Determination of selenium in fish flesh by hydride generation atomic absorption spectrometry

Selenium was determined in freeze-dried fish flesh from perch, pike-perch and the fish flesh reference materials MA-A-2 No. 1174 and MA-B-3 No. 151 (both from the International Atomic Energy Agency) by hydride generation atomic absorption spectrometry. Four different decomposition procedures were tested. They yielded consistent results for the four specimens, but the certified concentration level of selenium in the reference material MA-A-2 was not reached. This indicated losses or the presence of very stable selenium-containing compounds in this fish flesh. Neutron activation analysis of the reference material, however, was in agreement with those results obtained.     

Evaluation of high-pressure microwave digestion methods for hydride generation atomic absorption spectrometric determination of total selenium and arsenic in sediment

Five closed-vessel microwave digestion methods were compared for the accurate determination of arsenic and selenium in NIST SRM 1645 River Sediment by flow-injection hydride-generation atomic absorption spectrometric methods. The digestion methods using five different acid mixtures (HNO₃/ H₂SO₄, HNO₃/HCl0₄, HNO₃/HCl, HNO₃/HCl/HF, HNO₃/H₂SO₄/HClO₄) were all found to be reliable for the determination of the analytes. Taking into consideration the safety and suitability for the analysis of other metals, the methods based on the use ofaqua regia are recommended for closed vessel microwave digestion with pressure control. Using the quick digestion program, the presence of up to 10% organic content in soil samples did not adversely affect the closed vessel digestion and did not cause the loss of volatile analytes. After digestion, opening the vessel under an inner pressure of below 345 kPa (50 psi) had no effect on the accuracy of the results. The recommended digestion methods (HNO₃/HCl and HNO₃/ HCl/HF) for the reliable determination of arsenic and selenium in different sediment samples were demonstrated. The calculated detection limits (3 _b ) were less than 0.030 g/g and 0.033 g/g for arsenic and selenium, respectively. All analytical results for arsenic and selenium in SRM 1645 River sediment, NRCC BCSS-1 Marine Sediment and NIES CRM Pond Sediment were within or near the certified and reported ranges, with the exception of selenium in NIES CRM No. 2 Pond Sediment.     

Comparison of four digestion methods for the determination of selenium in bovine liver by hydride generation and atomic-absorption spectrometry in a flow system

A flow system for hydride generation and atomic-absorption spectrometry is described, and the results from the optimization of the equipment for selenium determination are reported. For a sample volume of 0.6 ml the limit of detection for selenium was 0.1 mug l . and the imprecision less than 1% RSD at the 10-mug l . level. Four digestion procedures for selenium in bovine liver have been tested. All procedures gave concordant results, provided that the standard-additions method was used. The accuracies of the overall analytical procedures were estimated by comparison with results from neutron-activation analysis and analysis of NBS Bovine Liver, No. 1577. These comparisons proved that the accuracies of the procedures described in this paper are good.     

Determination of serum selenium by hydride generation flame atomic absorption spectrometry

Serum is rapidly digested with a mixture of nitric and perchloric acids at a temperature of 180 +/- 10 degrees C, and hydrochloric acid is used to reduce selenium(VI) to selenium(IV). Selenium is determined by hydride generation flame atomic absorption spectrometry. The results show that this method has the advantages of being sensitive, accurate, rapid and simple. After the serum is digested and diluted, 4.0 ml is taken for the determination. The characteristic concentration, detection limit, variation coefficient, recovery rate and linear range are 2.93 mug 1(-1), 1.55 mug l(-1), 1.6-5.0%, 97.3-99.2% and 0.0-320.0 mug l(-1) respectively. Serum at 4 degrees C and in frozen state can be preserved for at least 7 and 14 days, respectively.     

Comparison of wet microwave digestion methods of plant materials for the determination of metals by flame atomic absorption spectrometry

Microwave closed-system wet digestion procedures for plant samples were examined. Each procedure was tested with samples of tobacco and cabbage, and included digestion by the use of different acids composition, almost complete evaporation of the digest, and then dissolution of the residue in 1% nitric acid. Three microwave digestion programs that varied power, duration, and temperature were used. Closed-vessel reactions followed open-vessel reaction-delay time. Using flame atomic absorption spectrometry on the digests, four or five elements were determined to evaluate effectiveness, precision and accuracy of analytes extraction into solution. After a preliminary study of tobacco digests, the four most effective procedures were chosen, and detailed investigations were carried out on both tobacco and cabbage reference materials. Although all four of the final procedures were accurate, the most precise procedure, with the lowest errors of determination, was using reverse ‘aqua regia’ for tobacco and ‘aqua regia’ for cabbage.     

Electrochemical hydride generation atomic absorption spectrometry for determination of cadmium

An electrolytic hydride generation system for determination of another hydride forming element, cadmium, by catholyte variation electrochemical hydride generation (EcHG) atomic absorption spectrometry is described. A laboratory-made electrolytic cell with lead-tin alloy as cathode material is designed as electrolytic generator of molecular hydride. The influences of several parameters on the analytical signal have been evaluated using a Plackett-Burman experimental design. The significant parameters such as cathode surface area, electrolytic current, carrier gas flow rate and catholyte concentration have been optimized using univariate method. The analytical figures of merit of procedure developed were determined. The calibration curve was linear up to 20 ng ml⁻¹of cadmium. The concentration detection limit (3σ, n = 8) of 0.2 ng ml⁻¹ and repeatability (relative standard deviation, n = 7) of 3.1% were achieved at 10.0 ng ml⁻¹. It was shown that interferences from major constituents at high concentrations were significant. The accuracy of method was verified using a real sample (spiked tap water) by standard addition calibration technique. Recovery of 104% was achieved for Cd in the spiked tap water sample.     

Determination of selenium in water and soil by hydride generation atomic absorption spectrometry using solid reagents

A hydride generation method for the determination of traces of selenium at ng mL⁻¹ concentration ranges has been introduced using a solid mixture of tartaric acid and sodium tetrahydroborate. Atomic absorption spectrometry (AAS) has been used as the detection system. Several parameters such as the ratio of tartaric acid to sodium tetrahydroborate, type and amount of acid, and the reaction temperature were optimized by using 640 ng mL⁻¹ (16 ng per 25 μL) of Se(IV) standard solution. The calibration curve was linear from 20 to 1200 ng mL⁻¹ (0.5-30 ng Se(IV) per 25 μL). The relative standard deviation (%R.S.D.) of the determination was 1.93% and the detection limit was 10.6 ng mL⁻¹ (265 pg per 25 μL) of Se(IV). The reliability of the method was checked using different types of environmental samples, such as several types of water, a sample of soil and also in a kind of calcium phosphate sample by standard addition method. For conversion of Se(VI) present in real samples to Se(IV), l-cysteine was added to NaBH₄ and tartaric acid mixture. The results showed good agreement between this method and other hydride generation techniques.     

Optimization of the determination of selenium in marine samples by atomic absorption spectrometry: Comparison of a flameless graphite furnace atomic absorption system with a hydride generation atomic absorption system

A comparison has been made between a graphite furnace system based on nickel as a matrix stabilizing metal and an automated hydride generation system with a heated quartz cell. The effect of nickel as a matrix modifier was studied in pure selenite solutions as well as in biological matrixes by different charring temperatures. The suppression effect of different acids on the response of the analyte is reported and discussed. The use of an electrically heated quartz tube as an alternative to the argon hydrogen flame method unproved the selenium determination by hydride generation atomic absorption. The effect of hydrochloric acid to secure quantitative formation of selenium (IV) and the interference of copper in the response measurements have been studied. Further a comparison has been made between three different digestion procedures when the hydride generation atomic absorption system was applied. The results of the graphite furnace atomic absorption and the hydride generation atomic absorption were found to be equally accurate, but the graphite furnace technique gave better reproducibility.     

Method development and optimization for the determination of selenium in bean and soil samples using hydride generation electrothermal atomic absorption spectrometry

The present investigation is the first part of an initiative to prepare a regional map of the natural abundance of selenium in various areas of Brazil, based on the analysis of bean and soil samples. Continuous-flow hydride generation electrothermal atomic absorption spectrometry (HG-ET AAS) with in situ trapping on an iridium-coated graphite tube has been chosen because of the high sensitivity and relative simplicity. The microwave-assisted acid digestion for bean and soil samples was tested for complete recovery of inorganic and organic selenium compounds (selenomethionine). The reduction of Se(VI) to Se(IV) was optimized in order to guarantee that there is no back-oxidation, which is of importance when digested samples are not analyzed immediately after the reduction step. The limits of detection and quantification of the method were 30 ng L⁻¹ Se and 101 ng L⁻¹ Se, respectively, corresponding to about 3 ng g⁻¹ and 10 ng g⁻¹, respectively, in the solid samples, considering a typical dilution factor of 100 for the digestion process. The results obtained for two certified food reference materials (CRM), soybean and rice, and for a soil and sediment CRM confirmed the validity of the investigated method. The selenium content found in a number of selected bean samples varied between 5.5 ± 0.4 ng g⁻¹ and 1726 ± 55 ng g⁻¹, and that in soil samples varied between 113 ± 6.5 ng g⁻¹ and 1692 ± 21 ng g⁻¹.     

A simple and sensitive continuous hydride generation system for the determination of arsenic and selenium by atomic absorption and atomic fluorescence spectrometry

The development and optimization of a continuous hydride generation system for atomic absorption spectrometry (a.a.s.) and atomic fluorescence spectrometry (a.f.s.) is described. Sodium tetrahydroborate(III) solution and sample solution are delivered by two small peristaltic pumps to a gas/liquid separator. The evolved hydrides are swept to a miniature argon/hydrogen diffusion flame burning on a borosilicate glass tube. Detection limits (2σ) obtained for arsenic are 0.8 ng ml^-1 by a.a.s. and 0.34 ng ml^-1 by a.f.s., and for selenium 0.5 ng ml^-1 by a.a.s. and 0.13 ng ml^-1 by a.f.s. Linear working ranges are typically 1–100 ng ml^-1 with a typical measurement time of 1 min per sample or standard.     

Ultratrace determination of tin by hydride generation in-atomizer trapping atomic absorption spectrometry

A quartz multiatomizer with its inlet arm modified to serve as a trap (trap-and-atomizer device) was employed to trap tin hydride and subsequently to volatilize collected analyte species with atomic absorption spectrometric detection. Generation, atomization and preconcentration conditions were optimized and analytical figures of merit of both on-line atomization as well as preconcentration modes were quantified. Preconcentration efficiency of 95 ± 5% was found. The detection limits reached were 0.029 and 0.14 ng mL⁻¹ Sn, respectively, for 120 s preconcentration period and on-line atomization mode without any preconcentration. The interference extent of other hydride forming elements (As, Se, Sb and Bi) on tin determination was found negligible in both modes of operation. The applicability of the developed preconcentration method was verified by Sn determination in a certified reference material as well as by analysis of real samples.     

Study of some interfering processes in the arsenic, antimony and selenium determination by hydride generation atomic absorption spectrometry

Summary A detailed study of interfering processes in the determination of As, Sb and Se using a twin-channel hydride generation flow-system is presented. The influence of As, Sb, Se and Sn on all three studied elements has a similar character and occurs in the gas phase only. In the presence of bismuth and tellurium interferences occur also in the liquid phase. It was found that arsenic and antimony may influence the analytical signals of elements with analytical lines in the range from 190 to 235 nm by non-specific absorption due to molecular band spectra.Dedicated to Professor Dr. Wilhelm Fresenius on the occasion of his 80th birthday     

Determination of selenium in sediments by hydride generation atomic absorption spectrometry. Elimination of interferences

Summary The hydride generation/atomic absorption spectrometry (AAS) with an automated flow system is useful for the routine analysis of selenium in environmental samples. This method is, however, subject to interferences from transition metal ions and other hydride forming ions. The conditions to minimize the interferences were established: the concentration of hydrochloric acid 6 mol/l; the concentration of tetrahydroborate 0.5%. Iron(III) chloride released the depression of selenium signals by metal ions such as copper(II) and bismuth(III). Selenium in several standard reference materials including sediment samples was determined by the present method and by fluorimetry with 2,3-diaminonaphthalene. The results obtained by the two methods agreed with an acceptable precision. This means that hydride generation/AAS offers good precision and accuracy in the determination of selenium in sediment samples as well as DAN fluorimetry. However, the former is much simpler in operation. The method was applied to the determination of selenium in estuarine sediments collected in Nagoya harbor and Ise Bay. The results can be used to assess the pollution state of these places.

---

Selenbestimmung in Sedimenten durch AAS mit Hydriderzeugung. Eliminierung von Störungen

     

Comparison of pre-reducing agents for antimony determination by hydride generation atomic fluorescence spectrometry

A systematic study of antimony reduction prior to its determination by hydride generation atomic fluorescence spectrometry (HG-AFS) was carried out. The efficiency of l-cysteine, potassium iodide and potassium iodide/ascorbic acid was studied for this purpose. The hydride generation step was optimised in the presence of those pre-reductors. From the results, l-cysteine was found to be the most suitable pre-reducing agent. Methodology was validated, obtaining detection limits lower than 90 ng l⁻¹ and repeatability and reproducibility better than 3% R.S.D. and 5% R.S.D., respectively, in all cases. In order to evaluate the methodology developed and the influence of the matrix, recovery from waters from different sources was tested by HG-AFS and also by inductively coupled plasma mass spectrometry (ICP-MS). Accuracy was assessed by analysing three water reference materials at different antimony concentration levels. The high sensitivity of the developed methodology enables it to be applied for monitoring drinking waters according to the maximum admissible concentration of antimony established by the EU Directives.     

On-line hyphenation of hydride generation with in situ trapping flame atomic absorption spectrometry for arsenic and selenium determination.

The analytical performances of coupled hydride generation, integrated atom trap (HG-IAT) atomizer flame atomic absorption spectrometry (FAAS) systems were evaluated for determination of As and Se in biological and environmental reference materials. Arsenic and Se hydrides are atomized in air-acetylene flame-heated IAT. A new design of HG-IAT-FAAS hyphenated technique that would exceed the operational capabilities of existing arrangements (a water-cooled single silica tube, double-slotted quartz tube or an "integrated trap") was investigated. A dramatic improvement in detection limit was achieved compared with that obtained using anyone of the above atom trapping techniques separately. The concentration detection limits were 4 and 3 ng ml(-1) for As and Se, respectively. For a 2 min in situ preconcentration time, sensitivity enhancement, compared to FAAS, were 875 and 833 folds for As and Se, respectively, using hydride generation, atom trapping technique. The sensitivity can be further improved by increasing the collection time. The relative standard deviations (RSDs) are of the order of 5 - 9% for this hyphenated technique. The designs studied include slotted tube, water-cooled single silica tube and integrated atom trap. The accuracy was assessed by analyses of NRCC DOLT-2 (Dogfish Liver) and NIST SRM 1648 (Urban Particulate Matter) reference materials. The measured As and Se contents in two reference materials were in satisfactory agreement with the certified values.     

Determination of selenium in vegetables by hydride generation atomic fluorescence spectrometry

A digestion mixture of H₂SO₄/HNO₃/H₂O₂/HF/V₂O₅ was investigated for decomposition of plant samples and sensitive detection of selenium was achieved by hydride generation atomic fluorescence spectrometry (HG-AFS). The method was found to be accurate and reproducible, with a low detection limit (DL) (0.14 ng g⁻¹ solution). The repeatability of the determination was mostly around 10%, the reproducibility over a period of 8 months for determination of selenium in the standard reference material Trace Elements in Spinach Leaves, NIST 1570a, was 9% and the relative measurement uncertainty was 7% using a coverage factor of 2.3 at 95% probability. The average recovery of the whole procedure was 90%. The characteristics of this method are simple and inexpensive equipment, low consumption of chemicals and the ability to analyse many samples in a short time. The whole procedure was carried out in the same PTFE tube, and in addition only a simple cleaning procedure is needed. As a consequence of all these advantages, the described method is suitable for environmental and nutritional studies. The selenium content was determined in 44 vegetable samples from different regions of Slovenia and the contents found were in the range 0.3-77 ng g⁻¹ wet weight.     

Determination of selenium using atomically imprinted polymer (AIP) and hydride generation atomic absorption spectrometry

This paper describes selenium determination based on Se⁰ preconcentration in the imprinted polymer (synthesized with 2.25 mmol SeO₂, 4-vinylpyridine and 1-vinylimidazole) with subsequent detection on-line in HG-FAAS. During the synthesis, SeO₂ is reduced to Se (0). Therefore, there are no MIP neither IIP in the present work, thus we denominated: AIP, i.e., atomically imprinted polymers. For the optimization of analytical parameters Doehlert design was used. The method presented limit of detection and limit of quantification of 53 and 177 ng L⁻¹, respectively, and linear range from 0.17 up to 6 μg L⁻¹ (r = 0.9936). The preconcentration factor (PF), consumptive index (CI) and concentration efficiency (CE) were 232; 0.06 mL and 58 min⁻¹ respectively. The proposed method was successfully applied to determine Se in Brazil nuts (0.33 ± 0.03 mg kg⁻¹), apricot (0.46 ± 0.02 mg kg⁻¹), white bean (0.47 ± 0.03 mg kg⁻¹), rice flour (0.47 ± 0.02 mg kg⁻¹) and milk powder (0.22 ± 0.01 mg kg⁻¹) samples. It was possible to do 12 analyzes per hour. Accuracy was checked and confirmed by analyzing certified reference material (DORM-2, dogfish muscle), and samples precision was satisfactory with RSD lower than 10%.     

Preconcentration and determination of tellurium in garlic samples by hydride generation atomic absorption spectrometry

A procedure for the determination of traces of total tellurium (Te) in garlic (Allium sativa) is described that combines hydride generation atomic absorption spectrometry with preconcentration of the analyte by coprecipitation. The samples, each spiked with lanthanum nitrate (20 mg/L), are introduced into an Amberlite XAD-4 resin and mixed with ammonium buffer (pH 9.1). Te is preconcentrated by coprecipitation with the generated lanthanum hydroxide precipitate. The precipitate is quantitatively collected in the resin, eluted with hydrochloric acid, and then transferred into the atomizer device. Considering a sample consumption of 25 mL, an enrichment factor of 10 was obtained. The detection limit (3sigma) was 0.03 microg/L, and the precision (relative standard deviation) was 3.5% (n = 10) at the 10 microg/L level. The calibration graph using the preconcentration system for Te was linear with a correlation coefficient of 0.9993. Satisfactory results were obtained for the analysis of Te in garlic samples.