铝-二甲酚橙-吐温20三元体系光度法测定铝

研究了吐温20(Tween20)存在下,铝与二甲酚橙(XO)的显色反应,建立了分光光度法测定微量铝的新方法.结果表明,在pH=3.13的乙酸-乙酸钠缓冲介质中,铝与XO及吐温20反应生成有色络合物,络合物的最大吸收波长位于511 nm处, 表观摩尔吸光系数ε为1.99×10~4 L·moL~(-1)·cm~(-1),在10 mL溶液中,铝量在2.2～15.1 μg范围内符合比耳定律,检出限为0.0018 μg/mL.方法应用于茶叶、沙棘叶中铝的测定,样品加标回收率为96%～102.6%.     

Simultaneous determination of aluminium and beryllium by first-derivative synchronous solid-phase spectrofluorimetry

A method for the simultaneous determination of aluminium and beryllium in mixtures by first-deravative synchronous solid-phase spectrofluorimetry has been developed. Aluminium and beryllium reacted with morin to give fluorescent complexes, which were fixed on a dextran-type resin. The fluoresnce of the resin, packed in a 1-mm silica cell, was measured directly with a solid-surface attachment. The constant wavelength difference chosen to optimize the determination was Deltalambda = lambda(em) = 75 nm. Aluminium was measured at lambda(em)lambda = 445/520 nm and beryllium at lambda(em)lambda(em) = 430/505 nm. The range of application is between 0.5 and 5.0 ng/ml for both aluminium and beryllium. The accuracy and precision of the method are reported. The method has been successfully applied to the determination of aluminium and beryllium in synthetic mixtures and natural waters.     

2,6-Bis[(o-hydroxy)phenyliminomethyl]-1-hydroxybenzene as a reagent for the selective spectrofluorimetric determination of aluminium

A spectrofluorimetric method for the determination of aluminium at ng/ml level has been developed. The method is based on the formation of a fluorescent 11 complex between Al(III) and 2,6-bis[(o-hydroxy)phenyliminomethyl]-1-hydroxybenzene at an apparent pH of 5.0 in an aqueous-ethanol medium (70% v/v ethanol). The influence of reaction variables is discussed. The range of concentration of the method is 1.0–10.0 ng/ml aluminium, the relative standard deviation 1.5% and the limit of detection 0.1 ng/ml. The advantages of the proposed method include high sensitivity and selectivity. The method has been applied to the determination of aluminium in natural waters.     

Spectrofluorimetric determination of trace amounts of aluminium with 5-bromo-salicylaldehyde salicyloylhydrazone

The fluorescent reagent 5-bromo-salicylaldehyde salicyloylhydrazone (5-Br-SASH) was synthesized and its ionization constants were established spectrophotometrically. The fluorescent reaction of this reagent with aluminium was studied. Based on this chelation reaction, a spectrofluorimetric method was developed for the determination of aluminium in acetic acid-ammonium acetate buffer solution of pH 5.4. Under these conditions, the A1-5-Br-SASH complex has excitation and emission maxima at 370 and 460 nm, respectively. The linear range of the method is from 0 to 120 ppb and the detection limit is 1.1 ppb of aluminium. The molar ratio of aluminium to the reagent is 1:3. Interferences of other ions were studied. The method was successfully applied to the determination of aluminium in glucose injection and common beverages.     

On-line aluminium preconcentration on chelating resin and its FIA-spectrofluorimetric determination in foods and dialysis concentrates

A new, sensitive and rapid spectrofluorimetric flow-injection method, is presented for the determination of trace levels of aluminium based on the formation of a fluorescent complex between aluminium and 5,7-dibromo-8-quinolinol (DBQ) and its extraction into diethylether (λ_exc = 400 nm, λ_em = 525 nm). Experimental conditions such as pH, reagent concentration, flow-rates, sample volume, extraction coil length, etc., have been optimized for on-line and batch procedures. The detection limits are 1 ppb and 0.3 ppb for batch and on-line systems respectively. The coeflicient of variation is 3.0% at the 4 ppb level for the FIA system. To remove interferences and to preconcentrate aluminium, a chelating resin microcolumn which was able to selectively complex A1(III) and was obtained by immobilizing Chromotrope 2B on AG1-X8 ion-exchange resin, was incorporated into the FIA system. The proposed method was successfully applied to determine aluminium in tap water, food samples and dialysis solutions.     

Fluorimetric determination of aluminium in serum

A convenient fluorimetric method for the routine determination of aluminium in serum has been developed using lumogallion [4-chloro-3-(2,4-dihydroxyphenylazo)-2-hydroxybenzene-1-sulphonic acid]. Losses of aluminium during deproteinisation of the serum were prevented by treatment with a combination of 20 or 30% m/V trichloroacetic acid (TCA) and 5% m/VTCA. Iron(III) was removed by extraction into chloroform with capriquat (methyltrioctylammonium chloride) as an Fe3+-lumogallion-capriquat ternary complex. The interference from Cu2+ was eliminated by using thiosulphate as a masking agent. The detection limit was 3.6 ng ml-1 and the calibration graph was linear up to 1.4 micrograms ml-1 of aluminium. Using the proposed method, the average concentration of aluminium in the serum of healthy subjects was found to be 6.8 ng ml-1, in agreement with values reported in the literature.     

Determination of fluoride in natural waters by ion-selective electrode potentiometry after co-precipitation with aluminium phosphate

The most effective conditions for masking aluminium in the determination of mug/1. levels of fluoride in water by ion-selective electrode potentiometry after co-precipitation with aluminium phosphate have been re-examined. The effectiveness of citrate for masking aluminium increases with pH, and up to 1.5 x 10(-2)M aluminium can be masked quantitatively at pH 8.5. Fluoride (5-100 mug in 500 ml of sample solution) is quantitatively co-precipitated at pH 4.7 with approximately 90 mg of aluminium phosphate. After dissolution of the precipitate and adjustment of the solution to pH 8.5 with TISAB, the fluoride content can be measured with a fluoride ISE. The method is simple and rapid, and is suitable for the determination of trace amounts of fluoride in various water samples.     

4-(H酸偶氮)-1-苯基-3-甲基吡唑酮光度法测定铝

研究了新试剂４－（Ｈ酸偶氮）－１－苯基－３－甲基吡唑酮（ＨＡＰＭＰ）与铝的显色反应,在ｐＨ４．６的ＨＡｃ－ＮａＡｃ缓冲介质中,ＣＴＭＡＢ存在下,ＨＡＰＭＰ和Ａｌ（Ⅲ）反应生成２∶１红色络合物,λｍａｘ＝５５５ｎｍ,ε＝１．３４×１０５Ｌ·ｍｏｌ－１·ｃｍ－１,铝的含量在０～３．５μｇ／２５ｍＬ内符合比尔定律,方法已用于天然水样中铝的测定。     

Nonextractive spectrofluorimetric determination of aluminium in real, environmental and biological samples using chromotropic acid

An ultra-sensitive and highly selective nonextractive fluorimetric method is presented for the rapid determination of aluminium at nano-trace levels using chromotropic acid as a fluorimetric reagent [lambda(ex) = 360 nm and lambda(em) = 390 nm] in the pH range of 4.1-4.7. The fluorescence intensity of the metal chelate (2:3 complex) reaches a constant value within 1/2 hr and remains unchanged for over 48 hr. The fluorescence intensity aluminium concentration calibration curve is collinear between 1 and 300 ng/ml of Al. A constant fluorescence intensity is obtained over a wide range (1:50-1:1500) of Al:reagent molar concentrations. Large excesses of over 60 cations, anions and complexing agents (like tartrate, oxalate, phosphate, thio-urea, SCN(-), etc.) do not interfere in the Al determination. The developed method was successfully used in assaying aluminium in several standard reference materials (Al-bronze, brass, stainless steel) as well as in some environmental and biological samples. The method is very precise and accurate (S.D = +/-0.001 on 10 ng/ml; 11 determinations).     

Pre-Column Derivatization HPLC Procedure for the Quantitation of Aluminium Chlorohydrate in Antiperspirant Creams Using Quercetin as Chromogenic Reagent

This article describes the development and validation of a selective high-performance liquid chromatography method that allows, after liquid–liquid extraction and pre-column derivatization reaction with quercetin, the quantification of aluminium chlorohydrate in antiperspirant creams. Chromatographic separation was achieved on an XTerra MS C18 analytical column (150 × 3.0 mm i.d., particle size 5 μm) using a mobile phase of acetonitrile:water (15:85, v/v) containing 0.08 % trifluoroacetic acid at a flow rate of 0.30 mL min^?1. Ultraviolet spectrophotometric detection at 415 nm was used. The assay was linear over a concentration range of 3.7–30.6 μg mL^?1 for aluminium with a limit of quantitation of 3.74 μg mL^?1. Quality control samples (4.4, 17.1 and 30.6 μg mL^?1) in five replicates from five different runs of analysis demonstrated intra-assay precision (% coefficient of variation <3.8 %), inter-assay precision (% coefficient of variation <5.4 %) and an overall accuracy (% recovery) between 96 and 101 %. The method was used to quantify aluminium in antiperspirant creams containing 11.0, 13.0 and 16.0 % (w/w) aluminium chlorohydrate, respectively.     

Spectrophotometric and derivative spectrophotometric determination of aluminium with Hydroxynaphthol Blue

The reaction of aluminium(III) with Hydroxynaphtol Blue (HNB) in aqueous media at apparent pH 5.5 results in a red complex that is stable for at least 4 hr. Beer's Law is obeyed up to 1.6 microg/ml of aluminium(III) with an apparent molar absorptivity of 1.66 x 10(4) l.mol(-1). cm(-1) at 569 nm. This paper proposes procedures for aluminium(III) determination by ordinary and first-derivative spectrophotometry. The results demonstrated that the linear dynamic range is 0.03-1.60 microg/ml for ordinary spectrophotometry and 11.8-320.0 ng/ml for first derivative spectrophotometry. The HNB is not selectivity for aluminium, but the addition of EDTA allows the aluminium determination in the presence of accepted amounts of Ca(II), Mg(II), Mn(II), Ba(II), Sr(II), Cd(II), Pb(II), La(III), In(III), Bi(III) and Zn(II). The interference of Cu(II) and Hg(II) can be masked by thiosulphate. Ions such as UO(2)(II), Mo(VI), Co(II), Ti(IV) and PO(4)(III) do interfere seriously. This method was applied for aluminium determination in copper-base alloy, zinc-base alloy, magnesium-base alloy, iron ore, manganese ore, cement, dolomite, feldspar and limestone. The results indicated high accuracy and precision.     

Extraction chromatographic study of aluminium(III) and mutual separation of aluminium(III), gallium(III), indium(III) and thallium(III) with N-n-octylaniline

A selective method has been developed for extraction chromatographic studies of aluminium(III) and its separation from several metal ions with a chromatographic column containing N-n-octylaniline (liquid anion exchanger) coated on silanized silica gel as a stationary phase. The aluminium(III) was quantitatively extracted with the 0.065 mol/L N-n-octylaninine from 0.013 to 0.05 mol/L sodium succinate at a flow rate of 1.0 mL/min. The extracted metal ion has been recovered by eluting with 25.0 mL of 0.05 mol/L hydrochloric acid and estimated spectrophotometrically with aurintricarboxylic acid. The effects of the acid concentration, the reagent concentration, the flow rate and the eluting agents have been investigated. The log-log plots of distribution coefficient (KdAl(III)) versus N-n-octylaniline concentrationin 0.005 and 0.007 mol/L sodium succinate gave theslopes 0.5 and 0.7 respectively and showed theprobable composition of theextracted species was 1:1 (metal to amine ratio) and the nature of extracted species is [RR''NH2+ Al succinate2-] org. .The extraction of aluminium(III) was carried out in the presence of various ions to ascertain the tolerance limit of individual ions. Aluminium(III) has been separated from multicomponent mixtures, pharmaceutical samples and synthetic mixtures corresponding to alloys. A scheme for mutual separation of aluminium(III), indium(III), gallium(III) and thallium(III) has been developed by using suitable masking agents. The method is fast, accurate and precise.     

Direct determination of silicon in powdered aluminium oxide by use of slurry sampling with in situ fusion graphite-furnace atomic-absorption spectrometry

A direct method for determination of silicon in powdered high-purity aluminium oxide samples, by slurry sampling with in situ fusion graphite-furnace atomic-absorption spectrometry (GF-AAS), has been established. A slurry sample was prepared by 10-min ultrasonication of a powdered sample in an aqueous solution containing both sodium carbonate and boric acid as a mixed flux. An appropriate portion of the slurry was introduced into a pyrolytic graphite furnace equipped with a platform. Silicon compounds to be determined and aluminium oxide were fused by the in situ fusion process with the flux in the furnace under optimized heating conditions, and the silicon absorbance was then measured directly. The calibration curve was prepared by use of a silicon standard solution containing the same concentration of the flux as the slurry sample. The accuracy of the proposed method was confirmed by analysis of certified reference materials. The proposed method gave statistically accurate values at the 95% confidence level. The detection limit was 3.3 microg g(-1) in solid samples, when 300 mg/20 mL slurry was prepared and a 10 microL portion of the slurry was measured. The precision of the determination (RSD for more than four separate determinations) was 14% and 2%, respectively, for levels of 10 and 100 microg g(-1) silicon in aluminium oxide.     

Spectrofluorimetric method for determination of aluminium with chromotropic acid and its application to water samples

A rapid and sensitive method for the trace level determination of aluminium based on the formation of a 1:1 complex with chromotropic acid (1,8-dihydroxynaphthlene-3,6-disulfonic acid) in an methanol medium is reported. The fluorescence intensity of the system was 50 times greater than that of the system without aluminium. This method is very sensitive and selective for the direct determination of aluminium ion. The fluorescence is excited at 346 nm and measured at 370 nm. The optimum conditions are a chromotropic acid concentration of 5.0 ml (1.0x10(-4) M) and pH 4.0+/-0.5 (acetic acid-sodium acetate buffer). The fluorescence intensity is a linear function of the concentration of Al(III) in the range 2-100 ng ml(-1) and the detection limit is 1.0 ng ml(-1). The method has been applied successfully to the determination of trace amount of Al(III) in tap, river and sea-water samples.     

预富集-氢化物发生原子吸收光谱法测定饮料中的痕量铅

原子吸收光谱法测定水样中的痕量元素是应用得最广泛的方法之一[1]。有时需采用多种方法对水样中的痕量元素进行富集。其中一类方法是基于待测元素配合物可以最终定量富集于少量颗粒上,过滤收集这些颗粒,然后制成小体积的、可直接用原子吸收光谱法测定的悬浊液。特定的配位剂分     

Synthesis of 2,4-Dihydroxybenzaldehyde-Isonicotinylhydrazone and Its Fluorescence Reaction with Aluminium

A new fluorescent reagent, 2,4-dihydroxybenzaldehyde-isonicotinylhydrazone (DHBI), is synthesized and characterized by elemental analysis and infrared spectra (KBr disks). The fluorescent reaction of aluminium(III) with the new reagent has been studied. The fluorescent excitation and emission wavelengths of the complex are at 394 and 484 nm, respectively. The optimum pH range is 4.2–4.6; hence the pH is controlled in the optimum interval with a buffer solution (sodium formate–formic acid) of pH 3.3. The linear range of the method is 0–6 μg/25 ml. The molar ratio of aluminium to reagent is found to be 1:1. The proposed method has been used for the determination of trace aluminium in drinking water and edible bicarbonate of sodium with satisfactory results.     

双波长分光光度法测定微量铜

报道了以５－（５－硝基－２－吡啶偶氮）－２－４－二氨基甲苯（５－ＮＯ２－ＰＡ－ＤＡＴ）为显色剂,应用双峰双波长光度法测定铜（Ｉ）的新方法。实验结果表明,在ｐＨ４．０￣ｐＨ６．０的乙酸－乙酸钠缓冲溶液中和盐酸羟胺和乙醇存在下,铜（Ｉ）可与试剂形成稳定的１：２红色配合物。     

Determination of aluminium and its fluoro complexes in natural waters by ion chromatography

Ion chromatography was applied to the determination of aluminium and its fluoro complexes in natural waters. The separation was carried out on a cation-exchange column. The aluminium species were detected by postcolumn reaction with Tiron followed by UV spectrophotometry. The method requires the adjustment of the pH and ionic strength of the sample to those of the mobile phase immediately prior to injection. Al³⁺ , AlF²⁺ and AlF₂⁺ are eluted separately while all hydroxo complexes are readily dissociated and eluted along with Al³⁺ under these conditions. The sum of peak areas, which represents the total aluminium concentration, was conserved whatever the amount of fluoride in the sample. Linearity of calibration was observed over the range 20–2000 μg 1⁻¹. Further, the speciation of fluoro-aluminium complexes as determined experimentally by ion chromatography is in good agreement with calculations based on complexation constants. The applications and limitations of the method are discussed.     

Direct determination of silicon in powdered aluminium oxide by use of slurry sampling with in situ fusion graphite-furnace atomic-absorption spectrometry

A direct method for determination of silicon in powdered high-purity aluminium oxide samples, by slurry sampling with in situ fusion graphite-furnace atomic-absorption spectrometry (GF-AAS), has been established. A slurry sample was prepared by 10-min ultrasonication of a powdered sample in an aqueous solution containing both sodium carbonate and boric acid as a mixed flux. An appropriate portion of the slurry was introduced into a pyrolytic graphite furnace equipped with a platform. Silicon compounds to be determined and aluminium oxide were fused by the in situ fusion process with the flux in the furnace under optimized heating conditions, and the silicon absorbance was then measured directly. The calibration curve was prepared by use of a silicon standard solution containing the same concentration of the flux as the slurry sample. The accuracy of the proposed method was confirmed by analysis of certified reference materials. The proposed method gave statistically accurate values at the 95% confidence level. The detection limit was 3.3 μg g^–1 in solid samples, when 300 mg/20 mL slurry was prepared and a 10 μL portion of the slurry was measured. The precision of the determination (RSD for more than four separate determinations) was 14% and 2%, respectively, for levels of 10 and 100 μg g^–1 silicon in aluminium oxide.