Comparison of the helium/oxygen/acetylene and air/acetylene flames as atom sources for continuum-source atomic fluorescence spectrometry

The helium/oxygen/acetylene flame is compared to the more widely used air/acetylene flame for its utility as an atom cell for atomic fluorescence spectrometry. Nearly identical experimental arrangements were used for both flames in order to make the comparison valid. With a continuum source used for excitation, fluorescence detection limits in the helium/oxygen/acetylene flame were between 13 and 60 times better (lower) than those determined for the same eight elements in the air/acetylene flame. The improved detection limits are attributable mainly to the higher temperature, increased thermal conductivity and lower quenching in the helium flame. Fluorescence background spectra were obtained for both flames over the wavelength range 185–650 nm, and showed the helium flame to have slightly smaller background fluctuations, but a much larger background because of the more favorable fluorescence conditions in the flame.     

The composition and concentration of hydrocarbons in the range of C2 to C18 in downtown Los Angeles,CA

Ambient air samples were collected in the downtown Los Angeles (California) area and analyzed for non-methane hydrocarbons in the range of C2 to C18. Two daily samples were collected, using stainless steel canisters and Tenax-TA solid adsorbent cartridges, over four days in August 1991. The samples were analyzed using high resolution gas chromatographic separation and Fourier transform infrared/mass spectrometric detection (GC/IRD/MSD) or flame ionization detection (FID) of individual hydrocarbons. The comparison of hydrocarbon concentrations found in the Tenax and canister samples and the assessment of the contribution of semivolatile hydrocarbons (C10–C18 range) to the sum of non-methane hydrocarbons (C2–C10 or C2–C12), as measured by the canister method, is presented. This contribution ranges from ~7% to 15% (for C10–C18 range) and ~3% to 8% (for C12–C18 range). The semivolatile hydrocarbons also contribute ~16% to the total ozone forming potential of non-methane hydrocarbons.     

Atomic fluorescence and atomic emission measurements with an image dissector echelle spectrometer

This paper deals with the investigation of an image dissector echelle spectrometer as an analytical instrument for flame atomic fluorescence spectrometry and for flame atomic emission spectroscopy. The fluorescence was induced by high-pressure xenon arc lamps, which emitted continuum spectra and had higher power ratings, i.e. 1.6 and 2.5 kW, than those normally used for the same purpose. The experimental set-up included two different types of premix burners and one type of total consumption burner. A spherical reflector was applied to improve the utilization of the fluorescence radiation. Two different coatings were tested. None gave the expected enhancement.Detection limits and growth curves were measured for 8 different elements (Ca, Co, Cu, Fe, K, Mg, Na and Ni) in a non-separated air/acetylene flame. The attained detection limits were found to be equally good or somewhat better in flame atomic fluorescence excited with continuum sources than previously reported in the literature, i.e. using similar flames. In flame atomic emission spectroscopy better detection limits have been reported before.     

Construction and performance of a time-multiplex multiple-slit flame atomic fluorescence spectrometer for multi-element analysis

The design and performance characteristics of a new multi-element flame atomic fluorescence spectrometer are presented. Radiation from four hollow-cathode tubes is directed onto an unsheathed air—hydrogen flame. The resulting atomic fluorescence is viewed by a special monochromator with a separate exit slit for each element. The light exiting from all slits is directed to a single photomultiplier tube. The fluorescence signals from different elements are distinguished by a time multiplex approach. Single-element detection limits for ten elements and multi-element detection limits for four elements are presented. The degradation of detection limits by flame background emission noise and effect of flame composition on performance are discussed. Better than 1% precision is obtained for moderate analyte concentrations.     

Microdetermination of molybdenum in organometallic compounds by molecular emission and atomic absorption spectrometry

A direct method is described for the determination of molybdenum in mg amounts of organomolybdenum compounds by flame emission or atomic absorption spectrometry. Air/acetylene, air/hydrogen and dinitrogen oxide/acetylene flames were used. The emission of molybdenum oxide is found to be analytically useful in the hydrogen-based flames while the acetylene-based flames are better for atomic absorption. Various organomolybdenum compounds were analysed by both methods as well as by an alternative spectrophotometric method, with satisfactory agreement. The procedure involves simply dissolving the sample in a mixed solvent and aspirating the solution into the flame.     

Solvent extraction—flame spectrometric methods for the determination of indium in aluminium alloys

Atomic absorption and atomic emission methods for determining trace and minor amounts of indium in aluminium alloys are described. They involve the separation of indium from the aluminium matrix by extraction of indium diethyldithiocarbamate from hydrochloric acid at pH 3, and determination by emission at 451.13 nm or absorption at 303.9 nm in the extract; a nitrous oxide—acetylene or air—acetylene flame is used.     

Synthesis,characterization, processability,mechanical properties,flame retardant,and oil resistance of chlorinated acrylonitrile butadiene rubber

Novel chlorinated acrylonitrile butadiene rubber (Cl‐NBR) was prepared from NBR by the alkaline hydrolysis of chloroform by using phase‐transfer catalysis. The formation of Cl‐NBR was monitored by ¹H‐NMR, UV‐Vis, and Fourier transform infrared spectroscopic techniques. The percentage of chlorine attached to the rubber chain was estimated by Volhard method. The effect of polar groups on the structural and thermal properties of Cl‐NBR was analyzed by scanning electron microscopy, X‐ray diffraction analysis, differential scanning calorimetry, and thermogravimetric analysis studies. The flame retardant, oil resistance, cure behavior, and mechanical properties of chlorinated elastomer were also analyzed. The proton NMR revealed the attachment of chlorine in the backbone of NBR with new chemical shift values. The C‐Cl stretching of chlorinated NBR was confirmed from Fourier transform infrared. The UV spectrum also supported the formation of chlorinated unit in the NBR chain through the shifts and broadening of absorption peaks. The X‐ray diffraction analysis pattern indicated a decrease in the amorphous domain of NBR with an increase in the level of chemical modification. The increased glass transition temperature obtained from differential scanning calorimetry confirms the increased molecular rigidity of the chlorinated NBR and thermal transitions increased with increase in the level of chemical modification. The thermal stability of Cl‐NBR decreased with an increase in chlorine content. The flame and oil resistance of Cl‐NBR was greatly higher than pure NBR due to the increased polarity of modified rubber. The superior tensile strength of Cl‐NBR (4 times higher than pure NBR) and higher oil resistance find applications in pump diaphragms, aircraft hoses, oil‐lined tubing, and gaskets materials with the excellent flame resistant property.     

Far-infrared spectroscopy of small polycyclic aromatic hydrocarbons

Both experimental and theoretical spectroscopic studies on small gas phase polycyclic aromatic hydrocarbons in the far-infrared spectral region are reported. The experimental set-up based on thermal emission and Fourier transform far infrared analysis led to the detection of relatively broad vibrational bands, unresolved in rotation, representative of each molecule. Detailed theoretical investigations were performed, including both ab initio calculations and spectral simulations. For the majority of the samples, this study provides the first detection of the vibrational modes associated with the skeleton motions.     

大气气溶胶中多环芳烃的特征光谱检测技术研究

采用紫外-可见分光光度法、傅立叶红外光谱法和恒能量同步荧光分析法进行实验室模拟测试,检测蒽、苯并[a]芘、荧蒽、苯并[k]荧蒽、苯并[ghi]苝5种多环芳烃(PAHs),对比分析了各检测技术的灵敏度、精密度、检出限、线性范围、混合组分图谱分离度等指标。结果表明,恒能量同步荧光法的选择性最好,灵敏度(0.046 0~1.360 5Io.ng-1)和精密度(平均空白的RSD为4.1%)均最高,检出限(0.038~0.427μg.L-1)最低,线性范围较宽(0.126~7 157μg.L-1),是3种光谱分析法中最适合无分离在线检测气溶胶中多组分PAHs的方法。将该方法应用于实际大气环境气溶胶样品中各PAHs成分的定性鉴别和定量检测,5种PAHs均被检出,各物质的特征峰分离效果好,峰形明显,能满足实际测量的分析要求。     

Passive sampling for volatile organic compounds (VOCs) in air at environmentally relevant concentration levels

A sensitive and reliable method is described for the determination of aromatic and chlorinated hydrocarbons (benzene, toluene, o-, m-, p-xylene, trichloromethane, trichloroethane, trichloroethene and tetrachloroethene) in indoor and outdoor air at environmental concentration levels. The procedure can be easily extended to other VOCs. Using passive samplers the VOCs have been adsorbed onto charcoal during a four-week sampling period and subsequently desorbed with carbon disulfide. After injection with a cold split-splitless multi-injector the VOCs have been separated by capillary gas chromatography. Quantification has been achieved using an electron capture detector (ECD) and a flame ionization detector (FID) switched in series. A limit of about 1 g/m³ for aromatic hydrocarbons and of about 0.01 g/m³ for chlorinated hydrocarbons has been obtained. The procedure has been successfully applied in the framework of a field study to measure indoor and outdoor air concentrations in Essen and Borken, two differently polluted areas of Northrhine-Westphalia.     

Atomic spectrometry and flow injection analysis: a synergic combination

The combination of flow-injection techniques with atomic spectrometry (flame atomic absorption and emission spectrometry and inductively-coupled plasma/atomic emission spectrometry) is reviewed, with particular reference to the more recent contributions. The considerable growth in the number of directly couple pre-concentration and matrix isolation is noted, together with the increasing number of reports of indirect methods for metals, inorganic anions and even drug molecules. Many developments are motivated by a desire to increase the performance of the spectrometry over that obtained with conventional methods of sample introduction. Conflicting statements concerning the possible benefits of reduced uptake rate, of air compensation and of peak-area measurement are examined critically. The conflicting requirements of obtaining freedom from stable-compound interferences coupled with god detection limits are discussed, as are means of obtaining the best detection limits. Modifications to nebuliser and spray-chamber design are suggested for maximising peak height (to obtain detection limits) and for working with reduced uptake rates (to reduce stable-compound interferences in flame-based spectrometries). The single well-stirred tank model is used to model nebuliser response and results are presented for the flow-injection behaviour of a Philips Scientific SP9 instrument under conditions of low flow rate which show reasonable agreement with the model. With the instrument, the best detection limits are obtained on the basis of peak-height measurements at the flow rate producing maximum signal-to-noise ratio.     

Development of capillary supercritical fluid chromatography/Fourier transform infrared spectrometry

Summary The feasibility of a new technique, supercritical fluid chromatography/Fourier transform infrared spectrometry (SFC/FTIR), for separation and identification of nonvolatile and labile compounds in complex mixtures is discussed in this report. The design of a high pressure (flow cell) interface is described. The results of a continuing study of possible mobile phases for SFC/FTIR are presented. Finally, SFC/FTIR was applied to a standard test mixture. The current detection limits of one component of the mixture, 2,6-di-t-butylphenol, are presented.     

An evaluation of the spectral noise distribution in analytical flames

The spectral distribution of noises (total, shot and flicker) in a variety of flames has been measured using a computer-controlled spectrometer system. Emission spectra and fluorescence spectra (excited by an Eimac xenon arc lamp) are presented for air/acetylene, nitrous oxide/acetylene, nitrous oxide/propane, air/hydrogen, and an iso-octane liquid fuel flame. Conclusions concerning the predominant type of noise and its cause in each flame are discussed as well as the implications for the analytical flame spectroscopist.     

GC-MS/FID测定环境空气中57种臭氧前体物

建立了GC-MS/FID测定环境空气中57种臭氧前体物的分析方法.优化三级冷阱捕集温度、三级冷阱解析温度、初始柱温、毛细管色谱柱等实验条件.优化条件为:采用硅烷化的苏玛罐采集环境空气,目标组分经三级冷阱在-180℃低温浓缩富集,80℃解析,初始柱温为15℃,结合中心切割技术,将乙烷、乙烯、乙炔、丙烷、丙烯切割至TG-B...     

Determination of chlorinated polycyclic aromatic hydrocarbons in water by solid‐phase extraction coupled with gas chromatography and mass spectrometry

Given the potential risks of chlorinated polycyclic aromatic hydrocarbons, the analysis of their presence in water is very urgent. We have developed a novel procedure for determining chlorinated polycyclic aromatic hydrocarbons in water based on solid‐phase extraction coupled with gas chromatography and mass spectrometry. The extraction parameters of solid‐phase extraction were optimized in detail. Under the optimal conditions, the proposed method showed wide linear ranges (1.0–1000 ng/L) with correlation coefficients ranging from 0.9952 to 0.9998. The limits of detection and the limits of quantification were in the range of 0.015–0.591 and 0.045–1.502 ng/L, respectively. Recoveries ranged from 82.5 to 102.6% with relative standard deviations below 9.2%. The obtained method was applied successfully to the determination of chlorinated polycyclic aromatic hydrocarbons in real water samples. Most of the chlorinated polycyclic aromatic hydrocarbons were detected and 1‐monochloropyrene was predominant in the studied water samples. This is the first report of chlorinated polycyclic aromatic hydrocarbons in water samples in China. The toxic equivalency quotients of chlorinated polycyclic aromatic hydrocarbons in the studied tap water were 9.95 ng the toxic equivalency quotient m^?3. 9,10‐Dichloroanthracene and 1‐monochloropyrene accounted for the majority of the total toxic equivalency quotients of chlorinated polycyclic aromatic hydrocarbons in tap water.     

Determination of volatile chlorinated hydrocarbons in water samples by static headspace gas chromatography with electron capture detection

A simple, efficient, solvent‐free, and commercial readily available approach for determination of five volatile chlorinated hydrocarbons in water samples using the static headspace sampling and gas chromatography with electron capture detection has been described. The proposed static headspace sampling method was initially optimized and the optimum experimental conditions found were 10 mL water sample containing 20% w/v sodium chloride placed in a 20 mL vial and stirred at 50ºC for 20 min. The linearity of the method was in the range of 1.2–240 μg/L for dichloromethane, 0.2–40 μg/L for trichloromethane, 0.005–1 μg/L for perchloromethane, 0.025–5 μg/L for trichloroethylene, and 0.01–2 μg/L for perchloroethylene, with coefficients of determination ranging between 0.9979 and 0.9990. The limits of detection were in the low μg/L level, ranging between 0.001 and 0.3 μg/L. The relative recoveries of spiked five volatile chlorinated hydrocarbons with external calibration method at different concentration levels in pure, tap, sea water of Jiaojiang Estuary, and sea water of waters of Xiaomendao were in the range of 91–116, 96–105, 86–112, and 80–111%, respectively, and with relative standard deviations of 1.9–3.6, 2.3–3.5, 1.5–2.7, and 2.3–3.7% (n = 5), respectively. The performance of the proposed method was compared with traditional liquid–liquid extraction on the real water samples (i.e., pure, tap, and sea water, etc.) and comparable efficiencies were obtained. It is concluded that this method can be successfully applied for the determination of volatile chlorinated hydrocarbons in different water samples.     

The reaction products of the 193 nm photolysis of vinyl bromide and vinyl chloride studied by time-resolved Fourier transform infrared emission spectroscopy

Time-resolved Fourier transform infrared (TRFTIR) emission spectroscopy has been used to study the 193 nm photolysis of vinyl bromide (C(2)H(3)Br) and vinyl chloride (C(2)H(3)Cl). Time-resolved IR emission was analysed to obtain nascent vibrational state populations of two primary photolysis products: HBr (v = 1-7) and HCl (v = 1-6). In both cases the nascent vibrational state populations monotonically decrease with increasing v and are in excellent agreement with previously published data. Time-resolved populations were analysed to yield rate constants for vibrational relaxation of HBr (v = 1-3) and HCl (v = 1-4) by parent vinyl bromide and vinyl chloride, respectively. In both cases the rate constants were found to increase with increasing vibrational quantum number, in agreement with a single quantum de-excitation via vibrational to vibrational energy transfer. Butadiene (C(4)H(6)) was identified as a secondary product of the photolysis of both vinyl halides, and shown to be formed from the reaction of parent vinyl halide with the vinyl radical. The presence of a buffer gas was found to produce a strong emission feature centred at 2,200 cm(-1), the intensity of which was dependent on the pressure of the buffer gas used, and whose kinetics are indicative of a secondary reaction product. We propose that this emission is from the vibrational progression of the electronic transition A(0, v, 1) --> X(0, v, 2) in the secondary reaction product C(2)H, whose formation route is favoured by the presence of buffer gas.     

Polyethylene glycol/graphene oxide coated solid‐phase microextraction fiber for analysis of phenols and phthalate esters coupled with gas chromatography

A new polyethylene glycol/graphene oxide composite material bonded on the surface of a stainless‐steel wire was used for solid‐phase microextraction. The layer‐by‐layer structure increased the adsorption sites of the novel fiber, which could facilitate the extraction of trace compounds. The polyethylene glycol/graphene oxide was characterized by Fourier transform infrared spectroscopy and elemental analysis, which verified that polyethylene glycol was successfully grafted onto the surface of graphene oxide. The performance of the polyethylene glycol/graphene oxide coated fiber was investigated for phenols and phthalate esters coupled with gas chromatography with flame ionization detection under the optimal extraction and desorption conditions, and the proposed method exhibited an excellent extraction capacity and high thermal stability. Wide linear ranges were obtained for the analytes with good correlation coefficients in the range of 0.9966–0.9994, and the detection limits of model compounds ranged from 0.003 to 0.025 μg/L. Furthermore, the as‐prepared fiber was used to determine the model compounds in the water and soil samples and satisfactory results were obtained.     

Fourier transform u.v.-visible molecular luminescence spectrometry: Fluorescence excitation spectra

The analytical utility of Fourier transform spectrometry in the u.v.-vis region was investigated. Molecular fluorescence excitation spectra were acquired for four polycyclic aromatic hydrocarbons frozen in Shpol'skii solvents. Analytical figures of merit were determined for coronene, including a limit of detection of 2 ppb and a precision better than 13% RSD. The major sources of noise in FT/u.v. molecular fluorescence spectrometry are discussed, and results are compared to those reported earlier from wavelength dispersive instruments.     

气相色谱法测定大气中的CO、CO_2以及低级烃类物质

建立了运用气相色谱对大气中一氧化碳、二氧化碳以及3种低级烃类甲烷、乙烯和乙炔进行同时分析的方法。气相色谱分析系统由自动进样器、1个十通阀协同1个六通阀,以及1个十通阀协同1个四通阀组成,可以实现进样、分离和反吹功能。HP-PLOT Q开口毛细管柱用于5种气体的分离,柱后连接热导检测器;分离完成后,一氧化碳和二氧化碳通过甲烷转化炉中的镍催化作用转化为甲烷,用氢火焰离子化检测器进行检测。5种目标分析物在9 min内完全分离。一氧化碳、甲烷、二氧化碳、乙烯以及乙炔的线性范围分别为3.3~4 990.0、3.3~5 010.0、6.6~4 990.0、4.2~5 080.0、3.9~5 030.0μmol/mol,检出限为1.0~2.0μmol/mol,相关系数不低于0.997,相对标准偏差(RSD,n=5)不大于3.5%。该方法简单、准确,可操作性强。