the lowest resistivity of 1.56 × 10⁻³ Ω·cm and the highest surface energy of 32.3 mJ/m².     

Effect of substrate temperature on the properties of vacuum evaporated indium selenide thin films

Thin films of InSe were obtained by thermal evaporation techniques on glass substrates maintained at various temperatures (T_sb = 30°, 400°C). X‐ray diffraction analysis showed the occurrence of amorphous to polycrystalline transformation in the films deposited at higher substrate temperature (400°C). The polycrystalline films were found to have a hexagonal lattice. Compositions of these films have been characterized by EDAX and the surface analysis by scanning electron microscopy. Optical properties of the films, investigated by using spectrophotometer transmittance spectra in the wavelength range (300 – 1100 nm), were explained in terms of substrate temperatures. Films formed at room temperature showed an optical band gap (E_g^opt) 1.56 eV; where as the films formed at 400°C were found to have a E_g^opt of 1.92 eV. The increase in the value of E_g^opt with T_sb treatment is interpreted in terms of the density of states model as proposed by Mott and Davis. The analysis of current ‐Voltage characteristics, based on space charge limited currents (SCLC) measurements, confirms the exponential decrease of density of states from the conduction band edge towards the Fermi level for both the amorphous and polycrystalline films. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Characteristics of ITO films fabricated on glass substrates by high intensity pulsed ion beam method

Transparent conductive oxides such as indium tin oxide (ITO) are interesting materials due to their wide-band gaps, high visible light transmittance, high infrared reflectance, high electrical conductivity, hardness and chemical inertness. ITO films were fabricated on soda lime glass substrates by using high-intensity pulsed ion beam (HIPIB) technique. The as-deposited films comprised of partially crystallized In₂O₃ and after annealing at 500 °C for 1 h the film changed to polycrystalline phase. After annealing carrier concentration and Hall mobility increased while specific resistance and sheet resistance decreased quickly; and this trend was also observed when film thickness increased up to 300 nm for the post-annealed samples. Further increase in thickness of the film changed the electrical properties slightly. Atomic force microscopy (AFM) revealed that roughness decreased after 500 °C annealing for 1 h in air, except for the film of 65 nm thick. The thickness of the film which relates to the carrier concentration and mobility, degree of crystallization, size of the grain, and connections among grains in film are main factors to determine film’s electrical properties.     

Effects of CdCl2 treatment on properties of CdTe thin films grown by evaporation at low substrate temperatures

The structural, morphological and optical properties of vacuum‐evaporated CdTe thin films were investigated as a function of substrate temperature and post‐deposition annealing without and with CdCl₂/treatment at 400°C for 30 min. Diffraction patterns are almost the same exhibiting higher preferential orientation corresponding to (111) plane of the cubic phase. The intensity of the (111) peak increased with the CdCl₂/annealing treatment. The microstructure observed for all films following the CdCl₂/annealing treatment are granular, regardless of the as‐deposited microstructure. The grain sizes are increased after the CdCl₂/annealing treatment but now contain voids around the grain boundaries. The optical band gaps, E_g, were found to be 1.50, 1.50 and 1.48 eV for films deposited at 200 K and annealed without and with CdCl₂/treatment at 400°C for 30 min respectively. A progressive sharpening of the absorption edge upon heat treatment particularly for the CdCl₂/treated was observed. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural investigation and electronic band transitions of nanostructured TiO2 thin films

Titanium dioxide (TiO₂) thin film was deposited on n‐Si (100) substrate by reactive DC magnetron sputtering system at 250 °C temperature. The deposited film was thermally treated for 3 h in the range of 400‐1000 °C by conventional thermal annealing (CTA) in air atmosphere. The effects of the annealing temperature on the structural and morphological properties of the films were investigated by X‐ray diffraction (XRD) and atomic force microscopy (AFM), respectively. XRD measurements show that the rutile phase is the dominant crystalline phase for the film annealed at 800 °C. According to AFM results, the increased grain sizes indicate that the annealing improves the crystalline quality of the TiO₂ film. In addition, the formation of the interfacial SiO₂ layer between TiO₂ film and Si substrate was evaluated by the transmittance spectra obtained with FTIR spectrometer. The electronic band transitions of as‐deposited and annealed films were also studied by using photoluminescence (PL) spectroscopy at room temperature. The results show that the dislocation density and microstrain in the film were decreased by increasing annealing temperature for both anatase and rutile phases. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and optical properties of 6CaO·6SrO·7Al2O3 thin films derived by sol-gel dip coating process

The nanostructured 6CaO·6SrO·7Al₂O₃ (C6S6A7) thin films with cubic structure using calcium, strontium metals, aluminium isopropoxide and ethylene glycol monomethyl ether as stating materials has been fabricated via sol-gel route. Based on hydrolysis of Ca²⁺, Sr²⁺ and Al³⁺ in the sol-gel processing using ethylene glycol monomethyl ether as solvent have been employed as the precursor material. The films were coated on soda lime float glass by the dip coating technique and annealed at 450 °C in air atmosphere. The structure, morphology and composition of the films were investigated by Fourier transformed infrared spectroscopy, X-ray powder diffraction, scanning electron microscopy, atomic force microscopy and X-ray photoelectron spectroscopy indicating that the films were composed of C6S6A7 nanoparticles with cubic structure. The spectral transmittance of the films was measured in the wavelength range of 200-1100 nm using an UV-visible spectrometer. It has been found that the optical properties of the films significantly affected by precursor chemistry and annealing temperature due to the improvement of the crystallinity of the films with increasing annealing temperature and became stable when the annealing temperature is higher than 450 °C. The C6S6A7 films annealed at 450 °C had high transparency about 80% in wide visible range.     

Influence of substrate temperature on the structure of ZnO:Al thin films

ZnO: Al films were prepared using low cost spray pyrolysis technique. The dependence of the physical properties on the substrate temperature was studied. The best films obtained at 500°C substrate temperature with preferred [002] orientation. The sheet resistance decreases with increased substrate temperature, and values as low as R_sh = 207 Ω/cm² are reached for substrate temperature of 500°C. The optical transmittance of films increased by increasing the substrate temperature and received to 75% at 500°C. (© 2007 WILEY ‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Preparation of thick,crack-free germanosilicate glass films by polyvinylpyrrolidone and study of the UV-bleachable absorption band

With addition of polyvinylpyrrolidone (PVP) transparent, stable GeO₂–SiO₂ sols containing up to 60–80 mol% GeO₂ were synthesized using tetraethyl orthogermanate (TEOG) and tetraethylorthosilicate (TEOS) as precursors for germania and silica, respectively. It was shown by TEM analyses that the PVP can be absorbed onto the colloidal particles providing steric hindrance for the combination and aggregation of particles. These sols were observed showing rapid increase in viscosity within both the early period and the end period of sol aging time, but exhibiting a viscosity value of about 28 mPa s within the rest aging time (45–90 h) satisfying well the requirements for the deposition of thick films by cycles of dip-coating operation. It was determined by TG-DTA and SEM analyses that the densification of GeO₂–SiO₂ gel material with PVP was much more retarded than the gel without PVP resulting in crack-free germansilicate films with a thickness of 3 μm. The crystallization behavior of germansilicate films was enhanced with the increase of GeO₂ content but glass films with a composition of 60GeO₂ · 40SiO₂ was obtained by sintered at 700 °C for 1 h and annealed at 550 °C under a flowing H₂/N₂ atmosphere for 2 h. FT-IR analyse showed that the heat treatment at 700 °C for 60 min was effective to remove the organics and hydroxyl groups in the germansilicate film. An intense 5 eV absorption band was distinctly observed in films. The intensity of this absorption band was found to be effectively bleached by UV illumination. Weak photoluminescence emission bands which originated from the neutral oxygen di-vacancy (NODV) were detected near 375 and 276 nm. Therefore, the 5 eV absorption band observed in this work was mainly caused by the neutral oxygen monovacancy (NOMV). A saturated absorptivity change of the UV-bleachable band after prolonged illumination was found to be 256 cm⁻¹ for the 60GeO₂ · 40SiO₂ films implying the NOMV concentration in the films reached about 3.8 × 10¹⁸ cm⁻³.     

Growth and characterization of highly c‐axis textured SrTiO3 thin films directly grown on Si(001) substrates by ion beam sputter deposition

Highly c‐axis textured SrTiO₃ (STO) thin films have been directly grown on Si(001) substrates using ion beam sputter deposition technique without any buffer layer. The substrate temperature was varied, while other parameters were fixed in order to study effect of substrate temperature on morphology and texture evolution of STO films. X‐ray diffraction, pole figure analysis, atomic force microscope, and high‐resolution electron microscopy were used to characterize and confirm quality and texture of the STO films. The experimental results show that optimum substrate temperature to achieve highly c‐axis textured films is at 700 °C. The full width at half maximum (FWHM) of 002_STO was found to be 2° and fraction of (011) orientation was as low as 1%. The surface morphology was Volmer‐Weber growth mode with a small roughness ∼1 nm. The lowest leakage current density (5.8 μA/cm² at 2 V) and the highest dielectric constant (ε_STO ∼ 98) were found for highly c‐axis textured films grown at 700 °C. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Microstructural and optoelectrical properties of transparent conducting ZnO:Al thin films for organic solar cells

The Al‐doped zinc oxide (ZnO:Al) thin films were grown on glass substrates by the magnetron sputtering technique. The films were characterized with X‐ray diffractometer, four‐point probe and optical transmission spectroscopy, respectively. The dependence of microstructural, electrical and optical properties on deposition temperature was investigated. The results show that all the films have hexagonal wurtzite structure with highly c‐axis orientation. And the microstrural and optoelectrical properties of the films are observed to be subjected to the deposition temperature. The ZnO:Al film prepared at the deposition temperature of 650 K possesses the best optoelectrical properties, with the lowest electrical resistivity (6.1×10⁻⁴ Ω·cm), the highest average visible transmittance (85.3%) and the maximum figure of merit (0.41 Ω⁻¹). The optical energy gap of the films was estimated from Tauc's law and observed to be an increasing tendency with the increment of the deposition temperature. Furthermore, the refractive index of the films was determined by the optical characterization methods and the dispersion behavior was studied by the single electronic oscillator model.     

Spray deposition and characterization of undoped and In‐doped tin disulphide thin films

Undoped and Indium doped tin disulphide (SnS₂) thin films had been deposited onto glass substrates at T_s = 300 °C using spray pyrolysis technique under atmospheric pressure with stannous chloride, indium chloride and thiourea as precursors. The structural, optical and electrical properties of the deposited films were characterized. The XRD pattern revealed that the undoped and doped films had preferred orientation along (002) plane with hexagonal structure. FESEM micrographs had shown that morphologies of the films changed with indium doping. Optical constant such as refractive index (n), extinction coefficient (k), real and imaginary parts of dielectric constants were evaluated from transmittance and reflectance spectra in UV‐Visible spectroscopy. The optical absorption data were used to determine the band gap energy and it was found to be 2.75 eV for undoped and 2.50 eV for indium doped films respectively. The room temperature dark resistivity was found to be 4.545 × 10³ Ω‐cm and 5.406 × 10³ Ω‐cm for undoped and In‐doped films respectively.     

Growth of lead bromide polycrystalline films

Lead bromide polycrystalline films were grown by the physical vapor deposition method (PVD). Glass 1″x1″ in size, uncoated, and coated with Indium Tin Oxide (ITO), was used as substrate and rear contact. The starting material was evaporated at temperatures from 395°C to 530°C under high vacuum atmosphere (6 x 10^‐3 Pa) and during 8 days. The substrate temperature was prefixed from 190°C to 220°C. Film thickness yielded values from 40 to 90 μm. Optical microscopy and scanning electron microscopy (SEM) were performed on the films. Grain size resulted to be from 1.0 to 3.5 μm. SEM and X‐ray diffraction indicate that films grow with a preferred orientation with the (0 0 l) planes parallel to the substrate. The Texture Coefficient (TC) related to the plane (0 0 6) was 7.3. Resistivity values in the order of 10¹² Ωcm were obtained for the oriented samples, but a strong polarization indicates severe charge transport problems in the films. Film properties were correlated with the growth temperature and with previous results for films of other halides. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effects of annealing on structural,electrical and optical properties of AgGa(Se0.5S0.5)2 thin films deposited by using sintered stoichometric powder

The structural, electrical and optical properties of AgGa(Se_0.5S_0.5 )₂ thin films deposited by using the thermal evaporation method have been investigated as a function of annealing in the temperature range of 450–600 °C. X‐ray diffraction (XRD) analysis showed that the structural transformation from amorphous to polycrystalline structure started at 450 ^oC with mixed binary phases of Ga₂Se₃, Ga₂S₃, ternary phase of AgGaS₂ and single phase of S. The compositional analysis with the energy dispersive X‐ray analysis (EDXA) revealed that the as‐grown film has different elemental composition with the percentage values of Ag, Ga, Se and S being 5.58, 27.76, 13.84 and 52.82 % than the evaporation source powder, and the detailed information about the stoichometry and the segregation mechanisms of the constituent elements in the structure have been obtained. The optical band gap values as a function of annealing temperature were calculated as 2.68, 2.85, 2.82, 2.83, and 2.81 eV for as‐grown, annealed at 450, 500, 550, and 600 °C samples, respectively. It was determined that these changes in the band gap are related with the structural changes with annealing. The temperature dependent conductivity measurements were carried out in the temperature range of 250‐430 K for all samples. The room temperature resistivity value of as‐grown film was found to be 0.7x10⁸ (Ω‐cm) and reduced to 0.9x10⁷ (Ω‐cm) following to the annealing. From the variation of electrical conductivity as a function of the ambient temperature, the activation energies at specific temperature intervals for each sample were evaluated. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)