Crystallography and cathodoluminescence of ultra‐long GaN nanowires

Ultra‐long GaN nanowires have been synthesized via a simple thermal evaporation process by heating mixed GaN and Ga₂O₃ powders in a conventional resistance furnace under ammonia gas at 1150 °C. The average length of GaN nanowires is estimated to be more than 100 μm after 30‐min growth, corresponding to a fast growth rate of more than 200 μm/h. Scanning electron microscope (SEM) observation indicated that the diameter of GaN nanowires was rather uniform along the growth direction and in the range of 100–200 nm. X‐ray diffraction (XRD) and transmission electron microscope (TEM) measurements confirmed that the GaN nanowires are crystalline wurtzite‐type hexagonal structure. Room‐temperature cathodoluminescence (CL) measurement indicated that an obvious red‐shift of the near band‐edge emission peak centered at 414 nm of the ultra‐long GaN nanowires and a wide shoulder in the range of 600–700 nm were observed. Possible reasons responsible for the red‐shift of the near band‐edge emission of the ultra‐long GaN nanowires was discussed. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Homoepitaxial growth and photoluminescence of self‐assembled In‐doped ZnS nanowire bundles

Self‐assembled In (Indium)‐doped ZnS nanowire bundles were synthesized via a thermal evaporation method without using any template. Vapor ‐ solid homoepitaxial growth was found to be the key reason for the formation of close‐packed nanowire bundles grown on the surface of microscale sphere‐shaped ZnS crystal. X‐ray diffraction (XRD), selected area electron diffraction (SAED), and transmission electron microscopy (TEM) analysis demonstrate that the In‐doped ZnS nanowires have the cubic structure, and there are numerous stacking faults along the <111> direction. Photoluminescence (PL) spectrum shows that the spectrum mainly includes two parts: a weak violet emission band centering at about 380 nm and a strong green emission band centering at about 510 nm. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Preparation,structure and photoluminescence properties of SiO2–coated ZnS nanowires

It is essential to passivate one‐dimensional (1D) nanostructures with insulating materials to avoid crosstalking as well as to protect them from contamination and oxidation. The structure and influence of thermal annealing on the photoluminescence properties of ZnS‐core/SiO₂‐shell nanowires synthesized by the thermal evaporation of ZnS powders followed by the sputter deposition of SiO₂ were investigated. Transmission electron microscopy and X‐ray diffraction analyses revealed that the cores and shells of the core‐shell nanowires were single crystal zinc blende‐type ZnO and amorphous SiO₂, respectively. Photoluminescence (PL) measurement showed that the core‐shell nanowires had a green emission band centered at around 525 nm with a shoulder at around 385 nm. The PL emission of the core‐shell nanowires was enhanced in intensity by annealing in an oxidative atmosphere and further enhanced by subsequently annealing in a reducing atmosphere. Also the origin of the enhancement of the green emission by annealing is discussed based on the energy‐dispersive X‐ray spectroscopy analysis results. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

α‐Fe2O3 nanospindles loaded with ZnO nanocrystals: Synthesis and improved gas sensing performance

ZnO/α‐Fe₂O₃ nanocomposites were fabricated through a two‐step hydrothermal method. The morphology and composition of the as‐synthesized products were characterized by X‐ray powder diffraction (XRD), field emission scanning electron microscopy (FESEM), energy‐dispersive X‐ray spectroscopy (EDS), transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM). The gas sensing properties of the fabricated products were investigated towards ethanol, acetone, propanol, isopropanol, formaldehyde, chloroform and so on. The results demonstrated that the ZnO/α‐Fe₂O₃ nanocomposites exhibited excellent sensing properties and showed remarkably higher sensing responses and much lower optimum operating temperature compared to individual ZnO and α‐Fe₂O₃. In addition, the ZnO/α‐Fe₂O₃ nanocomposites have some selectivity for ethanol, propanol and isopropanol. The possible gas sensing mechanism was also proposed. Our studies demonstrate that our fabricated materials could be widely used in the future.     

Cd2Ge2O6 nanowires grown by a simple hydrothermal route

Cd₂Ge₂O₆ nanowires have been synthesized by a simple hydrothermal route in the absence of any surfactants. The diameter and length of the Cd₂Ge₂O₆ nanowires with flat tips are 30‐300 nm and several dozens of micrometers, respectivley. X‐ray diffraction and high‐resolution transmission electron microscopy results show that the nanowires are composed of monoclinic Cd₂Ge₂O₆ phase. The growth condition dependence results show that the formation of the Cd₂Ge₂O₆ nanowires undergoes three morphological changes from spherical particles to nanorods, and finally to nanowires. The photoluminescence spectrum of the Cd₂Ge₂O₆ nanowires exhibits three fluorescence emission peaks centered at 422 nm, 490 nm and 528 nm showing the potential application for optical devices. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Hydrothermal synthesis of highly symmetric 26‐facet Cu2O polyhedra

Highly symmetric 26‐facet polyhedral microcrystals of cuprous oxide (Cu₂O) are successfully synthesized through a facile low temperature hydrothermal reaction. These polyhedra are constructed by well‐developed {100}, {110} and {111} crystallographic faces. The obtained microstructures were characterized by X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and Ultraviolet‐Visible (UV‐Vis) absorption spectrum. Cetyltrimethyl ammonium bromide (CTAB) and ethylenediaminetetraacetic acid disodium (EDTA‐2Na) have been confirmed to be necessary additives to the development of these perfect polyhedra. The growth process of the 26‐facet Cu₂O polyhedra is depicted on the grounds of the time‐dependent experiments. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structure and photoluminescence properties of SrWO4 3D microspheres synthesized by the surfactant‐assisted hydrothermal method

In this paper, we report large‐scale high‐quality SrWO₄ 3D microspheres synthesized in aqueous solutions under mild conditions with cetyl trimethyl ammonium bromide as a simple cationic surfactant. These crystals have been characterized by X‐ray diffraction, transmission electron microscopy and field emission scanning electron microscopy techniques. The crystal growth processes were employed to investigate the formation mechanism of SrWO₄ 3D microspheres. Room‐temperature photoluminescence indicated that the as‐prepared SrWO₄ 3D microcrystals had strong emission peaks at about 432 and 505 nm, respectively.     

Controlled synthesis of various morphologies of nanostructured zinc oxide: flower,nanoplate, and urchin

Nanoplates, flower‐like nanostructure of ZnO were successfully synthesized by employing ZnSO₄·7H₂O, NaOH as the starting materials at 120°C under hydrothermal condition. Keeping the same parameters, ZnO urchin shape was obtained by addition of vitamin C at 190°C. Characterizations were carried out by X‐ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) at room temperature. Selected area electron diffraction (SAED) pattern confirms that the product is single crystalline nature. The possible formation mechanisms for synthesized ZnO nanosturcture with various morphologies have also been proposed. PL spectrum from the ZnO flower‐like structures reveals weak UV emission and strong green emission. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and photoluminescence properties of GaN/ZnO core‐shell nanowires with their shells sputtered

We have reported the preparation of ZnO‐coated GaN nanowires and investigated changes in the structural and photoluminescence (PL) properties by the application of a thermal annealing process. For fabricating the core‐shell nanowires, Zn target was used to sputter ZnO shell onto GaN core nanowires. X‐ray diffraction (XRD) analysis indicated that the annealed core‐shell nanowires clearly exhibited the ZnO as well as GaN phase. The transmissoin electron microscopy (TEM) investigation suggested that annealing has induced the crystallization of ZnO shell layer. We have carried out Gaussian deconvolution analysis for the measured PL spectra, revealing that the core GaN nanowires exhibited broad emission which consist of red, yellow, blue, and ultraviolet peaks. ZnO‐sputtering induced new peaks in the green region. Thermal annealing reduced the relative intensity of the green emission. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Controlled synthesis of selenium of different morphologies at room temperature

A facile and convenient chemical precipitation route has been developed for the controlled growth of selenium nanowires and hierarchical microspheres at room temperature, with Na₂SeO₃ and hydrazine hydrate as starting materials in the presence of 1,2,3‐trimethylimidazolium tetrafluoroborate (tmimBF₄). The surface morphology of microspheres can be tuned by adjusting the reaction media. The products were characterized by X‐ray powder diffraction (XRD) and scanning electron microscope (SEM). Possible formation mechanisms of selenium nanowires and microspheres are proposed, respectively. The influences of the nature of reaction media, agitation and tmimBF₄ on the morphologies development were experimentally investigated and it was found that these factors were of great importance for the formation of Se morphologies. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural,Raman, and photoluminescence properties of double‐shelled coaxial nanocables of In2O3 core with ZnO and AZO shells

We synthesized In₂O₃/ZnO/Al‐doped ZnO (AZO) core‐double shell nanowires, in which the inner shell (ZnO) and the outer shell (AZO) have been subsequently deposited on the core In₂O₃ nanowires. With their one‐dimensional morphology being preserved, the X‐ray diffraction (XRD), lattice‐resolved transmission electron microscopy (TEM) image, selected area electron diffraction, and Raman spectrum coincidentally revealed that the shell was comprised of hexagonal ZnO phase. In addition, TEM‐EDX investigation revealed the presence of Al elements in the shell region. The thermal annealing at 700 °C did not significantly change the nanowire morphology, however, the XRD spectrum indicated that the ZnO phase was crystallized by the annealing. PL spectrum of the 700 °C‐annealed In₂O₃/ZnO/AZO core‐double shell nanowires was comprised of three Gaussian bands at approximately 2.1 eV, 2.4 eV, and 3.0 eV, respectively. The integrated intensities of 2.1 eV‐, 2.4 eV‐, and 3.0 eV‐bands were decreased by the thermal annealing. This study will pave the road to the preparation and applicaition of double‐shelled nanowires. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Controllable synthesis and field emission properties of In2O3 nanostructures

Large‐scale In₂O₃ nanorods, nanocubes and nanowires have been successfully synthesized by chemical vapor deposition route under atmospheric pressure. The structures and morphologies were characterized by x‐ray diffraction (XRD), scanning election microscopy (SEM) and high‐resolution transmission electron microscopy (HRTEM). The growth mechanisms of these In₂O₃ nanostructures were analyzed in detail based on the experimental results. Field‐emission measurements of these nanostructures demonstrated that nanorods with rectangular cross‐section possessed good performance with a turn‐on field of 2.47 Vμm^–1 and a field enhancement factor of 4597. The room‐temperature photoluminescence (PL) spectrum of the In₂O₃ nanostructure showed UV emission centered at about 396 nm and visible emissions located at 541 and 623 nm. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical,photocatalytic properties of novel CuS nanoplate‐based architectures synthesised by a solvothermal route

CuS architectures were successfully prepared by a simple solvothermal route without any surfactant, in which copper nitrate trihydrate and element sulfur were used as reactants. The products were characterized by X‐ray diffraction, field emission scanning electron microscopy, and transmission electron microscopy. The optical properties of CuS architectres were investigated by Raman spectrometer, ultraviolet‐visible spectroscopy, and fluorescence spectrophotometer. The results showed that the CuS architectures were hexagonal‐structured phase and composed of intersectional nanoplates. UV‐Vis absorption peaks of CuS architectures showed large blue shifts and PL spectrum exhibited a strong blue emission and a weak green emission. Photocatalytic activity of the CuS architectures was evaluated by measuring the decomposition rate of methylene blue solution under solar light. The CuS architectures show good photocatalytic activity. The effects of the molar ratio of Cu:S and the growth time on the synthesis of CuS crystalline were discussed and the growth mechanism of CuS nanoplate‐based architectures was also proposed. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Characterization of ZnO nanorods grown on Si substrates coated with NiCl2

ZnO nanorods were synthesized on NiCl₂‐coated Si substrates via a chemical vapor deposition (CVD) process. The as‐fabricated nanorods with diameters ranging from 150 nm to 200 nm and lengths up to several tens of micrometers grew preferentially arranged along [0001] direction, perpendicular to the (0002) plane. The clear lattice fringes in HRTEM image demonstrated the growth of good quality hexagonal single‐crystalline ZnO. Room temperature photoluminescence (PL) spectra illustrated that the ZnO nanorods exhibit strong UV emission peak and green emission peak, peak centers located at 388 nm and 506 nm. A possible growth mechanism based on the study of our X‐ray diffraction (XRD), electron microscopy and PL spectroscopy was proposed, emphasizing the effect of NiCl₂ solution (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and optical properties of CdO nanowires synthesized from Cd(OH)2 precursors by calcination

CdO nanowires were produced by calcination process using Cd(OH)₂nanowires as precursors. The Cd(OH)₂ nanowires were synthesized via arc discharge method submerged in de‐ionized water. Transmission electron microscopy (TEM) analysis of the as‐synthesized Cd(OH)₂ nanowires revealed that nanowire morphology was abundant form with the diameters range from 5 to 40 nm. In addition to the nanowire morphology, Cd(OH)₂ nanospheres and hexagonal shaped nanoparticles were also displayed. The Cd(OH)₂ nanostructures were used as precursors to produce CdO nanowires and calcinated in air at 400 °C for four hours. After calcination, the structural, morphological and optical properties of the as‐synthesized CdO nanowires were characterized by means of TEM, selected area electron diffraction (SAED), X‐ray diffraction (XRD) and UV‐vis spectroscopy. The XRD and SAED techniques showed that the as‐synthesized Cd(OH)₂ nanostructures could be transformed into CdO nanostructures after the calcination process. TEM results revealed that the as‐synthesized CdO nanowires were 5–30 nm in diameter and shorter than corresponding Cd(OH)₂ nanowires. In addition, the diameters of the spherical or irregular CdO nanoparticles ranged from 20 nm to 50 nm. UV‐vis spectroscopy analysis was showed that the direct gap of the CdO nanowires were found to be 2.60 eV which is slightly higher than the earlier reported values of the bulk CdO for direct band gaps (2.3 eV) due to quantum size effect. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Facile solvothermal synthesis,growth mechanism and thermoelectric property of flower‐like Bi2Te3

Hierarchical flower‐like Bi₂Te₃ was synthesized through a facile solvothermal method. The crystal structure and morphology of the as‐prepared samples were characterized by X‐ray diffraction (XRD), filed emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and high resolution TEM. The reaction parameters such as reaction time, the amount of glucose, concentration of NaOH and the reaction temperature were systematically investigated. Based on the FESEM observations, a possible mechanism defined as a self‐assembly process accompanied by anisotropic growth mechanism was proposed. Moreover, the thermoelectric properties were measured at the temperature range of 300–600 K. The hierarchical flower‐like Bi₂Te₃ presented good thermoelectrical properties. The maximum ZT value reached up to 0.6 at 600 K, which was higher than that of Bi₂Te₃ nanoparticles.     

Leaf‐like copper oxide nanocrystals synthesized by a gas‐liquid diffusion method at room temperature

The leaf‐like copper oxide (CuO) nanocrystals have been synthesized by a gas‐liquid diffusion method in pure aqueous solution at room temperature. The structure, morphologies and related properties of the as‐prepared crystals were characterized with X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), selected area electron diffraction (SAED) and thermogravimetric analysis (TG). The influence of copper concentration was investigated, which plays an important role in the formation of nanostructured CuO crystals. Only when the copper concentration was low enough (0.005 M) that the leaf‐like CuO could be obtained directly. Additionally, a growth mechanism of CuO was also proposed based on the observed results.     

Synthesis and photoluminescence properties of ZnO nanowire arrays

In this paper we report a chemical method named coordination reaction method to synthesize ZnO nanowire arreys. ZnO nanowires with the diameter about 80nm were successfully fabricated in the channels of the porous anodic alumina (PAA) template by the above coordination reaction method. The microstructures of ZnO/PAA assembly were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X‐ray diffraction (XRD). The results showed that the ZnO nanowires can be uniformly assembled into the nanochannels of PAA template. The growth mechanism of ZnO nanowires and the conditions of the coordination reaction are discussed. Photoluminescence (PL) measurement shows that the ZnO/PAA assembly system has a blue emission band caused by the various defects of ZnO. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Controllable synthesis,characterization and optical properties of Ag@AgCl coaxial core‐shell nanocables

Core‐shell structures often exhibit improved physical and chemical properties. Developing a relatively general, facile, and low temperature synthetic approach for core‐shell structures with complex compositions is still a particularly challenging work. Here we report a general chemical conversion route to prepare high quality Ag@AgCl coaxial core‐shell nanocables via the redox reaction between Ag nanowires and FeCl₃ in solution. The powder X‐ray diffraction of the Ag@AgCl coaxial core‐shell nanocables shows additional diffraction peaks corresponding to AgCl crystals apart from the signals from the Ag nanowire cores. Scanning electron microscopy and transmission electron microscopy images of the Ag@AgCl coaxial core‐shell nanocables reveal that the Ag nanowires are coated with AgCl nanoparticles. The effect of the molar ratio of Fe:Ag on the morphology and optical absorption of the Ag@AgCl coaxial core‐shell nanocables is systematically investigated. The result shows that the optical absorption of Ag nanowires decreases gradually and that of AgCl nanoparticles improves gradually with the increase of the molar ratio of Fe:Ag. The formation process of the Ag@AgCl coaxial core‐shell nanocables has been discussed in detail. The present chemical conversion approach is expected to be employed in a broad range of applications to fabricate innovative core‐shell structures with different compositions and shapes for unique properties. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis,conversion and comparison of the photocatalytic and electrochemical properties of ZnSe·N2H4 and ZnSe microrods

Novel ZnSe·N₂H₄ complex microrods with ∼2 μm in length and 100∼200 nm in diameter were successfully prepared by the solvothermal method at 110°C for 10 h, employing ZnAc₂·2H₂O and Se powders as the reactants, N₂H₄·H₂O as the reductant and medium. Experiments showed that the as‐obtained complex could be further converted into pure hexagonal ZnSe in an ethanol medium at 180 °C for 10 h, and the morphology hardly changed. The as‐prepared products were characterized by X‐ray powder diffraction (XRD), Energy dispersive spectrum (EDS), IR spectrum, Thermogravimetric (TG) analysis and Field emission scanning electron microscopy (SEM). Also, their photocatalytic degradation and electrochemical property were compared. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)