Radiation Damage of Crystal Polyesters

The change of crystal structures in polyethylene terephthalate (PET) and polyhexa methylene terephthalate (PHT) irradiated by γ-ray were investigated by using the methods of WAXD and SAXS. It was found that irradiation caused the crystal parameters of PET and PHT to lengthen, and the cell to expand; and at the same time, the long period and the thickness of lamellae were unchanged. These results indicate that the radiation damage of crystal polyesters causes the increase of lacunaries within the crystal polyester.     

Photochemical degradation of environmentally persistent perfluorooctanoic acid （PFOA） in the presence of Fe（Ⅲ）

Environmentally persistent and bioaccumulative perfluorooctanic acid （PFOA） was difficult to be decomposed under the irradiation of 254 nm UV light. However, in the presence of 80μmol/L Fe（Ⅲ）, 80% of PFOA with initial concentration of 48μmol/L （20 mg/L） was effectively degraded and 47.8% of fluorine atoms in PFOA molecule were transformed into inorganic fluoride ion after 4 h reaction. Shorter chain perfluorocarboxylic acids bearing C3-C7 and fluoride ion were detected and identified by LC/MS and IC as the degradation products in the aqueous solution. It was proposed that complexes of PFOA with Fe（Ⅲ） initiated degradation of PFOA irradiated with 254 nm UV light.     

STUDIES ON THE ASYMMETRIC DECOMPOSITION OF D,L-LEUCINE INDUCED BY ~(60)Co γ-IRRADIATION

Sublimed D-,L-,and DL-leucine under vacuum were subjected to ~(60)Co γ-irradiation withdifferent doses.The enantiomeric compositions of samples were determined by chirasil-val capillary column gas chromatography,and the relative yields of radiolytic products(H_2,CO_2 and NH_3)were measured by packed column gas chromatography.The obtained datashowed the peak area ratios D/L of DL-leucine after different absorbed doses of irradiationare all the same as that of samples with no irradiation,within the limit of error.So are theratios for the separately irradiated D-and L-leuicne.This suggests that no asymmetric decom-position was found.The relative yields D/L of radiolytic products(H_2,CO_2 and NH_3)arevery close to 1.00,indicating that the D-leucine cleavage rate was the same with that of theL-leucine.From the view of dissipative structure,an explanation for the result was presented.     

A COMPARISON OF DENATURATION AND INACTIVATION RATES OF CREATINE KINASE IN GUANIDINE SOLUTIONS

Both the denaturation, as followed by UV absorbance and fluorescence changes, and inac-tivation of creatine kinase in guanidine solutions have been found to be first order reactions.In 3 M guanidine, at 30℃, the inactivation rate constant was found to be 5.9 sec~(-1) and thedenaturation rate constant 1.9 sec~(-1). At lower guanidine concentrations, the inactivation rateconstants were only little affected whereas the denaturation rate constants decreased markedly,being of the order of 0.04 in 1 M and 0.004 in 0.5 M guanidine. The kinetics of the inactiva-tion reaction in 0.5 M guanidine was found to be in agreement with a combination of two firstorder reactions. The enzyme lost activity first by a fast reaction with a rate constant onlyslightly lower than the rate constant in 3 M guanidine followed by a slower reaction with a rateconstant of 0.003 sec~(-1). In 0.3 M guanidine, very little change in either UV absorbance or influorescence was observed, but, in sharp contrast, the enzyme lost considerable activity by a fastreaction and this was followed by a slower reaction of inactivation. Even after prolongeddenaturation in 0.5 and 0.3 M guanidine, residual activities of 3.4% and 30% remained res-pectively. The above results suggest a very fragile active site although dissociation of thedimer and reversible guanidine inhibition may also contribute to the initial rapid inactiva-tion. It is also to be noted that the multiphasic courses of inactivation at lower guanidineconcentrations seem to suggest the presence of partly active intermediates during denaturation.     

A STUDY ON MECHANICAL PROPERTIES OF γ-RAY IRRADIATED HDPE FILLED WITH SERICITE-TRIDYMITE-CRISTOBALITE*

The effect of γ-ray irradiation on the mechanical properties of high densitypolyethylene(HDPE) filled with sericite-tridymite-cristobalite(STC) was studied. The ex-perimental results show that γ-ray irradiation can improve the affinity between HDPE andSTC, and the dispersion of STC in HDPE matrix. Compared with HDPE/STC (80/20)blend, the yield stress and impact strength of irradiated HDPE (10kGy)/STC (80/20) blendare increased from 22.8 MPa and 70J/m to 28.5 MPa and 144J/m. The yield stress andimpact strength of HDPE/irradiated HDPE/STC (48/32/20) are 27.8MPa and 210J/m,respectively.     

Separation and Determination of Trace Amounts of Thallium by Nano-TiO2 Combined with Microwave Irradiation

Nano-TiO2 was employed for the separation and preconcentration of thallium.It was found that the adsorption ratio of thallium ions was more than 98% at pH 4.5 and the desorption ratio reached 99% under microwave irradiation for 3 min at 350 W.The adsorption equilibrium was well described by the Langmuir isotherm model with a maximum adsorption capacity of 4.09 mg/g[(20±0.1) °C].The nano-TiO2 was successfully applied to the determination of element thallium in the certified reference material polymetallic nodule and water samples.     

PHOTOSENSITIVITY OF Ce (Ⅳ) INITIATED METHYL ACRYLATE POLYMERIZATION

The influences of UV light irradiation (313 nm) and diffused daylight on the polymerization of methyl acrylate initiated by the ceric ammonium nitrate without any reducing agent have been studied both in aqueous nitric acid and in pure water. The rate of polymerization was found to be accelerated and the overall activation energy and the induction time were found to be decreased sharply by the UV light irradiation. Under UV light, the rate of polymerization is 8 times as high as the rate in dark. The rate of polymerization was found to attain a maximum with the increase of nitric acid concentration and the rate of polymerization became less sensitive to UV light in the presence of nitric acid whereas the induction period reduced outstandingly. Based on the experimental results, the mechanism is proposed.     

REINFORCEMENT OF POLYDIMETHYLSILOXANE NETWORKS BY NANOCALCIUM CARBONATE

Although a number of investigations have been devoted to the analysis of silica or carbon black filled elastomer networks, little work has been done on the reinforcement of CaCO3 filled elastomer network. In this work, the reinforcement of polydimethylsiloxane (PDMS) network by using CaCO3 nano-particles was investigated. We have found a simultaneous increase of tensile strength, modulus and elongation with the increase in nano-CaCO3 content, which suggests that nano-CaCO3 particles can indeed be used as a reinforcing agent, just like silica or carbon black. Interestingly, the tensile strength,modulus and elongation were seen to leave off for the first time when the content of nano-CaCO3 particles reaches to 80%.PDMS also showed an enhanced elastic modulus and storage modulus with the increase in nano-CaCO3 content, particularly for samples with high nano-CaCO3 content. SEM was used to investigate the dispersion of the filler in PDMS matrix. A better dispersion was found for samples with high nano-CaCO3 content. A great increase of viscosity was found for samples with higher filler content, which is considered to be the reason for the good dispersion thus the reinforcement, because high viscosity will be helpful for breaking the agglomerates of fillers into small size particles under effect of shear. Our work provides a new way for the reinforcement of elastomer by using an adequate amount of nano-CaCO3 particles instead of as mall quantity of silica, which is not only economically cheap but also very effective.     

The synthesis and photoactivated cytotoxicity of novel 5-phenyl-3- （2,2＇：5＇,2″-terthien-5-yl）-4,5-dihydro-lH-pyrazolines

A series of novel 5-phenyl-3-（2,2＇：5＇,2″-terthien-5-yl）-4,5-dihydro-lH-pyrazolines were synthesized in this report. Their photoactivated cytotoxicities on the 5podoptera litura （SL） cell line were evaluated using the MTT method. It was noticed that the inhibitory activities of all the conjugates was enhanced when irradiated with UV-A light. Compounds 4, 6 and 8 were found to be most effective with inhibition rates of 88.1%, 88.0%, and 90,5%, respectively, For compound B, the inhibition rate value was only slightly enhanced under the irradiation treatment （78.3%） compared to the dark treatment （74.8%）. The relationship analysis between structure and activity showed that the middle thiophene ring played an important role on the inhibitory activities. It was shown that these compounds could be the potential candidates for new photoactivated pesticides.     

具有多个光致变色单元的二芳基乙烯分子光密度的增加

3,4-Diaryl-2,5-dihydropyrrole with multiphotochromophore units la was synthesized and its photochromic properties were investigated. It showed that all photochromophore units underwent reversible ring-opening （1a） and ring-closing （1b） photoisomerization reactions in both solution and polymer film with UV/Vis light irradiation, and photochromic properties of la were similar to those of photochromic diarylethene with monophotochromophore 2a. It was found that the optical density of lb was increased linearly with increase of the photochromophore units by comparison with that of 2b in the same condition. It was also found that no significant changes in absorption band and response time between diarylethenes with multiphotochromophores and monophotochromophore were detected in the same condition.     

Photoinitiated crosslinking of EPDM/inorganic filler blends and characterization of related properties

<正>Photoinitiated crosslinking of ethylene-propylene-diene terpolymer(EPDM) blends filled with calcium carbonate, talc and calcined kaolin(CK) in the presence of benzil dimethyl ketal as photoinitiator and trimethylolpropane triacrylate as crosslinker and their related properties have been studied by different analytical methods.The results from gel content and heat extension determination show that the efficiency of photocrosslinking of EPDM increases with increasing the content of diene and its molecular weight.The EPDM blends with 100 phr different inorganic fillers can be photocrosslinked to gel content of above 60%by 5 s UV-irradiation under optimum conditions.Under the same conditions of irradiation,the orders of photocrosslinking rate and final gel content are EPDM/CaCO_3EPDM/talcEPDM/CK.The data from thermogravimetric analysis,dynamic mechanical thermal analysis,electrical properties,mechanical tests and scanning electron microscopy show that UV irradiation crosslinking apparently enhances the thermal stability,mechanical properties and electrical properties of the photocrosslinked EPDM/inorganic filler samples.Although the attenuated total-reflection FTIR data show that inorganic fillers can promote the surface photo-oxidation of EPDM/inorganic filler samples with increasing the irradiation time,the above related properties of the photocrosslinked EPDM blends irradiated within 5 s are enough to satisfy many applications in the cable industry.     

Mechanism study on the reactions between biphenyl and HNO_2 initiated by 355 nm irradiation in aqueous phase

The reactions taking place in the mixed solution of biphenyl and nitrous acid after it was exposed to UV irradiation were studied in this research work. The transient species were identified with the nanosec- ond transient spectroscopic technique, and the final products were ascertained by GC-MS analysis. It was shown that the OH radical, generated by the direct photolysis of nitrous acid, would attack biphe- nyl molecule to form Bp-OH adduct with a rate constant of 9.5×109 L·mol?1·s?1. The Bp-OH adduct could either react with H or be oxidized by nitrous acid to form nitrosobiphenol. The reactions between biphenyl and nitrous acid under UV irradiation in atmospheric aqueous phase were therefore sug- gested to be one promising source of nitrocompounds in the environment.     

Mechanism study on the reactions between biphenyl and HNO<Subscript>2</Subscript> initiated by 355 nm irradiation in aqueous phase

The reactions taking place in the mixed solution of biphenyl and nitrous acid after it was exposed to UV irradiation were studied in this research work. The transient species were identified with the nanosecond transient spectroscopic technique, and the final products were ascertained by GC-MS analysis. It was shown that the OH radical, generated by the direct photolysis of nitrous acid, would attack biphenyl molecule to form Bp-OH adduct with a rate constant of 9.5×109 L·mol-1·s-1. The Bp-OH adduct could either react with H or be oxidized by nitrous acid to form nitrosobiphenol. The reactions between biphenyl and nitrous acid under UV irradiation in atmospheric aqueous phase were therefore suggested to be one promising source of nitrocompounds in the environment.     

A novel photo-initiated approach for preparing aluminum diethylphosphinate under atmospheric pressure

A novel preparation of aluminum diethylphosphinate（AlPi） was carried out with free-radical addition reaction by means of UV-irradiation under atmospheric pressure.A solution of sodium hypophosphite was treated with ethylene and irradiated with ultraviolet light in the presence of an amount of photoinitiator effective to initiate the free-radical reaction between the hypophosphite anion and the double bond of the ethylene molecule.The ethylene was micro-bubbled into the reaction mixture with the addition of the photoinitiator,and the gas-liquid contact surface and the photoinitiator concentration in the gas-liquid interface were increased largely.The yield of the final product could be improved to about 96%.The contents of P,Al in samples were detected by ICP,and the molecular structure of the samples was confirmed by ³¹P NMR,¹H NMR and FTIR spectroscopic analysis.Thermal stability of the final products was investigated in detail by TG-DTA.     

Analysis of Laser Irradiated Organo-Platinum Films

 A study of the surface electronic configuration and surface morphology of excimer laser irradiated organo-platinum films [cis-dichlorobis(triphenylphosphine)platinum(II)] is presented. The films were deposited by thermal evaporation to a thickness of approximately 1 μm. The organo-platinum films were irradiated in air with 248 nm UV light in order to produce metallic deposits. The irradiation source used was a krypton fluoride excimer laser with a pulse length of approximately 20 ns. After irradiation, the surface morphology of the films was studied by atomic force microscopy, which yielded information concerning the effect of exposure dose on the surface roughness. The composition of the deposits was investigated using X-ray photoelectron and Fourier-transform infrared spectroscopy. The effect of annealing the deposits has also been studied. XPS analysis of the annealed samples has provided evidence for the formation of platinum silicide (PtSi).     

LOW MOLECULAR WEIGHT O-CARBOXYMETHYLATED CHITOSANS DERIVED FROM IRRADIATED CHITOSAN AND THEIR ANTIBACTERIAL ACTIVITY*

 Original chitosan with M_v of 2.7 × 10⁵ was degraded by irradiation with γ-rays and a series of low molecular weight O-carboxymethylated chitosans (O-CMCh) were prepared based on the irradiated chitosan. A kinetic model of the irradiation of chitosan was put forward. Results show that the irradiation degradation of chitosan obeys the rule of random degradation and the degree of deacetylation of irradiated chitosan is slightly raised. The antibacterial activity of O-CMCh is significantly influenced by its MW, and a suppositional antibacterial peak appears when M_v is equal to 2 × 10⁵.     

Fabrication and Visible Light Photocatalytic Activity of Co-doped ZnO Nanorods

Co-doped ZnO nanorods were prepared by electrochemical deposition method in aqueous solution. lb study the as-grown samples, several characterizations were carried out. The scanning electron microscopy（SEM） images show that the samples present a rod-like shape with hexagonal cross sections and roughened surthce. There is a slight shift for （002） diffraction peak of Co-doped ZnO nanorods in XRD because Co2~ ions entered into the ZnO lattice. Energy-dispersive X-ray spectroscopy（EDS） and X-ray photoelectron spectroscopy（XPS） results also show the exist of Co in the sample. Photoluminescence（PL） spectra of the samples were observed at room tempera- ture, the UV emission of Co-doped ZnO shows a slight red shift compared with that of undoped ZnO. Thus, we can reach the conclusion that Zn2＋ ions have been substituted by Co2. ions in the ZnO samples. In addition, photocatalysis property of Co-doped ZnO nanorods was investigated under the irradiation of visible light. It was found that the degradation rate of methyl orange is increased greatly nanorods. by Co-doped ZnO nanorods in comparison to undoped ZnO     

Isomorphous Substitution of Metallic Elements for Zeolite Y in the Aqueous Solution

The substitutions of Ti, Fe and Zr into zeolite Y in the aqueous solutions of (NH4)2TiF6, (NH4)3ZrF7 and (NH4)3FeF6 were systematically Investigated. It was found that Ai atoms in the framework can be replaced by some metallic elements and the extent of substitution depends on the M/A1 ratio of the solution. The maximum allowable M/A1 ratio of the aqueous solution Is related with the radius of the M atom and the stability constant of the MFnm- complex. The substituted zeolite samples with crystallinity greater than 80% were characterized by means of XRD, IR, DTA, TPR and NH3-TPD measurements. The incorporation of Ti, Fe and Zr into the zeolite leads to an increase in the unit cell parameter, a lowering of thermal stability and a red shift of the asymmetric stretching frequency. The extent of these changes is apparently related with the ionic radius of the metallic element and the degree of substitution. The results of various characterization methods show that the het-eroatoms are readily Introduced int     

Radiation grafted poly(vinylidene fluoride)-graft-polystyrene sulfonic acid membranes for fuel cells: Structure-property relationships

<正>Structure-property relationships for poly(vinylidene fluoride)-graft-polystyrene sulfonic acid(PVDF-g-PSSA) fuel cell membranes prepared by a single step method involving radiation-induced grafting of sodium styrene sulfonate(SSS) onto electron beam(EB) irradiated poly(vinylidene fluoride)(PVDF) films were established.The physico-chemical properties of the membranes such as ion exchange capacity,water swelling and proton conductivity were correlated with the degree of grafting(G,%) and the structural changes taking place in the membrane matrix during the preparation procedure. The variation in the crystallinity and the thermal stability of membranes was studied by differential scanning calorimetry (DSC) and thermogravimetric analysis(TGA),respectively.The membranes were found to undergo substantial structural changes in forms of ionic sites increase,hydrophilicity enhancement,hydrophobicity reduction and crystallinity decrease with the variation in G(%) and the preparation method.The structural and thermal properties of the obtained membranes were also compared with their counterparts prepared by a conventional two-steps method i.e.radiation induced grafting of styrene onto EB irradiated PVDF films followed by sulfonation.The PVDF-g-PSSA membranes obtained by a single-step method were found to have superior properties compared to those obtained by the conventional two-steps method.     

Synthesis and Characterization of Phosphated Konjac Glucomannan Hydrogels

Konjac glucomannan （KGM） was crosslinked with sodium tripolyphosphate （STPP） to synthesize hydrogels. The crosslinking reaction was confirmed by FT-IR. The results of degradation test show that the hydrogels retain the enzymatic degradation character of KGM and can be degraded for 74.45% in 5 days by cellulase E0240.