稀土单氧化物发射光谱法的研究I.混合稀土浓集物中钐的双波长测定

报道了空气乙炔火焰中ＳｍＯ蒸气的发射光谱行为，试验了Ｌａ、Ｎｄ、Ｅｕ、Ｙ对ＳｍＯ发射强度增强作用，在大量Ｌａ存在下，ＳｍＯ的发射强度与其浓度成正比关系。用大量Ｌａ作增感剂和干扰抑制剂，借助双波长测定法克服光谱干扰，实现了直接测定高Ｙ混合稀土浓集物中的Ｓｍ，方法准确，快速     

Laser-induced breakdown spectroscopy for simultaneous determination of Sm, Eu and Gd in aqueous solution

This paper reports studies on the determination of trace levels of samarium, europium and gadolinium in aqueous samples by laser-induced breakdown spectroscopy (LIBS). In this work, a membrane-based filter paper was used as a sample support for the liquid samples. The laser-induced plasma was produced in air at atmospheric pressure, using a pulsed Nd:YAG laser. Calibration standards and synthetic mixtures of these lanthanides were prepared using solutions prepared from respective high purity oxides. Linear calibration was obtained for Sm, Eu and Gd by normalizing the intensities of lanthanides emission lines with respective to C(I) 193.029 nm emission line. The concentrations of Sm, Eu and Gd were then determined in a solution containing a mixture of these lanthanides. The concentrations of individual lanthanides were obtained within 5% of the expected values. Limits of detection were found to be 1.3 ppmw (Sm), 1.9 ppmw (Eu) and 2.3 ppmw (Gd).     

萃取色谱分离—原子发射光谱测定氧化钐,氧化铕,氧化钆中14个稀土杂质

用２－乙基己基膦酸单２－乙基己酯萃取色谱分离－原子发射光谱测定超高纯Ｓｍ２Ｏ３、Ｅｕ２Ｏ３、Ｇｄ２Ｏ３中痕量稀土杂质，可用于纯度为９９９９９９％～９９９９９９９％（不含非稀土杂质）Ｓｍ２Ｏ３、Ｅｕ２Ｏ３、Ｇｄ２Ｏ３的纯度分析，１４个稀土杂质的回收率在６７％～１３３％之间，相对标准偏差±６４％～±１８４％，分离周期１０～１４ｈ。     

MPT-AES法同时测定航空润滑油中铁、银和镍

用微波等离子体炬原子发射光谱法(MPT-AES)同时测定未使用过的航空润滑油中铁、银和镍的方法。详细考察了微波功率、载气流量、工作气流量、氧屏蔽气压力等实验参数对铁、银和镍发射强度的影响,并进行了系统优化。测得铁、银和镍的检出限分别为21.94ng/mL0、.36ng/mL9、.82ng/mL,线性范围分别为0.1~100μg/mL、0.001~8μg/mL、0.05~8μg/mL,各元素测定结果的相对标准偏差均小于3.95%,回收率在93.1%~107.4%之间。     

Simultaneous determination of hydride forming (As, Bi, Ge, Sb, Se, Sn) and Hg and non-hydride forming (Ca, Fe, Mg, Mn, Zn) elements in sonicate slurries of analytical samples by microwave induced plasma optical emission spectrometry with dual-mode sample introduction system

A slurry sampling method for the simultaneous determination of hydride forming (As, Bi, Ge, Sb, Se, Sn) and Hg and non-hydride forming (Ca, Fe, Mg, Mn, Zn) elements, without total sample digestion has been developed using the commercial dual-mode sample introduction system (MSIS) coupled with microwave induced plasma optical emission spectrometry (MIP-OES) from biological and environmental reference materials and real samples. The main advantage of this system is its simultaneous determination of elements that form volatile vapor species and elements that do not, without any instrumental changes. Optimization of reaction, nebulization and instrumental conditions was performed to characterize the new system. Slurry concentration up to 4% m/v (particles < 100 μm) prepared in 10% HNO₃ containing 100 μL of decanol, by application of ultrasonic agitation, was used with calibration by the standard addition technique. An ultrasonic probe was used to homogenize the slurry in the quartz cup just before its introduction into the reaction/nebulization system; the multimode sample introduction system (MSIS) combines the benefits of nebulization and vapor generation in a single device. Detection limits (LOD, 3σ_blank, peak area) of 0.07, 0.29, 0.25, 0.10, 0.12, 0.14, 0.11, 0.28, 0.42, 0.02, 0.21 and 0.34 μg g^− 1 were obtained for As, Bi, Ge, Sb, Se, Sn, Hg, Ca, Fe, Mg, Mn and Zn, respectively. The relative standard deviations were ca. 10%, adequate for slurry analysis. To test the accuracy, six certified reference materials were analyzed with the analyte concentrations mostly in the μg g^− 1 level. Measured concentrations are in satisfactory agreement with certified values for the biological reference materials (LUTS-1, DOLT-2) and environmental reference materials (PACS-1, GWB 07302, NIST 2710, NBS 1633b), all adequate for slurry sampling. The method was successfully applied to the determination of the elements in real samples (coal fly ash, lake sediment, sewage). The method requires small amounts of reagents and reduces contamination and losses.     

Simultaneous determination of hydride forming elements (As, Sb, Se, Sn) and Hg in sonicate slurries of biological and environmental reference materials by hydride generation microwave induced plasma optical emission spectrometry (SS-HG-MIP-OES)

A slurry sampling hydride generation (SS-HG) method for the simultaneous determination of hydride forming elements (As, Sb, Se, Sn) and Hg, without total sample digestion, has been developed using batch mode generation system coupled with microwave induced plasma optical emission spectrometry (MIP-OES) from certified biological and environmental reference materials. Slurry concentration up to 3.6% m/v (particles < 80 μm) prepared in 10% HCl containing 100 μl of decanol, by the application of ultrasonic agitation, was used with calibration by the standard addition technique. Harsh conditions were used in the slurry preparation in order to reduce the hydride forming elements to their lower oxidation states, As(III), Sb(III), Se(IV) and Sn(II) and Hg, being reduced to mercury vapor, before reacting with sodium tetrahydroborate. An ultrasonic probe was used to homogenize the slurry in the quartz cup just before its introduction into the reaction vessel. For 10 ml of slurry sample, detection limits (LOD, 3σ_blank, peak area) of 0.06, 0.08, 0.15, 0.12 and 0.10 μg g^− 1 were obtained for As, Sb, Se, Sn and Hg, respectively. The method offers relatively good precision (RSD ranged from 9 to 12%) for slurry analysis. To test the accuracy, three certified reference materials were analyzed with the analyte concentrations mostly in the μg g^− 1 level. Measured concentrations are in satisfactory agreement with certified values for the biological reference materials: NRCC LUTS-1 (lobster hepatopancreas), NRCC DOLT-2 (Dogfish Liver) and environmental reference material: NRCC PACS-1 (Marine Sediment), all adequate for slurry sampling. The method requires small amounts of reagents and reduces contamination and losses.     

Method development for simultaneous multi-element determination of hydride forming elements (As, Bi, Ge, Sb, Se, Sn) and Hg by microwave induced plasma-optical emission spectrometry using integrated continuous-microflow ultrasonic nebulizer-hydride generator sample introduction system

The analytical potential of a coupled continuous-microflow ultrasonic nebulizer dual capillary system (µ-USN/DCS)–Ar/He mixed gas microwave induced plasma-optical emission spectrometry (MIP-OES) has been evaluated for the purpose of determination of hydride forming elements (As, Bi, Ge, Sb, Se, Sn) and a vapor element (Hg). A univariate approach and the simplex optimization procedure were used to achieve optimized conditions and derive analytical figures of merit. Analytical performance of the ultrasonic nebulization system was characterized by determination of the limits of detection (LODs) and precision (RSDs) with the µ-USN/DCS observed at a 15 µL min^{− 1} flow rate. At flows of ≤ 15 µL min^{− 1}, solvent loading in the plasma is sufficiently low to make desolvation unnecessary. The experimental concentration detection limits for simultaneous determination, calculated as the concentration giving a signal equal to three times of the standard deviation of the blank (LOD, 3σ_blank criterion, peak height) were 1.2, 5.4, 6.3, 1.8, 3.3, 2.4 and 3.0 ng mL^{− 1} for As, Bi, Ge, Sb, Se, Sn and Hg, respectively. The method offers relatively good precision (RSD ranged from 8 to 11%) for liquid analysis and microsampling capability. Interference effects by transition metals have been shown to be corrected by the addition of thiourea, as a pre-reducing agent and masking agent. The accuracy of the method was verified using certified reference materials (DOLT-2, GBW 07302, SRM 2710, and SRM 1643e) and by the aqueous standard calibration technique. The measured contents of elements in reference materials were in satisfactory agreement with the certified values.     

Effect of HF addition on the microwave-assisted acid-digestion for the determination of metals in coal by inductively coupled plasma-atomic emission spectrometry

The microwave-assisted acid-digestion for the determination of metals in coal by ICP-AES was investigated, especially focusing on the necessity of adding HF. By testing five certified reference materials, BCR-180, BCR-040, NIST-1632b, NIST-1632c, and SARM-20, it was found that the two-stage digestion without HF (HNO₃ + H₂O₂ was used) was very effective for the pretreatment of ICP-AES measurement. Both major metals (Al, Ca, Fe, and Mg) and minor or trace metals (Co, Cr, Cu, Mn, Ni, Pb, and Zn) in coal gave good recoveries for their certified or reference values. The possibility of ‘HF-memory effect’ was cancelled by the use of a set of vessels which had been never contacted with HF. Twenty-four Japanese standard coals (SS coals) were analyzed by the present method, and the concentrations of major metals measured by the present method provided very high accordance with those from the authentic JIS (Japanese Industrial Standard) method.     

Investigations on the use of pneumatic cross-flow nebulizers with dual solution loading including the correction of matrix effects in elemental determinations by inductively coupled plasma optical emission spectrometry

The use of a so-called trihedral and a T-shaped cross-flow pneumatic nebulizer with dual solution loading for inductively coupled plasma optical emission spectrometry has been studied. By these devices analyte clouds from two solutions can be mixed during the aerosol generation step. For both nebulizers the correction of matrix effects using internal standardization and standard addition calibration in an on-line way was investigated and compared to elemental determinations using a conventional cross-flow nebulizer and calibration with synthetic standard solutions without matrix matching. A significant improvement of accuracy, both for calibration with internal standardization and standard addition, was obtained in the case of four synthetic solutions containing each 40 mmol L^− 1 Na, K, Rb and Ba as matrix elements and 300 μg L^− 1 Cd, Co, Cr, Cu, Fe, Mn, Ni and Pb as analytes. Calibration by standard addition in the case of dual solution loading has been shown to be very useful in the determination of elements at minor and trace levels in steel and alumina reference materials. The results of analysis for minor concentrations of Cr, Cu and Ni in steel as well as for Ca, Fe, Ga, Li, Mg, Mn, Na, Si and Zn in alumina powder certified reference materials subsequent to sample dissolution were found to be in good agreement with the certificates. Limits of detection were found to be only slightly above those for a conventional cross-flow nebulizer and a precision better than 3% was realized with both novel nebulizers.     

Simultaneous determination of bismuth and tellurium in steels by high power nitrogen microwave induced plasma atomic emission spectrometry coupled with the hydride generation technique

An annular-shaped, high power nitrogen microwave induced plasma (N₂-MIP) produced at atmospheric pressure by an Okamoto cavity, as a new excitation source for atomic emission spectrometry (AES), has been used for the simultaneous determination of bismuth and tellurium in steels with the hydride generation method. Under the optimized experimental conditions, the best attainable detection limits at the Bi I 195.389 nm and Te I 200.200 nm lines were 110 and 86 ng/ml for bismuth and tellurium, respectively. The linear dynamic ranges for bismuth and tellurium were 300 to 30,000 ng/ml. The presence of several diverse elements was found to cause a more or less depressing interference with the proposed technique. When bismuth and tellurium in steels were determined, a large amount of Fe(III) in the solution caused a severe depressing interference, while the presence of Fe(II) showed little or no significant interference. Of the several interference-releasing agents examined, l-ascorbic acid was found to be the most preferable to reduce Fe(III) to Fe(II) prior to hydride generation. The concentrations of bismuth and tellurium in steels were determined by the proposed technique. The results obtained by this method were in good agreement with their certified values.     

New methods for the direct determination of dissolved inorganic, organic and total carbon in natural waters by Reagent-Free Ion Chromatography and inductively coupled plasma atomic emission spectrometry

New methods have been developed and applied successfully for the determination of dissolved inorganic, organic and total carbon in water samples. The new methods utilize two instrumental setups, Reagent-Free™ Ion Chromatography (RF™-IC) and inductively coupled plasma atomic emission spectrometry (ICP-AES). Dissolved inorganic carbon (DIC) was measured in untreated samples along with Cl⁻, F⁻ and SO₄²⁻ using RF™-IC and by in-line mixing with 0.1 M HNO₃ to enhance CO₂ removal in the nebulizer, followed by ICP-AES analysis. Total dissolved carbon (TDC) was measured by in-line mixing with 0.1 M NaOH following ICP-AES analysis. Dissolved organic carbon (DOC) was obtained as the difference between DIC and TDC. Only non-volatile organic carbon could be detected by the present method. The workable limits of detection obtained in the present study were 0.5 mM (RF™-IC) and 0.1 mM (ICP-AES) for dissolved inorganic and organic carbon, respectively. The power of the new methods lies in routine analysis of DIC and DOC in samples of natural waters of variable composition and salinity using analytical techniques and facilities available in most laboratories doing water sample analysis. The techniques are sensitive and precise, can be automated using gas-tight sample vials and auto-samplers, and are independent of most elemental interferences with the exception of chloride overload by saline samples when using RF™-IC. The new methods were successfully applied for analysis of DIC and DOC in selected samples of natural and synthetic waters.     

Spectral interferences in the determination of traces of scandium, yttrium and rare earth elements in “pure” rare earth matrices by inductively coupled plasma atomic emission spectrometry. Part IV. Lutetium and yttrium

This article is an electronic publication in Spectrochimica Acta Electronica (SAE), a section of Spectrochimica Acta Part B (SAB). The hardcopy text is accompanied by an electronic archive, stored on the SAE homepage at http://www.elsevier.nl/locate/sabe. The archive contains data files and text files. The present article is the fourth part of a series of papers discussing the spectral interferences of rare earth elements (REEs) in inductively coupled plasma atomic emission spectrometry (ICP-AES). The spectral interferences for 200-pm wide windows centred (±100 pm) around the prominent lines of the analytes, due to matrix lines and oxide radicals (LuO or YO) that emit band spectra depending on the excitation temperature (T_exc.) in ICP were investigated. The main result is that for T_exc.=7200 K, LuO and YO band components can be eliminated so that prominent analysis lines of La, Ce, Pr, Nd, Eu and Sm were observed on a smooth background. T_exc..=7200 K was chosen as the optimal excitation temperature in the determination of traces of REEs in Lu₂O₃ and Y₂O₃, respectively. The quantification of the interferences in terms of Q-value was used in accordance with Boumans and Vrakking [Spectrochimica Acta Part B 42 (1987) 819; 43 (1188) 69]. The “best” analysis lines are free of line interferences and negligibly influenced by wing interferences and Lu₂O₃ and Y₂O₃ as matrices do not raise the real detection limits.     

Simultaneous determination of three alkaloids,four ginsenosides and limonin in the plasma of normal and headache rats after oral administration of Wu‐Zhu‐Yu decoction by a novel ultra fast liquid chromatography‐tandem mass spectrometry method: application to a comparative pharmacokinetics and ethological study

A novel, sensitive and reliable ultra fast liquid chromatography‐tandem mass spectrometry (UFLC‐MS/MS) method has been developed and validated for simultaneous quantitation of eight main active ingredients (evodiamine, rutaecarpine, dehydroevodiamine, limonin, ginsenoside Rb₁, Rd, Re and Rg₁) in rat plasma after oral administration of Wu‐Zhu‐Yu (WZY) decoction, which is a celebrated and widely used Traditional Chinese Medicine formula for the treatment of headache. The analytes and internal standard (IS) were separated on a SHIM‐PACK XR‐ODS II column, and the detection was performed on a UFLC‐MS/MS system with turbo ion spray source. The lower limits of quantification were 1.5, 0.5, 1.0, 2.0, 2.0, 1.0, 0.5 and 0.2 ng ml^?1 for evodiamine, rutaecarpine, dehydroevodiamine, limonin, gensenoside Rb₁, Rd, Re and Rg₁, respectively. Linearity, accuracy, precision and absolute recoveries of the eight analytes were all within satisfaction. The IS‐normalized matrix factor was adopted for assessing the matrix effect and accompanied with a satisfactory result. The validated method has been successfully applied to compare pharmacokinetic profiles of the eight active ingredients in rat plasma between normal and headache rats after administration. Exact pharmaceutical effect of WZY decoction on headache was demonstrated by the ethological response of headache rats induced by nitric oxide donor after administration. The results indicated that the absorption of evodiamine, rutaecarpine, gensenoside Rb₁, Re and Rg₁ in headache group were significantly higher than those in normal group with similar concentration–time curves while no significant differences existed in limonin and ginsenoside Rd between the two groups. Copyright © 2013 John Wiley & Sons, Ltd.