On The Way to Fe–C60 Compounds

Iron: fullerides were prepared by chemical methodes in the solution using nitric acid as activation agent. Experimental results of thermal analyses, X-ray diffraction and Mössbauer spectroscopy of the products are presented. To interpret these results, standard quantum chemistry calculations were used to determine the geometry and charge distribution in Fe:C₆₀ complexes, which might be formed in the reaction.     

Nd34Fe60O6合金的显微组织研究

采用扫描电镜、俄歇探针、Ｘ射线衍射、热磁分析、热磁分析等方法深入研究了Ｎｄ３４Ｆｅ６０Ｏ６合金的显微组织。发现合金的平衡组织由Ｎｄ２Ｆｅ１７主相、含氧的富钕相和一个Ｎｄ－Ｆｅ－Ｏ三元铁磁性相（记为Ｔ１相）组成。该相在８４０℃通过Ｎｄ２Ｆｅ１７相与富Ｎｄ液相的包晶反应形成。它的成分约为Ｎｄ３４Ｆｅ５０Ｏ１０，居里温度为１８０℃。其Ｘ射线衍射峰可用点阵常数α＝０．７７１ｎｍ、ｃ＝２．２２８ｎｍ的四方晶     

多晶Fe60Ni40合金阳极钝化膜的XPS研究

过渡金属Fe、Ni或其合金由于它们具有磁性和在工业上被用作催化剂等，它们与氧化腐蚀性气体02、C12等的作用已被广泛研究［‘－3］．含Ni的不锈钢和含Ni50％的FeNi基合金在酸性溶液中表现出比铁更好的耐腐蚀性并增强了氧化钝化层的附着力，放它们在溶液的腐蚀与钝性研究已引起广泛的兴趣，甚至包括对F6Ni基非晶合全玻璃的腐蚀与钝性研究【4一刊，用不同的方法研究溶液状态下的自然氧化膜或阳极钝化膜，得出的结果不同，对腐蚀与钝性解释也很不一致，硼酸一础砂或磷酸一磷酸盐缓冲液在工业上被广泛用作清洗剂、缓蚀剂或成膜剂等·因此，…     

Nd60Fe20Al10Co10非晶粉末晶化过程及动力学研究

利用机械合金化制备出Nd60Fe20Al10Co10非晶粉末,采用示差扫描量热仪(DSC),X射线衍射(XRD)和振动样品磁强计(VSM)考察了Nd60Fe20Al10Co10非晶的晶化转变过程及其对磁性能的影响规律,用Kissinger方程计算了Nd60Fe20Al10Co10的晶化激活能,从晶化动力学的角度讨论了玻璃形成能力与晶化反应速率常数的关系。结果表明,Nd60Fe20Al10Co10合金的晶化过程为:非晶+α Fe→非晶+α Fe+Nd→非晶+α Fe+Nd+未知相Mx→α Fe+Nd+未知相Mx+Co2Nd+AlCo。晶化激活能E约为173kJ·mol-1。非晶相的的弛豫无序结构是Nd60Fe20Al10Co10具有硬磁性的原因。完全晶化后硬磁性迅速消失。     

Studies on the Electronic Structures of the C_60, C_60H_60 and C_60F_60

The present paper represents the electronic structures of the cluster C60 and its derivatives C60H60 and C60F60 with FOOT-type of structure. On the basis of the total energies and molecular orbital energies from CNDO/2 calculations the clusters' stabilities, electronic configurations and charge distributions are discussed. The calculation results and discussion are very beneficial to understanding physical and chemical properties of the cluster C60 and its derivatives.     

[(CO)2(C5H5)Fe]2C60的合成与表征

有关 C6 0 取代的金属羰基化合物的研究方兴未艾 .C6 0 作为一个特殊的烯烃 ,以六元环间的碳碳双键提供电子对 ,与过渡金属羰基化合物形成诸如 η2 ,η4 ,η6等结构新颖的化合物约有 40多例 [1～ 5] ,但只有一例是以 Fe为中心原子的 C6 0 取代的金属羰基化合物 ( η2 - C6 0 ) Fe( CO) 4 [1] .本文报道了第一例 C6 0配位的 Fe的双核金属羰基化合物 [( CO) 2 ( C5H5) Fe]2 (η2 - C6 0 ) ,并通过元素分析 ,IR,1H NMR,13CNMR和 XPS进行表征 .1　实验部分[Fe( CO) 2 ( C5H5) ]2 购自 Aldrich公司 .C6 0 纯度为 99% .其余试剂均…     

Fe－ZSM－5分子筛中Fe的化学环境研究

本文应用ＥＳＲ、ＸＰＳ、ＤＲＳ、Ｍｏｓｓｂａｕｅｒ谱和首次运用ＴＰＲ技术结合ＸＰＳ、ＸＲＤ对Ｆｅ－ＺＳＭ－５中Ｆｅ的化学环境进行了研究。结果表明，碱性介质条件下合成的Ｆｅ－ＺＳＭ－５分子筛中，铁仅有一种价态Ｆｅ（Ⅲ），但却有多种存在形式。非骨架Ｆｅ（Ⅲ）包括分子筛孔道内及外表面上沉积的氧化铁；骨架Ｆｅ至少有两种状态，即骨架不饱和配位Ｆｅ（Ⅲ）和骨架畸变四配位的Ｆｅ（Ⅲ）．各种测试方法的结果表明Ｆｅ主要位于分子筛的骨架上，非骨架Ｆｅ（Ⅲ）很少．     

EDXRF方法在测量含水Fe样中Fe含量的应用

介绍了能量色散X荧光分析方法在含水Fe样品测量中的应用。用ANTG 2000型海底X荧光探测系统对含Fe为10%～60%的Fe样进行测量,建立水分对Fe元素特征Kα射线影响的校正模型。结果表明,通过该模型校正,对含饱和水情况下Fe样品的分析相对误差小于4%,具有良好的分析效果。     

嵌入纳米Fe颗粒的Fe液凝固过程的分子动力学模拟

采用Sutton-Chen 势函数及分子动力学(MD)方法对嵌入了Fe纳米团簇(半径从0.4-1.8 nm)的Fe液凝固过程进行了模拟. 模拟结果表明只有当嵌入的纳米团簇半径超过0.82 nm才能降低凝固时所需要的临界过冷度(ΔT^*), 起到诱导凝固的作用. 同时采用原子键型指数法(CTIM-2)对样本在凝固过程中的原子结构进行了标定, 通过观察微观结构演变发现当嵌入纳米团簇能够作为凝固核心时, 体系按照hcp-fcc 交叉形核的方式长大. 同时还发现嵌入纳米团簇对体系凝固过程晶核的生长方向及凝固的最终构型存在“结构遗传效应”.     

Fe—ZSM—5分子筛中Fe的化学环境研究

本文应用ＥＳＲ、ＸＰＳ、ＤＲＳ、Ｍｏｓｓｂａｕｅｒ谱和首次运用ＴＰＲ技术结合ＸＰＳ、ＸＲＤ对Ｆｅ－ＺＳＭ－５中Ｆｅ的化学环境进行了研究。结果表明，碱性介质条件下合成的Ｆｅ－ＺＳＭ－５分子筛中，铁仅有一种价态Ｆｅ（Ⅲ），但却有多种存在形式。非骨架Ｆｅ（Ⅲ）包括分子筛孔道内及外表面上沉积的氧化铁；骨架Ｆｅ至少有两种状态，即骨架不饱和配位Ｆｅ（Ⅲ）和骨架畸变四配位的Ｆｅ（Ⅲ）．各种测试方法的结果表明Ｆｅ主要位于分子筛的骨架上，非骨架Ｆｅ（Ⅲ）很少．     

含铁化合物的Fe2p和Fe3s电子能谱研究

选择了十几种常见的含铁化合物,分另采集了它们的Fe2p和Fe3s谱。从峰位和峰形上讨论了它们各自的特点,结果表明Fe2p和Fe3s峰的峰形分析（如,shake-up卫星峰及多重分裂峰）像其结合能值一样可以提供化学状态分析的重要信息。     

Influence of Fe concentration on the properties of the electrodeposited Zn–Fe coatings

Electrodeposition of Zn–Fe alloys on a copper substrate from a sulfate bath with different Fe²⁺ concentration (0.05, 0.10 and 0.20 mol L^?1) at room temperature was investigated using cyclic voltammetry. The influence of the Fe²⁺ content in the plating bath on the surface morphology, structural and magnetic properties of the coatings were characterized using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and Vibrating Sample Magnetometer (VSM). The results show that the morphology of Zn–Fe films changes with different Fe²⁺ concentration. The EDS analysis demonstrated that the Fe content of the coatings increased with increasing the Fe concentration in the bath. XRD measurements shows the presence of ?Zn (hcp), δ1ZnFe (hcp) and the ΓZnFe (bcc) phases with a (101) preferential orientation in all the electrodeposited films. The magnetic analysis of Zn–Fe films indicated that the saturation magnetization was largely enhanced in comparison to pure Zn, especially with 0.2 at. % Fe, while the coercivity decreased.     

流动注射分光光度法同时测定Fe(Ⅱ)和Fe(Ⅲ)

将流动注射技术引入邻菲罗啉分光光度法测定Fe2+分析体系,采用单阀双带镀镉锌片还原柱带隔离的阀体流路,建立了同时测定微量Fe2+和Fe3+的分析方法。Fe2+的测定范围为0~10 mg/L,检出限为1.2×10-6mg/L;Fe3+的测定范围为0~12 mg/L,检出限为1.8×10-6mg/L。方法用于水中Fe2+和Fe3+的同时测定。     

n-InP在Fe3+/Fe2+溶液中复阻抗的计算机拟合分析

本文测定了不同电位及不同光强下, n-InP在Fe~(3+)/Fe~(2+)溶液中的复阻抗图, 从一个等放电路用计算机对结果进行了拟合, 并对拟合结果进行了讨论。     

High-performance Fe–Co-based SOFC cathodes

With the aim of reducing the temperature of the solid oxide fuel cell (SOFC), a new high-performance perovskite cathode has been developed. An area-specific resistance (ASR) as low as 0.12 Ωcm² at 600 °C was measured by electrochemical impedance spectroscopy (EIS) on symmetrical cells. The cathode is a composite between (Gd_0.6Sr_0.4)_0.99Fe_0.8Co_0.2O_3-δ (GSFC) and Ce_0.9Gd_0.1O_1.95 (CGO10). Examination of the microstructure of the cathodes by scanning electron microscopy (SEM) revealed a possibility of further optimisation of the microstructure in order to increase the performance of the cathodes. It also seems that an adjustment of the sintering temperature will make a lowering of the ASR value possible. The cathodes were compatible with ceria-based electrolytes but reacted to some extent with zirconia-based electrolytes depending on the sintering temperature.     

A structural and Mössbauer study of complexes with Fe(2)(micro-O(H))(2) cores: stepwise oxidation from Fe(II)(micro-OH)(2)Fe(II) through Fe(II)(micro-OH)(2)Fe(III) to Fe(III)(micro-O)(micro-OH)Fe(III)

Dinuclear non-heme iron clusters containing oxo, hydroxo, or carboxylato bridges are found in a number of enzymes involved in O(2) metabolism such as methane monooxygenase, ribonucleotide reductase, and fatty acid desaturases. Efforts to model structural and/or functional features of the protein-bound clusters have prompted the preparation and study of complexes that contain Fe(micro-O(H))(2)Fe cores. Here we report the structures and spectroscopic properties of a family of diiron complexes with the same tetradentate N4 ligand in one ligand topology, namely [(alpha-BPMCN)(2)Fe(II)(2)(micro-OH)(2)](CF(3)SO(3))(2) (1), [(alpha-BPMCN)(2)Fe(II)Fe(III)(micro-OH)(2)](CF(3)SO(3))(3) (2), and [(alpha-BPMCN)(2)Fe(III)(2)(micro-O)(micro-OH)](CF(3)SO(3))(3) (3) (BPMCN = N,N'-dimethyl-N,N'-bis(2-pyridylmethyl)-trans-1,2-diaminocyclohexane). Stepwise one-electron oxidations of 1 to 2 and then to 3 demonstrate the versatility of the Fe(micro-O(H))(2)Fe diamond core to support a number of oxidation states with little structural rearrangement. Insight into the electronic structure of 1, 2', and 3 has been obtained from a detailed M?ssbauer investigation (2' differs from 2 in having a different complement of counterions). Mixed-valence complex 2' is ferromagnetically coupled, with J = -15 +/- 5 cm(-)(1) (H = JS(1).S(2)). For the S = (9)/(2) ground multiplet we have determined the zero-field splitting parameter, D(9/2) = -1.5 +/- 0.1 cm(-)(1), and the hyperfine parameters of the ferric and ferrous sites. For T < 12 K, the S = (9)/(2) multiplet has uncommon relaxation behavior. Thus, M(S) = -(9)/(2) <--> M(S) = +(9)/(2) ground state transition is slow while deltaM(S) = +/-1 transitions between equally signed M(S) levels are fast on the time scale of M?ssbauer spectroscopy. Below 100 K, complex 2' is trapped in the Fe(1)(III)Fe(2)(II) ground state; above this temperature, it exhibits thermally assisted electron hopping into the state Fe(1)(II)Fe(2)(III). The temperature dependence of the isomer shifts was corrected for second-order Doppler shift, obtained from the study of diferrous 1. The resultant true shifts were analyzed in a two-state hopping model. The diferric complex 3 is antiferromagnetically coupled with J = 90 +/- 15 cm(-)(1), estimated from a variable-temperature M?ssbauer analysis.     

Nd60Fe20Al8Co10B2大块非晶合金晶化过程中的结构及磁性能变化

利用吸铸的方法制备了Nd60Fe20Al8Co10B2大块非晶合金。采用示差扫描量热法(DSC)，X射线衍射(XRD)，扫描电子显微镜(SEM)和振动样品磁强计(VSM)研究了Nd60Fe20Al8Co10B2大块非晶合金在晶化过程中的微观结构及磁性能的变化情况。Nd60Fe20Al8Co10B2大块非晶合金在低于723K退火时，富Nd相和富Fe相的析出对于合金的矫顽力影响不大。但是，富Fe相的长大使合金的饱和磁化强度和剩磁下降明显。合金完全晶化后，硬磁性迅速消失。     

滴定计算分析法同时测定Fe(Ⅲ)与Fe(Ⅱ)的研究

以铂电极为指示电极,Ce^4 标准溶液为滴定剂,对氧化还原滴定计算分析法同时测定Fe(Ⅲ)与Fe(Ⅱ)进行了研究。导出了同时测定Fe(Ⅲ)与Fe(Ⅱ)的滴定计算式。结果表明,电极的系统误差是影响测定结果准确度的主要因素,而且系统误差对Fe(Ⅲ)的影响比较大,对Fe(Ⅱ)的影响比较小。用刚开始滴定的实验数据,Fe(Ⅲ)的误差比较小;用接近化学计量点的实验数据,Fe(Ⅱ)的误差比较小。