Synthesis of ZnSn(OH)6 regular octahedrons by a simple hydrothermal process

ZnSn(OH)₆ regular octahedrons were successfully synthesized through a simple hydrothermal method using an aqueous solution containing ZnO flower‐like structures, SnCl₄·5H₂O, and NaOH. Phase structure, morphology and microstructure of the samples were investigated by X‐ray diffraction (XRD) and scanning electron microscopy (SEM). Parameters in preparation process such as the ratios of Sn⁴⁺/OH^‐, the molar ratio of Zn/Sn and reaction time were discussed. Results show that the obtained samples are comprised of ZnSn(OH)₆ regular octahedrons with about 2 μm in side length and ZnSn(OH)₆ urchins‐like structures. ZnSn(OH)₆ urchins‐like structures preferentially grow on the edges and corners of regular octahedrons. Morphology of the products is susceptible to the ratios of Sn⁴⁺/OH^‐. A relatively low concentration of OH^‐ is favored to obtain ZnSn(OH)₆ regular octahedrons with urchins‐like structures on the surface, while a high concentration of OH^‐ results in a handful of regular octahedrons without urchins‐like structures on the surface. When the molar ratio of Zn/Sn changes to 1:2 or 2:1, the edges and corners of regular octahedrons become coarse and urchins‐like structures disappear from the surface. More urchins‐like structures form on the surface of regular octahedrons and the edges and corners of regular octahedrons become coarsened with the increase of reaction time. Moreover, the possible mechanism for ZnSn(OH)₆ regular octahedrons is discussed. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and characterization of carbon‐doped ZnSn(OH)6 with enhanced photoactivity by hydrothermal method

Well‐dispersed carbon‐doped ZnSn(OH)₆ submicrocubes were successfully synthesized through a facile and economical hydrothermal method at 433K, which used green chemical glucose (C₆H₁₂O₆) as the carbon‐doping source. Photocatalytic activity of the as‐synthesized C‐doped ZnSn(OH)₆ was evaluated by studying photocatalytic decomposition of methylene blue (MB) in aqueous solution under visible light irradiation(≥ 400 nm). The results show that carbon‐doped ZnSn(OH)₆ photocatalysts exhibited higher photocatalytic performance as compared to pure ZnSn(OH)₆. 1.0 wt% C‐doped ZnSn(OH)₆ photocatalyst exhibited obviously higher photocatalytic activity that of pure ZnSn(OH)₆ or other C‐ZnSn(OH)₆ catalysts under the same condition. The enhanced photocatalytic degradation of MB could be attributed to the doping of carbon and the possible mechanism for high photocatalytic activity of C‐doped ZnSn(OH)₆ was discussed.     

ZnSn(OH)6/SrSn(OH)6光催化降解甲苯的性能研究

采用简单的共沉淀法制备了新型ZnSn(OH)₆/SrSn(OH)₆复合光催化剂。利用X射线衍射(XRD)、X射线光电子能谱(XPS)、紫外可见-漫反射吸收光谱(UV-Vis)、N₂吸附脱附、扫描电镜(SEM)、透射电镜(TEM)对样品的结构、形貌和光吸收性质进行了表征,并以甲苯为目标污染物对其光催化性能进行评价。结果表明,与纯相SrSn(OH)₆和ZnSn(OH)₆相比,复合材料ZnSn(OH)₆/SrSn(OH)₆的紫外光吸收能力显著增强,光生载流子的复合效率降低,进而增强了其光催化降解甲苯的效率。复合样品ZSH/SSH-10摩尔比为10%对甲苯的降解率达到58%,是SrSn(OH)₆单体的1.35倍。循环使用5次后,ZSH/SSH-10的降解率仍保持51%以上,说明该催化剂具有良好的循环稳定性。     

Sonochemical synthesis and characterization of ZnO nanorod/Ag nanoparticle composites

A simple sonochemical route for the synthesis of Ag nanoparticles on ZnO nanorods is reported. Ultrasonic irradiation of a mixture of ZnO nanorods, Ag(NH₃)₂⁺, and formaldehyde in an aqueous medium yields ZnO nanorod/Ag nanoparticle composites. The powder X‐ray diffraction of the ZnO/Ag composites shows additional diffraction peaks corresponding to the face‐center‐cubic structured Ag crystalline, apart from the signals from the ZnO nanorods. Scanning electron microscopy and transmission electron microscopy images of the ZnO/Ag composites reveal that the ZnO nanorods are coated with Ag nanoparticles with a mean size of several tens nanometer. The absorption band of ZnO/Ag composites is distinctly broadened and red‐shifted, indicating the strong interfacial interaction between ZnO nanorods and Ag nanoparticles. This sonochemical method is simple, mild and readily scaled up, affording a simple way for synthesis of other composites. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

A ZnO/TiO2 composite nanorods photoanode with improved performance for dye‐sensitized solar cells

A dye‐sensitized solar cell (DSSC) based on ZnO/TiO₂ composite nanorods (NRs) photoanode is fabricated. The power conversion efficiency (PCE) of the ZnO/TiO₂ composite NRs film DSSC is 4.36%, which is obviously higher than that of DSSCs based on pure TiO₂ NRs (0.6%) and ZnO NRs (3.10%). The enhanced performance of ZnO/TiO₂ composite NRs film DSSC can be attributed to the combined effects of ZnO and TiO₂ NRs. In this architecture, the thick ZnO NRs overlayer offers a large surface area for enough dye absorption, while the thin TiO₂ NRs underlayer not only offers a direct and quick pathway for photoinjected electron transfer along the photoanode but also acts as a blocking layer, which effectively hinders the direct contact between the substrate and the electrolyte resulting in lower carrier recombination.     

Enhancement of the emission from TeO2 nanorods by encapsulation with ZnO

TeO₂‐core/ZnO‐shell nanorods were synthesized by a two–step process comprising thermal evaporation of Te powders and atomic layer deposition of ZnO. Scanning electron microscopy images exhibit that the core‐shell nanorods are 50 ‐ 150 nm in diameter and up to a few tens of micrometers in length, respectively. Transmission electron microscopy and X‐ray diffraction analysis revealed that the cores and shells of the core‐shell nanorods were polycrystalline simple tetragonal TeO₂ and amorphous ZnO with ZnO nanocrystallites locally, respectively. Photoluminescence measurement revealed that the TeO₂ nanorods had a weak broad violet band at approximately 430 nm. The emission band was shifted to a yellowish green region (∼540 nm) by encapsulation of the nanorods with a ZnO thin film and the yellowish green emission from the TeO₂‐core/ZnO‐shell nanorods was enhanced significantly in intensity by increasing the shell layer thickness. The highest emission was obtained for 125 ALD cycles (ZnO coating layer thickness: ∼15 nm) and its intensity was much higher than that of the emission from the uncapsulated TeO₂ nanorods. The origin of the enhancement of the emission by the encapsulation is discussed in detail. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and optical properties of ZnO nanorods

ZnO nanorods were prepared on the silicon (100) substrates using the chemical solution deposition method (CBD) without catalyst under a low temperature (90°C). The cool water was used to dissolve the mixture of zinc nitrate hexahydrate (Zn (NO₃)₂·6H₂O) and methenamine (C₆H₁₂N₄) in order to decrease the size of ZnO nanorods. From the X‐ray diffraction (XRD) results, it can be seen that the growth orientation of the as‐prepared ZnO nanorods was (002). Scanning electron microscopy (SEM) results illustrated that the nanorods had a hexagonal wurzite structure and average diameter of about 120nm. The average diameter of nanorods prepared by the cool water process was much smaller than that by the room‐temperature (RT) water process we always used. Photoluminescence (PL) measurements were also carried out. The result showed that a blue shift in UV emission band appeared in the PL spectrum of the sample grown with cool water process, which was mainly due to the reduction of tensile strain when the diameter of the ZnO nanorods decreased. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Low temperature hydrothermal growth and optical properties of ZnO nanorods

Well‐faceted hexagonal ZnO nanorods have been synthesized by a simple hydrothermal method at relative low temperature (90°C) without any catalysts or templates. Zinc oxide (ZnO) nanorods were grown in an aqueous solution that contained Zinc chloride (ZnCl₂, Aldrich, purity 98%) and ammonia (25%). Most of the ZnO nanorods show the perfect hexagonal cross section and well‐faceted top and side surfaces. The diameter of ZnO nanorods decreased with the reaction time prolonging. The samples have been characterized by X‐ray powder diffraction (XRD) and scanning electron microscopy (SEM) measurement. XRD pattern confirmed that the as‐prepared ZnO was the single‐phase wurtzite structure formation. SEM results showed that the samples were rod textures. The surface‐related optical properties have been investigated by photoluminescence (PL) spectrum and Raman spectrum. Photoluminescence measurements showed each spectrum consists of a weak band ultraviolet (UV) band and a relatively broad visible light emission peak for the samples grown at different time. It has been found that the green emission in Raman measurement may be related to surface states. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Fabrication and photocatalytic property of ZnO/SrTiO3 core/shell nanorod arrays

ZnO/SrTiO₃ core/shell nanorod arrays were fabricated by a facile two‐step method. ZnO nanorod arrays were first hydrothermally grown on Si substrate. Then, using liquid phase deposition method, SrTiO₃ were deposited onto the ZnO nanorods to form core/shell nanorod structures. The morphologies and structures of the products were characterized by scanning electron microscopy, transmission electron microscopy, and X‐ray diffraction. The photocatalytic behavior of the nanorod arrays was also examined through the photodegradation of methylene blue solution under UV irradiation. It was found that the core/shell nanorod arrays with deposition time of 10 min showed higher photocatalytic activity than bare ZnO nanorod arrays. This enhancement was attributed to the efficient charge separation at the ZnO/SrTiO₃ interface.     

Shape‐controlled synthesis of ZnO architectures

Several ZnO nanoarchitectures have been selectively prepared through hydrothermal method including urchin‐shaped, flower‐shaped, butterfly‐shaped, and cacti‐shaped microstructures. The influence of reaction temperature and the concentration of amphiphilic copolymer on the morphologies and shapes of ZnO samples have been studied. The samples were characterized using XRD, TEM, and SEM. It was found that ZnO nanorods or their assemblies were fabricated at higher temperature, whereas ZnO nanosheet architectures were produced at lower temperature. These flower‐shaped architectures possess high BET surface area of 27.43 m²/g. Room temperature UV‐VIS and PL spectra of the as‐obtained ZnO nanoarchitectures have been examined. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Solvothermal synthesis and growth mechanism of asymmetric ZnO hierarchical structures in diethylene glycol with ammonia solution

Several novel asymmetric ZnO hierarchical structures were synthesized in diethylene glycol (DEG) with different amount of ammonia solution via solvothermal process. The submicron‐rods or nanorods as the building units are distributed on the two sides in an asymmetric manner, resulting in formation of the shiitake‐like or bouquet‐like morphology. A possible formation mechanism was proposed on the basis of the experimental result. The consumption of the precursor could lead to a two‐step nucleation and growth process. The relative content of the [Zn(OH)₄]²⁻ and the [Zn(NH₃)₄]²⁺ precursors varies with the amount of ammonia solution, which affect the size and morphology of the asymmetric structures. The [Zn(OH)₄]²⁻ complex and the [Zn(NH₃)₄]²⁺ complex are absorbed on the positive (0001)‐Zn polar surface and the negative (000–1)‐O polar surface respectively, which lead to the alteration of growth rate of these polar surfaces.     

Graphene oxide used as a surfactant to induce the flower‐like ZnO microstructures: growth mechanism and enhanced photocatalytic properties

In this paper, graphene oxide (GO) was used as a temple to induce the formation of flower‐like ZnO microparticals compared with surfactants, such as cetyltrimethylammonium bromide (CTAB) and dodecyl dimethyl betaine (BS‐12). The zinc hydroxide carbonate ((Zn₄(CO₃)(OH)₆,ZHC)) was produced by a hydrothermal reaction. The flower‐like ZnO microparticals were gained by calcining ZHC. In the GO medium, the microparticals were assembled by numerous porous nanosheets from one point (initial nucleus) to flower‐like microparticals finally. The nanosheets of graphene oxide and functional groups were likely to contribute to the formation of the precursor, and some nanosheets were retained in the complex. The growth mechanism of ZHC was also proposed in this paper. The photocatalytic activity of the flower‐like ZnO microparticals was evaluated by photo degradation reaction of rhodamine B (RhB). The peony‐like porous ZnO/rGO compounds showed high photocatalytic activity and better than ZnO microparticals formed in the CTAB and BS‐12. These results indicated that GO could be widely used as a surfactant to induce composite materials with special morphology and photoelectric properties, etc.     

Investigation on growth defects in Pb(Zn1/3Nb2/3)O3‐PbTiO3 crystals

Relaxor ferroelectric crystal (1‐x)Pb(Zn_1/3Nb_2/3)O₃‐xPbTiO₃ (PZNT) with x=0.07 (PZNT93/7) has been grown by the vertical Bridgman method from the high temperature solution of PZNT‐PbO system. The growth defects, such as nucleation core, inclusions, boundaries and particles, were investigated by optical microscope and scanning electron microscope. Sub‐structures were found in the flux inclusions and the lack of ZnO component in PZNT crystals was attributed to the existence of ZnO particles in the inclusions. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Surface‐morphology evolution of ZnO nanostructures grown by hydrothermal method

Surface‐morphology evolution of ZnO nanocrystals has been observed by the hydrothermal process. The effects of stirring time and ammonia content on the morphology evolution have been discussed, respectively. Extension of stirring time of the precursor results in morphology transformation from star‐like to wire‐like ZnO nanocrystals. ZnO nuclei aggregation and uniform Zn(OH)₂ precipitation can readily explain these two morphologies, respectively. By increasing the ammonia content in the solution, the morphology of ZnO crystals is transformed from an irregular shape to hexagon sheets to nanorods, and the side length of ZnO crystals is decreased accordingly. Hollow structures are realized at the subsequent solution aging process. Variation of zinc ammonic complex and minimum surface energy can well explain the morphology evolution of ZnO nanostructures.     

Characterization of ZnO nanorods grown on Si substrates coated with NiCl2

ZnO nanorods were synthesized on NiCl₂‐coated Si substrates via a chemical vapor deposition (CVD) process. The as‐fabricated nanorods with diameters ranging from 150 nm to 200 nm and lengths up to several tens of micrometers grew preferentially arranged along [0001] direction, perpendicular to the (0002) plane. The clear lattice fringes in HRTEM image demonstrated the growth of good quality hexagonal single‐crystalline ZnO. Room temperature photoluminescence (PL) spectra illustrated that the ZnO nanorods exhibit strong UV emission peak and green emission peak, peak centers located at 388 nm and 506 nm. A possible growth mechanism based on the study of our X‐ray diffraction (XRD), electron microscopy and PL spectroscopy was proposed, emphasizing the effect of NiCl₂ solution (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and growth mechanism of ZnO rod‐like nanostructures by a microwave‐assisted low‐temperature aqueous solution route

A zinc oxide (ZnO) nanoarray (rod‐like nanostructure) was successfully synthesized through a low‐temperature aqueous solution and microwave‐assisted synthesis using zinc nitrate hexahydrate (Zn(NO₃)₂·6H₂O) and hexamethylenetetramine (HMTA) as raw materials, and using FTO glass as substrate. The effects of parameters in the preparation process, such as solution concentration, reaction temperature and microwave power, on the morphology and microstructure of ZnO nanoarray were studied. Phase structure and morphology of the products were characterized by X‐ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The results indicated that hexagonal wurtzite structure ZnO nanoarray with good crystallization could be prepared through a low‐temperature solution method. When the concentration of the mixed solution was 0.05 M, the reaction temperature was 95 °C, and the reaction time was 4 h, high‐density ZnO regular nanorods of 200 nm diameter were obtained. A possible mechanism with different synthesis methods and the influence of microwave processing are also proposed in this paper.     

Synthesis of zinc oxide crystals with different shapes from zincate aqueous solutions stabilized with triethanolamine

ZnO crystals were synthesized from basic aqueous solutions including zincate ions stabilized with triethanolamine (N(C₂H₄OH)₃, teaH₃) by heating at 60°C. The influence of the basicity of the solutions on the morphology of the ZnO crystals was examined. The aqueous solutions were prepared using ZnSO₄·7H₂O, N(CH₃)₄OH (TMAOH), and teaH₃ as a zinc source, a base, and a stabilizer, respectively, at a zinc concentration of 0.2 M at a teaH₃ / Zn molar ratio of 4. Clear solutions were obtained at a molar ratio of TMAOH / Zn ≥ 3.0. When the clear solutions, in which glass or polyester substrates were placed, were heated at 60°C, agglomerates of ZnO crystals were deposited on the substrates in the TMAOH / Zn range from 3.0 to 3.6. With increasing the TMAOH / Zn ratio, the shape of the resulting ZnO crystals changed from a short asymmetric column with a hexagonal flat edge and a rounded one, through a rocket‐like shape formed by intergrowth, to a hexagonal rod. Although no films of ZnO were formed, ZnO crystals with different shapes were synthesized. When the glass substrates pre‐coated with a ZnO thin film by a sol‐gel method were used, highly oriented, dense ZnO films were formed. The films consisted of rod‐like crystals aligned normal to the substrate surface. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Half opened microtubes of NaYF4:Yb,Er synthesized in reverse microemulsion under solvothermal condition

NaYF₄:Yb,Er micro/nanocrystals with different sizes and morphologies such as nanospheres, short flexural nanorods, and half opened microtubes, were synthesized in reverse microemulsion under solvothermal condition using the quaternary reverse microemulsion system, CTAB/1-butanol/cyclohexane/aqueous solution. The X-ray diffraction analysis confirmed that cubic phase NaYF₄:Yb,Er can completely transform to hexagonal phase with increasing reaction time. The scanning electron microscope and transmission electron microscope images revealed that the morphology of the product can be tailored by varying the reaction time. A possible crystalline growth process of the NaYF₄:Yb,Er micro/nanocrystals was discussed. The obtained half opened microtubes exhibited an intense green upconversion luminescence, which may be attractive in novel optoelectronic devices.     

Effects of passivation and postannealing on the photoluminescence properties of MgO/SiO2 core‐shell nanorods

MgO nanorods were grown by the thermal evaporation of Mg₃N₂ powders on the Si (100) substrate coated with a gold thin film. The MgO nanorods grown on the Si (100) substrate were a few tens of nanometers in diameter and up to a few hundreds of micrometers in length. MgO/SiO₂ core‐shell nanorods were also fabricated by the sputter‐deposition of SiO₂onto the MgO nanorods. Transmission electron microscopy (TEM) and X–ray diffraction (XRD) analysis results indicated that the cores and shells of the annealed core‐shell nanorods were a face‐centered cubic‐type single crystal MgO and amorphous SiO₂, respectively. The photoluminescence (PL) spectroscopy analysis results showed that SiO₂ coating slightly decreased the PL emission intensity of the MgO nanorods. The PL emission of the MgO/SiO₂ core‐shell nanorods was, however, found to be considerably enhanced by thermal annealing and strongly depends on the annealing atmosphere. The PL emission of the MgO/SiO₂ core‐shell nanorods was substantially enhanced in intensity by annealing in a reducing atmosphere, whereas it was slightly enhanced by annealing in an oxidative atmosphere. The origin of the PL enhancement by annealing in a reducing atmosphere is discussed with the aid of energy‐dispersive X‐ray spectroscopy analyses. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical and magnetic properties of Nd‐doped ZnO nanoparticles

Nd‐doped ZnO nanoparticles with different concentration were synthesized by sol‐gel method. The structures, magnetic and optical properties of as‐synthesized nanorods were investigated. X‐ray diffraction (XRD) and x‐ray photoelectron spectroscopy (XPS) results demonstrated that Nd ions were incorporated into ZnO lattice; but Zn_1‐xNd_xO nanoparticles with Nd concentration of x = 0.05 showed Nd₂O₃ phase, so the saturation concentration of Nd in Zn_1‐xNd_xO is less than 5 at%. Vibrating sample magnetometer (VSM) measurements indicated that Nd doped ZnO possessed dilute ferromagnetis behaviour at room temperature. Photoluminescence spectroscopy (PL) showed that Nd ions doping induced a red slight shift and decrease in UV emission with increase of Nd concentration.