Optical and electrical studies on spray deposited ZnO thin films

ZnO thin films were prepared by spray pyrolytic decomposition of zinc acetate onto a glass substrate. These films were analyzed for the optical and electrical properties. Optical studies show that in these films the electronic transition is of the direct transition type. The optical energy gap for the films of different thicknesses is estimated to be in the range 2.98 – 3.09 eV. Electrical studies indicate that the films exhibit thermally activated electronic conduction and the activation energies are found to be dependent on the film thickness. The complex impedance measurements were carried out over a wide range of frequencies at room temperature (300 K). All the impedance spectra contain only a single arc, but the arc has a non‐zero intersection with the real axis in the high frequency region. Also, the arc has its centre lying below with the real axis which indicates the multirelaxation behavior of the films. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of solvent volume on the physical properties of sprayed fluorine‐doped zinc oxide thin films

Fluorine‐doped zinc oxide (FZO) films were deposited from aged starting solutions having different solvent volumes (10, 20, 30, 40 and 50 ml) using a simplified spray pyrolysis technique. The electrical studies showed that the resistivity is minimum (4.68 × 10^–2 Ω cm) for lowest solvent volume (10 ml) and the value progressively increased with the increase in the solvent volume indicating that the fluorine incorporation increases with solvent volume. The systematic study clearly showed that the spray flux rate plays a crucial role in determining the electrical, optical, surface and structural properties of the FZO films. The optical transparency is found to be gradually increased (from 85 to 95%) as the volume of the solvent increases. The scanning electron microscope images depicted that the decrease in the spray flux rate caused an enhancement in the grain size. The X‐ray diffraction profile clearly showed that all the films have preferential orientation along the (002) plane with hexagonal wurtzite structure. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical studies on ZnO films prepared by sol‐gel method

A standard sol‐gel method was used to deposit ZnO thin films of suitable thickness on glass substrate.The optical characteristics of the visible to infrared range on thermal stress were critically observed. Morphological signature of the films was detected by X‐ray diffraction (XRD) and the crystallite size determined by Scherrer method from XRD data were consistent with grain size estimated from spectroscopic data through Meulenkamp equation. The optical band gap value from the transmission spectrum was found to corroborate with the existing works. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Spray deposition and characterization of undoped and In‐doped tin disulphide thin films

Undoped and Indium doped tin disulphide (SnS₂) thin films had been deposited onto glass substrates at T_s = 300 °C using spray pyrolysis technique under atmospheric pressure with stannous chloride, indium chloride and thiourea as precursors. The structural, optical and electrical properties of the deposited films were characterized. The XRD pattern revealed that the undoped and doped films had preferred orientation along (002) plane with hexagonal structure. FESEM micrographs had shown that morphologies of the films changed with indium doping. Optical constant such as refractive index (n), extinction coefficient (k), real and imaginary parts of dielectric constants were evaluated from transmittance and reflectance spectra in UV‐Visible spectroscopy. The optical absorption data were used to determine the band gap energy and it was found to be 2.75 eV for undoped and 2.50 eV for indium doped films respectively. The room temperature dark resistivity was found to be 4.545 × 10³ Ω‐cm and 5.406 × 10³ Ω‐cm for undoped and In‐doped films respectively.     

Nanocrystalline transparent SnO2‐ZnO films fabricated at lower substrate temperature using a low‐cost and simplified spray technique

Nanocrystalline and transparent conducting SnO₂‐ ZnO films were fabricated by employing an inexpensive, simplified spray technique using a perfume atomizer at relatively low substrate temperature (360±5 °C) compared with conventional spray method. The structural studies reveal that the SnO₂‐ZnO films are polycrystalline in nature with preferential orientation along the (101) plane. The dislocation density is very low (1.48×10¹⁵lines/m²), indicating the good crystallinity of the films. The crystallite size of the films was found to be in the range of 26–34 nm. The optical transmittance in the visible range and the optical band gap are 85% and 3.6 eV respectively. The sheet resistance increases from 8.74 kΩ/□ to 32.4 kΩ/□ as the zinc concentration increases from 0 to 40 at.%. The films were found to have desirable figure of merit (1.63×10^–2 (Ω/□)^–1), low temperature coefficient of resistance (–1.191/K) and good thermal stability. This simplified spray technique may be considered as a promising alternative to conventional spray for the massive production of economic SnO₂ ‐ ZnO films for solar cells, sensors and opto‐electronic applications. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Sputter power and sputter pressure influenced structural and optical behaviour of RF sputtered nanocrystalline ZnO films

Zinc oxide thin films were deposited on p‐type (100) silicon and Corning glass substrate by using RF magnetron sputtering at different sputter powers range 100–200 W and sputter pressures range 2–8 Pa. The deposited films were characterized by X‐ray diffraction, atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscope and UV‐Vis‐NIR spectrophotometer. The films formed at sputter power of 100 W consists of weak (100) reflection and then sputter power increased to 150 W additional (110) reflection was present with enhancement in the intensity of (100) peak. Further increase of sputtering power to 200 W the intensity of (100) phase decreased with the presence of additional peaks of (002) and (101) of ZnO. The FTIR analysis confirms the Zn‐O absorption band was located at 414 cm^‐1. The optical band gap of zinc oxide films decreased from 3.28 to 3.07 eV with increase of sputter power from 100 to 200 W. The maximum crystallite size of 21 nm, the root mean square roughness of 7.2 nm was found at films formed at working pressure of 5 Pa. The optical transmittance of the films increased from 88 to 96% and then decreased to 84% with increase of sputter pressure from 2 to 8 Pa.     

Structural and optical properties of Mg‐doped ZnO thin films prepared by a modified Pechini method

ZnO thin films with different Mg doping contents (0%, 3%, 5%, 8%, 10%, respectively) were prepared on quartz glass substrates by a modified Pechini method. XRD patterns reveal that all the thin films possess a polycrystalline hexagonal wurtzite structure. The peak position of (002) plane for Mg‐doped ZnO thin films shifts toward higher angle due to the Mg doping. The crystallite size calculated by Debey‐Scherrer formula is in the range of 32.95–48.92 nm. The SEM images show that Mg‐doped ZnO thin films are composed of dense nanoparticles, and the thickness of Mg‐doped ZnO thin films with Mg doped at 8% is around 140 nm. The transmittance spectra indicate that Mg doping can increase the optical bandgap of ZnO thin films. The band gap is tailored from 3.36 eV to 3.66 eV by changing Mg doping concentration between 3% and 10%. The photoluminescence spectra show that the ultraviolet emission peak of Mg‐doped ZnO thin films shifts toward lower wavelength as Mg doping content increases from 3% to 8%. The green emission peak of Mg‐doped ZnO thin films with Mg doping contents were 3%, 8%, and 10% is attributed to the oxygen vacancies or donor‐acceptor pair. These results prove that Mg‐doped ZnO thin films based on a modified Pechini method have the potential applications in the optoelectronic devices.     

Morphology,composition, structure and optical properties of thermally annealed Cu2O thin films prepared by reactive DC sputtering method

Abstract

Thin films copper oxides are perspective materials for many optoelectronic applications, including photovoltaics. The samples were deposited on glass and silicon substrates by magnetron sputtering method using Modular Platform PREVAC. After deposition the samples were thermally treated by annealing in oxygen atmosphere for 60?min at 450?°C. Morphology confirms that all the films have crystalline structure. Optical measurements show that the films have wide band gap within the range 2.20÷2.48?eV before and 2.03÷2.40?eV after annealing. The article presents the discussion about the influence of annealing on Cu₂O thin film parameters.     

Synthesis and characterization of manganese sulphide thin films deposited by spray pyrolysis

Manganese sulphide (MnS) thin films have been deposited onto glass substrate by a low cost spray‐pyrolysis technique at 220 °C. The as‐deposited MnS thin films have been characterized using scanning electron microscopy (SEM), energy dispersive X‐ray (EDX) spectroscopy, atomic force microscopy (AFM), X‐ray diffraction, UV visible spectroscopy and photo electrochemical (PEC) measurement. The SEM and AFM images showed that the MnS thin films were well covered onto the substrate surface. The as‐deposited raw thin film was found to be amorphous in nature and perfectly crystalline phase after annealing the sample. Optical band gap of the MnS thin films was found to vary from 3.1 to 3.21 eV and the band gap decreases with the increase in film thickness. Optical constants such as refractive index, extinction coefficient have been evaluated using reflectance and absorbance data. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and optoelectrical properties of Ga‐doped ZnO semiconductor thin films grown by magnetron sputtering

Transparent conductive gallium‐doped zinc oxide (Ga‐doped ZnO) films were prepared on glass substrate by magnetron sputtering. The influence of substrate temperature on structural, optoelectrical and surface properties of the films were investigated by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), spectrophotometer, four‐point probe and goniometry, respectively. Experimental results show that all the films are found to be oriented along the c‐axis. The grain size and optical transmittance of the films increase with increasing substrate temperature. The average transmittance in the visible wavelength range is above 83% for all the samples. It is observed that the optoelectrical property is correlated with the film structure. The Ga‐doped ZnO film grown at the substrate temperature of 400 °C has the highest figure of merit of 1.25 × 10⁻² Ω⁻¹, the lowest resistivity of 1.56 × 10⁻³ Ω·cm and the highest surface energy of 32.3 mJ/m².     

Crystallographic,optical and magnetic properties of Co‐doped ZnO thin films synthesized by sol gel route

ZnO thin films with various Co doping levels (0%, 1%, 3%, 5%, 8%, respectively) have been synthesized by sol gel spin coating method on glass substrates. XRD and XPS studies of the films reveal that cobalt ions are successfully doped into ZnO crystal lattice without changing the hexagonal wurtzite structure. The morphologies are studied by SEM and AFM and show wrinkle network structures with uniform size distribution. With Co doping concentration increasing, the wrinkle network width decreases gradually. The transmittance spectra indicate that Co doping can effectively reduce the optical bandgap of ZnO thin films. Photoluminescence show that all samples have ultraviolet, violet and green emission. When Co doping concentration increases up to 5%, the intensity of violet emission is greatly increased and a strong deep blue emission centered at 439 nm appears. The ferromagnetism of all samples was observed at room temperature. The emission mechanisms and ferromagnetism origination are discussed in detail. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical characterization of thermally evaporated thin CdO films

Cadmium Oxide films have been prepared by vacuum evaporation method on a glass substrate at room temperature. Detailed structural, optical, and electrical properties of the films are presented at different annealing temperatures. The crystal structure of the samples was studied by X‐ ray diffraction. The spectral absorption coefficient of the CdO film at the fundamental absorption region (450‐650nm) was determined using the spectral data of transmittance. The direct and indirect band gap energies were determined and found to be 2.33 eV and 1.95 eV respectively. The third order optical nonlinearities χ(3) of CdO films has been measured used the z‐can technique. The real and imaginary parts of χ(3) have been measured at 514 nm and found to be 1.7x10^‐3 esu and 3.0x10^‐3 esu, respectively. (© 2003 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Studies on optical properties of polycrystalline SnO2:Sb thin films prepared using SnCl2 precursor

Optical properties of spray deposited antimony (Sb) doped tin oxide (SnO₂) thin films, prepared from SnCl₂ precursor, have been studied as a function of antimony doping concentration. The doping concentration was varied from 0‐4 wt.% of Sb. All the films were deposited on microscope glass slides at the optimized substrate temperature of 400 °C. The films are polycrystalline in nature with tetragonal crystal structure. The doped films are degenerate and n‐type conducting. The sheet resistance of tin oxide films was found to decrease from 38.22 Ω/□ for undoped films to 2.17 Ω/□ for antimony doped films. The lowest sheet resistance was achieved for 2 wt.% of Sb doping. To the best of our knowledge, this sheet resistance value is the lowest reported so far, for Sb doped films prepared from SnCl₂ precursor. The transmittance and reflectance spectra for the as‐deposited films were recorded in the wavelength range of 300 to 2500 nm. The transmittance of the films was observed to increase from 42 % to 55 % (at 800 nm) on initial addition of Sb and then it is decreased for higher level of antimony doping. This paper investigates the variation of optical and electrical properties of the as‐deposited films with Sb doping. (© 2003 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical properties of Al‐doped ZnO thin films deposited by two different sputtering methods

Aluminum‐doped zinc oxide (AZO) thin films were deposited on sapphire (002) and glass substrates by two different sputtering techniques radio frequency magnetron cosputtering of AZO and ZnO targets and sputtering of an AZO target. The dependence of the photoluminescence (PL) and transmittance properties of the AZO films deposited by cosputtering and sputtering on the AZO/ZnO target power ratio, R and the O₂/Ar flow ratio, r were investigated, respectively. Only a deep level emission peak appears in the PL spectra of cosputtered AZO films whereas both UV emission and deep level emission peaks are observed in the PL spectra of sputtered AZO films. The absorption edges in the transmittance spectra of the AZO films shift to the lower wavelength region as R and r increase. Also effects of crystallinity, surface roughness, PL on the transmittance of the AZO films were explained using the X‐ray diffraction (XRD), atomic force microscopy (AFM), and PL analysis results. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Microstructural,optical and electrical properties of GeO2 thin films prepared by sol‐gel method

GeO₂ thin films were prepared by sol‐gel method on ITO/Glass substrate. The electrical and optical properties and the microstructures of these films were investigated with special emphasis on the effects of an annealing treatment in ambient air. The films were annealed at various temperatures from 500 °C to 700 °C. Structural analysis through X‐ray diffraction (XRD) and atomic force microscope (AFM) showed that surface structure and morphological characteristics were sensitive to the treatment conditions. The optical transmittance spectra of the GeO₂/ITO/Glass were measured using a UV‐visible spectrophotometer. All films exhibited GeO₂ (101) orientation perpendicular to the substrate surface where the grain size increased with increasing annealing temperature. The optical transmittance spectroscopy further revealed high transparency (over 70 %) in the wave range 400 – 800 nm of the visible region. At an annealing temperature level of 700 °C, the GeO₂ films were found to possess a leakage current density of 1.31×10^‐6A/cm² at an electrical field of 20 kV/cm. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of gamma radiation on the absorption spectra and optical energy gap of Li‐ doped ZnO thin films

We have studied the effect of subsequent gamma (γ) irradiation on the absorption spectra and the optical energy gap of ZnO thin films doped with Li (ZnO:Li). The optical transmission (T) and optical reflection (R) in the wavelength range 190∼800 nm of films deposited at 300 °C on sapphire, MgO or quartz substrates were measured. The dependence of the absorption coefficient α on photon energy hν was determined as a function of γ‐doses. The films show direct allowed interband transition that influenced by the gamma doses. Both the optical energy gap E^opt_g and the absorption coefficient (α) were found to be γ‐dose dependent. The results can be discussed on the basis of γ‐irradiation‐induced defects in the film and on the film structure. The absorption coefficient exhibits exponential dependence on photon energy obeying Urbach's rule in the absorption edge. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Comparison of tin‐doped indium oxide films fabricated by spray pyrolysis and magnetron sputtering

A comparison of the properties between Tin‐doped Indium Oxide (ITO) films fabricated by sputtering and spray pyrolysis is presented. This analysis shows that the ITO films fabricated by DC magnetron sputtering in pure argon gas requires of a subsequent annealing for the improvement of their structural, electrical and optical properties, when they are compared to films fabricated by single‐stage spray pyrolysis process that includes a new approach. The optimum annealing temperature for ITO films sputtered at room temperature lies in the 300‐350 °C range. Under such conditions, the ITO sputtered films are slightly more resistive than the resistivity (2 × 10^‐4 Ω‐cm) shown by films sprayed at 480 °C using a solution with a 5 % of tin to indium ratio, and almost four times the worst value of the combination of transparency and conductivity determined by the value of the figure of merit (FOM). The sprayed films have a high value of the FOM, 2.9×10^‐2 Ω^‐1, which is comparable with the best published results.     

Substrate temperature effect on the optical properties of amorphous Sb2S3 thin films

Sb₂S₃ amorphous thin films were prepared by thermal evaporation of corresponding powder on thoroughly cleaned glass substrates held at temperature in the range 300‐473 K. X‐ray diffraction and atomic force microscopy have been used to order to identify the structure and morphology of surface thin films. The optical constants of the deposition films were obtained from the analysis of the experimental recorded transmission data over the wavelength range 400‐1400 nm. An analysis of the absorption coefficient values revealed an optical indirect transition with the estimation of the corresponding band gap values. It was found that the optical band gap energy decrease with substrate temperature from 1.67 eV at 300 K to 1.48 eV at 473K. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Properties of InAs co‐doped ZnO thin films prepared by pulsed laser deposition

InAs co‐doped ZnO films were grown on sapphire substrates by pulsed laser deposition. The grown films have been characterized using X‐ray diffraction (XRD), Hall effect measurements, Atomic force microscope (AFM) and Field emission scanning electron microscope (FESEM) in order to investigate the structural, electrical, morphological and elemental properties of the films respectively. XRD analysis showed that all the films were highly orientated along the c‐axis. It was observed from Hall effect measurements that InAs co‐doped ZnO films were of n‐type conductivity. In addition, the presence of In and As has been confirmed by Energy dispersive X‐ray analysis. AFM images revealed that the surface roughness of the films was decreased upon the co‐doping. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structure and optical properties of Mg‐doped ZnO nanoparticles by polyacrylamide method

Mg‐doped ZnO (Mg_xZn_1‐xO) nanoparticles with precise stoichiometry are synthesized through polyacrylamide polymer method. Calcination of the polymer precursor at 650 °C gives particles of the homogeneous solid solution of the (Mg_xZn_1‐xO) system in the composition range (x < 0.15). ZnO doping with Mg causes shrinkage of lattice parameter c. The synthesized Mg_xZn_1‐xO nanoparticles are typically with the diameter of 70–85 nm. Blue shift of band gap with the Mg‐content is demonstrated, and photoluminescence (PL) from ZnO has been found to be tunable in a wide range from green to blue through Mg doping. The blue‐related PL therefore appeared to be caused by energetic shifts of the valence band and/or the conduction band of ZnO. Mg_xZn_1‐xO nanoparticles synthesized by polyacrylamide‐gel method after modified by polyethylene glycol surfactant have a remarkable improvement of stability in the ethanol solvent, indicating that these MZO nanoparticles could be considered as the candidate for the application of solution–processed technologies for optoelectronics at ambient temperature conditions.