Sequential optimization of a flow injection spectrophotometric method for the assay of chlorpromazine in pharmaceutical preparations

A new simple flow injection spectrophotometric method for the assay of chlorpromazine using cerium(IV) in sulfuric acid media was developed. The oxidized form of the drug was monitored at the maximum absorbance of 526 nm. The optimum conditions were 0.035M sulfuric acid, 3.80 x 10(-3)M cerium(IV), flow rate 4.85 ml/min, coil length 45 cm and sample size 110 mm(3). Optimization was carried out by the modified simplex method. Response surface methodology was employed to investigate the ruggedness of the method. A sampling frequency of 120 hr(-1) was attained. Relative standard deviations for standard sample were usually less than 0.75. The method was applied to the determination of chlorpromazine in proprietary drugs and results were statistically compared with the official British Pharmacopoeia (BP) method.     

Spectrophotometric determination of paracetamol in drug formulations by oxidation with potassium dichromate

A rapid spectrophotometric method for determination of paracetamol is described, based on oxidation with dichromate for 15 min in 6M sulphuric acid at 80 degrees , and measurement (at 580 nm) of the chromium(III) formed. The method is applied to the determination of paracetamol in drugs prescribed for colds, coughs and flu. Of the common pharmaceuticals associated with paracetamol, only ascorbic acid and acetylsalicylic acid interfere. The results have been statistically compared with those obtained by the official (BP) and cerium(IV) methods.     

New spectrophotometric and spectrofluorimetric methods for the determination of angiotensin II receptor antagonists in tablets and plasma

Spectrophotometric and spectrofluorimetric methods for the determination of five Angiotensin II type 1 receptor antagonists in tablets and plasma have been developed and optimized. The spectrophotometric method involves the addition of a measured excess of bromate-bromide in HCl medium and subsequent estimation of the residual bromine by reacting with a fixed amount of methyl orange. The spectrofluorimetric method depends on the oxidation of the drugs with cerium(IV) and subsequent monitoring of the fluorescence of the induced cerium(III) at 365 nm with excitation at 255 nm. Both of the proposed methods were successfully applied to the determination of the investigated drugs in their pure forms and pharmaceutical preparations. Besides, the spectrofluorimetric method was applied to the determination of irbesartan and telmisartan in biological fluids with good accuracy and precision.     

Computer assisted optimization of a flow-injection method for the assay of promethazine, chlorpromazine and trimeprazine in drug formulations

A simple, accurate and fast method for the determination of promethazine, chlorpromazine and trimeprazine neuroleptics in drug formulations by flow injection spectrophotometric detection was developed. The method was based on the oxidation of the drug with potassium dichromate in sulphuric acid media. Optimum conditions were obtained by using the modified simplex computer programme. A 110-mul sample volume was taken as reasonable for all the compounds. The optimum conditions reached were 76-cm coil length, 6.00 ml/min flow rate, 3.10M sulphuric acid and 0.00167M dichromate for promethazine; 94-cm coil length, 5.00 ml/min flow rate, 1.48M sulphuric acid and 0.00185M dichromate for chlorpromethazine and 80-cm coil length, 6.00 ml/min flow rate, 3.44M sulphuric acid and 0.000500M dichromate for trimeprazine. High sample throughput of at least 200 samples per hour was obtained for all compounds. Acceptable relative standard deviations in the range +/-0.4-0.9%, and good accuracy in the range 99.5-99.9% were attained when the method was statistically compared with the BP method and when applied to proprietary drugs, without suffering interferences.     

Indirect determination of uranium by the on-line reduction and fluorimetric detection of cerium(III).

A novel flow injection method has been developed for the indirect determination of uranium by the on-line reduction and subsequent fluorimetric detection of cerium(III). A sample solution containing uranium(VI), prepared as a sulfuric acid solution, was injected into a sulfuric acid carrier solution and passed through a column packed with metal bismuth to reduce uranium(VI) to uranium(IV). The sample solution was merged with a cerium(IV) solution to oxidize uranium(IV) to uranium(VI) and the cerium(III) generated was then monitored fluorimetricaly. The present method is free from interference from zirconium, lanthanides, and thorium, and has been successfully applied to the determination of uranium in monazite coupled with an anion-exchange separation in a sulfuric acid medium to eliminate iron(III). The sample throughput was 25 per hour and the lowest detectable concentration was 0.0042 mg l(-1).     

Kinetics and Mechanism of the Oxidation of Some Aldoses by Cerium(IV)

Abstract

The kinetics of oxidation of some aldoses by cerium(IV) have been studied spectrophotometrically in sulphuric acid medium. The reactions are second order; first order with respect to both cerium(IV) and aldose concentration. The reaction rate decreases with increase in sulphuric acid concentration. The mechanisms for the reactions are discussed.     

Sequential injection technique for automated titration: spectrophotometric assay of vitamin C in pharmaceutical products using cerium(IV) in sulfuric acid

For the first time sequential injection analysis (SIA) technique has been employed for titrimetry. A new SI titrimetric spectrophotometric method for the assay of vitamin C in drug formulations was explored. The method is based on the oxidation reaction of vitamin C with cerium(IV) in sulfuric acid media using a spectrophotometer as a detector with the wavelength monitored at 410 nm. A 2(3) factorial design chemometric approach was employed to study the interaction effect of the chemical and system variables, mainly cerium(IV), sulfuric acid concentrations and the flow rate. The results of the chemometric optimization revealed that the optimum operating conditions for the SI titrimetric analysis of vitamin C were 7.0 x 10(-3) M cerium(IV), 0.455 M sulfuric acid and 28.9 microL s-1 flow rate. A linear calibration plot for the determination of vitamin C was obtained in the concentration range between 30 to 200 ppm. The method was applied to the determination of vitamin C in pharmaceutical preparations and no excipient was found to pose any interference, thus rendering the method suitable for the determination of the drug in pharmaceutical preparations. The SIA method is found to be accurate when the results were statistically compared with the results obtained by the BP standard method. The SIA method is superior when compared to the conventional titration method, the BP standard method and previous methods with respect to precision and automation in solution handling.     

Amperometric ascorbimetric determination of cerium(IV) and Iron(III) with two polarized electrodes

Summary Amperometric ascorbimetric determinations of cerium(IV) and ferric iron have been carried out at 50°C with two polarized electrodes at 200 and 100 mV respectively. The results obtained are fairly accurate and precise within ±1.0 per cent. A simple method for successive determination of cerium and iron has been developed; and conditions for such estimations have been established. At an acidity of 2.5 M with respect to sulphuric acid, it is possible to ward off the reduction of ferric iron and thereby cerium(IV) is successfully titrated with ascorbic acid in this medium. After completion of the reaction and then lowering the acid concentration to p_H 1.5 with aid of ammonium hydroxide, Fe^III is titrated with standard ascorbic acid yielding good results.     

Flow injection titrimetric analysis of vitamin C in pharmaceutical products

A flow injection titrimetric method for the assay of vitamin C using cerium(IV) was developed. A 157 mul vitamin C solution was injected into a carrier stream of 7.48 x 10(-3)M cerium(IV) prepared in 0.10M sulfuric acid flowing at a rate of 5.0 ml/min. A 1.3 ml mixing chamber was employed for dispersion of the resultant solution which was propelled through a flow-through cell and detected using the spectrophotometer at a wavelength monitored at 410 nm. The method was applied to the determination of vitamin C in pharmaceutical preparations and a high accuracy was attained when compared with the British Pharmacoepeia (BP) method. Excellent precision indicated by a relative standard deviation of less than 0.9% was always obtained. No interferences were encountered and as many as 36 samples per hour were reached for throughput.     

Spectrofluorimetric Determination of the Hypertensive Drug Captopril Based on Its Oxidation with Cerium(IV)

A highly sensitive and specific spectrofluorimetric method for the analysis of captopril (CAP) in the pure form and in the tablet dosage forms has been described. The method was based on the oxidation of captopril by cerium(IV) in the presence of sulphuric acid and subsequent monitoring the fluorescence of the induced Ce(III) ion produced at λ_ex = 256 nm and λ_em = 354 nm. All variables affecting the reaction conditions such as cerium(IV) concentration, type and concentration of acid medium, reaction time, diluting solvents, temperature and heating time were carefully studied and optimized. Under the experimental conditions used, an excellent linear relationship was obtained between fluorescence intensity and the concentration of CAP. A linear range of determination was verified for captopril concentrations between 0.1–1.3 μg mL^?1 and the correlation coefficient of determination was 0.9997. Quantitation and detection limits were calculated. The precision of the method was satisfactory; the values of relative standard deviations did not exceed 1.14%. No interference could be observed from the excipients and additives are commonly presented in dosage forms. The proposed method was applied successfully for the assay of the studied drug in pure form and in pharmaceutical dosage forms. Recovery experiments revealed recovery of 99.82–100.21%. The results of the analysis show a good agreement with those obtained by official method stated in the United State Pharmacopoeia.     

Mechanistic study of cerium(IV) oxidation of antimony(III) in aqueous sulphuric acid in the presence of micro amounts of manganese(II) by stopped flow technique

The oxidation of antimony(III) by cerium(IV) has been studied spectrometrically (stopped flow technique) in aqueous sulphuric acid medium. A minute amount of manganese(II) (10⁻⁵ mol dm⁻³) is sufficient to enhance the slow reaction between antimony(III) and cerium(IV). The stoichiometry is 1:2, i.e. one mole of antimony(III) requires two moles of cerium(IV). The reaction is first order in both cerium(IV) and manganese(II) concentrations. The order with respect to antimony(III) concentration is less than unity (ca 0.3). Increase in sulphuric acid concentration decreases the reaction rate. The added sulphate and bisulphate decreases the rate of reaction. The added products cerium(III) and antimony(V) did not have any significant effect on the reaction rate. The active species of oxidant, substrate and catalyst are Ce(SO₄)₂, [Sb(OH)(HSO₄)]⁺ and [Mn(H₂O)₄]²⁺, respectively. The activation parameters were determined with respect to the slow step. Possible mechanisms are proposed and reaction constants involved have been determined.     

Spectrophotometric determination of H(2)-receptor antagonists via their oxidation with cerium(IV)

A simple, accurate and sensitive spectrophotometric method has been developed and validated for determination of H(2)-receptor antagonists: cimetidine, famotidine, nizatidine and ranitidine hydrochloride. The method was based on the oxidation of these drugs with cerium(IV) in presence of perchloric acid and subsequent measurement of the excess Ce(IV) by its reaction with p-dimethylaminobenzaldehyde to give a red colored product (lambda(max) at 464nm). The decrease in the absorption intensity of the colored product (DeltaA), due to the presence of the drug was correlated with its concentration in the sample solution. Different variables affecting the reaction were carefully studied and optimized. Under the optimum conditions, linear relationships with good correlation coefficients (0.9990-0.9994) were found between DeltaA values and the concentrations of the drugs in a concentration range of 1-20microgml(-1). The assay limits of detection and quantitation were 0.18-0.60 and 0.54-1.53microgml(-1), respectively. The method was validated, in terms of accuracy, precision, ruggedness and robustness; the results were satisfactory. The proposed method was successfully applied to the determination of the investigated drugs in pure and pharmaceutical dosage forms (recovery was 98.3-102.6+/-0.57-1.90%) without interference from the common excipients. The results obtained by the proposed method were comparable with those obtained by the official methods.     

Cerium (IV)-based chemiluminescence analysis of hydrochlorothiazide

A flow-injection analytical method for the determination of hydrochlorothiazide is presented. The method is based on the chemiluminescence reaction of hydrochlorothiazide with cerium(IV) in sulphuric acid, sensitized by the fluorescent dye rhodamine 6G. The proposed procedure allows quantitation of hydrochlorothiazide in the concentration range of 0.33-130 mumol l(-1) with a detection limit of 0.15 mumol l(-1), an RSD of 2.4% at 10 mumol l(-1) and a sample measurement frequency of 200 h(-1). The method was successfully applied to the determination of hydrochlorothiazide in pharmaceutical preparations containing, amongst others, lactose, maize starch, calcium phosphate, magnesium stearate, potassium chloride and E 110 (disodium-6-hydroxy-5-(4-sulphonatophenylazo) naphthalene-2-sulphonate) as the concomitant species. Apart from the single formulation, hydrochlorothiazide was also determined in tablets combined with the antihypertensive lisinopril.     

Determination of oxygen to uranium ratio in irradiated uranium dioxide by controlled potential coulometry

This work reports the determination of oxygen to uranium (O/U) ratio in irradiated UO_2+x fuel pellet of burnup of ca. 34 GWd/t by controlled potential coulometry. The method is based on the dissolution of the nuclear fuel in strong phosphoric acid (SPA) at 180–190 °C under an inert atmosphere. After dissolution, 8% sulphuric acid is added in order to obtain a 20% SPA in 8% sulphuric acid. A controlled potential coulometric determination of uranium(VI) is carried out at ?0.60V vs. ferri-ferrocyanide. The uranium(IV) contained in an aliquot of the fuel solution is oxidised to uranium(VI) with cerium(IV) sulphate, and the total uranium content is then determined by coulometry. Optimum experimental conditions have been established using simulated irradiated fuel solution containing various fission products which include cerium, tellurium, palladium, ruthenium, molybdenum and zirconium. Interference of the fission products and the possible removal of their interferences by preelectrolysis at +0.5 V vs. saturated calomel electrode (SCE) have been investigated. The accuracy of the coulometric method is confimed by polarographic measurement using several unirradiated UO_2+x fuel of known stoichiometry.     

Chemometric optimization of a SIA promethazine hydrochloride assay method

A sequential injection analysis (SIA) method for the assay of promethazine hydrochloride, based on its oxidation by acidified cerium(IV), was optimized. Three chemometric approaches were applied: (i) factorial design (3³ applied to surface plot and 2³ applied to effect factor) for screening the potential interacting variables, (ii) univariant for optimizing insignificantly interacting variables and (iii) simplex for optimizing potentially interacting variables. The optimum experimental conditions were 30 μl of 0.38 mol/l sulphuric acid, 30 μl of 3.99 × 10^− 3 mol/l cerium(IV), 20 μl of promethazine hydrochloride and 20 μl/s flow rate. The detection limit was 7.032 × 10^− 5 mol/l and the calibration curve was linear up to 1.563 mol/l with a correlation coefficient 0.9998, accuracy range of 89.0-101.5%, relative standard deviation 1.1% (n = 10) and sample frequency at least 20 samples/h. The method was applied to tablet form and validated with the British Pharmacopoeia method. The developed SIA method is fully automated, reproducible, sensitive, rapid and reagent-saving, and therefore suitable for routine control in tablets form.     

Fluorometric determination of diphenhydramine by flow-injection analysis

A sensitive, rapid and simple flow injection procedure for the determination of diphenhydramine has been designed based on a fluorometric approach. An aqueous solution of diphenhydramine is injected into a carrierreagent stream containing Ce(IV) in dilute sulphuric acid and the fluorescence intensity of the Ce(III) produced is monitored. Chemical, FIA and instrumental variables were optimized. Analytical features of the method are: linear range 0.2–2 ppm, precision 0.7%, sample throughput 80/h. The influence of some foreign substances which can be found in typical pharmaceutical samples containing diphenhydramine was also investigated. The diphenhydramine content of a pharmaceutical preparation was determined.     

Manganese(II) catalysed oxidation of glycerol by cerium(IV) in aqueous sulphuric acid medium: a kinetic and mechanistic study

The manganese(II) catalysed oxidation of glycerol by cerium(IV) in aqueous sulphuric acid has been studied spectrophotometrically at 25 °C and I = 1.60 mol dm⁻³. Stoichiometry analysis shows that one mole of glycerol reacts with two moles of cerium(IV) to give cerium(III) and glycolic aldehyde. The reaction is first order in both cerium(IV) and manganese(II), and the order with respect to glycerol concentration varies from first to zero order as the glycerol concentration increases. Increase in sulphuric acid concentration, added sulphate and bisulphate all decrease the rate. Added cerium(III) retards the rate of reaction, whereas glycolic aldehyde had no effect. The active species of oxidant and catalyst are Ce(SO₄)₂ and [Mn(H₂O)₄]²⁺. A mechanism is proposed, and the reaction constants and activation parameters have been determined.     

Determination of cerium in minerals with sulphanilic acid

Cerium can be determined colorimetrically in minerals with sulphanilic acid. Cerium(III) ions are oxidized with silver(II) in 1-7% sulphuric acid. Sulphanilic acid is oxidized by cerium(IV) ions in 20% sulphuric acid. The absorbance is determined at 540 nm. In the presence of maganese or chromium, cerium can be separated by precipitation as the oxalate. Lanthanum can be used as a gathering agent if necessary.     

离子排斥色谱法测定生脉注射液中的有机酸

1引言生脉注射液是由红参、麦冬和五味子3种药材经提取后制成的灭菌水溶液,为国家中药保护品种,具有益气养阴,复脉固脱的功效。前期的分析实验表明,生脉注射液中含有有机酸类成分。根据生脉注射液的生产工艺和3种药材的的化学成分研究报道,分析生脉注射液中的有机酸主要来源于五味子。五味子含有柠檬酸、苹果酸、琥珀酸等多种有机酸成分。目前,有机酸的分析方法有气相色谱法[1]、高效液相色谱法[2]、毛细管电泳法[3]及离子色谱法[4]。这些方法专属[5]