Use of micro‐Raman spectrometry coupled with scanning electron microscopy to determine the chemical form of uranium compounds in micrometer‐size particles

In the frame of nuclear safeguards, knowledge of the chemical form (stoichiometry) of the uranium compounds present in the micrometric particulate material sampled by wiping surfaces in an inspected nuclear facility may point out the industrial process implemented in the installation. Micro‐Raman spectroscopy (MRS) coupled with scanning electron microscopy (SEM) has been used for the first time to analyze micrometer‐size particles of various uranium oxides [UO₂, U₃O₈, UO₃, and UO₄ · 4(H₂O)] deposited on carbon disks. Uranium particles are detected by means of SEM, and Raman analysis is then directly carried out inside the SEM measurement chamber without moving the carbon disk from SEM to MRS. When particles are deposited on appropriate carbon disks (sticky carbon tapes), despite a loss of signal‐to‐noise ratio of about an order of magnitude with regard to the stand‐alone MRS, all uranium oxides are successfully identified in particles by in‐SEM Raman analysis, obtaining similar characteristic bands as the ones obtained with the stand‐alone MRS. Moreover, with the SEM–MRS coupling, particles as small as 1 µm can be analyzed, whereas, without the SEM–MRS coupling, only particles larger than ~5 µm are efficiently analyzed, after localization inside the SEM, transfer of the sample holder into the MRS, and relocation of the particles inside the MRS. Copyright © 2013 John Wiley & Sons, Ltd.     

New evidences of in situ laser irradiation effects on γ‐Fe2O3 nanoparticles: a Raman spectroscopic study

The nature of the physical mechanisms responsible for the structural modification of the γ‐Fe₂O₃ nanoparticles under laser irradiation has been investigated by Raman spectroscopy. In situ micro‐Raman measurements were carried out on as‐prepared γ‐Fe₂O₃ nanoparticles about 4 nm in size as a function of laser power and on annealed γ‐Fe₂O₃ particles. A baseline profile analysis clearly evidenced that the phase transition from maghemite into hematite is caused by local heating due to laser irradiation with an increase of grain size of nanoparticles. This increasing was clearly determined by X‐ray diffraction from 4 nm in nanoparticles up to more than 177 nm beyond 900 °C in a polycrystalline state. Copyright © 2010 John Wiley & Sons, Ltd.     

Identification of pigments from the Shrine of Kaiping Diaolou by micro‐Raman spectroscopy

Shrines (or altars) are constructed in China for worshiping ancestors, Bodhisattva, and God of Wealth. In this work, pigments from the shrine of Kaiping Diaolou tower were analyzed by micro‐Raman spectroscopy, in conjunction with other analytical methods including scanning electron microscopy (SEM) with energy dispersive X‐ray spectroscopy (EDX) and X‐ray fluorescence (XRF). Paintings of the shrine were composed of 2–3 pigment layers and the total thickness was determined as about 200–300 µm by optical microscopy and SEM, indicating the fine painting skills applied in the construction of the shrine. The green pigments on the surface layer of the green fragment were identified as a mixture of lead phthalocyanine (PbPc) and cornwallite (Cu₅(AsO₄)₂(OH)₄) by XRF and micro‐Raman spectroscopy with two different excitation wavelengths (488 and 785 nm). Underneath the green layer, red and yellow ochre were found. The pigments on the surface layer of red and blue fragments were identified as hematite (Fe₂O₃) and lazurite or synthetic ultramarine [(Na₈(Al₆Si₆O₂₄)S₃)], respectively. Finally, the pigments under the two surface layers were identified by EDX and micro‐Raman spectroscopy as chromium oxide (Cr₂O₃), gypsum (CaSO₄·2H₂O) and calcite (CaCO₃). Copyright © 2011 John Wiley & Sons, Ltd.     

μ‐Raman spectroscopy of prehistoric paintings from the Abrigo Remacha rock shelter (Villaseca,Segovia, Spain)

The composition of the materials present in prehistoric paintings discovered on the walls of the Abrigo Remacha rock shelter (Villaseca, Segovia, Spain) has been characterised by micro‐Raman spectroscopy. In addition, scanning electron microscopy and energy dispersive X‐ray microanalysis have been used as auxiliary techniques. The results show that haematite (α‐Fe₂O₃) is the main component of the red pigment. Amorphous carbon and paracoquimbite (Fe₂(SO₄)₃.9H₂O) have been detected in the bluish black pigment used in a significant bi‐colour pictograph. This is the first time that this mineral has been discovered in a prehistoric painting. Accretions of whewellite and weddellite form crusts covering most of the painting panel. Different carbonates are the main components of the rocky substrate. The detection of gypsum on the surface of the panel is associated to the flaking process that is affecting the painting panel. Copyright © 2013 John Wiley & Sons, Ltd.     

Highly Ligand‐Directed and Size‐Dependent Photothermal Properties of Magnetite Particles

The development of cancer photothermal therapies, many of which rely on photothermal agents, has received significant attention in recent years. In this work, various ligands‐stabilized magnetite (Fe₃O₄) particles are fabricated and utilized as a photothermal agents for in vivo tumor‐imaging‐guided photothermal therapy. Fe₃O₄ particles stabilized by macromolecular ligands as, e.g. polyethylene glycol (PEG), exhibit a superior and more stable photothermal effect compared to Fe₃O₄ particles stabilized by small molecules like citrate, due to their stronger ability of antioxidation. In addition, the photothermal effect of Fe₃O₄ particles is revealed to increase with size, which is attributed to the redshift of Vis‐NIR spectra. Fe₃O₄ particles injected intravenously into mice can be accumulated in the tumor by the application of an external magnetic field, as revealed by magnetic resonance imaging. In vivo photothermal therapy test of PEG‐stabilized Fe₃O₄ further achieves better tumor ablation effect. Overall, this study demonstrates efficient imaging‐guided photothermal therapy of cancer that is based on Fe₃O₄ particles of optimized size and with optimized ligands. It is expected that the ligand‐directed and size‐dependent photothermal effect will provide more approaches in the design of novel materials.     

Full Protection for Graphene‐Incorporated Micro‐/Nanocomposites Containing Ultra‐small Active Nanoparticles: the Best Li‐Storage Properties

In recent years, graphene‐incorporated micro‐/nanocomposites represent one of the hottest developing directions for the composite materials. However, a large number of active nanoparticles (NPs) are still in the unprotected state in most constructed graphene‐containing designs, which will seriously impair the effects of the graphene additives. Here, a fully protected Fe₃O₄‐based micro‐/nanocomposite (G/Fe₃O₄@C) is rationally developed by carbon‐boxing the common graphene/Fe₃O₄ microparticulates (G/Fe₃O₄). The processes and results of full protection are tracked in detail and characterized by X‐ray diffraction, X‐ray photoelectron spectroscopy, and nitrogen absorption–desorption isotherms, as well as scanning and transition electron microscopy. When used as the anode for lithium‐ion batteries, the fully protected G/Fe₃O₄@C exhibits the best lithium‐storage properties in terms of the highest rate capabilities and the longest cycle life compared to the common G/Fe₃O₄ composites and commercial Fe₃O₄ products. These much improved properties are mainly attributed to its novel structural features including complete protection of active Fe₃O₄ nanoparticles by the surface carbon box, a robust conductive network composed of nitrogen‐doped graphene nanosheets, ultra‐small Fe₃O₄ NPs of 4–5 nm, abundant mesopores to accommodate the volume variation during cycling, and micrometer‐sized secondary particles.     

Some forensic applications of a combined micro‐Raman and scanning electron microscopy system

The structural chemical analyser (SCA) is a novel accessory that allows the analytical advantages of Raman spectroscopy and scanning electron microscopy with energy dispersive x‐ray detection (SEM/EDX) to be realised in a single hybridised instrument. The combined Raman–SEM/EDX system permits in situ characterisation of a sample based on both its molecular and elemental makeup. This article demonstrates the potential of using the SCA for interrogating trace evidence for criminalistic purposes. Illustrative evidentiary examples (taken from our laboratory's archives) include the examination of a white paint fragment consisting of several layers of the same colour and a sample of explosive mixture recovered from a place of interest. The sensitive SEM imaging contrast mechanisms enabled the optically identical multiple layers of the white paint to be distinguished easily. The individual layers were then unambiguously analysed to establish their elemental profile (from energy dispersive x‐ray (EDX)) and this was cross‐referenced with the chemical information derived from in situ Raman measurements. X‐ray mapping was used as a fast and convenient way of characterising simultaneously multiple solids constituting the explosive mixture. Typical particles were targeted and analysed both by EDX and Raman spectroscopy revealing an unusual chlorate‐based energetic mixture that also contained 2, 4, 6‐trinitrotoluene (TNT) and 2, 4, 6‐trinitrophenylmethylnitramine (Tetryl). Copyright © 2009 John Wiley & Sons, Ltd.     

Multifunctional Plasmonic Co‐Doped Fe2O3@polydopamine‐Au for Adsorption,Photocatalysis, and SERS‐based Sensing

A new type of multifunctional plasmonic nanoparticles, cobalt‐doped Fe₂O₃@polydopamine‐Au (Co‐Fe₂O₃@PDA‐Au), is fabricated via coating PDA through self‐polymerization onto Co‐Fe₂O₃ and further loading gold nanoparticles by in situ reduction onto the surface of PDA shell. Benefiting from the universal adhesive ability of PDA and negative zeta potetntial of the composite, the Co‐Fe₂O₃@PDA‐Au shows strong adsorptivity for cationic dyes. The presence of gold nanoparticle with the diameter of 15 nm in the Co‐Fe₂O₃@PDA‐Au system promotes surface‐enhanced Raman scattering (SERS) activity with an impressive detection limit of 1 × 10^?6 m . Thanks to the synergistic effect of the light harvesting of PDA, the surface plasmon resonance of Au, and the electron conductibility of PDA and Au, the Co‐Fe₂O₃@PDA‐Au exhibits an enhanced photocatalytic activity comparing with unmodified Co‐Fe₂O₃. All the above‐mentioned functions enable Co‐Fe₂O₃@PDA‐Au to be a multifunctional material system for various applications toward environmental pollutants.     

Micro‐Raman investigation of transition‐metal‐doped ZnO nanoparticles

We measured the Raman spectra of ZnO nanoparticles (ZnO‐NPs), as well as transition‐metal‐doped (5% Mn(II), Fe(II) or Co(II)) ZnO nanoparticles, with an average size of 9 nm. A typical Raman peak at 436 cm⁻¹ is observed in the ZnO‐NPs, whereas Zn_1−xMn_xO, Zn_1−xFe_xO and Zn_1−xCo_xO presented characteristic peaks at 661, 665 and 675 cm⁻¹, respectively. These peaks can be related to the formation of Mn₃O₄, Fe₃O₄ and Co₃O₄ species in the doped ZnO‐NPs. Moreover, these samples were analyzed at various laser powers. Here, we observed new vibrational modes (512, 571 and 528 cm⁻¹), which are specific to Mn, Fe and Co dopants, respectively, and ZnO‐NPs did not reveal any additional modes. The new peaks were interpreted either as disorder activated phonon modes or as local vibrations of Mn‐, Fe‐ and Co‐related complexes in ZnO. Copyright © 2007 John Wiley & Sons, Ltd.     

Surface‐enhanced Raman scattering of 4‐mercaptopyridine on sub‐monolayers of α‐Fe2O3 nanocrystals (sphere,spindle, cube)

We report surface‐enhanced Raman scattering (SERS) spectra from 4‐mercaptopyridine (4‐Mpy) adsorbed on sub‐monolayers of α‐Fe₂O₃ nanocrystals (sphere, spindle, cube). The maximum enhancement factor has been estimated to be about 10⁴ compared to that of 4‐Mpy in solution. A possible mechanism has been proposed that the charge transfer between the α‐Fe₂O₃ nanocrystals and the 4‐Mpy molecules is most likely responsible for the observed enhancement of Raman intensity of adsorbed 4‐Mpy molecules as surface plasmon resonances have not occurred. Copyright © 2009 John Wiley & Sons, Ltd.     

Yolk–Shell‐Structured Cu/Fe@γ‐Fe2O3 Nanoparticles Loaded Graphitic Porous Carbon for the Oxygen Reduction Reaction

Core–shell Cu/γ‐Fe₂O₃@C and yolk–shell‐structured Cu/Fe@γ‐Fe₂O₃@C particles are prepared by a facile synthesis method using copper oxide as template particles, resorcinol‐formaldehyde as the carbon precursor, and iron nitrate solution as the iron source via pyrolysis. With increasing carbonization temperature and time, solid γ‐Fe₂O₃ cores are formed and then transformed into Fe@γ‐Fe₂O₃ yolk–shell‐structured particles via Ostwald ripening under nitrogen gas flow. The composition variations are studied, and the formation mechanism is proposed for the generation of the hollow and yolk–shell‐structured metal and metal oxides. Moreover, highly graphitic carbons can be obtained by etching the metal and metal oxide nanoparticles through an acid treatment. The electrocatalytic activity for oxygen reduction reaction is investigated on Cu/γ‐Fe₂O₃@C, Cu/Fe@γ‐Fe₂O₃@C, and graphitic carbons, indicating comparable or even superior performance to other Fe‐based nanocatalysts.     

Investigating the mechanisms of diamond polishing using Raman spectroscopy

Recent research has shown that a phase transformation of diamond to a different form of carbon is involved when diamonds are polished in the traditional fashion. The question as to how this phase transformation is activated and maintained to produce high wear rates is of great technological interest since it may radically change the way we view the processing of diamond. This paper describes the use of Raman spectroscopy to examine debris produced on the diamond polishing wheel, both during its preparation and during polishing. In addition, polished diamond surfaces were examined for the possible existence of non-diamond surface layers in an attempt to identify material removal mechanisms. Raman spectroscopy proves ideal for these analyses because its relatively high spatial resolution is well suited to the analysis of small wear features and debris particles, and because of the wealth of information it reveals about chemical structure. This level of structural information has been lacking in previous analyses of diamond polishing debris. In addition to the non-diamond carbon found in the wear debris, significant quantities of two iron oxides, magnetite (Fe₃O₄) and haematite (α-Fe₂O₃), were also found. An interesting observation was that a transformation from magnetite to haematite could be induced either by using high power laser excitation or by frictional heating during polishing. It is suggested that some of the Raman peaks previously attributed to lonsdaleite might better be explained by the presence of these oxides.     

The growth of the passive film on iron in 0.05 M NaOH studied in situ by Raman micro‐spectroscopy and electrochemical polarisation. Part I: near‐resonance enhancement of the Raman spectra of iron oxide and oxyhydroxide compounds

Raman spectroscopy, in principle, is an excellent technique for the study of molecular species developed on metal surfaces during electrochemical investigations. However, the use of the more common laser wavelengths such as the 514.5‐nm line results in spectra of less than optimal intensity, particularly for iron oxide compounds. In the present work, near‐resonance enhancement of the Raman spectra was investigated for the iron oxide and iron oxyhydroxide compounds previously reported to be present in the passive film on iron, using a tuneable dye laser producing excitation wavelengths between 560 and 637 nm. These compounds were hematite (α‐Fe₂O₃), maghemite (γ‐Fe₂O₃), magnetite (Fe₃O₄), goethite (α‐FeOOH), akaganeite (β‐FeOOH), lepidocrocite (γ‐FeOOH) and feroxyhyte (δ‐FeOOH). Optimum enhancement, when compared to that with the 514.5‐nm line, was obtained for all the iron oxide and oxyhydroxide standard samples in the low wavenumber region (<1000 cm⁻¹) using an excitation wavelength of 636.4 nm. Particularly significant enhancement was obtained for lepidocrocite, hematite and goethite. Copyright © 2010 John Wiley & Sons, Ltd.     

Fabrication of Au nanorod‐coated Fe3O4 microspheres as SERS substrate for pesticide analysis by near‐infrared excitation

Au nanorods coated Fe3O4 (Fe₃O₄@NRs) microspheres were designed as functional surface‐enhanced Raman scattering substrate with a feature of magnetic property and used for detection of pesticide residues that are annually used in agriculture by near‐infrared (NIR) excitation. With this strategy, the Fe₃O₄ microspheres were synthesized by hydrothermal method and surface functionalized with polyethylenimine, and then coated with Au nanorods densely. The Raman spectra were carried out by NIR excitation and 4‐ATP was chosen as the probe molecule. The results showed a good SERS activity of the Fe₃O₄@NRs microspheres. Moreover, this substrate could be used for pesticide analysis by portable Raman spectrometer with NIR excitation. Especially, the microspheres could be transferred from pesticides contaminated fruits peel to specially cleaned glass slide with the aid of the external magnetic field, by which the strong fluorescence of the apple components can be avoided while performing the pesticide analysis of fruits peel. Copyright © 2015 John Wiley & Sons, Ltd.     

Orthorhombic YAlO3 – a novel many‐phonon SRS‐active crystal

In single crystals of orthorhombic YAlO₃, widely known as a host‐matrix for Ln³⁺‐lasant ions, many‐phonon stimulated Raman scattering interactions as well as different manifestations of cascaded and cross‐cascaded nonlinear χ⁽³⁾↔χ⁽³⁾ processes are initiated by picosecond laser pulses. The scientific and applicative potential of YAlO₃ crystals is considerably expanded by the demonstration of its SRS properties. In particular, the studies revealed the manifestation of eight χ⁽³⁾‐active vibrational modes. The corresponding Stokes and anti‐Stokes lines have been assigned and the steady‐state Raman gain coefficients related to the strongest phonon mode have been estimated. In addition, a short review presents the stimulated emission channels of its Ln³⁺‐ions together with some χ⁽³⁾‐nonlinear laser properties of crystals belonging to the binary Y₂O₃‐Al₂O₃ system.     

Surface‐enhanced Raman scattering investigations on silver nanoparticles deposited on alumina and titania nanotubes: influence of the substrate material on surface‐enhanced Raman scattering activity of Ag nanoparticles

Silver nanoparticles deposited on various ‘inert’ porous materials (mainly Al₂O₃ and TiO₂) are often used as substrates for surface‐enhanced Raman scattering (SERS) measurements. In this study, we used the sputter deposition technique to cover tubular arrays of Al₂O₃ and TiO₂ with Ag nanoparticles. Raman spectra of pyridine (as a probe molecule) and of two selected dyes (5‐(4‐dimethylaminobenzylidene)rhodanine and 5‐(4‐(dimethylamino)benzylidene)‐3‐(3‐methoxypropyl)rhodanine) adsorbed on fabricated Ag/TiO₂‐n/Ti and Ag/Al₂O₃‐n/Al substrates were measured. We found that the SERS spectra of pyridine adsorbed on Ag nanoparticles deposited on an Al₂O₃‐n/Al substrate are distinctly different from those measured for an Ag/TiO₂‐n/Ti composite. Similar effects were observed for dyes adsorbed on the surface of both composites. The spectral differences between two kinds of composites (Ag/TiO₂‐n/Ti and Ag/Al₂O₃‐n/Al) are discussed in terms of (1) the modified electronic structure of the Ag nanoparticles due to their interaction with different substrate materials and (2) the different atomic topology of the metal particles thus deposited on the surfaces of the substrates. Composite samples were also studied with the aid of scanning electron microscopy (SEM) and Auger electron spectroscopy (AES) to reveal their characteristic morphological and chemical features. Copyright © 2012 John Wiley & Sons, Ltd.     

Surface functionalization, morphology and thermal properties of polyamide6/O-MMT composite nanofibers by Fe2O3 sputter coating

In the present work, the pure polyamide6 (PA6) nanofiber and PA6/organically modified montmorillonite (O-MMT) composite nanofiber were firstly prepared by a facile compounding process with electrospinning, and then coated by nanosize Fe₂O₃ using magnetron sputter technique. The effects of Fe₂O₃ sputter coating on structures, surface morphology and thermal stability were characterized by scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX), atomic force microscope (AFM) and thermogravimetric analyses (TGA), respectively. The SEM images showed that the diameters of composite nanofiber were decreased with the loadings of O-MMT and the nanosize Fe₂O₃ is well coated on the surface of the homogeneous and cylindrical nanofibers. The XPS spectra reflected the chemical features of the deposited nanostructures. The EDX confirmed the presence of the O-MMT and Fe₂O₃ in the fibers. The AFM observation revealed that there was a remarkable difference in the surface morphology of composite nanofiber before and after sputter coating. The TGA analysis indicated the barrier effects of silicate clay layers and catalysis effects of Fe₂O₃ improved thermal stability properties of the composite nanofiber.     

Facile Synthesis of Gd(OH)3‐Doped Fe3O4 Nanoparticles for Dual‐Mode T1‐ and T2‐Weighted Magnetic Resonance Imaging Applications

The facile hydrothermal synthesis of polyethyleneimine (PEI)‐coated iron oxide (Fe₃O₄) nanoparticles (NPs) doped with Gd(OH)₃ (Fe₃O₄‐Gd(OH)₃‐PEI NPs) for dual mode T₁‐ and T₂‐weighted magnetic resonance (MR) imaging applications is reported. In this approach, Fe₃O₄‐Gd(OH)₃‐PEI NPs are synthesized via a hydrothermal method in the presence of branched PEI and Gd(III) ions. The PEI coating onto the particle surfaces enables further modification of poly(ethylene glycol) (PEG) in order to render the particles with good water dispersibility and improved biocompatibility. The formed Fe₃O₄‐Gd(OH)₃‐PEI‐PEG NPs have a Gd/Fe molar ratio of 0.25:1 and a mean particle size of 14.4 nm and display a relatively high r₂ (151.37 × 10^?3m ^?1 s^?1) and r₁ (5.63 × 10^?3m ^?1 s^?1) relaxivity, affording their uses as a unique contrast agent for T₁‐ and T₂‐weighted MR imaging of rat livers after mesenteric vein injection of the particles and the mouse liver after intravenous injection of the particles, respectively. The developed Fe₃O₄‐Gd(OH)₃‐PEI‐PEG NPs may hold great promise to be used as a contrast agent for dual mode T₁‐ and T₂‐weighted self‐confirmation MR imaging of different biological systems.     

Characterization of laser processing of single‐crystal natural diamonds using micro‐Raman spectroscopic investigations

The application of lasers for processing diamond has revolutionized the diamond industry and its applications in microelectronics, microelectromechanical system (MEMS) and microoptoelectromechanical system (MOEMS) technologies. The process quality can be evaluated using spectroscopic techniques. In the present investigation, four different types of Q‐switched solid‐state lasers (with different beam parameters), namely, a lamp‐pumped Nd:YAG laser operating at 1064 nm, a lamp‐pumped Nd:YAG laser operating at second harmonically generated 532 nm, a diode‐pumped Nd:YVO₄ laser operating at 1064 nm and a diode‐pumped Nd:YAG laser operating at 1064 nm, have been employed for the processing of a single‐crystal, gem‐quality, natural diamond. The main objective behind the selection of these lasers with different beam parameters was to study the effect of wavelength, pulse width, pulse energy, peak power and beam quality factor (M² factor) on various aspects of processing (such as microcracking, material loss and cut surface quality) and their relative merits and demerits. The overall weight loss of the diamond and formation of microcracks during processing have been studied for the above four cases. The characteristics of the graphite formed during processing, elemental analysis, surface morphology of the cut surface and process dynamics have been studied using micro‐Raman spectroscopy and scanning electron microscopy (SEM). We observed that laser cutting of single‐crystal diamonds used for industrial applications can be accomplished without microcracking or surface distortion using Q‐switched Nd:YAG lasers. This allows direct processing without extensive postgrinding and polishing stages. Very efficient diamond processing is possible using diode‐pumped lasers, which results in the lowest possible breakage rate, good accuracy, good surface finish and low weight loss. From the micro‐Raman and SEM studies, it is concluded that the surface quality obtained is superior when diode‐pumped Nd:YVO₄ laser is used, owing to its extremely high peak power. The maximum graphite content is observed while processing with lamp‐pumped Nd:YAG laser at 532 nm. An overall comparison of all the laser sources leads to the conclusion that diode‐pumped Nd:YAG laser is a superior option for the efficient processing of natural diamond crystals. Copyright © 2006 John Wiley & Sons, Ltd.     

Single‐beam coherent anti‐Stokes Raman scattering (CARS) spectroscopy of gas‐phase CO2 via phase and polarization shaping of a broadband continuum

Coherent anti‐Stokes Raman scattering (CARS) spectroscopy of gas‐phase CO₂ is demonstrated using a single femtosecond (fs) laser beam. A shaped ultrashort laser pulse with a transform‐limited temporal width of ∼7 fs and spectral bandwidth of ∼225 nm (∼3500 cm⁻¹) is employed for simultaneous excitation of the CO₂ Fermi dyads at ∼1285 and ∼1388 cm⁻¹. CARS signal intensities for the two Raman transitions and their ratio as a function of pressure are presented. The signal‐to‐noise ratio of the single beam–generated CO₂ CARS signal is sufficient to perform concentration measurements at a rate of 1 kHz. The implications of these experiments for measuring CO₂ concentrations and rapid pressure fluctuations in hypersonic and detonation‐based chemically reacting flows are also discussed. Copyright © 2010 John Wiley & Sons, Ltd.