Investigations on Adsorption Potentiometry Part V Derivative Adsorption Chronopotentiometry of Beryllium(II)-4-[(4-diethylamino-2-hydroxypheanyl)-azo]-5-hydroxy-naphthalene-2,7-disurphonic Acid System

Abstract

An electroanalytical methood, based on derivative chronopotentiometry of the complex of beryllium(II) with 4-[(4-diethylamino-2-hydroxy-phenyl)-azo]-5-hydroxy-naphthalene-2,7-disurphonic acid (Beryllon II) accumulated adsorptively on the surface of a hanging mercury drop electrode, has been developed for determining trace beryllium in food. The dependences of the peak height on the dt/dE vs. E curve on the pre-concentration time, preconcentration potential and the constant reducing current are discussed. In 0.15 mol/1 NH_s+0.05 mol/1 NH₄Cl, 4×10^?7 mol/l Beryllon II, and at a preconcentration potential of -0.30 V (ve. SCE), the limit of detection and linear range are 1 × l0^?10 mol/l and 3 × 10^?10 -2 × l0^?7 mol/l, Iwpectively. The relative standard error of the method is 2.3% for 6 × 10^?8 mol/l Be(II). The method WBB applied to samples of food. The electrode procees hae been diecueeed.     

Adsorptive preconcentration for voltammetric measurements of trace levels of zirconium

This paper describes an electrochemical stripping procedure for ultratrace measurements of zirconium, in which preconcentration is achieved by the adsorption of a zirconium-Solochrome Violet RS complex onto a hanging mercury drop electrode. Cyclic voltammetry was used to characterize the interfacial and redox behaviour. For a 10-min preconcentration time, the detection limit found was 2.3 x 10(-10)M. Optimal experimental conditions were found to be use of a stirred acetate buffer (pH 4.6) solution with Solochrome Violet RS concentration 1.5 x 10(-6)M, a preconcentration potential of -0.3 V and linear scan mode. A 60-fold enhancement of the response is obtained following 5-min preconcentration. With preconcentration for 60 sec, calibration plots for zirconium are linear for the 1.1 x 10(-8)-1.1 x 10(-7)M range. The relative standard deviation at 5.5 x 10(-8)M is 1.7%. Possible interferences by surface-active organic materials and other trace metals have been investigated. Zirconium added to a sea-water sample at the 10 ng/ml level was readily determined.     

Ultrasensitive and selective measurements of tin by adsorptive stripping voltammetry of the tin-tropolone complex

Trace levels of tin can be determined by voltammetry after controlled adsorptive preconcentration of the tin-tropolone complex on a hanging mercury drop electrode. The resulting adsorptive stripping procedure offers better sensitivity and selectivity than conventional stripping methods for tin. Optimal conditions include 4 x 10(-6)M tropolone in a stirred acetate buffer (pH 4.0), a preconcentration potential of -0.40 V, and differential-pulse stripping. For an 8-min preconcentration period, the detection limit is 2.3 x 10(-10)M (28 ng/l.). Linear calibration plots of i(p)vs. C are obtained at low concentrations, with linear plots of 1/i(p)vs. 1/C at high concentrations. The relative standard deviation (at the 6-mug/1. level) is 2.6%. The response is not affected by the presence of lead, cadmium, indium and thallium, which commonly interfere severely in analogous anodic stripping measurements. Results are reported for river and orange-juice samples.     

Trace adsorptive voltammetric determination of antimony in hair

A very sensitive electrochemical procedure for trace determination of antimony is described. The complex of antimony with p-dimethyl-aminophenyl-fluorone (p-DMPF) is adsorbed on a hanging mercury drop electrode (HMDE), and the reduction current of the accumulated complex is measured by voltammetry. In linear sweep voltammetry, the reduction potential of the complex is more positive than that of the free dye. The peak height of the complex is proportional to the concentration of antimony in the range of 4.0 x 10(-9) to 4.0 x 10(-7) M, the detection limit is 1.0 x 10(-9) M Sb(III) for a 5 min preconcentration time. The relative standard error for the determination of 8.0 x 10(-8) M Sb(III) is 2.9%.     

Cyclopentanone thiosemicarbazone, a new complexing agent for copper determination in biological samples by adsorptive stripping voltammetry.

A selective and sensitive stripping voltammetric method for the determination of trace amounts of copper(II) with cyclopentanone thiosemicarbazone (CPTSC) is presented. The method is based on the adsorptive accumulation of the resulting copper-CPTSC complex on a hanging mercury drop electrode, followed by the stripping voltammetric measurements at the reduction current of the adsorbed complex at -0.37 V vs. Ag/AgCl. The optimal conditions for the stripping analysis of copper include pH 9.3, deposition time of 120 s, and a deposition potential of -0.1 V (vs. Ag/AgCl). The peak current is linearly proportional to the copper concentration over a range 3.14 x 10(-9) M to 1.57 x 10(-6) M with a limit of detection of 1.57 x 10(-9) M. The technique has been applied to the determination of copper in biological samples, like urine and whole blood.     

Investigations on adsorption potentiometry Part I. Derivative adsorption chronopotentiometry of the iron(III)-2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol system

An electroanalytical method, based on derivative chronopotentiometry of the iron complex with 2-(5′-bromo-2′- pyridylazo)-5-diethylaminophenol (5-Br-PADAP) accumulated adsorptively on the surface of a hanging mercury drop electrode, for determining trace iron in food has been developed. The dependences of the peak height on the dt/dE vs. E curve on the preconcentration time, preconcentration potential and electrode area are discussed. Optimum experimental conditions include 0.005 mol 1^?1 NH₃NH₄Cl, 2 × 10^?7 mol 1^?1 5-Br-PADAP and a preconcentration potential of ?0.40 V (vs. SCE). Under these conditions, the detection limit and the linear range are 2 × 10^?9 and 6.7 × 10^?9?1.7 × 10^?7 mol 1^?1, respectively. The relative standard error of the method is 1.5% for 6.7 × 10^?8 mol 1^?1 Fe(III). The method was applied to samples of microwave digested food.     

Trace analysis of aluminum in natural waters with rubeanic acid by adsorption chronopotentiometry

The determination of trace levels of aluminum in natural waters with rubeanic acid (RA) by adsorption chronopotentiometry is developed in this paper. Optimum experimental conditions include an accumulation potential of -0.40 V, accumulation time of 60 s, and a RA concentration of 6x10(-6) M in 0.2 M NaAc-HAc buffer solution (pH 4.6). The response is linear over the 1x10(-8) approximately 4x10(-7) M concentration range. The detection limit is 5.6x10(-9) M and the relative S.D. (at the 3x10(-7) M level) is 2.6%. Possible interferences are evaluated. The method has been applied to the determination of trace levels of Al in various real samples. Direct determination of toxic forms of Al in surface waters by this technique is also explored.     

Differential pulse anodic stripping voltammetric determination of lead(II) with a 1,4-bis(prop-2'-enyloxy)-9,10-anthraquinone modified carbon paste electrode

A sensitive and selective method for the determination of lead(II) with a 1,4-bis(prop-2'-enyloxy)-9,10-anthraquinone (AQ) modified carbon paste electrode has been developed. The method is based on non-electrolytic preconcentration via complex formation with modifier, followed by an accumulation period with a negative potential (-1.5 V), and then by a proper anodic stripping. The analytical performance was evaluated with respect to the quantity of modifier in the paste, concentration of electrolyte solution, preconcentration time, lead(II) concentration, and other variables. A linear calibration graph was obtained in the concentration range 2.00x10(-9)-1.06x10(-5) M Pb(II) (n=21, r=0.9999) with 30 s preconcentration time. The detection limit was found to be 1x10(-9) M. For eight preconcentration/determination cycles, the differential pulse voltammetric response was reproduced with 5.0 and 3.7% relative standard deviations at 2.00x10(-8) and 2.00x10(-6) M Pb(II), respectively. Rapid and convenient renewal of electrode surface allows the use of a single modified electrode surface in multiple analytical determinations over several weeks. Many coexisting metal ions had little or no effect on the determination of lead(II). The developed method was applied to lead determination in waste waters.     

Chemical reduction and spectrophotometric determination of silver, copper and nickel

Silver(I), copper(II) and nickel(II) can be reduced to the metallic state by formaldehyde at pH 11, chromium(II) in 2.5M sulphuric acid, and borohydride at pH 5.5-6.0, respectively. Reoxidation of these metals with iron(III) in the presence of Ferrozine enables their determination at concentration below 1 mug/ml by measurement of the absorbance of the iron(II)-Ferrozine complex at 562 nm, with a precision better than 3%. The apparent molar absorptivities for silver, copper and nickel are 2.78 x 10(4), 5.56 x 10(4) and 5.58 x 10(4) l.mole(-1).cm(-1), respectively. The average thickness of silver films on glass surfaces can be determined in the way.     

A sensitive and specific method for isoniazid determination based on selective adsorption using an isoniazid ion-selective piezoelectric sensor

A selective, sensitive and simple ion-selective piezoelectric (ISP) sensor was developed for the direct determination of isoniazid (INH) in body fluids. Based on sensitive mass response of piezoelectric quartz crystal and selective adsorption/desorption across the modified film, the ISP sensor was fabricated by coating a PVC film containing activant on one electrode of a thickness-shear mode piezoelectric quartz crystal. The observed frequencies of ISP sensor were found to decrease with the increase of the INH concentration in a 0.1 M NaNO(3) solution. In this paper, three activants, INH-phosphotungstate (I), INH-silicotungstate (II), and INH-[BiI(4)](-) (III), were synthesized and investigated. Calibration graphs were linear from 6x10(-8) to 2x10(-3) M for I, 2x10(-7) to 2x10(-3) M for II and 2x10(-7) to 2x10(-3) M for III, with detection limits 6x10(-8) M for I, 2x10(-7) M for II and 2x10(-7) M for III, in a 0.1 M NaNO(3) solution at pH 7.0 and 37 degrees C. Recoveries were from 98% to 102% with R.S.D. up to 2%. Results for real samples obtained by the proposed method agreed well with those obtained by the conventional pharmacopeia method.     

Polarographic determination of fluoride using the adsorption wave of the Ce(III)-alizarin complexone-fluoride complex

A very sensitive electrochemical method for trace measurement of fluoride in water is discussed. The complex of cerium(III) with alizarin complexone (ALC) and fluoride ion is adsorbed at the dropping mercury electrode. In cathodic sweeps, the peak height is directly proportional to the concentration of fluoride over the range 8 x 10(-8)-5 x 10(-6)M (1.5 x 10(-9)-9.5 x 10(-8) g/ml), and the detection limit is 5 x 10(-8)M (9.5 x 10(-10) g/ml). The proposed method was applied to the determination of fluoride in water.     

Polarographic determination of indium(III) after salting-out extraction of the bromide complex into acetonitrile

A simple and sensitive method has been developed for the polarographic determination of indium(III) after solvent extraction into acetonitrile, salted-out from aqueous solution with sodium bromide. The extracted indium(III)-bromide complex gives a well-defined d.c. wave with E(1 2 ) = -0.69 V vs. SCE. The wave-height is directly proportional to the concentration of indium(III) from 1.6 x 10(-6) to 3.0 x 10(-4)M with respect to the original aqueous solution. In the a.c. polarographic method, a linear calibration curve is obtained for indium(III) over the concentration range from 1.6 x 10(-6) to 1.5 x 10(-5)M, and interference from most foreign ions can be eliminated. In particular, 10.0 mg of Fe(III) and 2.5 mg of Tl(III) are tolerated when 1.0 g of ascorbic acid is added. The lower limit of determination is 8 x 10(-8)M indium(III) by the square-wave polarographic method.     

Complex formation constants for the aqueous copper(I)-acetonitrile system by a simple general method

A simple spectrophotometric method for the evaluation of formation constants for aqueous copper(I) has been developed, based on the kinetics of reduction of Co(III)(NH(3))(5)X complexes. The method has been applied to the aqueous copper(I)-acetonitrile system to determine the successive formation constants beta(1), beta(2), and beta(3) as 4.3 x 10(2) M(-)(1), 1.0 x 10(4) M(-)(2), and 2.0 x 10(4) M(-)(3), respectively, in 0.14 M NaClO(4)/HClO(4) at 21 +/- 1 degrees C.     

Determination of trace thorium using catalytic-adsorptive stripping voltammetry of the thorium-cupferron complex

A sensitive stripping voltammetric procedure for trace measurement of thorium, based on the catalytic-adsorptive peak of the thorium-cupferron complex, is reported. Optimal experimental conditions include the use of 1mM BES buffer solution (pH 5.5), containing 20muM cupferron, an accumulation potential of -0.80 V (vs. Ag/AgCl), and a differential pulse potential scan. The resulting stripping procedure offers improved sensitivity over a previous stripping scheme for thorium. The limit of detection after 5 min preconcentration is 50 ng/l. (2 x 10(-10)M), the response is linear up to 8 x 10(-8)M, and the relative standard deviation at the 2.1 x 10(-8)M level is 4.4%. Possible interferences are evaluated.     

Determination of molybdenum in the presence of 2-(2-benzothiazolylazo)-p-cresol by catalytic-adsorptive stripping voltammetry

The adsorptive collection of the molybdenum (VI) complexed with 2-(2-benzothiazolylazo)-p-cresol (BTAC) coupled with the catalytic current of the adsorbed complex at a static mercury drop electrode yields an ultrasensitive voltammetric procedure for the determination of molybdenum. Optimal experimental conditions were: a stirred acetate buffer 0.2 M (pH 3.5) as supporting electrolyte, a BTAC concentration of 1.0 x 10(-6) M as ligand, and a concentration of 0.1 M potassium nitrate as the oxidizing agent. In addition, a preconcentration potential of -0.080 V vs Ag/AgCl (3 M KCl), equilibration time of 15 s, a frequency of 30 Hz, a scan increment of 2 mV, a pulse amplitude of 0.050 mV, and a drop area of 0.032 cm2 were used. The cyclic voltammogram was recorded using a staircase wave with a scan rate of 100 mV/s. The forward scan starts at the initial potential of -0.080 V and is reversed at -0.90 V. Using the catalytic current at approximately -0.55 V the response to the Mo(VI) was found to be linear over a concentration range of 1.0-10.0 microg/L. The limit of detection is as low as 6.2 x 10(-10) M with 4 min of preconcentration time. The possible interference of other trace ions was investigated. The merits of this procedure are demonstrated using of reference samples.     

Single-sweep polarography of the copper(II)-3-hydroxy-1-p-sulphonatophenyl-3-phenyltriazene complex and its analytical applications

A polarographic investigation of the copper-3-hydroxy-1-p-sulphonatophenyl-3-phenyltriazene (HSPT) complex in 0.05 M sodium tetraborate medium is described and a simple and sensitive single-sweep polarographic method for the determination of trace amounts of copper in biological samples is proposed. The complex was shown to be Cu(HSPT)2 with log beta' = 11.38. The polarographic wave is caused by the reduction of copper(II) in the adsorbed complex to copper amalgam on the surface of a mercury electrode. The current peak is directly proportional to the concentration of copper in the range 8.0 x 10(-9)-4.0 x 10(-6) M and the detection limit is 5.0 x 10(-9) M.     

The stabilization of managese(III) by azide ions in aqueous solution

The evidences of spontaneous oxidation of Mn(II) by the dissolved oxygen in azide buffer medium, which is dependent on the N (-)(3)HN (3) concentration, suggested a formation of stable Mn(III) complexes due to marked colour changes. Spectrophotometric studies combined with coulometric generation of Mn(III), in presence of large excess of Mn(II), showed a maximum absorbance peak at 432 nm. The molar absorptivity increases with azide concentration (0.44-3.9 mol 1(-1)) from 3100 to 6300 mol(-1) 1 cm(-1), showing a stepwise complex formation. Potential measurements of the Mn(III) Mn(II) system in several azide aqueous buffers solutions: 1.0 x 10(-2) mol 1(-1) HN(3), (0.50-2.0 mol 1(-1)) N(-)(3) and 5.0 x 10(-2) mol 1(-1) Mn(II) and constant ionic strength 2.0 mol 1(-1), kept with sodium perchlorate, leads to the conditional potential, E(0')x, in several azide concentrations at 25.0 +/- 0.1 degrees C. Considering the overall formation constants of Mn(II) N (-)(3), from former studies, and the potential, E(0')s = 1.063 V versus SCE, for Mn(III) Mn(II) system in non-complexing media, it was possible to calculate the Fronaeus function, F(0)(L), and the following overall formation constants: beta(1) = 1.2 x 10(5) M(-1), beta(2) = 6.0 x 10(8) M(-2), beta(3) = (2.4 +/- 0.7) x 10(11) M(-3), beta(4) = (1.5 +/- 0.5) x 10(11) M(-4) and beta(5) = (9.6 +/- 0.8) x 10(11) M(-5) for the Mn(III) N (-)(3) complexes. These data give important support to understand the importance of Mn(II) and Mn(III) synergistic effect on the analytical method of S(IV) determination based on the Co(II) autoxidation.     

Ultratrace determination of adenine in the presence of copper by adsorptive stripping voltammetry

An electrochemical stripping procedure for ultra-trace measurements of adenine is described based on the adsorption of the adenine-copper complex on a static mercury drop electrode. Cyclic voltammetry was used to characterize the interfacial and redox behavior. Optimum experimental conditions were found when using a 0.005 M NaOH solution containing 0.4 ppm of copper, an accumulation potential of -0.30 V, a scan rate of 100 mV s(-1) and a linear scan mode. There is a linear response to adenine concentration in the range of 0.1-1.0 ppb and the detection limit for 6 min accumulation time was of 4.0 ppt (3.0x10(-11) M). Proper conditions for measuring the adenine in presence of guanine, thymine and cytosine were also investigated. The method was applied for the determination of adenine in a sample of single-stranded calf thymus DNA.     

Separation of antimony(III) with iodide and dithizone by sorption on polyurethane foam from sulphuric acid medium for its spectrophotometric determination in glasses

A method for quantitative separation of antimony(III) by sorption on polyether based polyurethane foam and its spectrophotometric determination has been described. The method involves formation of a pink-red complex of antimony(III) with iodide (0.045M) and dithizone (2.3 x 10(-5)M) in 0.25-0.75M H(2)SO(4) medium, sorption of the complex on polyurethane foam (within 45 min) at room temperature followed by its elution with acidified acetone (acetone containing 0.008% H(2)SO(4)) and spectrophotometric measurement at 507.2 nm ( = 2.56 x 10(4) l mol cm). The method obeys Beer's law from 0.1 to 6.0 mug antimony(III). Tolerance limits of other ions are Co (100 mug), Ni (100 mug), Fe (10 mug), Cu (0.5 mug), Sn (20 mug), Zn (100 mug), As (100 mug), Mn (200 mug), Pb (50 mug), Ti (100 mug), V (50 mug), etc. Interference by iron and copper have been eliminated by treating with KOH prior to the extraction of antimony. The method has been standardized with glass samples spiked with known amounts of antimony and applied to the determination of antimony in various glasses.     

Determination of gallium by square-wave voltammetry anodic stripping, based on the electrocatalytic action of 2,2'-bipyridine in dimethylsulphoxide: comparison with an aqueous NaSCN/NaClO(4) electrolyte

Deposition potential, deposition time, square-wave frequency, 2,2'-bipyridine concentration, and gallium concentration have been studied in detail, for the determination of trace concentration levels of the metal by square-wave voltammetry anodic stripping analysis, in dimethylsulphoxide. Optimum conditions have been found for gallium(III) determination and results compared to those obtained in 0.5M NaSCN + 4.2M NaClO(4) aqueous electrolyte by obtaining calibration graphs for the range 1 x 10(-8)M-1 x 10(-5)M gallium. Accuracy (+/- 3%) and precision (4-6% SD) of this method were assessed with both 4 x 10(-8)M and 4 x 10(-7)M gallium solutions used as synthetic samples. The efficiency of solvent extraction of gallium with di-isopropyl ether was found to be 99.98% at a 4 x 10(-7)M gallium concentration. The proposed method was applied to the determination of the gallium content in rock mineral samples (using the above mentioned solvent extraction procedure), are compared to those obtained with the NaSCNNaClO(4) based electrolyte. No statistically significant difference was observed. Analytical procedures followed are given in detail.