Viscosity and temperature transitions in dimethylacetamide solutions of polyamidobenzimidazole and its blends with polysulfone

The rheological properties of 5% solutions of a fiber-forming polyamidobenzimidazole in DMAA containing LiCl additives and polyamidobenzimidazole-polysulfone blends in the same solvent have been studied. The total concentration of polymer blends with various component ratios is 5 wt %. At temperatures below ∼110°C, the systems under study behave as non-Newtonian fluids and their viscosity decreases with temperature. At T > 110°C, the temperature dependence of viscosity passes through a minimum. The position of the minimum on the temperature scale decreases with the concentration of polyamidobenzimidazole. This character of a change in viscosity is associated with the phase separation of polyamidobenzimidazole solution that leads to its gelation. The temperature corresponding to the minimum viscosity coincides with the onset temperature of a sharp turbidity of solution during heating. It is suggested that solutions containing up to 5% polyamidobenzimidazole possess an LCST. The addition of up to 50% polysulfone has almost no effect on the temperature of transition but brings about a marked decline in the viscosity of the system.     

Helix formation and formaldehyde crosslinking in gelatin solutions

Optical rotation measurements on 5% gelatin solutions containing 0, 2, and 5% formaldehyde (w/w gelatin) are carried out at a series of temperatures between 20°C and 50°C. The solutions without formaldehyde show a diminished growth in rotation with rising temperatures, but even at 50°C there is still a steady rise in rotation with time. The addition of formaldehyde diminishes the optical rotation growth, and at 40°C and above solutions with 5% formaldehyde show no change in rotation at all. The specific rotation and time figures are fitted to a series of third-degree polynomial equations. It is shown that the data do not conform to any pattern of simple reaction kinetics. The mechanism of the formaldehyde–gelatin interaction is discussed.     

Synthesis and properties of nanocrystalline materials based on LaPO<Subscript>4</Subscript>

A study of the processes in which lanthanum orthophosphate nanocrystalline powders with rhabdophane and monazite structure and crystallite size of about 10 nm are formed demonstrated that, at temperatures of up to 500°C, nanocrystalline lanthanum orthophosphate with rhabdophane structure loses crystal hydrate water and is transformed at 520–540°C to a nanocrystalline phase with monazite structure. This transition is not associated with as change in the crystallite size because nanocrystals of the anhydrous lanthanum orthophosphate phase with monazite structure retain a size of about 10 nm both at the instant of the structural transformation and up to temperatures of 600–700°C. The technological modes were determined in which nanocrystalline lanthanum orthophosphate powders with monazite structure can be obtained and the powders are used for sintering of ceramic materials with porosity on the level of 5–7%.     

Ionic liquid crystals derived from the protonation of poly(propylene imine) dendrimers with a cholesterol-based carboxylic acid

The liquid crystalline character of salts resulting from the interaction of poly(propylene imine) dendrimers with 3-cholesteryloxycarbonylpropanoic acid has been studied. The supramolecular structure and consequently the observed liquid crystalline phases are dictated by the degree of protonation of primary amino groups as compared with that of tertiary ones, determined by FTIR spectroscopy in the bulk and by NMR spectroscopy in solution. Glass transition temperatures of the materials are about 38°C. At higher temperatures they are transformed to smectic C* phases while a second-order smectic C phase to smectic A phase transition is observed between 90 and 110°C depending on dendrimer generation. At about 150°C the onset of degradation is observed. The influence of the ionic dendrimeric scaffold on the thermotropic properties is discussed.     

Phases formed during the thermal analysis of pyrite in air

The oxidation of pyrite was studied by thermal analysis and quenching of the phases formed at different stages of the reaction. The phases were characterized by optical microscopy, SEM, EDAX, XRD and microprobe analyses. The phases found were essentially those predicted assuming thermodynamic and pressure equilibria. The predictions were that (1) below 404 °C hematite would form directly on the pyrite surface whereas at higher temperatures magnetite would intervene, (2) pyrrhotite would become a stable phase above 552 °C, (3) ferrous and ferric sulphates would form in the outer layers at temperatures below 583 and 644 °C respectively. The ignition temperature of pyrite was found to correspond with the onset of pyrrhotite formation. An arrest in some of the TG traces was ascribed to the presence of sulphates, the presence or absence of the arrest depending upon the temperature rise sustained by the sample during oxidation.     

Branching by reactive end groups. II. Synthesis,branching, and melt rheology of (meth)acrylate/p‐t‐butylphenol‐coterminated bisphenol a polycarbonates

(Meth)acrylate/p‐t‐butylphenol (PTBP)‐coterminated bisphenol A polycarbonates (PCs) were prepared by interfacial processes and subsequently were reacted at high temperatures (≥200 °C) to form new branched polymers. Two interfacial methods were used to prepare the precursor linear PCs, one with (meth)acryloyl chloride [(M)AC] and the other with (meth)acrylic acid [(M)AA]. Both processes involve phosgenation in the presence of catalytic amounts of triethylamine. The process that used (M)AC formed disproportionately large amounts of bisphenol A di(meth)acrylate, whereas the process using (M)AA required about 50% more phosgene to achieve high (M)AA conversions than typical interfacial PC processes. The branching of the acrylate/PTBP PCs occurred with heating at temperatures greater than or equal to 250 °C. The molecular weight and degree of branching depended on the mole ratio of the thermally reactive and nonreactive coterminators, the total amount of coterminators, and the reaction conditions. The functionality of the branch points formed appeared to be dependent on the acrylate concentration. The branching of the methacrylate/PTBP PCs required the presence of a free‐radical initiator and temperatures up to about 200 °C. The methacrylate end group was less effective than the acrylate on a molar basis in increasing the branched polymer molecular weight and degree of branching. The melt rheology of the branched acrylate/PTBP PCs showed the expected increase in low shear viscosity and shear rate sensitivity with increasing weight‐average molecular weight and acrylate‐end‐group concentration. Small changes in the total terminator concentration and, therefore, the linear precursor polymer molecular weight produced large effects in the low shear rate melt viscosity. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2340–2351, 2000     

Thermal behavior pattern of tributyl phosphate under adiabatic conditions

Violent decomposition of Tributyl Phosphate (TBP), a widely employed extractant in the Plutonium Uranium Extraction process of nuclear fueling reprocessing plants in the presence of Nitric acid at temperatures in excess of 130 °C is a matter of concern in serious accidents including in the Savannah River (USA) and Tomsk (Russia). The thermal behavior of TBP under adiabatic conditions employing the world’s benchmark adiabatic calorimeter, the Accelerating Rate Calorimeter is examined. TBP shows multiple self heating exothermic activities with the onset of primary exotherm at 250 °C. The exothermic activity is accompanied by considerable pressure rise. The thermal decomposition of TBP is found to follow first order Arrhenius kinetic model. TBP loses about 70% of its chemical moieties as volatile matter during the exothermic decomposition. Spectroscopic methods are used to elucidate the degradation pathway.     

Poly(N-isopropylacrylamide). II. Effect of polymer concentration,temperature, and surfactant on the viscosity of aqueous solutions

The effects of polymer concentration, temperature, and surfactant on the rheological properties of poly(N-isopropylacrylamide), poly NIPAM, were studied. Below 28°C the viscosity decreased with increasing temperature according to the Arrhenius expression. However, at 29°C the viscosity increased to a maximum value at 32°C, the lower critical solution temperature (LCST) for aqueous polyNIPAM. Higher temperatures gave a much lower viscosity. This unusual rheological behavior was explained by the phase behavior of the polymer. Sodium dodecyl sulfate (SDS) binding to polyNIPAM increased the cloud point temperature (CPT) and attenuated the unusual rheological behavior of polyNIPAM in water. © 1993 John Wiley & Sons, Inc.     

HPLC of Steroids in Non-aqueous Mobile Phase at Subambient Temperature

Abstract

Increased resolution of steroid mixtures was found in high performance liquid chromatography of steroids at subambient temperatures. With aqueous mobile phase using a reversed phase column it was not possible to decrease temperatures below ?10°C due to increased viscosity. This report describes further increase in resolution at ?50°C using a non-aqueous mobile phase for the separation of steroids. Retention times were shorter several fold while resolution was improved.     

Thermal degradation of copolymers of styrene and acrylonitrile. III. Chain-scission reaction

The chain-scission reaction which occurs in copolymers of styrene and acrylonitrile has been studied at temperatures of 262, 252, and 240°C. Under these conditions volatilization is negligible, and chain scission can be studied in virtual isolation. At 262°C three kinds of chain scission are discernible, namely, at weak links which are associated with styrene units, “normal” scission in styrene segments of the chain and scission associated with the acrylonitrile units. The rate constants for normal scission and scission associated with acrylonitrile units are in the ratio of approximately 1 to 30. The molecular weight of the copolymer has no effect on the rates of scission. At 252°C the same general behavior is observed for the copolymers containing up to 24.9% acrylonitrile. The 33.4% acrylonitrile copolymer is anomalous, however. At 240°C the trends observed at 262°C appear to break down completely although individual experiments are quite reproducible. This behavior at the lower temperatures is believed to be associated with the fact that the melting points of the various copolymers are in this temperature range. Thus the viscosity of the medium, which should be expected to have a strong influence on the chain scission reaction, will be changing rapidly with temperature, copolymer composition, and molecular weight in this temperature range.     

Experimental Study and Numerical Modeling of Rheological and Flow Behavior of Xanthan Gum Solutions Using Artificial Neural Network

This study investigated effect of temperature, concentration, and shear rate on rheological properties of xanthan gum aqueous solutions using a Couette viscometer at temperatures between 25°C and 55°C and concentrations of 0.25 wt% to 1.0 wt%. The Herschel–Bulkley model described very well the non-Newtonian behavior of xanthan gum solutions. Shear rate, temperature, and concentration affected apparent viscosity and an equation was proposed for the temperature and concentration effect valid for each shear rate. This article also presents an artificial neural network (ANN) model to predict apparent viscosity. Based on statistical analysis, the ANN method estimated viscosity with high accuracy and low error.     

Unique rheological behavior of rubber based nanocomposites

Montmorillonite clay (N) based nanocomposites were prepared using three different grades of acrylonitrile butadiene rubber (NBR) (19%, 34%, and 50% acrylonitrile contents), styrene butadiene rubber (SBR), and polybutadiene rubber (BR). Rheological study was carried out on these nanocomposites at three different temperatures (110 °C, 120 °C, and 130 °C) over a range of shear rates for comparison. The results showed that the shear viscosity decreased with increasing shear rate and incorporation of the unmodified (N) and the modified (OC) fillers up to a certain loading, when the results were compared with the gum rubber. This effect became more prominent with increasing polarity of the rubber. The die swell, on the other hand, decreased with loading of N and OC. With increasing filler volume fraction, the die swell further decreased. Decrease of viscosity with concomitant decrease of die swell is unique in such systems. Consecutive runs of the same sample over different shear rates increased the viscosity. The results were explained with the help of X‐Ray Diffraction (XRD) data and Transmission Electron Microscopy (TEM).© 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1854–1864, 2005     

Gas chromatography of manganese(II) and manganese(III) trifluoroacetylacetonates by the ligand vapour technique

The thermal properties and gas Chromatographie behaviour of manganese(II) and manganese(III) trifluoroacetylacetonates (TFA) were investigated by using the ligand vapour technique. The two chelates, Mn(TFA); and Mn(TFA)₃, can be quantitatively eluted on a mixed-liquid phase (1.9% OV-17 ÷ 0.1% PEG-20M) at column temperatures above 210°C and 130–150°C, respectively; Mn(TFA)₃ is completely converted to Mn(TFA)₂ by thermal dissociation at column temperatures above 180°C and completely eluted as Mn(TFA)₂ above 210°C. The chelates can be determined separately within errors of about 1% after a preliminary extraction.     

Time‐Resolved High and Low Temperature Phase Transitions of the Nanocrystalline Cubic Phase in the Y2O3‐ZrO2 and Fe2O3‐ZrO2 System

The nanocrystalline cubic Phase of zirconia was found to be thermally stabilized by the addition of 2.56 to 17.65 mol % Y₂O₃ (5.0 to 30.0 mol % Y, 95.0 to 70.0 mol % Zr cation content). The cubic phase of yttria stabilized zirconia was prepared by thermal decomposition of the hydroxides at 400°C for 1 hr. 2.56 mol % Y₂O₃‐ZrO₂ was stable up to 800°C in an argon atmosphere. The samples with 4.17 to 17.65 mol % Y₂O₃ were stable to 1200°C and higher. All samples at temperatures between 1450°C to 1700°C were cubic except the sample with 2.56 mol % Y₂O₃ which was tetragonal. The crystallite sizes observed for the cubic phase ranged from 50 to 150 Å at temperatures below 900°C and varied from 600 to 800 nm between 1450°C and 1700°C. Control of furnace atmosphere is the main factor for obtaining the cubic phase of Y‐SZ at higher temperature. Nanocrystalline cubic Fe‐SZ (Iron Stabilized Zirconia) with crystallite sizes from 70 to 137 Å was also prepared at 400°C. It transformed isothermally at temperatures above 800°C to the tetragonal Fe‐SZ and ultimately to the monoclinic phase at 900°C. The addition of up to 30 mol % Fe(III) thermally stabilized the cubic phase above 800°C in argon. Higher mol % resulted in a separation of Fe₂O₃. The nanocrystalline cubic Fe‐SZ containing a minimum 20 mol % Fe (III) was found to have the greatest thermal stability. The particle size was a primary factor in determining cubic or tetragonal formation. The oxidation state of Fe in zirconia remained Fe³⁺. Fe‐SZ lattice parameters and rate of particle growth were observed to decrease with higher iron content. The thermal stability of Fe‐SZ is comparable with that of Ca‐SZ, Mg‐SZ and Mn‐SZ prepared by this method.     

Influence of alkali-treatment temperature on the one-dimensional structure of nanosized TiO2

One-dimensional titania nanomaterials were synthesized by soft chemical processes in an alkali medium. The effect of alkali-treatment temperature on the morphology, porosity, and crystalline phase of TiO₂ nanomaterials was investigated. Nanotubes having an opening end were observed when aging the sample at 130 °C, while conducting the process at 180 °C resulted in nanoribbons with a high aspect ratio. Post-treatment at 300 °C led to the partial transformation from tubular structures into nanoparticles or ribbons into nanobelts. While the monoclinic sodium hexatitanate and anatase crystal had a tubular structure, nanoribbons and nanobelt TiO₂ also showed the presence of hydrogen titanate and sodium trititanate. High surface areas were achieved in as-prepared nanotubes and nanoribbons, 456.5 and 72.1 m²/g, respectively, and a drastic reduction was obtained upon post-treatment at 300 °C to 72.1 and 19.2 m²/g, respectively.     

Rheological behavior and prediction for blending conditions of a thermotropic liquid crystalline polyester with nylon

The dynamic rheological behavior of a liquid crystalline polymer (LCP), Vectra™ A, and nylons was investigated. The viscosities of nylon 66 and nylon 6 decrease slowly with an increase in temperature, while the viscosity of Vectra A drops dramatically at 280 °C, but remains slightly changed above 300 °C. At constant frequency and above 300 °C, the mean value of the activation energy of Vectra A is about 87.0 kJ/mole, but jumps to a much higher value of about 407.0 kJ/mole if the melt temperature is below 300 °C. The activation energy of Vectra A above 300 °C is lower than nylon 66, which shows that the viscosity of nylon 66 has a greater temperature dependence than Vectra A. The viscosity ratio of Vectra A to Nylon 66 is less than 1 at temperatures higher than 290 °C, which indicates that Vectra A can form the fibrils in the nylon 66 matrix and reinforce nylon 66 when blending them above this temperature. Experimental data confirm our prediction. Copyright © 2000 John Wiley & Sons, Ltd.     

Acceleration of the cationic polymerization of an epoxy with hexanediol

Thin films of 3,4-epoxycyclohexylmethyl 3',4'-epoxycyclohexane carboxylate were UV irradiated (1.1 J cm^-2) under isothermal conditions ranging from 0 to 50°C. Under these conditions the polymerization advanced quickly but only to a conversion level of less than 10% before the reaction rate slowed by more than an order of magnitude. This drop off in rate was not caused by the glass transition temperature, T _g, reaching or exceeding the reaction temperature, T _rxn, since the epoxide's T _g remained at least 40°C below T _rxn. Raising the sample temperature above 60°C caused a sharp increase in the conversion level. At 100°C conversion exceeds 80% and the ultimate T _g approaches 190°C. The addition of 10 mass% 1,6-hexanediol, HD, to the epoxy caused the conversion at room temperature to quintuple over the level obtained without the alcohol present. The heat liberated from this alcohol epoxy blend during cure on a UV conveyor belt system caused the sample's temperature to increase by about 100°C above ambient whereas the epoxy alone under these conditions only experienced a modest temperature rise of about 26°C. If the amount of HD in the blend is increased above 10% the heat of reaction at 23°C decreases due to HD being trapped in a nonreactive crystalline phase. Boosting reaction temperatures above 50°C melts the HD crystals and yields significantly improved conversion ratios. As the level of alcohol blended with the epoxy is raised its ultimate T _g is lowered and when the concentration of alcohol in the blend nears 30 mass%T _g drops below room temperature. This revised version was published online in July 2006 with corrections to the Cover Date.     

Synthesis and Characterization of Soluble Polyester Based on Calixarene Dicarboxylic Acid with Tertiary Butyl Pendant Groups

A series of new polycalixesters(PCES) were synthesized by polyesterification of calixarene dicarboxylic acid derivatives having tertiary butyl pendant groups at the upper rim using five different diols. All polyesters were readily soluble in polar solvents such as NMP(N-methylpyrrolidone), DMF(dimethylformamide), DMSO(dimethylsulfoxide), pyridine, THF(tetrahydrofurane), HMPA(hexamethylenephosphoramide) and DMAC(dimethylacetamide). The PCES were also partially soluble in TCE(tetrachloroethane) and ethanol and they were unsoluble in aceton. The glass transition temperatures of polyesters were between 80-184 °C, the crystallinity temperatures of polyesters were between 130–212 °C and the melting temperatures of polyesters were between 185–234 °C, as determined by differential scanning calorimeter(DSC). The inherent viscosities of polyesters were obtained from 0.55 dL/mg to 0.61 dL/mg. The temperatures at 10% weight loss of polyesters ranged from 182 °C to 237 °C. The temperatures at 25% weight loss of polyesters ranged from 258 °C to 331 °C. The half weight loss(50%) temperatures of polyesters were among 315 °C to 371 °C and the char yields at 600 °C were determined within 13% to 22.3% in N2 atmosphere, as determined by thermo gravimetric analysis(TGA). The polyester, PES3, has the higher melting point(234 °C) and higher inherent viscosity(molecular weight) than the other polyesters.     

Thermally stimulated depolarization currents of crosslinked polyethylene relaxations in the fusion range of temperatures

With thermally stimulated depolarization currents, we researched the relaxations of crosslinked polyethylene as it is used in medium‐voltage cable insulation. Through conventional polarization two heteropolar peaks stand up in the spectra, at 80 and 105 °C. As the sample is annealed, a homopolar peak is developed at about 99 °C. With window polarization, our results indicated that the 80 °C peak is a structured peak related to polar crosslinking subproducts and impurities. The 105 and 99 °C peaks are fitted to the general kinetic‐order model because the 105 °C peak is related to free‐charge detrapping at the crystalline phase, in the bulk and maybe at the amorphous‐crystal interphases, and the peak that is observed at 99 °C is due to injected charge. Annealing at high temperatures promotes the creation of traps in the material. Charge trapping at T < 70 °C seems to be related to the increased insulator resistivity with annealing time. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1412–1421, 2003     

Accelerating rate calorimeter studies of water-induced thermal hazards of fireworks tip mixture

The objective of this article is to generate thermal decomposition data on fireworks tip mixture, a mixture used to coat the tip of fireworks, for easy ignition. This mixture has reportedly involved in triggering many accidents in fireworks industry. Different quantities of water were added to the mixture and its thermal characteristics were studied. Differential scanning calorimeter was used for screening tests and accelerating rate calorimeter was used for detailed studies in adiabatic and isothermal modes. The self-heat rate data obtained showed onset temperature for different quantity of water, at a range of 80–170 °C. The mixture with 40 % water wt/wt had onset at 80 °C in adiabatic mode. The same mixture on isoaging at 40 °C exhibited exothermic characteristics with a substantial rise in system pressure (57 bar). The heats of exothermic decomposition and Arrhenius kinetics were also computed.