Monitoring of the principal carbonyl compounds involved in malolactic fermentation of wine by solid-phase microextraction and positive ion chemical ionization GC/MS analysis

A new method has been developed to determine acetaldehyde, 2,3-butanedione (diacetyl) and 3-hydroxy-2-butanone (acetoin) in wine by solid-phase microextraction (SPME) and positive ion chemical ionization GC/MS analysis of O-(2,3,4,5,6-pentafluorobenzyl)-hydroxylamine (PFBOA) derivatives. For SPME, a 65-microm PEG/DVB fibre was used; chemical ionization was performed with methane as reagent gas. The best analysis-time/sensitivity compromise was to perform the PFBOA reaction at 50 degrees C for 20 min, followed by 5-min SPME at the same temperature. Quantitative analysis was performed in SCAN mode using o-chlorobenzaldehyde as internal standard (IS), on the signal of the [M + H](+) ion at m/z 240 for acetaldehyde, 266 for acetoin (corresponding to the [M + H - 18](+) ion), 282 for diacetyl (protonated mono-derivatized compound), and 336 for IS. The accuracy and repeatability of the method were suitable for the study aims, and linearity was good in the range of concentration studied, with correlation coefficients of calibration curves 0.997, 0.998 and 0.988 for acetaldehyde, diacetyl and acetoin respectively. Due to the higher polarity of acetoin with respect to other two compounds, lower sensitivity in the detection of this compound was observed. By following the variation of the three carbonyl compounds, malolactic fermentations (MLF) were monitored in Merlot wines and this was carried out in the laboratory by two different bacteria strains.     

Analysis of the degradation products of diproteverine by moving belt LC/MS

Moving belt LC/MS has been used to identify the degradation products of the slow calcium membrane channel inhibitor, Diproteverine, after storage at elevated temperature and humidity. The major products observed result from oxidation. Two of these products, both ketones, yield [M ? 14 + H]⁺ ions by chemical ionization. These unusual ions also occur for some simple aromatic ketones used as model compounds and are shown to arise by reduction of the carbonyl group to a methylene by the reagent gas.     

Development of a headspace GC/MS analysis for carbonyl compounds (aldehydes and ketones) in household products after derivatization with o-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine.

Carbonyl compounds (aldehydes and ketones) are suspected to be among the chemical compounds responsible for Sick Building Syndrome and Multiple Chemical Sensitivities. A headspace gas chromatography/mass spectrometry (GC/MS) analysis for these compounds was developed using derivatization of the compounds into volatile derivatives with o-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine (PFBOA). For GC/MS detection, two ionization modes including electron impact ionization (EI) and negative chemical ionization (NCI) were compared. The NCI mode seemed to be better because of its higher selectivity and sensitivity. This headspace GC/MS (NCI mode) was employed as analysis for aldehydes and ketones in materials (fiber products, adhesives, and printed materials). Formaldehyde was detected in the range of N.D. (not detected) to 39 microg/g; acetaldehyde, N.D. to 4.1 microg/g; propionaldehyde, N.D. to 1.0 microg/g; n-butyraldehyde, N.D. to 0.10 microg/g; and acetone, N.D. to 3.1 microg/g in the samples analyzed.     

Negative chemical ionization in quadrupole ion trap mass spectrometry: Effects of applied voltages and reaction times

The effects of applied voltages and reaction times on negative ion chemical ionization in the quadrupole ion trap are investigated. Mass-selected ejection of undesired reagent ions and selective mass storage of only negative ions are required for practical negative ion chemical ionization. This is achieved by application of rf and dc voltages to the ring electrode to control the mass-to-charge ratios one polarity) of ions stored, as well as by application of a supplemental rf voltage applied across the endcap electrodes to selectively eject ions of a particular mass-to-charge ratio. Even with careful control of these parameters, negative chemical ionization is not as sensitive as electron ionization and positive chemical ionization because of the lack of thermal electrons in the ion trap. Mass selection of the hydroxide anion as a reagent ion and exclusion of all positive ions provide [M ? H]^? ions with little or no fragmentation for a wide variety of compounds.     

Quantitative analysis of fluorimated ethylchloroformate derivatives of non-protein amino acids using positive and negative chemical ionization gas chromatography-mass spectometry

The GC-MS characterization of the ethylchloroformate derivatives of amino acids in an aqueous medium has been applied to non-protein amino acids. Derivatization of non-protein amino acids using ethylchloroformate, trifluoroethanol, and pyridine produced strong [M + 1]⁺ and [M - 1]⁻ ions in positive and negative chemical ionization (CI) modes, respectively. Twenty-one out of the twenty-three non-protein amino acids studied produced detectable ion chromatograms in both ionization modes when methane was used as the CI reagent gas. Mass spectra of these non-protein amino acid derivatives showed characteristic [M - 19]⁺, [M + 1]⁺, [M + 29]⁺, and [M + 41]⁺ peaks in the positive chemical ionization mode, and [M - 1]⁻, and [M + 35]⁻ peaks in the negative chemical ionization mode. The detection limits and the linear dynamic range of trifluorethanol ethylchloroformate derivatives of non-protein amino acids were studied using positive chemical ionization. The detection limits are mostly in the femtomole range.     

Sites of protonation in phenothiazines: Methane and ammonia chemical ionization mass spectra

Positive ion methane and ammonia chemical ionization mass spectra for ten phenothiazine derivatives are reported. The fragmentations observed in the chemical ionization mass spectra are rationalized in terms of the location of the added proton. High-resolution measurements are used to confirm empirical formulae of the ions in the mass spectra. Changes in the mass spectra with a change in the chemical ionization reagent gas from methane to ammonia are described. A comparison with positive ion secondary ion mass spectra of the same compounds show that the amount of fragmentation is higher in the secondary ion mass spectra, but the same types of ions are observed in spectra produced by both ionization methods.     

Electrospray ionization mass spectrometry fingerprinting of beer

After just simple degassing, dilution, pH adjustment and direct flow injection, characteristic fingerprint spectra of beer samples have been obtained by fast (few seconds) electrospray ionization mass spectrometry (ESI-MS) analysis in both the negative and positive ion modes. A total of 29 samples belonging to the two main beer types (lagers and ales) and several beer subtypes from USA, Europe and Brazil could be clearly divided into three groups both by simple visual inspection of their ESI(+)-MS and ESI(-)-MS fingerprints as well as by chemometric treatment of the MS data. Diagnostic ions with contrasting relative abundances in both the positive and negative ion modes allow classification of beers into three major types: P = pale (light) colored (pilsener, pale ale), D = dark colored (bock, stout, porter, mild ale) and M = malt beer. For M beers, samples of a dark and artificially sweetened caramel beer produced in Brazil and known as Malzbiers were used. ESI-MS/MS on these diagnostic beer cations and anions, most of which are characterized as arising from ionization of simple sugars, oligosaccharides, and iso-alpha-acids, yield characteristic tandem mass spectra adding a second and optional MS dimension for improved selectivity for beer characterization by fingerprinting. Direct ESI-MS or ESI-MS/MS analysis can therefore provide fast and reliable fingerprinting characterization of beers, distinguishing between types with different chemical compositions. Other unusual polar components, impurities or additives, as well as fermentation defects or degradation products, could eventually be detected, making the technique promising for beer quality control.     

环丙烷衍生物在D2O离子体系中的H/D交换反应

在D2O化学反应气条件下研究了环丙烷衍生物的H/D交换反应特性.发现了三种新的产物离子[M+1]+、[M+2]+和[M+3]+.应用碰撞诱导碎裂(CID)技术研究了这些离子的碎裂反应特性.实验结果表明三种新的产物离子是由反应物与试剂离子之间发生H/D交换反应生成的.并获得了环丙烷衍生物结构中活泼氢位置及其数量的信息.     

Detection of low molecular weight aldehydes in aqueous solution by membrane introduction mass spectrometry

Membrane introduction mass spectrometry (MIMS) is used to detect low molecular weight aldehydes in aqueous solutions. The best sensitivity was obtained by aqueous phase derivatization of aldehydes with O-(2,3,4,5,6-pentafluorobenzyl)-hydroxylamine (PFBOA) and electron capture detection. This negative chemical ionization mass spectrometry procedure allowed the measurement of C(1)C(6) aldehydes at low concentrations in mixtures. The characteristic ion signals in the mass spectrum of the mixture were verified by examining the full mass spectra and product ion MS/MS spectra of the derivatives of individual aldehydes. A reaction scheme is proposed to explain the fragmentation pattern of the molecular anions (M(-.)) of the derivatives. The processes observed include loss of HF to form (MHF)(-.) ions which then competitively fragment by elimination of H(R)CN and NO(.) to produce ions of m/z 178 and (M-50)(-.), respectively. Multiple reaction monitoring was applied to establish the lower limits of detection. Formaldehyde could be detected without preconcentration at 1 ppb with S/N = 3/1. The detection limits of acetaldehyde, propanal and butanal were found to be 10 ppb and that of pentanal and hexanal were found to be 20 ppb. Response curves vs. concentration are linear in the ppb range. This method is not as readily applicable to the corresponding ketones.     

Internal energy deposition in chemical ionization/tandem mass spectrometry

The efficiency of the collision-induced dissociation (CID) process as a function of the internal energy deposited into the ion during the ionization event was evaluated. (M + H)+ ions of pyrrole, pyrrolidine, pyridine and piperidine (five and six-membered ring heterocyclics) were generated by chemical ionization (CI). The internal energy of the ions was varied by using different reagent gases. Both high-energy (keV) and low-energy (eV) CID were performed on these ions. The experiments showed that the (M + H)+ ions of the five-membered ring compounds, pyrrole and pyrrolidine, have higher fragmentation efficiencies than the six-membered ring compounds, pyridine and piperidine. Fragmentation efficiencies in high-energy CID clearly correlate with the internal energy deposited by the ionization technique. Experiments showed that the low-energy CID process is more sensitive than high-energy CID to changes in internal energy.     

Analysis of aliphatic and aromatic carbonyl compounds in ambient air by LC/MS/MS.

A sensitive liquid chromatograph/tandem mass spectrometric technique (LC/MS/MS) was applied to determine aliphatic and aromatic carbonyl compounds in ambient air. Traces of the carbonyl compounds were sampled by passing through a Sep-Pak DNPH-silica cartridge. Their derivatives were thus eluted with acetonitrile, separated by reversed-phase liquid chromatography and determined by quadrupole tandem mass spectrometry in an atmospheric pressure chemical ionization (APCI) mode with multiple reaction monitoring (MRM). The detection limits (DL) of the carbonyl compounds were 0.8 - 15 ng/m3. A number of the carbonyl compounds were detected at n.d.- 14 microg/m3 levels. The precursor ion scanning analysis was applied to identify the unknown compounds.     

Laser-Induced Acoustic Desorption/Atmospheric Pressure Chemical Ionization Mass Spectrometry

Laser-induced acoustic desorption (LIAD) was successfully coupled to a conventional atmospheric pressure chemical ionization (APCI) source in a commercial linear quadrupole ion trap mass spectrometer (LQIT). Model compounds representing a wide variety of different types, including basic nitrogen and oxygen compounds, aromatic and aliphatic compounds, as well as unsaturated and saturated hydrocarbons, were tested separately and as a mixture. These model compounds were successfully evaporated into the gas phase by using LIAD and then ionized by using APCI with different reagents. From the four APCI reagent systems tested, neat carbon disulfide provided the best results. The mixture of methanol and water produced primarily protonated molecules, as expected. However, only the most basic compounds yielded ions under these conditions. In sharp contrast, using APCI with either neat benzene or neat carbon disulfide as the reagent resulted in the ionization of all the analytes studied to predominantly yield stable molecular ions. Benzene yielded a larger fraction of protonated molecules than carbon disulfide, which is a disadvantage. A similar but minor amount of fragmentation was observed for these two reagents. When the experiment was performed without a liquid reagent (nitrogen gas was the reagent), more fragmentation was observed. Analysis of a known mixture as well as a petroleum cut was also carried out. In summary, the new experiment presented here allows the evaporation of thermally labile compounds, both polar and nonpolar, without dissociation or aggregation, and their ionization to predominantly form stable molecular ions.     

GC/MS-positive ion chemical ionization and MS/MS study of volatile benzene compounds in five different woods used in barrel making

Extracts from acacia, chestnut, cherry, mulberry, and oak wood, used in making barrels for aging wine and spirits were studied by GC/MS positive ion chemical ionization (PICI). Wood chips were extracted by a 50% water/ethanol solution and a tartrate buffer pH 3.2-12% ethanol (model wine) solution. The principal compounds identified in extracts were guaiacol-containing aldehydes and alcohols, such as benzaldehyde and derivatives, vanillin and syringaldehyde, cinnamaldehyde and coniferaldehyde, eugenol and methoxyeugenol, guaiacol and methoxyguaiacol derivatives. PICI using methane as reagent gas produced a high yield of the protonated molecular ion of volatile phenols, compound identification was confirmed by collision-induced-dissociation (CID) experiments on [M + H](+) species. MS/MS fragmentation patterns were studied with standard compounds: guaiacol-containing molecules were characterized by neutral methyl and methanol losses, benzaldehyde derivatives by CO loss. Acacia wood extracts contained significant syringaldehyde and anisaldehyde, but no eugenol and methoxyeugenol. Significant syringaldehyde, eugenol and methoxyeugenol, and high vanillin were found in chestnut and oak wood extracts; low presence of volatile benzene compounds was found in mulberry wood extracts. Cherry wood extracts were characterized by the presence of several benzaldehyde derivatives and high trimethoxyphenol.     

Anomalous ions in the chemical ionization mass spectra of aromatic nitro and nitroso compounds

The appearance of [MH-30]⁺ ions in the chemical ionization mass spectra of aromatic nitro compounds may be due to their initial reduction to the corresponding amines within the ion source. Aromatic nitroso compounds may be similarly reduced to yield [MH-14]⁺ ions. The hydroxy derivatives of the nitroso compounds yield further anomalous ions at [MH-16]⁺ probably due to the reduction of the hydroxy groups.     

Analysis of acrolein and acrylonitrile in aqueous solution by membrane introduction mass spectrometry

Acrolein and acrylonitrile can be quantified directly at low levels in aqueous solution using membrane introduction mass spectrometry. Electron impact was used to generate positively charged ions and electron capture of the O-(2,3,4,5,6-pentafluorobenzyl)hydroxyl amine (PFBOA) derivative was used to generate negatively charged ions of acrolein in aqueous solutions. The origins of all ions in the mass spectra and product MS/MS spectra recorded using both ionization methods were assigned and a reaction scheme is given which accounts for the fragmentation of the PFBOA derivative. Detection limits were measured using multiple reaction monitoring in both the methods. With electron capture detection, acrolein could be detected without preconcentration at 10 ppb levels. Electron impact ionization and multiple reaction monitoring both allowed the measurement of acrylonitrile at levels as low as 10 ppb.     

Electron capture negative ion and positive ion chemical ionization mass spectrometry of polychlorinated phenoxyanisoles

Several polychlorinated phenoxyphenols with three to nine chlorine atoms were examined as their methyl ethers by electron capture negative ion and positive ion chemical ionization and electron impact mass spectrometry. In chemical ionization studies methane, hydrogen, nitrogen, helium and argon were used as reagent gases. Selected compounds were also examined with deuteriomethane, ammonia and deuterioammonia as reagent gases. Utilization of chemical ionization spectra in conjuction with electron impact spectra provides substantial structural information about these compounds. Chemical ionization spectra provide information about chlorine atom substitution. The position of phenoxy substitution can be established from electron capture negative ion and positive ion spectra.     

Chemical ionization of aliphatic nitro compounds

The chemical ionization mass spectra of various aliphatic nitro compounds have been studied. Almost all the nitro compounds form stable [M+H]⁺ ions in sharp contrast to the instability of their ions produced by other ionization techniques. The fragmentations of the [M+H]⁺ ions are discussed, the mechanisms and structures of fragment ions proposed being supported by quantum mechanical calculations. Correlations between chemical ionization mass spectra and structures of compounds studied are outlined. Reliable identification of mono- and polynitroalkanes and some related derivatives may be made by analysis of their chemical ionization mass spectra.     

A Chemical Ionization Mass Spectrometric Study of Fluorescamine and Fluorescamine - Amino Acid Derivatives

Abstract

The chemical ionization mass spectra of fluorescamine and fluorescamine - amino acid derivatives have been studied using methane and ammonia as reagent gases. Major ions in the spectra are protonated molecular ions, adduct ions and ions formed by loss of an oxygen atom.

Fluorescamine, 4-phenyl-spiro[furan-2(3H),1′-phthalan]3,3′-dione, is a powerful new fluorogenic reagent for assaying primary amines.¹ and EI² and EI³ mass spectrometric investigations of fluorescamine and its derivatives were carried out. Our present study reports the CI mass spectral analysis of fluorescamine and some of its amino acid derivatives.     

Chemical ionization mass spectra of simple 1,3-dioxolanes and their sulphur analogues recorded with methane,isobutane, ammonia and acetone as reagent gas

The mass spectral behaviour of nine 1,3-dioxolanes, seven 1,3-dithiolanes and seven 1,3-oxathiolanes was studied under chemical ionization conditions with ammonia, isobutane, methane, acetone, acetone-d₆ or pentan-3-one as reagent gas. The proton affinity of the first members in each series was not large enough for ammonia to protonate them; instead, the ionization took place through unstable [M + NH₄]⁺ ions. Isobutane, which gave rise to abundant [M + H]⁺ ions in all cases, was the best reagent gas for the determination of the molecular mass. Methane chemical ionization caused extensive fragmentations either through ring cleavage or through the elimination of the largest substituent from ring positions 2 as a neutral hydrocarbon. The ketones used as reagent gas reacted to form adduct ions. In the case of dioxolanes and oxathiolanes, the [M + RCO]⁺ adduct ion decomposed through ring opening and then, as a consequence of intramolecular nucleophilic substitution, through the elimination of a neutral carbonyl compound. Resonance-stabilized dioxolanylium and oxathiolanylium ions were obtained for dioxolanes and oxathiolanes, respectively. This reaction was almost non-existent for the dithiolanes.     

Negative ion chemical ionization mass spectrometric studies of tetradentate schiff base coordination compounds. Fluorinecontaining reagent gases

Negative ion mass spectra using chemical ionization conditions have been measured for a series of tetradentate Schiff base corrdination compounds of Co(II), Ni(II) and Cu(II). Fluorine-containing reagent gases CF₄, SO₂F₂ and SF₆ have been used. The formation of molecular negative ions for the complexes is dependent on the reagent gas used. The secondary ions detected are produced by incorporation of CF₃, F and F₂ species into the coordination compounds.