Preconcentration of iron (III), cobalt (II) and copper (II) nitroso-R complexes on tetradecyldimethylbenzylammonium iodide-naphthalene adsorbent

Iron, cobalt and copper form coloured water soluble anionic complexes with disodium 1-nitroso-2-naphthol-3-6-disulphonate (nitroso R-salt). The anionic complex is retained quantitatively as a water insoluble neutral ion associated complex (M-nitroso R-TDBA) on tetradecyldimethylbenzylammonium iodide on naphthalene (TDBA(+)I(-)-naphthalene) packed column in the pH range of: Fe(III): 3.1-6.5, Co: 3.4-8.5 and Cu 5.9-8.0 when their solutions are passed individually over this adsorbent at a flow rate of 0.5-5.0 ml/min. The solid mass consisting of an ion associated metal complex along with naphthalene is dissolved out of the column with 5 ml dimethylformamide/chloroform and metals are determined spectrophotometrically. The absorbance is measured at 710 nm for iron, 425 nm for cobalt and 480 nm for copper. Beers law is obeyed in the concentration range 9.2-82 mug of iron, 425 nm for cobalt cobalt and 3.0-62 mug of copper in 5 ml of final DMF/CHCl(3) solution. The molar absorptivities are calculated to be Fe: 7.58 x 10(3), Co: 1.33 x 10(4) and Cu: 4.92 x 10(4)M(-1)cm(-1). Ten replicate determinations containing 25 mug of iron, 9.96 mug of cobalt and 3.17 mug of copper gave mean absorbances 0.677, 0.450 and 0.490 with relative standard deviations of 0.88, 0.98 and 0.92%, respectively. The interference of large number of metals and anions on the estimations of these metals has been studied. The optimized conditions so developed have been employed for the trace determination of these metals in standard alloys, waste water and fly ash samples.     

Preconcentration of trace nickel with the ion pair of disodium 1-nitroso-2-naphthol-3,6-disulfonate and tetradecyldimethylbenzylammonium chloride on microcrystalline naphthalene or by the column method and determination by third derivative spectrophotometry

Nickel is quantitatively retained by disodium 1-nitroso-2-naphthol-3,6-disulfonate (nitroso-R salt) and tetradecyldimethylbenzylammonium chloride (TDBA(+)Cl(-)) on microcrystalline naphthalene in the pH range 5.4-12.1 from large volumes of aqueous solutions of various alloys and biological samples. After filtration, the solid mass consisting of the nickel complex and naphthalene was dissolved with 5 ml of dimethylformamide (DMF) and the metal was determined by third derivative spectrophotometry. Nickel complex can alternatively be quantitatively adsorbed on tetradecyldimethylbenzylammonium-naphthalene adsorbent packed in a column and determined similarly. The detection limit is 10 ppb (signal to noise ratio 2) and the calibration curve is linear from 30 to 5.4x10(3) ppb in dimethylformamide solution with a correlation coefficient of 0.9997 by measuring the distance d(3)A/dlambda(3) between lambda(1) (537 nm) and lambda(2) (507 nm). Eight replicated determinations of 2.5 mug of nickel in 5 ml of dimethylformamide solution gave a mean intensity (peak-to-peak signal between lambda(1) and lambda(2)) of 0.339 with a relative standard deviation of +/-0.87%. The sensitivity of the method is 0.677 ml/mug found from the slope (d(3)A/dnm(3)) of the calibration curve. Various parameters such as the effect of pH, volume of aqueous phase and interference of a number of metal ions on the determination of nickel has been studied in detail to optimize the conditions for nickel determination in various alloys and biological samples.     

Tetradecyldimethylbenzylammonium thiocyanate adsorbent supported on naphthalene for the preconcentration and determination of cobalt in aluminium alloys and steels using atomic absorption spectrometry

A solid ion-pair material produced from tetradecyldimethylbenzylammonium chloride (TDBA) and ammonium thiocyanate on naphthalene provides a simple, rapid and selective technique of preconcentrating cobalt from up to 200 ml of aqueous solution. Cobalt reacts with sodium 1-nitroso-2-naphthol-3,6-disulphonate (nitroso-R salt) to form a brown, water-soluble chelate anion. The chelate anion forms a water-insoluble Co-nitroso-R salt-TDBA complex on naphthalene packed in a column and trace cobalt is quantitatively retained on the naphthalene in the pH range 2.7–11.0 at a flow-rate of 2 ml min^?1. The solid mass is stripped from the column with 5 ml of dimethylformamide (DMF) and cobalt is measured by atomic absorption spectrometry (AAS) at 241 nm. The calibration graph is linear over the concentration range 0.5–15μg Co in 5 ml of dimethylformamide solution. Seven replicate determinations of 9 μg of cobalt gave a mean absorbance of 0.095 with a relative standard deviation of 1.7%. The sensitivity for 1% absorption was 0.0834μg ml^?1 (0.240 μg ml^?1 for direct AAS on the aqueous solution). The proposed method was utilized for the determination of cobalt in standard aluminium alloys and steel samples.     

Column chromatographic preconcentration of palladium in alloys with 9,10 phenanthrenequinonemonoxime-naphthalene

A solid chelating compound phenanthrenequinonemonoxime (PQM) supported on naphthalene provides a rapid, sensitive and economical means of preconcentration and separation of palladium from standard solutions and from synthetic samples. Palladium forms a complex with PQM supported on naphthalene in a column at pH 2.2-5.4 with a flow-rate of 1 ml/min. The metal complex and naphthalene are dissolved out from the column with 5 ml of CHCl(3) and the absorbance is measured at 430 nm or 500 nm against a reagent blank. Beers law is obeyed in the concentration range 3.0-56.0 mug and 6.0-42.0 mug at 430 nm and 500 nm respectively. The molar absorptivities are 2.10 x 10(4) and 1.69 x 10(4) 1.mole(-1).cm(-1) at 430 and 500 nm respectively.     

Ammonium tetraphenylborate-naphthalene adsorbent for the preconcentration and trace determination of iron in alloys and biological samples using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol by third derivative spectrophotometry

A solid ion-pair material produced from ammonium tetraphenylborate on naphthalene (ATPB-naphthalene) provides a simple, rapid, economical and selective technique for preconcentrating iron from approximately 500 ml of aqueous solution of standard alloys and biological samples. Iron reacts with 2-(5-bromo-2-pryidlazo)-5-diethylaminophenol (5-Br-PADAP) to form a water-soluble cationic complex. When the aqueous solution of this cationic species in the pH range 3.2-8.5 is passed over the adsorbent ATPB-naphthalene at a flow rate of 1 ml min(-1), it is quantitatively retained on naphthalene as an uncharged ion-associated complex. The solid mass from the column was dissolved out with 5 ml of dimethylformamide (DMF) and iron is determined by third derivative spectrophotometry by measuring the signal d(3)A/ dlambda(3) between lambda(2)(773 nm) and lambda(3)(737 nm). The calibration curve is linear over the concentration range 0.10-25.0 mug of iron in 5 ml of DMF solution. Eight replicate determinations of 5 mug of iron gave a mean intensity (peak-to-peak signal between lambda(2) and lambda(3)) of 1.534 with a relative standard deviation of 0.90%. The sensitivity of the method is 0.307 (d(3)A/dnm(3) )/mug found from the slope of the calibration curve. The interference of a large number of anions and cations has been studied and the optimized conditions developed were utilized for the trace determination of iron in various standard alloys and biological samples.     

Determination of trace levels of manganese in various biological and environmental samples by atomic absorption spectrometry after solid-liquid extraction and preconcentration with the ion pair formed by the nitroso-S anion and the tetradecyldimethylbenzylammonium cation.

Manganese is quantitatively retained by 2-nitroso-1-naphthol-4-sulfonic acid (nitroso-S) and tetradecyldimethylbenzylammonium (TDBA) chloride on microcrystalline naphthalene in the pH range 9.5-10.6 from large volumes of aqueous solutions of various samples. After filtration, the solid mass consisting of the manganese complex and naphthalene is dissolved in 5 mL dimethylformamide and the metal is determined by flame atomic absorption spectrometry. Alternatively, the manganese complex can be quantitatively adsorbed on TDBA-naphthalene adsorbent packed in a column and determined similarly. About 0.2 microg manganese can be concentrated in a column from 400 mL aqueous sample with a concentration as low as 0.5 ng/mL. Eight replicate determinations of manganese at 0.8 microg/mL gave a mean absorbance of 0.156 for the final solution with a relative standard deviation of 1.4%. The sensitivity for 1% absorption was 23 ng/mL. The interference of a large number of anions and cations was studied, and the optimized conditions developed were used for trace determinations of manganese in various alloys, and in biological and environmental samples.     

Column preconcentration of trace manganese with the ion pair of 2-nitroso-1-naphthol-4-sulfonic acid tetradecyldimethylbenzyl-ammonium chloride supported on naphthalene and determination by derivative spectrophotometry

A column preconcentration method has been developed for the determination of trace amounts of manganese by preconcentration on 2-nitroso-1-naphthol-4-sulfonic acid (nitroso-S)-tetradecyldimethylbenzylammonium (TDBA) naphthalene as an adsorbent using a simple funnel tipped glass tube. Manganese reacts with nitroso-S to form a water soluble brown colored chelate anion. The chelate anion forms a water insoluble Mn-Nitroso-S-TDBA ion pair on naphthalene packed in a column in the pH range 9.6-10.5 at a flow rate of 1-2 ml/min. The solid mass consisting of manganese complex and naphthalene is dissolved in 5 ml of dimethylformamide (DMF) and the metal determined by second derivative spectrophotometry. The calibration curve is linear in the concentration range 0.25-35.0 micrograms of Mn in 5 ml of the final DMF solution. Eight replicate determinations of 25 micrograms of standard manganese solution give a mean peak height of 4.0 with a correlation coefficient of 0.9995 and relative standard deviation of +/- 1.1%. The sensitivity was calculated to be 0.502(d2 A/d lambda 2)/microgram ml-1 from the slope of the calibration curve. The detection limit was 0.020 microgram ml-1 for manganese at the minimum instrumental settings (signal to noise ratio = 2). Various parameters effecting the method such as the effect of pH, volume of aqueous phase and interference of a number of metal ions on the determination of manganese have been evaluated to optimize the conditions for its determination in standard alloys and biological samples.     

Determination of palladium with thiocyanate and rhodamine b by a solvent-extraction method

Sensitive spectrophotometric and spectrofluorimetric procedures for the determination of palladium have been developed, based on solvent-extraction of the ion-pair formed between Rhodamine B and the anionic complex of Pd(II) with thiocyanate. With an organic to aqueous phase-volume ratio of 1:5, the molar absorptivity is 9.0 x 10(4) l.mole(-1).cm(-1) and the absorbance of the reagent blank is 0.026. Spectrophotometrically, palladium can be determined in the range 0.1-8.8 mug. Spectrofluorimetrically, it can be determined over the range 0.04-1.5 mug. The spectrophotometric procedure has been applied to the determination of palladium in dental alloys, organopalladium compounds and hydrogenation catalysts.     

Extraction and spectrophotometric determination of titanium(IV) with malachite green and p-chloromandelic acid, with application to mild steels

A very sensitive, selective and simple method for extraction and spectrophotometric determination of titanium(IV) with an alpha-hydroxy acid has been developed. p-Chloromandelic acid reacts with titanium in weakly acidic aqueous solution at room temperature to form a complex anion extractable into chlorobenzene with Malachite Green as counter-ion. Titanium is determined indirectly by measuring the absorbance of Malachite Green in the extract at 630 nm. The calibration graph is linear for titanium(IV) over the range 0.25-7.5muM (0.05-1.44 mug); the apparent molar absorptivity is 1.31 x 10(5) l.mole(-1).cm(-1). The method has been successfully applied to the determination of titanium in mild steels.     

Solid-liquid extraction and preconcentration of trace nickel using 2-nitroso-1-naphthol-4-sulfonic acid (Nitroso-S) and TDBA onto benzophenone and determination by atomic absorption spectrometry.

Nickel was quantitatively retained by 2-nitroso-1-naphthol-4-sulfonic acid (Nitroso-S) and tetradecyldimethylbenzylammonium chloride (TDBA Cl) onto benzophenone in the pH range 5.0-6.0 from large volumes of aqueous solutions of various samples. After filtration, each solid mass consisting of a nickel complex and benzophenone was dissolved with 5 ml of dimethylformamide (DMF) and the metal was determined by atomic absorption spectrometry (AAS). About 0.6 microg of nickel could be concentrated from 200 ml of an aqueous sample, where its concentration was as low as 3.0 ng/ml. Eight replicate determinations of 2.5 microg/ml of nickel in the final DMF solution gave a mean absorbance of 0.112 with a relative standard deviation of 1.9%. The sensitivity for 1% absorption was 98 ng/ml. The interference of a number of anions and cations was studied and the developed optimized conditions were utilized for the trace determination of nickel in various alloys and biological samples.     

Rapid, selective, direct and derivative spectrophotometric determination of titanium with 2,4-dihydroxybenzaldehyde isonicotinoyl hydrazone

A simple and sensitive spectrophotometric method is developed for the determination of titanium in aqueous medium. The metal ion forms a reddish brown coloured complex with 2,4-dihydroxybenzaldehyde isonicotinoyl hydrazone (2,4-DHBINH) in the pH range 1-7. The complex shows two absorption maxima, one at 430 nm and the other at 500 nm. The reagent shows appreciable absorbance of 430 nm and negligible absorbance at 500 nm at pH 1.5. Beer's law is obeyed in the range 0.09 to 2.15 mug ml(-1) of titanium(IV). The molar absorptivity and the Sandell's sensitivity of the method are 1.35 x 10(4) 1 mol(-1) cm(-1) and 0.0049 mug cm(-2), respectively. A method for the determination of titanium by first-order derivative spectrophotometry is also proposed. The methods have been employed successfully for the determination of titanium in several alloy and steel samples.     

Preconcentration of trace cobalt with the ion pair of 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol and tetraphenylborate onto microcrystalline naphthalene or column method and its determination by derivative spectrophotometry

Cobalt-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP)-tetraphenylborate ion associated complex is quantitatively adsorbed on microcrystalline naphthalene in the pH range 3.5-9.5 from a fairly large volume of the aqueous samples (preconcentration factor ~30). After filtration, the solid mass consisting of the cobalt complex and naphthalene was dissolved with 5 ml of dimethylformamide (DMF) and the metal determined by first-derivative spectrophotometry. The cobalt-5-Br-PADAP complex can alternatively be quantitatively retained on ammonium tetraphenylborate-naphthalene adsorbent filled in a column (preconcentration factor 120) in the same pH range and determined similarly. The detection limit is 30 ppb (signal-to-noise ratio=2) and the calibration curve is linear over 0.3-8.0 mug of cobalt in 5 ml of the final DMF solution. Eight replicate determinations of 1.0 mug of cobalt gave a mean peak height of 0.208 (at 611.5 nm) with a relative standard deviation of 1.2%. The sensitivity of the method is 1.04 (dA/dnm) ml mug(-1) found from the slope of the calibration curve. The interference of a large number of anions and cations on the determination of cobalt has been studied and the optimized conditions developed were utilized for its trace determination in various standard alloys and biological samples.     

Application of 1,2-Dihydroxybenzene-3,5-disulfonic Acid for the Separation and Preconcentration of Trace Molybdenum and Its Determination by Third Derivative Spectrophotometry

Molybdenum was quantitatively extracted form large volumes of aqueous solutions of various samples by 1,2-dihydroxybenzene-3,5-disulfonic acid (Tiron) and tetradecyldimethylbenzylammonium chloride (TDBA) on microcrystalline naphthalene in the pH range 6.5–8.5. After filtration, the solid residue consisting of molybdenum complex and naphthalene was dissolved in 5 mL of chloroform and molybdenum was determined by third derivative spectrophotometry. Alternatively, molybdenum can be quantitatively adsorbed on Tiron-TDBA-naphthalene adsorbent packed in a column and determined in a similar manner. About 0.02 µg of molybdenum can be concentrated in a column from 500 mL of aqueous sample, where its concentration is as low as 0.04 ng/mL. Various parameters such as the effect of pH, the volume of the aqueous phase, and the interference of a number of metal ions with the determination of molybdenum have been studied in detail to optimize the analysis of standard alloys and biological samples.__________From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 7, 2005, pp. 698–702.Original English Text Copyright © 2005 by Mohammad Ali Taher, Sayed Ziae Mohammadi Mobarakeh.The text was submitted by the authors in English.     

Reversed phase HPLC determination of titanium(IV) and iron(III) with sodium 1,2-dihydroxybenzene-3,5-disulfonic acid

A highly sensitive method has been developed for the determination of titanium(IV) and iron(III) by ion-pair reversed phase liquid chromatography using sodium 1,2-dihydroxybenzene-3,5-disulfonic acid (Tiron) as a precolumn chelating reagent. The metal - Tiron chelates were separated on a C₁₈ (ODS) column; the mobile phase was a 2:8 (v/v) mixture of acetonitrile and acetate buffer (0.04 mol/L, pH 6.2) containing 2.0 × 10^?3 mol/L Tiron, 0.04 mol/L tetrabutylammonium bromide, and 0.1 mol/L potassium nitrate. The detection limits for titanium(IV) and iron(III) are 0.5 and 2.0 μg/L, respectively. The method has been applied to the simultaneous determination of titanium(IV) and iron(III) in river water samples and has furnished highly precise results.     

Malachite green as a reagent for detection and spectrophotometric determination of chromium(VI)

A sensitive and inexpensive method of spectrophotometric determination of chromium(VI), based on the absorbance of its complex with malachite green and acetic acid at pH 2.5 is reported. The complex shows a molar absorptivity of 8 x 10(4) l.mole(-1) cm(-1) at 560 nm, using malachite green and acetic acid as reference solution. The effect of time, temperature, pH and reagent concentration is studied and optimum operating conditions are established. Beer's law is applicable in the concentration range 2.0-22.8 mug/ml chromium(VI). The resin beads act as a catalyst and as little as 1.6 mug of chromium(VI) is detected in the resin phase as compared to 4.1 mug in the solution phase. The standard deviation in the determinations is +/-0.40 mug/ml for a 10.35 mug/ml solution.     

Spectrophotometric determination of chromium(III) and rhodium(III) after extraction with oxine into molten naphthalene

Conditions have been developed for the extraction of chromium(III) and rhodium(III) as their 8-hydroxyquinolinates into molten naphthalene. The naphthalene is allowed to solidify, separated by filtration, dried with filter paper and dissolved in chloroform. The solution is diluted to 10 ml and its absorbance measured at 410 nm for chromium and 425 nm for rhodium, against a reagent blank. In both cases the solution is stable for 24-36 hr. Beer's law is obeyed over the range of 2.7-48.6 mug of chromium or 2.7-57.5 mug of rhodium in 10 ml of the chloroform solution. The molar absorptivity is 3 x 10(3) l. mole(-1) . cm(-1) for chromium and 3.6 x 10(4) for rhodium. Solutions containing 27.0 mug of chromium or 10.95 mug of rhodium give a mean absorbance of 0.140 and 0.395 respectively, with standard deviations of 0.002(2) and 0.004(7). Most metal ions that form oxinates may interfere, but can be removed beforehand by normal liquid-liquid extraction.     

Extraction and spectrophotometric determination of molybdenum(VI) with Malachite Green and p-chloromandelic acid

Molybdenum(VI) reacts with p-chloromandelic acid to form a complex extractable into chlorobenzene with Malachite Green, from aqueous solution at pH 2.0-4.0 at room temperature, and can then be determined indirectly by measuring the absorbance of the Malachite Green in the extract, at 630 nm. The calibation graph is linear for molybdenum over the range 0.26-10.0 x 10(-6)M (0.10-4.0 mug); the apparent molar absorptivity is 1.06 x 10(5) l.mole(-1).cm(-1). The method has been applied to the determination of molybdenum in mild steels with satisfactory results.     

Spectrophotometric determination of iron(III) dimethyldithiocarbamate (ferbam)

A spectrophotometric method was developed for the determination of ferbam (iron(III) dimethyldithiocarbamate) by converting it into an iron-phenanthroline complex, which was then absorbed on microcystalline naphthalene in the presence of tetraphenylborate, and the absorbance was measured at 515 nm against a reagent blank. The molar absorptivity of the complex was 1.2 x 10(4)l mol(-1)cm(-1). Ten replicate analyses of a sample solution containing 150 mug of ferbam gave a relative standard deviation of 0.84%. Beer's law was obeyed over the concentration range 22.4-372.9 mug of ferbam. The effects of various factors such as reagent concentration and naphthalene, shaking time and diverse ions were studied in detail. The method is sensitive and selective and can be applied to the direct determination of ferbam in commercial samples and in mixtures containing various other dithiocarbamates (e.g. ziram, zineb and maneb) in foodstuffs.     

Rapid spectrophotometric determination of palladium in titanium alloys with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)phenol

A rapid spectrophotometric method for the determination of Pd in titanium alloys is proposed. It is based on the reaction of 2-(5-bromo-2-pyridylazo)-5-(diethylamino)phenol with Pd(II) in a sulphuric acid medium in the presence of ethanol. Beer's law is obeyed up to 40 mug of Pd. The molar absorptivity is 4.5 x 10(4) 1.mole(-1).cm(-1). The standard deviation is 0.3 mug of Pd and the coefficient of variation varies from 0.8 to 3.3%. The elements ordinarily present in such alloys do not interfere. High selectivity is achieved by using fluoroboric acid as masking agent. Improvements in the method of sample decomposition also contribute to the rapidity of the method.     

Spectrophotometric determination of titanium with N-m-Tolyl-N-phenylhydroxylamine and its application to environmental samples

N-m-Tolyl-n-phenylhydroxylamine is proposed for the spectrophotometric determination of titanium. The reagent forms a yellow chloroform-soluble complex with titanium in media with a hydrochloric acid concentration of at least 9M. The apparent molar absorptivity at 380 nm is 7.4 x 10(3) 1.mole(-1).cm(-1). The optimum final concentration range is 0-54 mug of titanium in 10 ml of chloroform. The complex contains the metal and reagent in 1:2 ratio. The proposed method has been successfully applied to the determination of titanium in coal, coal fly-ash, pond sediment and asphalt.