Interaction between indigo and adsorbed protein as a major factor causing backstaining during cellulase treatment of cotton fabrics

A model microassay system was developed to measure indigo backstaining on cotton fabrics in the presence of enzymes on a small laboratory scale. Backstaining indexes for 11 cellulase samples were measured, and the enzymes were ranked from lower to higher backstaining. Two multienzyme cellulase preparations were separated into fractions using chromatofocusing on a Mono P column. Adsorption ability and backstaining properties of purified enzyme fractions were studied. Evidence was obtained that protein adsorption on cotton fabrics is a crucial parameter causing backstaining (both for crude cellulase samples and purified enzyme components).     

Action of a finishing product in the improvement of the ultraviolet protection provided by cotton fabrics. Modelisation of the effect

The Ultraviolet Protection Factor of a fabric is a quantitative measurement of the effectiveness of the fabric to protect the human skin against ultraviolet radiation. The protection provided by uncoloured cellulosic fabrics is, in general, too low, but can be improved by the finishing treatment with UV-absorbers. In the present paper cotton fabrics with different compactness, and hence with different initial Ultraviolet Protection Factor values, are treated with several concentrations of an UV-absorber, according to a predefined experimental plan. The influence of each variable as well as their interaction on the response of Ultraviolet Protection Factor is analysed and a statistical model for predictions is proposed.     

A new study of the enzymatic hydrolysis of carboxymethyl cellulose with a bulk acoustic wave sensor

A new bulk acoustic wave (BAW) cellulase sensing technique, which is based on the enzymatic hydrolysis process of sodium carboxymethylcellulose (CMC) by cellulase, was established. The frequency shift curves of BAW sensor indicated that the viscosity of the tested solutions decreased during the hydrolysis process. The hydrolysis rate of CMC by cellulase was calculated from the frequency shift curves. The hydrolysis rate of CMC under different pH conditions at 30°C showed that cellulase had high hydrolysis ability approximately at pH 5.0. Kinetic parameters (the Michaelis constant K_m and the maximum rate V_max) of the process were estimated by using a linear method of Lineweaver–Burk plot. K_m is 1.95±0.25 mg ml⁻¹ and V_max is −(4.25±0.58)×10⁻³ g^1/2 cm^−3/2 cP^1/2 min⁻¹. Also the activation energy (E_a) of the enzymatic hydrolysis, with a value of 51.99±1.26 kJ mol⁻¹, was estimated in this work.     

An extension of the Harano-Ooshima rate expression for enzymatic hydrolysis of cellulose to account for changes in the amount of adsorbed cellulase

Three empirical rate expressions, Kinetics I, II, and III, for the enzymatic hydrolysis of cellulose were evaluated in an effort to develop a easy-to-use rate expression. They are based on the following equation:-dV/dX = kV, where V and X are the hydrolysis rate and the fractional conversion. In Kinetic I,k is constant. In Kinetic II, a linear relatinship betweenk and t is assumed. In Kinetic III, an exponential relationship is assumed. The three expressions were applied to enzymatic hydrolysis carried out under seven different conditions in which the kinds of substrates, enzymes, and initial concentrations were varied. All of the examined rate expressions were applied to the hydrolysis with success, but the better accuracies were obtained by Kinetic III, Kinetic II, and Kinetic I in this order. The variations ofk with time found in this study, especially the exponential relationship, were consistent with the effect of the measured changes in the concentration of adsorbed enzyme as predicted by theory developed previously by Ooshima et al. (1).     

Functionalized mesoporous materials for adsorption and release of different drug molecules: A comparative study

The adsorption capacity and release properties of mesoporous materials for drug molecules can be improved by functionalizing their surfaces with judiciously chosen organic groups. Functionalized ordered mesoporous materials containing various types of organic groups via a co-condensation synthetic method from 15% organosilane and by post-grafting organosilanes onto a pre-made mesoporous silica were synthesized. Comparative studies of their adsorption and release properties for various model drug molecules were then conducted. Functional groups including 3-aminopropyl, 3-mercaptopropyl, vinyl, and secondary amine groups were used to functionalize the mesoporous materials while rhodamine 6G and ibuprofen were utilized to investigate the materials’ relative adsorption and release properties. The self-assembly of the mesoporous materials was carried out in the presence of cetyltrimethylammonium bromide (CTAB) surfactant, which produced MCM-41 type materials with pore diameters of ∼2.7-3.3 nm and moderate to high surface areas up to ∼1000 m²/g. The different functional groups introduced into the materials dictated their adsorption capacity and release properties. While mercaptopropyl and vinyl functionalized samples showed high adsorption capacity for rhodamine 6G, amine functionalized samples exhibited higher adsorption capacity for ibuprofen. While the diffusional release of ibuprofen was fitted on the Fickian diffusion model, the release of rhodamine 6G followed Super Case-II transport model.     

A comparative study of the bonding in different halides of iridium

X-ray photoelectron spectroscopy and multiple scattering Xα calculations have been applied to a series of iridium halide complexes in order to corroborate the nature of the bondings inherent in this class of compounds. Our results seem to substantiate contentiously that higher oxidation states of iridium favor the formation of covalent bonds. This conclusion is based on the observation that (1) successive bombardment of the iridium species by Ar ions almost definitely leads to a configuration in which iridium is bound to at most one halide ion, and (2) the theoretical charge per ligand ion approaches systematically a value of {1?} in the limit as the formal oxidation state of iridium approaches {1+}. The theoretical results are further arthenticated by the fact that the experimental ionization energy of the Ir(4f) level in the different iridium halide complexes studied is seen to decrease as a result of exposure to Ar ions.     

A comparative study for treatment of white liquor by different applications of Fenton process

In this paper, the treatability of white liquor by conventional (CFP), modified (MFP) and electro-Fenton oxidation processes (EFP) was investigated depending on the COD parameter. Based on the experimental results, up to 62.4%, 58.4% and 54.9% COD removals by the CFP, MFP and EFP were achieved, respectively. It was observed that adjustment of initial pH to acidic values is not required in the CFP. The optimal operational conditions were found to be [Fe²⁺] = 500 mg/L, [H₂O₂] = 1000 mg/L at pH 7.3 (original pH) in the CFP, [Fe⁰] = 1250 mg/L, [H₂O₂] = 1000 mg/L at pH 3 in the MFP, and I = 1.0 A, [H₂O₂] = 1500 mg/L at pH 3 in the EFP, respectively. As a result, the CFP has been determined as a more efficient alternative treatment method.     

A microcalorimetric study of the different states of argon and nitrogen adsorbed AT 77 K on silicalite-I and ZSM-5

The adsorption of argon and nitrogen on a series of MFI-type zeolites (silicalite-I (Si/Al>1000) and HZSM-5 (16相似文献   

A study on the effects of ozone treatment on the properties of raw and degummed mulberry silk fabrics

Ozone is a powerful oxidizing agent and is widely used in various applications, which includes bleaching of cotton. Its application on the processing of silk is non-existent. Research studies on degumming and bleaching of silk reveal that almost no work involving ozone has been carried out. Therefore a study was carried out to understand the effects of process parameters namely wet pickup, pH and time in the ozone treatment of raw and degummed mulberry and tassar silk fabrics on their properties. This paper reports on the effects of ozone treatment on the mulberry silk fabrics. The study was extended with a view to compare the ozone treatment with soap degumming and hydrogen peroxide treatment carried out on raw and degummed mulberry silk fabrics, respectively. The treatment results in increase in yellowness index and amino group content and decrease in breaking strength and elongation, weight and flexural rigidity. The results obtained are substantiated with tyrosine content, scanning electron micrographs and infrared spectroscopy of the treated materials. The effect of pH on the treatment is maximum up to pH 4 and then decreases. The treatment is more severe when the wet pickup used is 50% compared to that of 10 and 100%. With respect to treatment time, though the severity increases with time, it is maximum during the first 10 min of the treatment. Soap degumming of raw silk fabric results in lower yellowness index and flexural rigidity and lesser loss in breaking strength and elongation compared to that of ozone treated material. There is not much of difference between ozone and hydrogen peroxide treatments of degummed silk fabric except for the lower yellowness index obtained in the latter case.     

A comparative study of immobilization techniques for urease on glass-pH-electrode and its application in urea detection in blood serum

Different techniques have been used (physical adsorption, physically entrapped sandwich and microencapsulation) for the immobilization of urease enzyme in tetramethylorthosilicate (TMOS) derived sol-gel matrix on the sensing surface of glass-pH-electrode. No significant leaching of enzyme occurs from the microencapsulated and physically entrapped enzyme sandwich films. Potentiometric techniques have been used for the estimation of urea concentration in each instance. Various parameters of biosensor performance have been studied which indicates that microencapsulation technique is a better method of enzyme immobilization in sol-gel films derived from TMOS. The advantage of microencapsulated biosensor over others include higher sensitivity (dpH/dp(C) = 2.4), lower detection limit of 52 μg mL⁻¹, larger linear range (0.01-30 mM) of urea determination and reasonably long-term stability of about 25 days with 80% response signal.     

A comparative study of the silent discharge treatment of saturated and unsaturated hydrocarbon polymers

Dielectric barrier air discharge treatment of polyethylene, polypropylene, polyisobutylene, polystyrene, and polyisoprene substrates has been characterized by x-ray photoelectron spectroscopy (XPS). The relative reactivities of these polymers towards silent discharge oxidation are rationalized in terms of ozone molecules interacting with an excited surface. © 1994 John Wiley & Sons, Inc.     

Adsorption of carbon monoxide and oxygen on transition metal surfaces: A comparative study of the results from electron spectroscopy and theoretical calculations

Results of investigations on the adsorption of CO andO ₂ on transition metal surfaces by employinguv and x-ray photoelectron spectroscopy and electron energy loss spectroscopy (eels) are presented. Results of molecular orbital calculations on adsorbed CO and O₂ are also discussed. Some of the interesting aspects discussed are, satellites in the O(ls) region due to adsorbed CO, vibrationaleels of adsorbed O₂ and dissociation energy profiles of adsorbed O₂ on clean surfaces as well as surfaces covered with potassium or presorbed atomic oxygen. Contribution No 245 from the Solid State and Structural Chemistry Unit.     

A comparative study of the effects of different buffer gases on the line shape of water vapour rovibronic transition

The line shape parameters of water vapour rovibrational transition at 12145.444 cm⁻¹ belonging to the (2ν₁ + ν₂ + ν₃) overtone band in the presence of three buffer gases He, N₂ and CO₂ are studied by high resolution near infrared (NIR) diode laser spectrometer. The wavelength modulation spectroscopy (WMS) is adopted to probe buffer gas broadened first derivative (1f) signal of water vapour transition. The simulation of the experimental signals based on Voigt profile provides the collisional broadening coefficients and line strength parameters. The comparison is made between the broadening effects on water vapour transition induced by He, N₂ and CO₂.     

A comparative study of trace enrichment of chlorophenols in water by extraction with C6 and C8 alkanes and by C18 reversed-phase adsorption

The efficiency, reproducibility and sensitivity ofn-hexane and iso-octane extraction and of C₁₈ reversed-phase adsorption for accumulation of 4-chloro-, 2,4-dichloro-, 2,4,5- and 2,4,6-trichloro-, 2,3,4,6-tetrachloro- and pentachlorophenol from aqueous solutions were compared. In extraction procedures the acetyl and pentafluorobenzoyl derivatives of chlorophenols were extracted from water. In adsorption procedure chlorophenols adsorbed on a Sep-Pak C₁₈ cartridge were eluted with acetone and after that derivatized analogously.All three procedures were found to be applicable for an efficient trace enrichment of chlorophenols in water, the proper choice being dependent on the required sensitivity of the analysis. Lower detection limits of single compounds at 10 ng·1^–1 levels were achieved by adsorption procedure owing to the more uniform and for most chlorophenols higher adsorption than extraction recoveries as well as owing to the possibility of treating larger volumes of water samples. The extraction procedure could be successfully applied to the concentrations of chlorophenols in water 1g·1^–1.Owing to its higher efficiency and better sensitivity the C₁₈ reversed-phase adsorption procedure was chosen as the more suitable one for the determination of chlorophenol levels in surface, ground and drinking waters. The conversion of chlorophenols accumulated from a water sample parallel to both acetyl and pentafluorobenzoyl derivatives and the analysis of both types of derivatives on two basically different gas Chromatographic columns were recommended for a more reliable identification and quantitation of the compounds analyzed.     

A comparative study of the bonding in heteroatom analogues of benzene

Summary Inorganic benzenes X₃Y₃H₆ are investigated, with X and Y chosen from Zn, B, Al, Ga, C, Si, Ge, N, P, As, O, and S such that there are a total of 6 electrons. Geometries and bond orders are used to qualitatively assess the degree of aromatic bonding in these species. Bond orders are extracted from the CI density matrix over localized molecular orbitals, using methods pioneered by Ruedenberg. Second row elements C, N, O are found to be more effective at this bonding. The aromatic bonding is poorest when X and Y have a large electronegativity difference.Dedicated to Prof. Klaus Ruedenberg     

A comparative study on the mode of interaction of different nanoparticles during MALDI‐MS of bacterial cells

We propose the benefits of preincubation during nanoparticle‐assisted bacterial analysis, where the bacteria are grown along with the nanoparticles. We were able to obtain a two to ten fold enhancement of bacterial signals in 3 h compared to the generally used methodology followed in previous literature. The previous literature method required a long time (18 h) to obtain such an enhancement. We probe the interactions of two bacteria, Staphylococcus aureus and Pseudomonas aeruginosa, with Ag, NiO, Pt TiO₂ and ZnO nanoparticles via transmission electron microscopy, ultraviolet spectroscopy and matrix‐assisted laser desorption/ionization (MALDI) mass spectrometry (MS). Based on these results, we propose a mechanism for interaction of these five nanoparticles with bacteria. Two mechanisms were observed for the interactions: (1) Mechanism A is proposed for the Pt and NiO NPs which functioned based on affinity for bacterial cells. (2) Mechanism B was proposed for the bactericidal NPs such as TiO₂, ZnO and Ag NPs. The results indicate that the success of the unmodified NPs in MALDI‐MS bacterial studies lies in following the ideal protocol for incubation at the ideal concentrations. Copyright © 2013 John Wiley & Sons, Ltd.     

A comparative catalytic study using different metal ions by incorporating functionalized metallosalen into the lacunary position of Keggin polyoxometalate

A series of new hybrids, POM (M-Salen@POM) were synthesized by successfully inserting metallosalen compounds (where M ​= ​Co, Cu, Fe and Ru) into the lacunary position of Keggin type polyoxometalate, K₈SiW₁₁O₃₉ (POM). The hybrids were characterized by FT-IR, powder XRD, diffuse reflectance UV–Vis, energy dispersive X-Ray and inductively coupled plasma atomic emission spectroscopy (ICP) techniques. The hybrids with different metal centers were comparatively studied for their catalytic activity in the oxidation of cycloalkanes, cycloalcohols and alkyl aromatic using a green oxidant, hydrogen peroxide. The products obtained during catalysis were estimated by gas chromatography(GC) and mass spectroscopy(MS). Catalytically synthesized products are of high industrial importance.     

A comparative study of calibration transfer methods for determination of gasoline quality parameters in three different near infrared spectrometers

This work presents a comparative study of calibration transfer among three near infrared spectrometers for determination of naphthenes and RON (Research Octane Number) in gasoline. Seven transfer methods are compared: direct standardization (DS), piecewise direct standardization (PDS), orthogonal signal correction (OSC), reverse standardization (RS), piecewise reverse standardization (PRS), slope and bias correction (SBC) and model updating (MU). Two pre-treatment procedures, namely standard normal variate (SNV) and multiplicative scatter correction (MSC), are also investigated. The choice of an appropriate number of transfer samples for each technique, as well as the effect of window size in PDS/PRS and OSC components, are discussed. A broad set of gasoline samples representative of the Northeastern states of Brazil is employed in the investigation. The results show that the use of calibration transfer yields prediction errors comparable to those obtained with complete recalibration of the secondary instrument. Overall, the results point to RS as the best method for the analytical problem under consideration. When storage and/or physical transportation of transfer samples are impractical, MU is more appropriate. The comprehensive investigation carried out in the present work will be of value for practitioners involved in networks of fuel monitoring.     

A comparative study of the dehydroxylation process in untreated and hydrazine-deintercalated dickite

A dickite from Tarifa (Spain) was used to study the influence of the intercalation and the later deintercalation of hydrazine on the dehydroxylation process. The dehydroxylation of the untreated dickite occurs through three overlapping endothermic stages whose DTA peaks are centred at 586, 657 and 676°C. These endothermic effects correspond, respectively, to the loss of the inner-surface, the inner hydroxyl groups, and the loss of the water molecules, product of dehydroxylation process, which has been trapped in the framework of the dehydroxylated dickite. The intercalation of hydrazine in the interlayer space of dickite and the later deintercalation affect the dehydroxylation process. It occurs through only two endothermic stages which DTA peaks are centred at 575 and 650°C. The first corresponds to the simultaneous loss of both the inner and the inner-surface hydroxyl groups, whereas the second one is analogous to that at 676°C observed in the DTA curve of untreated dickite. These effects appear shifted to lower temperatures compared to those observed in the untreated dickite.