Detection of four different OH-groups in ground kaolinite with controlled-rate thermal analysis

The thermal behaviour of mechanochemically treated kaolinite has been investigated under dynamic and controlled rate thermal analysis (CRTA) conditions. Ten hours of grinding of kaolinite results in the loss of the d(001) spacing and the replacement of some 60% of the kaolinite hydroxyls with water. Kaolinite normally dehydroxylates in a single mass loss stage between 400 and 600°C. CRTA technology enables the dehydroxylation of the ground mineral to be observed in four overlapping stages at 385, 404, 420 and 433°C under quasi-isobaric condition in a self-generated atmosphere. It is proposed that mechanochemical treatment of the kaolinite causes the localization of the protons when the long range ordering is lost.This revised version was published online in November 2005 with corrections to the Cover Date.     

Effect of thermal history on crystallization and melting behaviour of lldpe

In this paper two LLDPE samples with their own structural parameters were studied by means of DSC. Experimental results show that DSC was good for revealing slight structural difference between these two samples. Furthermore, the effect of thermal history on crystallization and melting behaviour of LLDPE was observed clearly through varying conditions of thermal treatment.

---

Zusammenfassung Mittels DSC werden zwei LLDPE-Proben mit ihren eigenen Strukturparametern untersucht. Die Versuchsergebnisse zeigen, da\ sich DSC gut eignet, um gering fügige Unterschiede dieser zwei Proben nachzuweisen. Weiterhin wurde unter verschiedenen Bedingungen der Einflu\ der thermischen Vorgeschichte auf das Kristallisations-und Schmelzverhalten von LLDPE untersucht.

     

About the synthesis and thermal stability of SiO2-aerogel

Aerogels are extremely porous high-tech materials based on inorganic oxides, especially silica. The paper describes synthesis and properties of SiO₂-aerogel, and changes occurring during heating of SiO₂-aerogel in the temperature range from 20 to 1000°C. Four thermoanalytical methods were used: Thermodilatometry, Differential thermal analysis, Thermogravimetry and Derivative thermogravimetry.     

A kinetic study on the thermal behaviour of chitosan

The thermal behaviour of chitosan was studied by means of thermogravimetry, mass spectrometry and infrared spectrometry. Kinetic parameters were obtained by advanced kinetic evaluation (differential isoconversional analysis) from DSC curves, in non-isothermal conditions, at several heating rates, between 5 and 30°C min⁻¹. The results showed that the decomposition of chitosan does not follow a single mechanism because both the activation energy and the pre-exponential factor are not constant during the course of the reaction. A comparison with the results obtained by applying different conventional calculating methods is also shown.     

DTA investigation of thermal dissociation of the solid system CuCl2−KCl

Solid mixtures of CuCl₂ and KCl were annealed at 473 K for different times, then cooled down to room temperature and thermogravimetrically analysed. The differences in the DTA pictures of the samples were analysed. Conclusions were drawn as concerns the solid and liquid states of the mixtures.     

二氧化硅气凝胶在保温隔热领域中的应用

二氧化硅(SiO_2)气凝胶是通过使用气体来置换湿溶胶中的液体,从而得到一种结构可控的新型轻质纳米多孔固态材料.SiO_2气凝胶材料与其他保温隔热材料相比,具有较低的导热系数(≈0.013 W/(m·K))和较高的透明性,在保温隔热领域中开发潜力巨大,有望替代传统的保温隔热材料.尽管气凝胶目前的成本高于传统的隔热材料,但是我们相信通过科学家和工程学家的不断努力,气凝胶的生产成本会被不断的降低,最终遍及世界各地.本文作者综述了SiO_2气凝胶材料在隔热领域的多种应用形式,介绍了目前国内外气凝胶公司研发产品情况以及实际应用案例.     

Composition and thermal stability of SiO2-based hybrid materials TEOS-MTEOS system

Hybrid materials with different amounts of organics permanently bound on the inorganic network obtained in the TEOS-MTEOS (tetraethoxysilan-methyltriethoxysilan) system are used for obtaining coatings with different optical and mechanical properties. To study the thermal stability of the mentioned materials, compositions with different molar ratios of the precursors were prepared. The influence of the solvent and water amounts on the gelation process was also investigated. The gels obtained were characterised by IR spectrometry and their decomposition temperatures were determined by DTA/TG. Thermal stability of the gels is rather influenced by their composition than the conditions of the gelation process. This revised version was published online in July 2006 with corrections to the Cover Date.     

尼龙6/SiO_2纳米复合材料的制备及其力学性能和热稳定性

以表面含有氨基的可反应性纳米SiO2(RNS-A)和表面含有烷基碳链的可分散性纳米SiO2(DNS-3)作为填料,利用原位聚合法制备了尼龙6/SiO2纳米复合材料(相应的复合材料分别简记为RPA和DP3);采用透射电子显微镜观察了复合材料中纳米SiO2的表面形貌,并利用热失重分析仪测定了复合材料的热稳定性,进而考察了纳米SiO2表面功能基团对尼龙6力学性能和热稳定性的影响.结果显示,纳米SiO2能够很好地分散在尼龙6基体中,并使尼龙6的热分解温度提高10℃左右.与此同时,RPA的最大拉伸强度和冲击强度较纯尼龙6的分别提高34.5%和12.5%,DP3的最大拉伸强度和冲击强度分别提高18.2%和45.7%.这表明两种纳米SiO2均可以有效地提高尼龙6的力学性能和热稳定性;可以推测,纳米SiO2的增强效应与其在尼龙6基体材料中的分散和界面作用有关.     

The thermal transformation of an aromatic poly (amide), poly (ortho-oxyamide) and poly (benzoxazole)

The thermal behaviour of three aromatic polymers, poly(3,3-dioxy-4,4-diphenylmethane) (POA), poly(2,2-m-phenylene-5,5-dibenzoxazolemethane) (PBO) and a commercial poly-(phenyleneisophthalamide) (Phenylon) was studied by thermal analysis, i.e. DSC and TG. PBO was formed by the progressive thermocyclization of POA. By transforming POA into PBO the thermal stability was increased proportionally to the degree of cyclization, due to the stiffening of the polymer chain. PBO was found to be more thermally stable than Phenylon. The activation energies of the desorption of moisture, cyclization and thermal degradation of the polymers in both nitrogen and air were determined from non-isothermal TG data.     

Effect of accelerated thermal ageing on the thermal behaviour of the recently made parchments

To reveal the fire injuring of parchment, the changes in the thermal behaviour of some goat parchments, obtained from skins originating from different animals, as a result of thermal aging were determined by thermal analysis methods (DSC; simultaneous TG/DTG, DSC; micro hot table (MHT)). Thermal aging of parchments was revealed to bring about the decrease in shrinkage temperature, absolute value of enthalpy of denaturation in water and some changes in non-isothermal parameters characteristic for dehydration process in static air atmosphere. The results obtained by DSC analysis performed in N₂ and O₂ flows as well as those obtained by simultaneous TG/DTG, DSC analyses have shown that both softening (melting) process parameters and parameters of thermo-oxidative processes have not been changed by thermal ageing. The results obtained by thermal analysis methods were correlated with those obtained by microscopic investigation of parchment samples immersed in water and scanning electron microscopy (SEM). The application of these microscopic techniques has revealed the morphology changes in the investigated parchments as a result of thermal degradation.     

Precision ADMET polyolefins containing dithiane: Synthesis,thermal properties,and macromolecular transformation

1,3‐Dithiane and its derivatives are widely used as powerful acyl anion equivalent to a range of useful transformations that are needed in the synthesis of natural products. In this work, a series of polyolefins containing pendant dithiane groups have been designed and synthesized via acyclic diene metathesis polymerization (ADMET) polymerization and subsequent hydrogenation. The structures of these polymers were characterized by ¹H NMR, ¹³C NMR, and FT‐IR, and successful incorporation of the dithiane groups was proved. With different contents of the dithiane moieties, these ADMET polymers exhibited distinct thermal properties different from each other as evidenced by differential scanning calorimetry and thermal gravimetric analysis. The dithiane units in the ADMET polymer with 20 methylene carbons between the adjacent dithiane groups were transformed into thiol groups via reaction with Bu₃SnH. This work provided a convenient route to synthesize polyethylene with pendant thiol groups that are evenly distributed in the chain. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2468–2475     

DTA/DSC study of nanocrystallization in oxyfluoride glasses

Crystallization of glasses of the Na₂O-Al₂O₃-SiO₂-LaF₃ system was studied by DTA/DSC, XRD and TEM methods. It has been found that the nanocrystallization of LaF₃ in the NAS-based glass strongly depends on ratio of Na₂O/(SiO₂+Al₂O₃) and amount of doped LaF₃. Analysis of the local atomic interactions in the structure of oxyfluoride glasses has been used to explain the course of the crystallization. This revised version was published online in July 2006 with corrections to the Cover Date.     

Study of the reaction mechanism and composition analysis of multiple-component mixed minerals DTA/T/EGD/GC on-line coupled simultaneous technique

An established DTA/T/EGD/GC on-line coupled simultaneous technique and relevant equipment were applied to identify the micro impurity minerals—pyrite and siderite in two kinds of dolomite in air and N₂. The proportional five-component mixed minerals (siderite, kaolinite, dolomite, calcite and quartz) and the proportional six-component mixed minerals (pyrite and the above five minerals) were detected in N₂ and in air/CO₂ (1∶1) separately by applying DTA/EGD/GC and DTA/GC. The experimental results provide the basis for demonstration of the reaction mechanism of thermal decomposition of various gas—solid-phase minerals in N₂ and air/CO₂. The compositions of six-component mixed minerals can be distinguished individually from the DTA/GC curves; reliable results are obtained.     

热分解法制备的Co/SiO2催化剂上费-托合成反应性能

以无定形二氧化硅为载体,分别采用浸渍法和热分解法制备了钴基催化剂Co/A200-I和Co/A200-D,采用TG、XRD、TEM和TPR等手段对其进行了表征,并考察了这些催化剂在费-托合成反应中的性能。结果表明,浸渍法制备的Co/A200-I催化剂中钴颗粒没有规则的形状,但却具有较高的费-托合成反应活性;热分解法制备的Co/A200-D催化剂中钴颗粒呈一种球形二次结构,直径比较均匀,对于费-托合成反应具有较高的轻质烃选择性。此外,载体比表面积对催化剂结构也有较大的影响;相对于Co/A200-D催化剂,Co/A380-D催化剂的载体比表面积较大,这使得金属-载体间的相互作用较强而较难还原,但还原后Co/A380-D催化剂拥有较高的钴分散度和较好的反应活性     

The kinetic equation in the DTA study of the silica gel to cristobalite transformation

The importance of the choice of a suitable kinetic equation in the DTA study of the silica gel to cristobalite transformation is pointed out. It is shown that isothermal and non-isothermal data reported in the literature are better fitted by a Johnson-Mehl-Avrami equation withn=3, rather than a first-order one.

---

Zusammenfassung Die Bedeutung der Wahl einer entsprechenden kinetischen Gleichung bei der DTA-Untersuchung von Kieselgel zur Cristobalittransformation wurde aufgezeigt. Es wurde bewiesen, daß isotherme und nichtisotherme Angaben der Literatur durch eine Johnson-Mehl-Avrami-Gleichung mit n=3 besser interpoliert werden können als durch eine Gleichung »erster Ordnung«.

---

Résumé On souligne l'importance du choix d'une équation cinétique convenable lors de l'étude par ATD de la transformation du gel de silice en cristobalite. On montre que les résultats cités dans la littérature obtenus en régimes isothermes et non-isothermes sont mieux interpolés par l'équation de Johnson-Mehl-Avrami avecn=3 que par une équation du «premier ordre».

---

. , , , -- =3, « ».

     

X-ray study of the thermal intercalation of alkali halides into kaolinite

Intercalation complexes of kaolinite with a series of alkali halides (NaCl (trace amounts), KCl, RbCl, CsCl, NaBr, KBr, CsBr, Kl, Rbl and Csl) were obtained by a thermal solid state reaction between the kaolinite-dimethylsulfoxide intercalation complex and the appropriate alkali halide. The ground mixtures (11 weight ratio) were pressed into disks that were gradually heated up to 250 °C for different times. X-ray diffractograms of the disks were recorded after each thermal treatment. At the end of the thermal treatment the disks were ground and basal spacings of the powders obtained. As a result of thermal treatment, alkali halide ions diffuse into the interlayers, replacing the intercalated dimethylsulfoxide molecules. Such a replacement may take place only if the thermal diffusion of the penetrating species is faster than the evolution of the intercalated organic molecule. With increasing temperature the intercalated salt diffused outside the interlayer space or underwent a thermal hydrolysis which resulted in the evolution of hydrogen halides from the interlayer space. Consequently, the amounts of intercalation complexes decreased at elevated temperatures.     

Synthesis,characterization and thermal behaviour of solid 2-methoxybenzoates of trivalent metals

Solid-state Ln(L)₃ compounds, where Ln stands for trivalent Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu and Y and L is 2-methoxybenzoate have been synthesized. Simultaneous thermogravimetry and differential thermal analysis (TG-DTA), differential scanning calorimetry (DSC), X-ray powder diffractometry, infrared spectroscopy and complexometry were used to characterize and to study the thermal behaviour of these compounds. The results provided information on the composition, dehydration, coordination mode, structure, thermal behaviour and thermal decomposition.     

TG-MS,TG, DTG and DTA methods in study of thermal decomposition of some d-metal complexes with 4,4'-bpy and propionates

The new mixed ligand complexes with formulae M(4-bpy)(C₂H₅COO)₂·2H₂O (where M(II)=Mn, Co, Ni; 4,4'-bpy or 4-bpy=4,4'-bipyridine) and Cu(4-bpy)_0.5(C₂H₅COO)₂·H₂O were prepared and characterized by VIS (for solid compounds of Co(II), Ni(II), Cu(II) in Nujol), IR spectroscopy, X-ray powder diffraction and molar conductance in MeOH, DMF or DMSO. Thermal behaviour of complexes was studied under static conditions in air atmosphere. Corresponding metal oxides were identified as final products of pyrolysis. A coupled TG-MS system was used to analysis of principal volatile thermal decomposition and fragmentation products of isolated complexes under dynamic air and argon atmosphere. The principal species correspond to: C⁺, OH⁺, H₂O⁺, NO⁺, CO₂ ⁺ and other; additionally CO⁺ in argon atmosphere. This revised version was published online in July 2006 with corrections to the Cover Date.     

Raman study of TiO2 role in SiO2-Al2O3-MgO-TiO2-ZnO glass crystallization

Tough glass-ceramic material of special mechanical properties with nanosize crystal phases formed by appropriately controlled crystallization was studied by Raman spectroscopy. It was obtained by TiO2 activated crystallization of Mg-aluminosilicate glass of SiO2-Al2O3-MgO-TiO2-ZnO composition. Crystallization was preceded by a change in the TiO2 structural position and state, which is manifested by a changed color of glass from yellow into blue shortly before the glass transformation (Tg) temperature. Raman spectroscopy was applied to explain the mechanism of this process and to establish the role of TiO2 in the early stage of glass crystallization that precedes a complete crystal phase formation. The starting glasses were found in almost complete disorder, since all bands were weak, broad and dominated by a Bose band at about 90 cm-1. After the sample annealing all bands turned out better resolved and the Bose band practically disappeared, both confirming the amorphous structure reorganization process. A multiplet observed in the vicinity of 150 cm-1 we assigned to the anatase and other titania structures that can be considered prime centers of crystallization. Finally, in the closest neighborhood of the Rayleigh line the low frequency mode characterizing nanoparticles was observed. According to this band theory, the mean size of initial titania crystallites is about 10nm for all samples, but the size distribution varies within factor two among them.     

About the kinetic equation in the DTA study of the silica gel to cristobalite transformation

The method suggested by Marotta and Buri for performing the kinetic analysis of the silica gel to cristobalite transformation from the DTA trace is criticized. It is shown that this method does not allow determination of the value of the exponentn in the Avrami-Erofeev law. This is in contradiction with the theoretical deduction made by the above authors.