Direct determination of beryllium, copper and zinc in AlU matrices by electrothermal atomization atomic-absorption spectrometry

An atomic-absorption spectrometric method with electrothermal mode of atomization has been developed for the direct determination of Be, Cu and Zn in AlU (3:1) matrix samples without prior chemical separation of the major matrix. The studies carried out include the effect of the matrix on the analyte absorbance, optimization of sample aliquot and other experimental parameters, and analysis of a number of synthetic samples. Nanogram amounts of the analytes can be determined with a solution aliquot of 5 microlitres containing 25 micrograms of the sample with a precision of 6% or better. The analytical range obtained for these analytes is Be: 2-20 mug/l., Cu: 20-200mug/l. and Zn: 1-40mug/ml in the AlU matrix. The analysis of synthetic samples has shown good agreement with their added contents.     

Determination of arsenic, cadmium, lead and selenium in highly mineralized waters by graphite-furnace atomic-absorption spectrometry

A graphite-furnace AAS method using the stabilized-temperature platform furnace (STPF) concept, mixed palladium and magnesium nitrates as chemical modifier and Zeeman background correction has been applied to the direct determination of As, Cd, Pb and Se in highly mineralized waters used for medicinal purposes. These contain 20-40 g/l. concentrations of salts, mainly sodium and magnesium chlorides, bicarbonates and sulphates. The use of a pre-atomization cool-down step to 20 degrees in the graphite-furnace programme reduced the background absorption. Increasing the mass of magnesium nitrate modifier to 5 times that originally proposed improved the analyte peak shape. Under these conditions, no interference was found in analysis of the chloride/bicarbonate type of water, but the sodium and magnesium sulphate type of water had to be diluted, and even then an interference remained. Calibration with matrix-free standard solutions was used, but use of spike recovery is strongly recommended for testing the accuracy. The limits of determination (4.65sigma) of the proposed method for undiluted samples are 2.0 mug/l. for As, 0.05 mug/l. for Cd, 1.0 mug/l. for Pb and 1.5 mug/l. for Se.     

Kinetic-spectrophotometric determination of trace amounts of As(III) based on its inhibitory effect on the redox reaction between bromate and hydrochloric acid

A simple, sensitive, rapid and reliable method has been developed for spectrophotometric determinations of As(III) in the presence of As(V) based on its inhibition effect on the redox reaction between bromate and hydrochloric acid. The decolorization of methyl orange by the reaction products was used to monitor the reaction spectrophotometrically at 525 nm. The method allows the determination of arsenic in the range of 6-1000 mug l(-1). The relative standard deviation for 10 determinations of 40 mug l(-1) of As(III) was 1.43% and the limit of detection, corresponding to a signal to noise ratio of three, was 3.4 mug l(-1). The proposed method was applied to the determination of As(III) in water samples with satisfactory results.     

Spectrophotometric detection of arsenic using flow-injection hydride generation following sorbent extraction preconcentration

An automated system with a C(18) bonded silica gel packed minicolumn is proposed for spectrophotometric detection of arsenic using flow-injection hydride generation following sorbent extraction preconcentration. Complexes formed between arsenic(III) and ammonium diethyl dithiophosphate (ADDP) are retained on a C(18) sorbent. The eluted As-DDP complexes are merged with a 1.5% (w/v) NaBH(4) and the resulting solution is thereafter injected into the hydride generator/gas-liquid separator. The arsine generated is carried out by a stream of N(2) and trapped in an alkaline iodine solution in which the analyte is determined by the arsenomolybdenum blue method. With preconcentration time of 120 s, calibration in the 5.00-50.0 mug As l(-1) range and sampling rate of about 20 samples h(-1) are achieved, corresponding to 36 mg ADDP plus 36 mg ammonium heptamolybdate plus 7 mg hydrazine sulfate plus 0.7 mg stannous chloride and about 7 ml sample consumed per determination. The detection limit is 0.06 mug l(-1) and the relative standard deviation (n=12) for a typical 17.0 mug As l(-1) sample is ca. 6%. The accuracy was checked for arsenic determination in plant materials from the NIST (1572 citrus leaves; 1573 tomato leaves) and the results were in agreement with the certified values at 95% confidence level. Good recoveries (94-104%) of spiked tap waters, sugars and synthetic mixtures of trivalent and pentavalent arsenic were also found.     

Electrothermal atomic absorption spectrometric determination of ultra-trace amounts of tin by in situ preconcentration in a graphite tube using flow injection hydride generation with on-line ion-exchange separation

A method was developed for the ultra-trace determination of tin by in situ preconcentration in a graphite tube using a flow injection hydride generation technique with on-line ion-exchange separation. The sample was prepared in 2M hydrochloric acid before being passed through an incorporated micro-column packed with a strongly basic anion-exchanger D-201. The tin was retained as its chlorostannate complex and subsequently eluted by de-ionized water into the hydride generation system. The hydride and hydrogen gases evolved were separated from the liquid phase in a gas-liquid separator and transferred into a palladium-coated graphite tube pre-heated to 300 degrees C to collect the analyte, which was later atomized at 2300 degrees C. With the reported system, tin was determined at a sampling frequency of 30/hr with a detection limit (3sigma) of 0.01 mug/l. using 10.7 ml sample. The precision was 1.5% RSD at the 0.5 mug/l. level. The proposed method was applied to the determination of tin in tap water, hair, serum samples and geological reference samples.     

Determination of trace chromium(VI) and molybdenum(VI) in natural and bottled mineral waters using long pathlength absorbance spectroscopy (LPAS)

A flow-through solid phase spectrophotometric (SPS) sensing device is proposed for the determination of minoxidil. The analyte is concentrated on Sephadex SP-C25 ion-exchanger packed in a flow cell and it is monitored by UV-Vis spectrophotometry at 282 nm, without derivatization reaction. When a HCl (10(-2) mol l(-1))/NaCl (5x10 (-2) mol l (-1)) solution is used as carrier/desorbing solution, the sensor responds linearly in the measuring range of 0.2-7, 0.1-4 and 0.05-2 mug ml(-1) with detection limits of 60, 33 and 6 ng ml(-1) for 600, 1000 and 2000 mul of sample, respectively. The relative standard deviations (%) for these volumes are 0.38, 1.06 and 2.63, respectively. The method was satisfactorily applied to the determination of minoxidil in pharmaceutical preparations and the results were compared with those obtained by high performance liquid chromatography (HPLC).     

Preconcentration of Cr(III), Co(II), Cu(II), Fe(III) and Pb(II) as calmagite chelates on cellulose nitrate membrane filter prior to their flame atomic absorption spectrometric determinations

A method for the preconcentration and determination of Cr(III), Co(II), Cu(II), Fe(III) and Pb(II) ions by atomic absorption spectrometry has been described. The method was based the collection of metal-calmagite complexes on a soluble cellulose nitrate membrane filter. The detection of the solution was obtained by flame atomic absorption spectrometry (FAAS) after completely dissolving the membrane with 0.5 ml of nitric acid at 80 degrees C. The metal ions were recovered quantitatively at pH 8. Various factors which affect the collection and determination of metal ions such as, type and size of the membrane filter, solvent for dissolution of the species retained on the filter were investigated. The detection limits were varying 0.06 mug l(-1) for Cu to 2.5 mug l(-1) for Cr. An application of the proposed method for analyte ions in mineral and tap water samples was also described with satisfactory results (recoveries >95%, relative standard deviations <10%).     

Minimization of lead and copper interferences on spectrophotometric determination of cadmium using electrolytic deposition and ion-exchange in multi-commutation flow system

A new strategy for minimization of Cu(2+) and Pb(2+) interferences on the spectrophotometric determination of Cd(2+) by the Malachite green (MG)-iodide reaction using electrolytic deposition of interfering species and solid phase extraction of Cd(2+) in flow system is proposed. The electrolytic cell comprises two coiled Pt electrodes concentrically assembled. When the sample solution is electrolyzed in a mixed solution containing 5% (v/v) HNO(3), 0.1% (v/v) H(2)SO(4) and 0.5 M NaCl, Cu(2+) is deposited as Cu on the cathode, Pb(2+) is deposited as PbO(2) on the anode while Cd(2+) is kept in solution. After electrolysis, the remaining solution passes through an AG1-X8 resin (chloride form) packed minicolumn in which Cd(2+) is extracted as CdCl(4)(2-). Electrolyte compositions, flow rates, timing, applied current, and electrolysis time was investigated. With 60 s electrolysis time, 0.25 A applied current, Pb(2+) and Cu(2+) levels up to 50 and 250 mg l(-1), respectively, can be tolerated without interference. For 90 s resin loading time, a linear relationship between absorbance and analyte concentration in the 5.00-50.0 mug Cd l(-1) range (r(2)=0.9996) is obtained. A throughput of 20 samples per h is achieved, corresponding to about 0.7 mg MG and 500 mg KI and 5 ml sample consumed per determination. The detection limit is 0.23 mug Cd l(-1). The accuracy was checked for cadmium determination in standard reference materials, vegetables and tap water. Results were in agreement with certified values of standard reference materials and with those obtained by graphite furnace atomic absorption spectrometry at 95% confidence level. The R.S.D. for plant digests and water containing 13.0 mug Cd l(-1) was 3.85% (n=12). The recoveries of analyte spikes added to the water and vegetable samples ranged from 94 to 104%.     

Determination of low levels of bromide in fresh water after chromatographic enrichment

A method has been developed for the determination of bromide in fresh water. The analyte is enriched on the anion-exehanger Dowex 1 x 8, which exhibits a considerably greater affinity for bromide than for the major anions in fresh water. Sodium perchlorate is used as eluent and an enrichment factor of ~100 can be achieved. The eluted bromide is oxidized with peroxodisulphate to bromate, which is determined iodometrically by a previously published spectrophotometric method. The enrichment in the presence of the major components of fresh water has been studied. Only bicarbonate has been found to interfere, but this interference can be avoided by acidifying the sample with hydrochloric acid. The recovery from synthetic fresh water with ionic concentrations corresponding to 0.005 equivalent/l. and spiked with bromide was 100% at bromide concentrations larger than 50 nM (4 mug l. ) and about 90% at 10 nM. The detection limit is 1.5nM and the limit of determination 5nM for 1-litre samples.     

Determination of trace hydrazine by differential pulse voltammetry using magnetic microspheres

A new type of magnetic polymer microspheres containing ketone groups on the surface was synthesized. It can be reacted with hydrazine to produce electroactive adduct. Reduction of this derivative that was aggregated on the magnetic electrode is possible and effective in indirect determination of hydrazine. The experimental conditions and electrode structure were discussed. Under optimum conditions, It was found that the peak potential (Ep) of hydrazine is -1.06 V (vs. Ag/AgCl). Hydrazine in the range 0.3-500 mug l(-1) can be determined. The detection limits for hydrazine is 0.1 mug l(-1). The relative standard deviation for determination of 100 mug l(-1) hydrazine was 2.43 %. The method was applied to the determination of hydrazine in water samples with satisfactory results.     

Malachite green as a reagent for detection and spectrophotometric determination of chromium(VI)

A sensitive and inexpensive method of spectrophotometric determination of chromium(VI), based on the absorbance of its complex with malachite green and acetic acid at pH 2.5 is reported. The complex shows a molar absorptivity of 8 x 10(4) l.mole(-1) cm(-1) at 560 nm, using malachite green and acetic acid as reference solution. The effect of time, temperature, pH and reagent concentration is studied and optimum operating conditions are established. Beer's law is applicable in the concentration range 2.0-22.8 mug/ml chromium(VI). The resin beads act as a catalyst and as little as 1.6 mug of chromium(VI) is detected in the resin phase as compared to 4.1 mug in the solution phase. The standard deviation in the determinations is +/-0.40 mug/ml for a 10.35 mug/ml solution.     

Flow system exploiting multicommutation to increase sample residence time for improved sensitivity. Simultaneous determination of ammonium and ortho-phosphate in natural water

A flow system for the simultaneous determination of ammonium and phosphate in river water at the mug ml(-1) level employing a low expensive LED-based photometer is described. The manifold of the flow system comprised four analytical pathways containg a set of three-way solenoid valves and an automatic injector commutator. The signal measurements of both analytes were carried out using two LED-based photometers attached to the flow cells. A microcomputer running a programme written in quickbasic 4.5 provided facilities to control the system and to carry out simultaneously two analytical procedures also performing data acquisition. For the determination of ortho-phosphate the method based on reaction with molybdate and ascorbic acid was employed, while for ammonium the method based on reaction with hypochlorite and salicylic acid was selected. The four-pathway structure of the manifold allowed the sample incubation time to be increased to 130 s to permit the reaction to occur without a decrease in sample throughput. The usefulness of the system was ascertained by analyzing a set of water samples. Applying the paired t-test to results obtained employing reference methods, no significant difference at the 95% confidence level was observed for both analytes. Other profitable features such as an analytical throughput of 112 analyte determination per hour; relative standard deviations of 1.1 and 0.7% (n=6) ammonium and phosphate, respectively, reagent consumption of 0.3 mg ammonium molybdate, 0.75 mg salicylic acid, 3.3 mg ascorbic acid and sodium hypochlorite per determination; detection limits of 7.0 mug l(-1) NH(4)(+) and 17.0 mug l(-1) PO(4)(3-) were also achieved.     

Determination of soluble chromium in simulated PWR coolant by differential-pulse adsorptive stripping voltammetry

An analytical method has been developed for the determination of dissolved chromium at concentrations less than 2 mug/l. in PWR coolant by differential-pulse adsorptive stripping voltammetry at a hanging mercury drop electrode. Concentrations above 2 mug/l. can be determined by appropriate dilution of the sample. The method is based on measurement of the current associated with reduction of a chromium(III)-DTPA (diethylenetriaminepenta-acetic acid) complex adsorbed at the surface of the mercury drop. The effects of boric acid, pH, DTPA concentration, accumulation potential and time were investigated together with the oxidation state of the chromium. No interference was observed from other transition metal ions expected to be present in PWR coolant. No alternative chemical technique of similar sensitivity was available for comparison with the results obtained in solutions containing <1 mug/l. chromium. Recoveries from simulated coolant solutions were greater than 95% and the relative standard deviations for single determinations were in the range 12-25%. The statistical limit of detection at the 95% confidence level was 0.023 mug/l. This method of analysis should prove valuable in corrosion studies and is uniquely capable of following the changes in soluble chromium concentration in PWR coolant that follow operational changes in the reactor.     

Mixed micellar medium for the spectrophotometric determination of molybdenum in molybdenum/tungsten mixtures

Effects of cetyltrimethylammonium bromide (CTAB) and/or nonylphenoxypolyethoxyethanol (OP) on the absorption spectra of the complexes of molybdenum and tungsten with bromopyrogallol red (BPR) were studied. Based on these effects, a mixture of CTAB and OP was thus selected as a medium for the selective and sensitive determination of Mo in Mo/W binary mixtures. Under the optimum conditions, Beer's law was obeyed over the range 0.06-0.8 mug ml(-1) Mo with molar absorptivity being 1.3x10(5) l mol(-1) cm(-1) and detection limit 0.025 mug ml(-1). For 1.0 mug Mo, at least 20 mug W did not interfere in the determination of Mo with average recovery and relative standard deviation being 99.5% and <2%, respectively. The method developed maintained the features of simplicity and rapidity and, moreover, its selectivity and sensitivity enhanced greatly due to the use of CTAB/OP mixed micellar medium. When coupled with a compatible concentration method, the proposed method could be used for the determination of trace Mo in natural waters.     

Preconcentration of trace amounts of manganese from natural waters by means of a macroreticular poly(dithiocarbamate) resin

A chelating poly(dithiocarbamate) resin (PDTC) with macroreticular support is characterized as effective collector for traces of manganese from natural waters. Using small PDTC columns preconcentration of manganese can be achieved even at high flow-rates (5-6 ml/min) and sample volumes (1500 ml). Accordingly, PDTC resin is used for the preconcentration of manganese from water samples prior to its determination by flame atomic-absorption spectrometry. A series of ions abundant in natural waters do not interfere. The sensitivity and detection limit were 2.5 and 0.5 mug/l., respectively. The relative standard deviations of the results for a manganese concentration of 40-400 mug/l. are in the range 1.1-6.2%. In mineral and tap waters analysed, the manganese concentration range was between 2.9 and 30.8 mug/l.     

Spectrophotometric determination of zinc with hydrazidazol in the presence of Triton X-100 and its application in metal analysis

A new spectrophotometric method for the determination of zinc is proposed. The chromogenic agent Hydrazidazol forms a 1:1 chelate with zinc in the presence of Triton X-100 in a medium containing 20-40% ethanol. The molar absorptivity and conditional formation constant have been found to be 2.7 x 1O(4) l.mole(-1).cm(-1) (at 640 nm) and 10(5.32) respectively. Beer's law is obeyed for zinc over the range of 0.2-0.8 mug/ml with a standard deviation of 0.024 mug/ml. The method can be applied to the determination of zinc in cadmium metal and its oxide after preconcentration by selective extraction of zinc thiocyanate into ethyl acetate in the presence of EDTA and thiosulphate as masking agents.     

Cyclodextrin enhanced spectrofluorimetric determination of fluoxetine in pharmaceuticals and biological fluids

The characteristics of host-guest complexation between methyl-beta-cyclodextrin and fluoxetine were investigated by fluorescence spectrometry. A 1:1 stoichiometry of the complex was established and association constant of 4.35x10(-3) M(-1) at 20 degrees C was calculated. A spectrofluorimetric method for the determination of fluoxetine, with a range of application between 40 and 1000 mug l(-1) was developed. Overall least squares regression was used to find the straight line that fitted the experimental data. The detection limit, according to the error propagation theory, was 9.6 mug l(-1) and the detection limit proposed by Clayton was 15.8 mug l(-1). Repeatability and relative standard deviation were also determined according to this theory, with satisfactory results. The method was successfully applied to the determination of fluoxetine in pharmaceuticals and biological fluids.     

Determination of nitrite by sequential injection analysis of electrokinetic flow analysis system

A new sequential injection analysis (SIA) method of an electrokinetic flow analysis (EKFA) system for the determination of nitrite-nitrogen is presented in this paper. The proposed system mainly consisted of an electroosmotic pump, two solenoid valves and a spectrophotometer etc. All the pump and valves were controlled by a personal computer automatically. The determination method of nitrite-nitrogen was based on the reaction among nitrite, sulfanilamide and naphthylethylenediamine to form a colored compound, which was measured at 540 nm. The linear calibration range of nitrite-nitrogen was 10-800 mug l(-1). The detection limit was 1 mug l(-1) (K=3, n=11). The analytical method can provide a throughput of 33 samples per h.     

Simultaneous determination of manganese and zinc in mixtures using first- and second-derivative spectrophotometry

A new direct spectrophotometric determination of manganese with 5,8-dihydroxy-1,4-naphthoquinone (naphthazarin,NAZA) is reported. Absorption maximum, molar absorptivity and Sandell's sensitivity of 1:2 (M:L) complex are 695 nm, 1.88x10(4) l mol(-1) cm(-1) and 2.92 ng cm(-2), respectively. A linear calibration graph is obtained up to a concentration of 7.2 mug ml(-1) of manganese. The optimum range for determination (Ringbom) is between 0.20 and 6.8 mug ml(-1). A rapid method for simultaneous determination of manganese and zinc in their mixture using derivative spectra is described. The range 0.28-5.6 mug ml(-1) manganese could be determined in the presence of 0.33-6.8 mug ml(-1) zinc and vice versa. The developed method was applied to the simultaneous spectrophotometric determination of manganese and zinc in some synthetic mixtures and was found to give satisfactory results.     

Spectrophotometric determination of gallium in alloys and fly-ash with pyridoxal derivatives of thiocarbohydrazide and carbohydrazide

The symmetric derivatives of pyridoxal with thiocarbohydrazide and carbohydrazide, and the asymmetric derivatives of pyridoxal and salicylaldehyde with the same hydrazides have been synthesized and their analytical potential for spectrophotometric and kinetic fluorimetric determination of metal ions was studied. Gallium(III) and PyMAU(1,3-bis{[4-(2-methyl-3-hydroxy-5-hydroxymethyl)pyridyl]methyleneaminourea at pH = 4.2 form a complex with a single absorption maximum at 425 nm, which can be extracted into cyclohexanone in the presence of a controlled amount of sodium perchlorate. The extract has maximum absorbance at 435 nm. Both systems can be used for determining gallium. The optimal range of gallium concentration for measurement in a 1-cm cell is 0.5-1.25 gmg/ml for the procedure in homogeneous medium ((425) = 3.76 x 10(4).mole(-1).cm(-1)) and 0.25-1.25 mug/ml for the extraction procedure ((435) = 5.30 x 10(4) 1.mole(-1).cm(-1). The latter procedure has been applied to the determination of gallium in alloys and fly-ash.