Unusual behavior of PEG/PPG/Pluronic interfaces studied by a spinning drop tensiometer

The effects of surfactants on the interfacial tension driven retraction of elongated drops were studied in a spinning drop tensiometer. Experiments were conducted on polypropylene glycol (PPG) drops suspended in polyethylene glycol (PEG), with Pluronic block copolymers as surfactants. Two unusual observations are reported here. In the first, initially-elongated drops generated at high rotational speed were allowed to retract by reducing the rotational speed. Pluronic-laden drops would not retract completely, but would instead maintain strongly nonspherical shapes indefinitely. We attribute such "nonretraction" to an interfacial yield stress induced by the Pluronic surfactant. In the second, drops being heated while spinning at a constant speed would elongate sharply at some temperature, and subsequently breakup. Such "autoextension" and breakup indicate complex nonmonotonic changes in interfacial tension with time during heating. We propose that autoextension occurs because at low temperature, interfacially-adsorbed surfactant is crystallized and hence trapped at the interface at a concentration far above equilibrium.     

Gemini阴离子表面活性剂水溶液的界面活性

Gemini阴离子表面活性剂水溶液的界面活性;Gemini阴离子表面活性剂;表面张力;CMC;C20;界面张力     

Volume of a nanoscale water bridge

Water bridges formed through capillary condensation at nanoscale contacts first stretch and then break during contact rupture. Atomic force microscopy (AFM) pull-off experiments performed in air with hydrophilic tips and samples show that stretched nanoscopic water bridges are in mechanical equilibrium with the external pull-off force acting at the contact but not in thermodynamic equilibrium with the water vapor in air. The experimental findings are explained by a theoretical model that considers constant water volume and decrease of water meniscus curvature during meniscus stretching. The model predicts that the water bridge breakup distance will be roughly equal to the cubic root of the water bridge volume. A thermodynamic instability was noticed for large water bridges formed at the contact of a blunt AFM tip (curvature radius of 400 nm) with a flat sample. In this case, experiments showed rise and stabilization of the volume of the water at the contact in about 1 s. For sharp AFM tips (curvature radius below 50 nm), the experiments indicated that formation of stable water bridges occurs in a much shorter time (below 5 ms).     

Enhanced ion signals in desorption electrospray ionization using surfactant spray solutions

Solvent optimization is an important procedure in desorption electrospray ionization (DESI) and in this study the effects of solvent surface tension are explored. Data are presented for methanol/water/surfactant solvent systems, which show increases in ion signals of more than an order of magnitude when low concentrations of surfactants are added to the standard methanol/water (1:1) spray solvent. Examples of analytes tested include food chemicals, peptides, pharmaceuticals, and drugs of abuse. The improvement in ion intensity is mainly attributed to the effect of surface tension in producing smaller spray droplets, which are shown to cover a larger surface area. Surfactant-containing spray solutions allowed extension of DESI-MS analysis to previously intractable analytes like melamine and highly hydrophobic compounds like the sudan dyes.     

A Growing Drop Technique for Measuring Dynamic Interfacial Tension

A novel, growing drop technique is described for measuring dynamic interfacial tension due to sorption of surface-active solutes. The proposed method relates the instantaneous pressure and size of expanding liquid drops to the interfacial tension and is useful for measuring both liquid/gas and liquid/liquid tensions over a wide range of time scales, currently from 10 ms to several hours. Growing drop measurements on surfactant-free water/ air and water/octanol interfaces yield constant tensions equal to their known literature values. For surfactant-laden, liquid drops, the growing drop technique captures the actual transient tension evolution of a single interface, rather than interval times as with the classic maximum-drop-pressure and drop-volume tension measurements. Dynamic tensions measured for 0.25 mM aqueous 1-decanol solution/air and 0.02 kg/m³ aqueous Triton X-100 solution/dodecane interfaces show nonmonotonic behavior, indicating slow surfactant transport relative to the imposed rates of interfacial dilatation. The dynamic tension of a purified and fresh 6 mM aqueous sodium dodecyl sulfate (SDS) solution/air interface shows only a monotonic decrease, indicating rapid surfactant transport relative to the imposed rates of dilatation. Conversely, an aged SDS solution, naturally containing trace dodecanol impurities, exhibits dynamic tensions which reflect a superposition of the rapidly equilibrating SDS and the slowly adsorbing dodecanol.     

Numerical investigation of the effect of insoluble surfactants on drop deformation and breakup in simple shear flow

The effect of insoluble surfactants on drop deformation and breakup in simple shear flow is studied using a combination of a three-dimensional boundary-integral method and a finite-volume method to solve the coupled fluid dynamics and surfactant transport problem over the evolving interface. The interfacial tension depends nonlinearly on the surfactant concentration, and is described by the equation of state for the Langmuir isotherm. Results are presented over the entire range of the viscosity's ratio lambda and the surface coverage x, as well as the capillary number Ca that spans from that for small deformation to values that are beyond the critical one Ca(cr). The values of the elasticity number E, which reflects the sensitivity of the interfacial tension to the maximum surfactant concentration, are chosen in the interval 0.1 < or = E < or = 0.4 and a convection dominated regime of surfactant transport, where the influence of the surfactant on drop deformation is the most significant, is considered. For a better understanding of the processes involved, the effect of surfactants on the drop dynamics is decoupled into three surfactant related mechanisms (dilution, Marangoni stress and stretching) and their influence is separately investigated. The dependence of the critical capillary number Ca(cr)(lambda) on the surface coverage is obtained and the boundaries between different modes of breakup (tip-streaming and drop fragmentation) in the (lambda; x) plane are searched for. The numerical results indicate that at low capillary number, even with a trace amount of surfactant, the interface is immobilized, which has also been observed by previous studies. In addition, it is shown that for large Péclet numbers the use of the small deformation theory to measure the interfacial tension in the case where surfactants are present can introduce a significant error.     

Emulsion drops in external flow fields — The role of liquid interfaces

We review the flow of emulsion drops, focusing on recent work involving complex interfaces, which may include the presence of surfactants, particles, surface-active polymers, or solid-like membrane layers. En route, important phenomena in multiphase flow associated with emulsion rheology are considered, including drop coalescence and breakup, surfactant transport, or the mechanics of composite interfaces.     

Effect of surfactants on wetting of super-hydrophobic surfaces

The effect of surfactants on wetting behavior of super-hydrophobic surfaces was investigated. Super-hydrophobic surfaces were prepared of alkylketene dimer (AKD) by casting the AKD melt in a specially designed mold. Time-dependent studies were carried out, using the axisymmetric drop shape analysis method for contact angle measurement of pure water on AKD surfaces. The results show that both advancing and receding contact angles of water on the AKD surfaces increase over time ( approximately 3 days) and reach the values of about 164 and 147 degrees , respectively. The increase of contact angles is due to the development of a prickly structure on the surface (verified by scanning electron microscopy), which is responsible for its super-hydrophobicity. Aqueous solutions of sodium acetate, sodium dodecyl sulfate, hexadecyltrimethylammonium bromide, and n-decanoyl-n-methylglucamine were used to investigate the wetting of AKD surfaces. Advancing and receding contact angles for various concentrations of different surfactant solutions were measured. The contact angle results were compared to those of a number of pure liquids with surface tensions similar to those of surfactant solutions. It was found that although the surface tensions of pure liquids and surfactant solutions at high concentrations are similar, the contact angles are very different. Furthermore, the usual behavior of super-hydrophobic surfaces that turn super-hydrophilic when the intrinsic contact angle of liquid on a smooth surface (of identical material) is below 90 degrees was not observed in the presence of surfactants. The difference in the results for pure liquids and surfactant solutions is explained using an adsorption hypothesis.     

Solution/air interfaces I. An oscillating jet relative method for determining dynamic surface tensions

The oscillating jet method has been investigated for the determination of the surface tension of water using horizontal jets from elliptical orifices in bell-shaped and uniform-channel tubes. Improved techniques have been developed for measuring the wave parameters, the flow rate and for extending the range of investigations to include the initial 80–90 msec of jet surface age.The surface tension values, calculated using the Bohr equation from measurements on successive waves of the water jets, were dependent on the characteristics of the orifice, its position, the flow rate and the wave serial number, but were within ±2 mN/m of the equilibrium value if the initial wave values were disregarded. An extension of the Bohr equation developed for vertical jets was found to be invalid for horizontal jets.Calculated surface tension versus surface age relationships for surfactant solutions also varied with the experimental conditions, but by fixing the position of the orifice tube, and standardizing with water, a relative method was developed for determining dynamic tensions that were independent of the tube used and of the flow rate. The validity of the method was illustrated by results obtained with two surfactant solutions using seven tubes (bell-shaped and uniform-channel) over an age range from 0.6 to 75 msec. The surface tensions of deionized water samples have been determined by the relative method and compared with those obtained by a static method.The true surface age along the jet surface is concluded to be close to the value derived from the mean axial velocity.Evidence is given indicating that, within the millisecond age range, water does not have a dynamic tension above the equilibrium value.     

Effect of glycerol on micelle formation by ionic and nonionic surfactants at 25 degrees C

The effect of glycerol on the micellization of the cationic surfactant cetyltrimethylammonium bromide (CTAB) and of the ethoxylated nonionic surfactant Brij 58 has been investigated by various experimental techniques. For both surfactants the critical micellar concentration (cmc), determined by surface tension measurements, is almost unaffected by the presence of glycerol in the mixture; only at high glycerol concentrations (>/=20% w/w) does the cmc significantly increase. The area per surfactant molecule at the air-solution interface, A, increases with increasing glycerol weight percentage, w(g). Fluorescence quenching measurements indicate that the presence of glycerol induces a lowering of the aggregation number of both surfactants. The glycerol intradiffusion coefficient has been measured by the pulsed-gradient spin-echo NMR technique as a function of glycerol content at constant surfactant concentration. It is almost unaffected by the presence of the surfactants, indicating that no direct glycerol-surfactant interaction occurs in the mixture. The surfactant intradiffusion coefficient has been also measured. In the case of CTAB, it increases with increasing glycerol concentration, a reflection of the decreased aggregation number. For Brij 58, in spite of the lowering of the aggregation number, the surfactant intradiffusion coefficient decreases with increasing glycerol concentration, suggesting an increase of the intermicellar interaction. The experimental evidence shows that for both surfactants the micellization is affected by the presence of glycerol through an indirect, solvent-mediated mechanism. In the case of CTAB, the main effect of glycerol is a lowering of the medium dielectric constant, which enhances the electrostatic interactions in solution. In the case of Brij 58, the results can be interpreted in terms of a salting-out effect according to which glycerol competes with the surfactant for water molecules, causing a dehydration of the surfactant ethoxylic headgroup.     

Effect of nonionic surfactant on wetting behavior of an evaporating drop under a reduced pressure environment

The evaporation of sessile drops at reduced pressure is investigated. The evaporation of water droplets on aluminum and PTFE surfaces at reduced pressure was compared. It was found that water droplets on an aluminum surface exhibit a 'depinning jump' at subatmospheric pressures. This is when a pinned droplet suddenly depins, with an increase in contact angle and a simultaneous decrease in the base width. The evaporation of sessile water droplets with a nonionic surfactant (Triton X-100) added to an aluminum surface was then studied. The initial contact angle exhibited a minimum at 0.001 wt% Triton X-100. A maximum in the evaporation rate was also observed at the same concentration. Droplets with low surfactant concentrations are found to exhibit the 'depinning jump.' It is thought that the local concentration of the surfactant causes a gradient of surface tension. The balance at the contact angle is dictated by complex phenomena, including surfactant diffusion and adsorption processes at interfaces. Due to the strong evaporation near the triple line, an accumulation of the surfactant will lead to a surface tension gradient along the interface. The gradient of surface tension will influence the wetting behavior (Marangoni effect). At low surfactant concentrations the contact line depins under the strong effect of surface tension gradient that develops spontaneously over the droplet interface due to surfactant accumulation near the triple line. The maximum evaporation rate corresponds to a minimum contact angle for a pinned droplet.     

A study of oil droplet coalescence

Oil droplets dispersed in water can be readily studied when they are coated with surfactants, which lower their interfacial tension and enhance their stability. Pure oil droplets are more difficult to study because of their high interfacial tension, which facilitates coalescence and the adsorption of contaminants. In this study, we have characterised the surface charging properties of a water insoluble oil, bromododecane, which has a density close to water. The small density difference allows us to study relatively large drops of this oil and to analyse its coalescence behaviour. The results obtained with this simple, surfactant-free, system suggest that an additional attractive force, such as the long range hydrophobic interaction, might be required to explain oil droplet coalescence behaviour.     

A numerical study of the effect of insoluble surfactants on the stability of a viscous drop translating in a Hele-Shaw cell

A circular drop is a linearly stable solution for the buoyancy-driven motion of drops in a Hele-Shaw cell [Gupta et al. J. Colloid Interface Sci.218(1), 338 (1999)]. In the absence of surface-active agents, an initially prolate drop always goes to a steady circular shape while initially oblate drops exhibit complex dynamics [Gupta et al. J. Colloid Interface Sci.222, 107 (2000)]. In this study, the effect of insoluble surfactant impurities on the critical conditions for drop breakup is explored by using the Langmuir adsorption framework in conjunction with a physically based expression for the depth-averaged tangential stress exerted on a two-phase interface in a Hele-Shaw cell. It is shown that the presence of surfactants can have both a stabilizing and a destabilizing effect on the shape of the drop, depending on the Bond number, the magnitude of the initial perturbation, and the strength of surface convection. Similar to the clean drop dynamics, two marginally stable branches are found. Increasing the surface Peclet number results in the stabilization of the main branch while the secondary branch shifts to higher Bond numbers. The mode of breakup is also found to be strongly influenced by the strength of surface convection.     

Interactions between cationic starch and anionic surfactants

The surface tensions and the phase equilibria of dilute aqueous cationic starch (CS)/surfactant systems were investigated. The degree of substitution of the CS varied from 0.014 to 0.772. The surfactants investigated were sodium dodecyl sulphate (SDS), potassium octanoate (KOct), potassium dodecanoate (KDod) and sodium oleate (NaOl). The concentrations of CS were 0.001, 0.01 and 0.1 w%.Critical association concentrations (cac) occur at surfactant concentrations well below the critical micelle concentrations of the surfactants, except for KOct, KDod and NaOl at the lowest CS concentrations investigated (0.001 w%). The surface tensions of CS/surfactant solutions decrease strongly already below the cac. This is attributed to the formation of surface active associates by ion condensation. Associative phase separation of gels formed by CS and surfactant takes place at extremely low concentrations when the surfactant/polymer charge ratio is somewhat larger than 1. The gel is higly viscous and contains 40–60% water, depending on the concentration of electrolyte, the surfactant hydrocarbon chain length and the nature of the polar head of the surfactant.The concentration at which the phase separation occurs decreases with increasing surfactant chain length and the concentration of simple electrolyte, factors that promote micelle formation. This indicates that the gels are formed by association of CS to surfactant micelles. When surfactant well in excess of charge equivalence is added, the gels dissolve because the CS/surfactant complexes acquire a high charge.     

An infrared study of adsorption of para-nitrophenol on mono-, di- and tri-alkyl surfactant intercalated organoclays

Infrared spectroscopy has been used to study the adsorption of para-nitrophenol on mono-, di- and tri-alkyl surfactant intercalated montmorillonite. Organoclays were obtained by the cationic exchange of mono-, di- and tri-alkyl chain surfactants for sodium ions [hexadecyltrimethylammonium bromide (HDTMAB), dimethyldioctadecylammonium bromide (DDOAB), methyltrioctadecylammonium bromide (MTOAB)] in an aqueous solution with Na-montmorillonite. Upon formation of the organoclay, the properties change from strongly hydrophilic to strongly hydrophobic. This change in surface properties is observed by a decrease in intensity of the OH stretching vibrations assigned to water in the cation hydration sphere of the montmorillonite. As the cation is replaced by the surfactant molecules, the para-nitrophenol replaces the surfactant molecules in the clay interlayer. Bands attributed to CH stretching and bending vibrations change for the surfactant intercalated montmorillonite. Strong changes occur in the HCH deformation modes of the methyl groups of the surfactant. These changes are attributed to the methyl groups locking into the siloxane surface of the montmorillonite. Such a concept is supported by changes in the SiO stretching bands of the montmorillonite siloxane surface. This study demonstrates that para-nitrophenol will penetrate into the untreated clay interlayer and replace the intercalated surfactant in surfactant modified clay, resulting in the change of the arrangement of the intercalated surfactant.     

The leading edge of evaporating droplets

New experiments on drops evaporating in normal atmosphere from smooth substrates in the situation of complete wetting are reported and compared with the available theoretical model. They are the continuation of previous work with alkane or water sessile drops, which is first briefly summarized. The model accounts very well for the dynamics of the drop radius, but the predictions are only qualitative for the contact angle, especially for small angles. Experiments with hanging drops allow us first to discard any influence of convection in the gas phase on the drops dynamics. Then the main part of the paper concerns new experiments with polydimethylsiloxane oligomers. These silicone oils are similar to alkanes as far as evaporation rate is concerned, but have lower surface tensions, and therefore smaller dynamic contact angles. The purity of the oils appears to be critical for the experiments, and requires a preliminary investigation. Then a systematic study of the drops dynamics is presented, as a basis for forthcoming theoretical work.     

表面活性剂亲水-亲油能力对动态界面张力的影响

当两个不互溶的液相接触时,如果其中一相或两相含有表面活性物质,就可能产生动态界面张力。两相间的界面张力随时间连续变化,直到平衡为止。在到达平衡的过程中,经常通过一个最低值。酸性油／碱水体系也会出现类似现象。Englind和Berg把动态界面张力解释为表面活性物质在界面上累积的结果,并观察到1,5－戊二醇由白油向水中传质时存在明显的吸附－脱附位垒。Rubin和Radke首次给出了解释酸性原油与碱水溶液接触时产生动态界面张力的物理模型,他们提出在油水上存在一个表面活性物质的脱附位垒,原油中的酸性物质与氢氧化钠在界面上的反应是迅速完成的,而这些物质的脱附,则比较缓慢,从而合理地解释了这一特征。近年来,由于超低界面张力在强化采油中的重要性,国外研究者对酸性油／碱／表面活性剂体系的动态界面张力特征进行了比较系统的研究,但其机理有待进一步探讨,本文通过对正构烷烃／石油磺酸盐体系动态界面张力的研究,考察了吸附－脱附位垒产生的原因、影响因素及其对动态界面张力曲线的影响,对酸性油／表面活性剂体系动态界面张力的机理进行了更深入的探索。     

表面活性剂亲水-亲油能力对动态界面张力的影响

当两个不互溶的液相接触时 ,如果其中一相或两相含有表面活性物质 ,就可能产生动态界面张力 .两相间的界面张力随时间连续变化 ,直到平衡为止 .在到达平衡的过程中 ,经常通过一个最低值 .酸 性油 /碱水体系也会出现类似现象 .England和 Berg[1]把动态界面张力解释为表面活性物质在界面上累积的结果 ,并观察到 1,5-戊二醇由白油向水 中传质时存在明显的吸附-脱附位垒 .Rubin和 Radke[2]首次给出了解释酸性原油与碱水溶液接触时产生动态界面张力的物理模型 ,他们提出在油水界面上存在一个表面活性物质的脱附位垒 ,原油中的酸性物质与氢氧化…     

Stretching liquid bridges with bubbles: the effect of air bubbles on liquid transfer

Liquid bridges containing bubbles are relevant to industrial printing and are also a topic of fundamental scientific interest. We use flow visualization to study the stretching of liquid bridges, both with and without bubbles, at low capillary numbers. We find that whereas the breakup of wetting fluids between two identical surfaces is symmetric about the bridge midpoint, contact line pinning breaks this symmetry at slow stretching speeds for nonwetting fluids. We exploit this observation to force air bubbles selectively toward the least hydrophilic plate confining the liquid bridge.