Photocatalytic properties of mesoporous TiO<Subscript>2</Subscript>/ZrO<Subscript>2</Subscript> films in gas-phase oxidation of alcohols

We have used the sol-gel template synthesis method to obtain mesoporous zirconium-containing titanium dioxide films and have studied their structural and sorption characteristics, surface acid function, and photocatalytic activity during gas-phase oxidation of aliphatic alcohols. We have shown that the zirconium content changes the acidity and specific surface area of the films, determining the rate at which the studied processes occur and the relative yield of reaction products. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 41, No. 6, pp. 354–359, November–December, 2005.     

Characterization of nanocrystalline anatase TiO<Subscript>2</Subscript> thin films

Nanoporous thin films were deposited onto glass substrates by painting with a solution of nanocrystalline anatase TiO(2) particles (with a size of either 6 nm or 16 nm) suspended in an organic solvent. Upon drying in air for about 1 day, the films were tempered at 450 degrees C in air for 1 h. This procedure results in stoichiometric TiO(2) films with a thickness of several micro m and a milky whitish appearance. Scanning force microscopy of the surface revealed that the nanoparticles of the films agglomerated into structures with lateral dimensions of some 100 nm. Transmission electron microscopy was utilized to investigate the structural arrangement of the crystallites in the films. High-resolution electron diffraction and X-ray diffraction analyses demonstrated, furthermore, that the material consists exclusively of a single TiO(2) phase, namely anatase, and that the films do not exhibit any preferential texture. The elemental stoichiometry and the possible presence of impurities were monitored throughout the films by means of secondary-ion mass spectrometry depth profiling. Electrical measurements have been carried out as a function of both the sample temperature T and the ambient oxygen partial pressure p(O(2)). From these data the electrical conductivity sigma of the porous films was determined in dependence of those parameters.     

Photocatalytic properties of electric-explosion-produced TiO<Subscript>2</Subscript> nanopowder

Structural features and physicochemical and photocatalytic properties of an electric-explosion-produced titanium dioxide powder were studied by means of X-ray phase and X-ray diffraction analyses, transmission electron microscopy, thermal analysis, and optical spectroscopy.     

Dielectric properties and I-V characteristics of (Pb<Subscript>0.4</Subscript>Sr<Subscript>0.6</Subscript>)TiO<Subscript>3</Subscript> thin films improved by TiO<Subscript>2</Subscript> buffer layers

A TiO₂ thin buffer layer was introduced between the (Pb_0.4Sr_0.6)TiO₃ (PST) film and the Pt/Ti/SiO₂/Si substrate in an attempt to improve their electrical properties. Both TiO₂ and PST layers were prepared by a chemical solution deposition method. It was found that the TiO₂ buffer layer increased the (100)/(001) preferred orientation of PST and decreased the surface roughness of the films, leading to an enhancement in electrical properties including an increase in dielectric constant and in its tunability by DC voltage, as well as a decrease in dielectric loss and leakage current density. At an optimized thickness of the TiO₂ buffer layer deposited using 0.02 mol/l TiO₂ sol, the 330-nm-thick PST films had a dielectric constant, loss and tunability of 1126, 0.044 and 60.7% at 10 kHz, respectively, while the leakage current density was 1.95 × 10⁻⁶ A/cm² at 100 kV/cm.     

Photoelectrochemical study of electrodeposited TiO<Subscript>2</Subscript> thin films onto F:SnO<Subscript>2</Subscript> substrates

TiO₂ thin films have been effectively fused onto F:SnO₂ (FTO) substrates via the electrodeposition method. The influence of deposition temperature on the synthesis of F:SnO₂ substrates and relative information of as-deposited and annealed TiO₂ thin films have been studied. Novel TiO₂ microspheres are detected on F:SnO₂ substrates at an optimized electrodeposition potential. Raman bands approve the creation of single-anatase-phase TiO₂. The optimized deposition surroundings show a decrease in the band gap of F:SnO₂ substrates and TiO₂ thin films. The determined photoelectrochemical properties of annealed TiO₂ thin films indicate a fill factor of 51% and power conversion efficiency of 0.15% for application in solar cells.     

Photocatalytic activity of Au/TiO<Subscript>2</Subscript> nanocomposite for azo-dyes degradation

The structural properties of Au/TiO₂ catalyst were studied by X-ray diffraction, UV-visible diffuse reflectance, photoluminescene, scanning transmission and electron microscope, and temperature programmed reduction. The photocatalytic activity of the catalysts was evaluated for the degradation of various azo-dyes such as methylene blue, methyl orange, reactive blue-4, and eosin-B under solar irradiation. It was found that TiO₂ catalyst modified with gold exhibits higher percentage of degradation compared to starting TiO₂. For example, TiO₂ showed 35% of methyl orange degradation whereas gold modified TiO₂ possessed 82%. Effect of different parameters such as pH and dye concentration has been evaluated and the photocatalytic activity was correlated with physico-chemical properties. The dye degradation rate followed first order kinetics.     

Ce(4+) doped TiO<Subscript>2</Subscript> thin films: Characterization and photocatalysis

Undoped and Ce(4+) doped TiO₂ thin films were prepared by sol-gel method. The samples were characterized using scanning electron microscopy, the photocatalytic reactivity was evaluated by degradation of methylene blue in the aqueous solution. 0.5 wt. % Ce(4+) doped TiO₂ thin films calcined at 400°C show the highest photocatalytic activity. The text was submitted by the authors in English.     

Thermal behavior of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> mesoporous gels

Summary Titania-based photocatalytic materials were prepared by sol-gel method using Fe³⁺ and polyethyleneglycol (PEG₆₀₀) as additives. Thermogravimetry (TG), differential thermal analysis (DTA) and evolved gas analysis (EGA) with MS detection were used to elucidate processes that take place during heating of Fe³⁺ containing titania gels. The microstructure development of the Fe₂O₃/TiO₂ gel samples with and without PEG₆₀₀ admixtures was characterized by emanation thermal analysis (ETA) under in situ heating in air. A mathematical model was used for the evaluation of ETA results. Surface area and porosity measurements of the samples dried at 120&deg;C and the samples preheated for 1 h to 300 and 500&deg;C were compared. From the XRD measurements it was confirmed that the crystallization of anatase took place after thermal heating up to 600&deg;C.     

Photocatalytic reduction of CO<Subscript>2</Subscript> over TiO<Subscript>2</Subscript> based catalysts

At present, carbon dioxide is considered the largest contributor among greenhouse gases. This review covers the current state of problem of carbon dioxide emissions from industrial and combustion processes, the principle of photocatalysis, existing literature related to photocatalytic CO₂ reduction over TiO₂ based catalysts and the effects of important parameters on the process performance including light wavelength and intensity, type of reductant, metal-modified surface, temperature and pressure. Presented at the 34th International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 21–25 May 2007.     

Photocatalytic activity of visible light-responsive TiO<Subscript>2</Subscript> thin films deposited on various anodized Ti-metal substrates by a RF magnetron sputtering method

Visible light-responsive TiO₂ (Vis-TiO₂) thin film has been deposited on two different kinds of anodized Ti-metal substrates, i.e., plate-type Titanystar (P-Titanystar) or non-woven fabric Titanystar (N-Titanystar) by a radio-frequency magnetron sputtering (RF-MS) method. These Vis-TiO₂ thin film photocatalysts (Vis-TiO₂/P-Titanystar and Vis-TiO₂/N-Titanystar) showed high activity for the oxidation of 2-propanol in water under UV light irradiation while Vis-TiO₂/N-Titanystar showed higher activity than Vis-TiO₂/P-Titanystar. Furthermore, photocatalytic activity of Vis-TiO₂/N-Titanystar was enhanced by the Pt deposition by an RF-MS deposition method. Pt loaded Vis-TiO₂/N-Titanystar (Pt-Vis-TiO₂/N-Titanystar) acted as an efficient photocatalyst for the oxidation of methanol vapor under UV light irradiation even in a flow system. Moreover, it was found that Pt-Vis-TiO₂/N-Titanystar is an effective photocatalyst for the oxidation of various organic compounds in gas phase or ammonia gas even under visible light irradiation (λ > 420 nm) at 293 K.     

Sol–gel synthesis,characterization and photocatalytic activity of mesoporous TiO<Subscript>2</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3 </Subscript>granules

Mesoporous TiO₂/γ-Al₂O₃ composite granules were prepared by combining sol–gel/oil-drop method, using various titania solution. The product granules can be used as a photocatalyst or adsorbent in moving, fluidized bed reactors. The phase composition and pore structure of the granules can be controlled by calcination temperature and using different titania solution. In the photocatalysis of NH₃ decomposition, TiO₂/γ-Al₂O₃ granules using Degussa P25 powder treated thermally at 450 °C showed the highest catalytic ability. However, TiO₂/γ-Al₂O₃ granules using titania made by hydrothermal method had comparable performance in NH₃ decomposition.     

Effect of heat treatment on electrochromic properties of TiO<Subscript>2</Subscript> thin films

Electrochromic titanium oxide (TiO₂) films were deposited on ITO/glass substrates by chemical solution deposition (CSD). The stock solutions were spin-coated onto substrates and then heated at various temperatures (200–500 °C) in various oxygen concentrations (0–80%) for 10 min. The effects of the processing parameters on the electrochromic properties of TiO₂ films were investigated. X-ray diffraction measurements demonstrated that the amorphous TiO₂ films were crystallized to form anatase films above 400 °C. The electrochromic properties and transmittance of TiO₂ films were measured in 1 M LiClO₄–propylene carbonate (PC) non-aqueous electrolyte. An amorphous 350 nm-thick TiO₂ film that was heated at 300°C in 60% ambient oxygen exhibited the maximum transmittance variation (ΔT%), 14.2%, between the bleached state and the colored state, with a ΔOD of 0.087, Q of 10.9 mC/cm², η of 7.98 cm²/C and x in Li _x ClO₄ of 0.076 at a wavelength (λ) of 550 nm.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Mesoporous TiO<Subscript>2</Subscript> thin films prepared from hydrothermally treated precursor powder sols

Two series of TiO₂ thin films were prepared based on soluble precursor powders: The first run originated directly from an alcohol-based coating solution whereas for the second batch the aqueous precursor powder sol had previously undergone a hydrothermal treatment. The respective microstructures were characterized by electron microscopy, the phase evolution was monitored by X-ray diffraction. Ellipsometric porosimetry (EP) was employed to reveal changes of porosity and pore size induced by thermal treatment of the films.

Open image in new window

Soluble TiO₂ precursor powders were hydrothermally treated to yield coating solutions. Films from these sols were compared with those directly obtained by dissolving the precursor powders. Results indicate that crystallization to anatase is induced under hydrothermal conditions and the resulting films mostly maintain their porosity throughout thermal treatment. In contrast to that coatings processed from as-dissolved precursor powders undergo more extensive densification

     

Preparation and photocatalytic activity of TiO<Subscript>2</Subscript> films with Ni nanoparticles

Titania thin films were synthesized by sol–gel dip-coating method with metallic Ni nanoparticles synthesized separately from an organometallic precursor Ni(COD)₂ (COD = cycloocta-1,5-diene) in presence of 1,3-diaminopropane as a stabilizer. Titania was obtained from a titanium isopropoxide precursor solution in presence of acetic acid. A Ni/TiO₂ sol system was used to coat glass substrate spheres (6, 4 and 3 mm diameter sizes), and further heat treatment at 400 °C was carried out to promote the crystallization of titania. XRD analysis of the TiO₂ films revealed the crystallization of the anatase phase. Transmission Electron Microscopy (TEM) and High Resolution TEM studies of Ni nanoparticles before mixing with the TiO₂ solution revealed the formation of Ni nanostructures with an average size of 5–10 nm. High-angle annular dark-field images of the Ni/TiO₂ system revealed well-dispersed Ni nanoparticles supported on TiO₂ and confirmed by AFM analysis. The photocatalytic activity of the Ni/TiO₂ films was evaluated in hydrogen evolution from the decomposition of ethanol using a mercury lamp for UV light irradiation. Titania films in presence of Ni nanoparticles show higher efficiency in their photocatalytic properties in comparison with TiO₂.     

Photocatalytic activity of a mesoporous TiO<Subscript>2</Subscript>/Ni composite in the generation of hydrogen from aqueous ethanol systems

TiO₂/Ni metal-semiconductor composites were prepared from mesoporous titanium dioxide obtained by sol-gel precipitation in the presence of a structure-forming template. The photocatalytic activity of mesoporous TiO₂/Ni composites in the generation of hydrogen from aqueous ethanol mixtures was discovered and studied in detail.__________Translated from Teoreticheskaya i Éksperimentalnaya Khimiya, Vol. 41, No. 1, pp. 24–29, January–February, 2005.     

Nanosized TiO<Subscript>2</Subscript> particles decorated on SiO<Subscript>2</Subscript> spheres (TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript>): synthesis and photocatalytic activities

Nanosized TiO₂ and nano-anatase TiO₂ decorated on SiO₂ spherical core shells were synthesized by using a sol–gel method. The synthesized pure TiO₂ nano particle and TiO₂ grafted on SiO₂ sphere with various ratios have been characterized for their structure and morphologies by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrophotometry (FTIR) and transmission electron microscopy (TEM). Their surface areas were measured using the BET method. The photocatalytic activity of all nanocomposites was investigated using methylene blue as a model pollutant. The synthesized TiO₂/SiO₂ particles appeared to be more efficient in the degradation of methylene blue pollutant, as compared to pure TiO₂ particles.     

Photocatalytic degradation of dichloroacetyl chloride adsorbed on TiO<Subscript>2</Subscript>

Dichloroacetyl chloride (DCAC) attracted our attention as an intermediate product of the photocatalytic degradation of trichloroethylene (TCE). The adsorption and photocatalytic reaction of DCAC on TiO₂ have been investigated by FTIR spectroscopy. The influence of the surface structure of several TiO₂s on the reaction mechanism was discussed in order to understand the complete degradation mechanism of TCE as well as DCAC. DCAC was transformed into dichloroacetic acid (DCAA) on the relatively hydrophobic TiO₂ surface by the small amount of the water molecules weakly adsorbed on the surface. This DCAA was degraded to phosgene, CO₂, and CO during UV irradiation. For the hydrophilic TiO₂, DCAC was mainly transformed into the dichloroacetate anion. UV irradiation allowed this species to produce chloroform in addition to phosgene, CO₂, and CO. It is suggested that DCAC easily reacts with the Ti–OH group on the hydrophilic TiO₂ and forms the bidentate titanium chelate of dichloroacetate, which efficiently degrades into chloroform.     

Electrochemical impedance spectroscopy of mesoporous Al-stabilized TiO<Subscript>2</Subscript> (anatase) in aprotic medium

High-frequency electrochemical impedance spectroscopy was used to investigate the mesoporous film of Al-stabilized TiO₂ on F-doped SnO₂ support in 1 M Li(CF₃SO₂)₂N in ethylene carbonate/dimethoxyethane (1:1 v/v). Kinetic parameters, viz. charge transfer resistance and chemical diffusion coefficient, were determined. Charge transfer resistance increased with time of contact of electrode in the above aprotic electrolyte solution. The increase followed exponential dependence, whereas the double layer capacitance, simultaneously, decreased exponentially with time. These effects were discussed in terms of the solid–electrolyte interface, which undergoes chemical changes upon contact with the electrolyte solution. Adel Attia is currently on leave from the Department of Physical Chemistry, National Research Center, El-Tahrir St., Dokki 12622, Cairo, Egypt.     

TiO<Subscript>2</Subscript> nanofibers embedding single crystalline TiO<Subscript>2</Subscript> nanowires

Epitaxially grown titanium dioxide (TiO₂) nanofibers embedding single crystalline TiO₂ nanowires (NWs) were successfully fabricated by electropinning poly(vinyl pyrrolidone)/ethanol solutions mixed with hydrothermally synthesized TiO₂ NWs and titanium isopropoxide precursors and subsequently calcinating the electrospun nanofibers. Utilizing scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the morphologies of TiO₂ NWs and nanofibers were investigated. High resolution TEM (HR-TEM) and selected area electron diffraction (SAED) allowed us to indentify the fact that, during the calcination process under the optimized condition, titanium isopropoxide precursors were epitaxially crystallized on the surface of single crystalline TiO₂ NWs. Based on the X-ray diffraction (XRD) experiments, it was also realized that the crystalline structure of hydrothermally synthesized TiO₂ NWs and epitaxially crystallized TiO₂ nanofibers is anatase and that TiO₂ composite nanofibers embedding TiO₂ NWs exhibited a higher crystallinity than the pristine TiO₂ nanofibers. Additionally, ultraviolet visible (UV–Vis) spectra of nanofibers indicated that optical properties of TiO₂ nanofibers can be tuned by introducing the single crystalline TiO₂ NWs.