Extraction of aromatic organic compounds by polyurethane foam

The mechanism of extraction of organic compounds by open-cell polyurethane foam has been investigated through a detailed study with simple aromatic compounds. Comparison with identical extractions into diethyl ether suggests that the basic extraction mechanism is an ether-like solvent extraction process. The addition of salt increases the extraction and changing the dielectric constant of the aqueous solution also affects the extraction. For organic compounds which have a group capable of hydrogen bonding, some additional factor appears to influence the extraction. This appears to be hydrogen bonding with the polyurethane foam; it is stronger with polyether foam and reduced by the presence of a strong intramolecular hydrogen-bonding group placed ortho to the hydrogen-bonding group. Thermodynamic studies support these conclusions.     

The distribution of elements between polyether-type polyurethane foam, cyclic polyethers and hydrofluoric acid solution

The extraction of fifteen elements in the systems ?onsisting of polyurethane foam (polyether type)/HF-alkali-metal fluoride and cyclic polyether/HF-alkali-metal fluoride has been investigated. Little or no extraction was found for Co, Zn, Fe, Zr, Hf, Sn(IV), Nb, Pa, As(V), Mo, and W. Only Ta, Sb, Re, and Tc are well extracted with either polyurethane foam or dicyclohexano-18-crown-6 in dichloro-ethane under the conditions investigated. The mechanism of the extraction is discussed. The most interesting separation possibilities have been tested.     

Extraction of Mo, W and Tc with polyurethane foam and with cyclic polyether from SCN-/HCL medium

The extraction of molybdenum, tungsten and technetium by polyether-based polyurethane foam and by a cyclic polyether from aqueous thiocyanate solutions is described. The influence of the reductants stannous chloride and ascorbic acid has also been studied. The possibilities of the polyurethane foam for preconcentration and determination of molybdenum are discussed.     

Preconcentration and separation of acaricides by polyether based polyurethane foam

This paper reports the preconcentration of some dissolved organic phosphorous and chlorinated acaricides in water by porous polyether based polyurethane foam. Preliminary screening tests on the retention of the tested compounds, i.e., dicofol and bromopropylate, by polyether foams indicated that a very high percent removal of the tested species was obtained. The retention rate was found fast and reaches equilibrium in a few minutes. The various parameters, e.g., pH, extraction media, shaking time, salt effect, temperature and sample volumes affecting the preconcentration of the tested species by the unloaded foam, trioctylamine and trimethylphosphate treated foam have been optimized via batch modes of separation. The unloaded foams were employed in column modes for the retention and recovery of the tested species. The sorption efficiency and recovery of the compounds by the unloaded foams column were found to be up to 97.5%. The height equivalent to a theoretical plate (HETP) obtained by the unloaded foam was found to be in the range 1.1-1.3 ± 0.2 mm. The sorption mechanism of the tested compounds by the foams was discussed.     

Polyurethane foam extraction of platinum-tin halide complexes

The sorptive capacity of the polyether-based foam was determined to be between 0.85 and 0.92 moles/kg for the platinum-tin(II) chloride complex. At hydrochloric and hydrobromic acid concentrations up to 3.0M, the platinum-tin(II) bromide complex had higher extraction efficiencies than the platinum-tin(II) chloride complex. Sorptions were optimized at 5.0M hydrochloric acid and 3.0M hydrobromic acid and distribution ratios as high as 2.0 x 10(5) 1./kg were observed at high foam:platinum ratios. The percent of platinum extracted increased when the alkali metal cations are added in the order K(+) < Na(+) < Li(+) for polyether foam, and decreased in the order K(+) > Na(+) > Li(+) for polyester foam. Also, the sorption efficiencies increased as the proportion of poly(ethylene oxide) of the foam was increased. A Scatchard plot analysis shows that there is a 2:1 ratio of loosely bound platinum to tightly bound platinum with the polyether foam, however, the experimental results are consistent with a weak-base anion exchange mechanism as the prominent method of sorption. For polyester foam, results are consistent with a solvent-like ion-pair sorption mechanism.     

Studies on the extraction of phosphomolybdate by polyether foam

To establish the mechanism of heteropoly anion extraction, the sorption of phosphomolybdate by polyether-based polyurethane foam was investigated. The effect of several variables on the extraction was studied and the optimum conditions were ascertained. The results of this study indicate that the cation-chelation mechanism cannot account for the extraction of phosphomolybdate by polyether foam.     

The separation of tellurium and selenium by polyurethane foam sorbents

Tellurium and selenium can be sorbed from hydrochloric acid and hydrobromic acid solution by both polyether and polyester-based polyurethane foam. Although some acid is needed, the substitution of sodium chloride or sodium bromide increases the extraction significantly. Tellurium is extracted rapidly with > 99% sorbed in 2 min from 1.0/5.0M and 2.0/4.0M hydrochloric acid/sodium bromide. Selenium can also be sorbed quantitatively but much more slowly so that a separation is possible based on the relative rates of extraction. The capacity of polyether foam is 3% by weight of tellurium.     

Extraction mechanism of monovalent ion-pairs by polyurethane foams

The extractability sequence of K(+) approximately Rb(+) > Cs(+) > Na(+) > Li(+) for the extraction with polyether foam suggests that the cation chelation mechanism might be operative. However, the same order was obtained for the extraction with 100% polypropylene oxide polyether foam which does not normally adopt a helical structure to form oxygen-rich cavities as easily or as effectively as polyethylene oxide to accommodate alkali metal ions. This result indicates that a hole-size/cation-diameter relationship may not be required for the high extraction of K(+). The extraction of alkali metal DPAs and hydroxides from methanol demonstrates the importance of the solvent effect. It indicates that the water-structure enforced ion-pairing (WSEIP) is the driving force for extraction of the ion-pairs. The extraction mechanism for ionic species can be described as an ion-pair extraction process. The overall effect of ion-pair formation in water and interaction of the extracted ions with foam appears to determine the extractability of the ions of the extractable ion-pair.     

Utility of 5-Diazo-1,2,4- Triazol-3-Carboxylic Acid for Colorimetric Determination of Certain 8-Hydroxyquinolines

Abstract

A colorimetric method for the determination of certain 8-hydroxyquinolines has been developed. The method is based on the coupling of 8-quinolinols with diazotriazole carboxylic acid in the presence of sodium carbonate (0.5% w/v) at ambient temperature (around 30°C). The resulting azo dyes are stable and give intense absorption in the range of 486–540 nm. Beer's law is valid in the concentration ranges of 1 – 8, 2.5 – 17.5, 5 – 35, 2 – 20, and 2 – 20 mcg/ml for 8-hydroxyquinoline (HQ), 5,7-diiodo-8-hydroxyquinoline (DIQ), 5,7-dibromo-8-hydroxyquinoline (DBQ), 5-chloro-7-iodo-8-hydroxyquinoline (CIQ) and 8-hydroxy-7-iodo-5-quinoline sulfonic acid (SIQ), respectively. The proposed method has been successfully applied for the determination of the studied compounds in pure form and in commercial formulations. The obtained results are in good agreement with those obtained from reported methods.     

Spectrophotometric determination of halogenated 8-hydroxyquinoline derivatives

A spectrophotometric method is proposed for the determination of 8-hydroxyquinoline and three of its iodinated derivatives: 5-chloro-7-iodo-8-hydroxyquinoline (clioquinol), 5,7-di-iodo-8-hydroxy-quinoline (iodoquinol) and 8-hydroxy-7-iodo-quinolone-5-sulphonic acid (chinoform). The suggested method depends on the reaction with 4-aminoantipyrine in the presence of an alkaline oxidizing agent. A red antipyrine dye with an absorption peak at 500 nm is produced in all cases. The reacting ratio has been determined and a reaction mechanism is presented. The proposed method can be applied to the analysis of pharmaceutical preparations containing the compounds studied, and the results obtained compare favourably with those obtained with the standard methods.     

Extraction of ruthenium thiocyanate and its separation from rhodium by polyurethane foam

Conditions for the formation and extraction of the thiocyanate complex of ruthenium are reported. Distribution coefficients of more than 10(4) and a capacity of about 0.24 mole per kg of foam were obtained. The effect of the chloride salts of various univalent cations on the extraction of Ru(SCN)(6)(3-) indicated that the efficiency of ruthenium extraction depends on how well the cation fits into the polyether segment of the polyurethane foam, which agrees with the "cation-chelation" mechanism. The separation of ruthenium and rhodium indicated that more than 95% of the rhodium remained in the aqueous phase and about 95% of the ruthenium was retained by the polyurethane foam and could be easily recovered.     

Sorption of iron(III) and iron(II) from acidic chloride solutions by polyether and polyester type polyurethane foams

Summary Iron(III) is sorbed by polyether type open-cell polyurethane foams from HCl solutions of 4 mol/l or higher. The capacity of the foams is around 50 mg·l^–1. The iron (III) sorbed can be eluted from the foam with 0.01 mol/l HCl or distilled water. An optimization of the sorption conditions showed that the process can be used for analytical applications. The polyurethane foam sorbents examined did not sorb iron(II). The mechanism of sorption by polyether foams seems to follow a mechanism similar to that of the extraction of iron(III) by etheric solvents.     

Extraction of tungsten with 8-hydroxyquinoline and some of its derivatives

The extraction of tungsten by chloroform solutions of 8-hydroxyquinoline(I), 2-methyl-8-hydroxyquinoline(II), 5,7-dibromo-8-hydroxyquinoline(III) and 8-mercaptoquinoline(IV), as a function of the concentration of tungsten and reagent and the acidity of the aqueous phase, has been studied. Evidence was obtained for the quantitative extraction of tungsten over a wide range of acidity. The degree of extraction of tungsten at 10(-5)M concentration with I,III and IV gives two maxima when plotted against acidity. The extraction maximum for the more acidic solutions lies in the region where the reagents exist in the protonated form and its position depends on the reagent used. It is suggested that different tungsten complexes are extracted, depending on the acidity of the aqueous phase.     

Extraction of certain actinide and lathanide elements from different acidic media by polyurethane foams loaded with di-(2-ethylhexyl)phosphoric acid (HDEHP)

The partition of cerium(III) between aqueous acid perchlorate solutions and polyurethane foams loaded with solutions of di-(2-ethylhexyl)phosphoric acid (HDEHP) in nitrobenzene has been investigated and the apparent polymerization number of HDEHP on the foam has been determined. The mechanism of extraction is discussed in the light of the results. It has been found that Ce(III) is generally extracted on the foam by a cation exchange mechanism.     

The use of continuous extraction for the removal of interfering elements in the determination of calcium and magnesium

Solvent extraction with a continuous extractor has been used to separate Al, Be, Bi, Cd, Ce, Cr, Co, Cu, Ga, In, Fe, Pb, Hg, Mo, Ni, Tl, Th, Sn, Ti, W, U, V, Zn and Zr, from calcium and magnesium, before titration of the latter with ethanediaminotetraacetic acid. Most of these elements arc extracted at ca, pH 5.0 as their chelates with 8-hydroxyquinoline using chloroform. Be, Ce and Cr are not extracted under these conditions and are converted into their acetylacetonates, before extraction with chloroform. Manganese is not quantitatively removed by any of these processes and is precipitated as its hydrated dioxide by boiling the extracted solution with sodium chlorite. Phosphate, arsenate and selenate can be removed by precipitating them in acid solution with excess zirconium nitrate, and removing the latter with 8-hydroxyquinoline.     

Extraction of palladium thiocyanate with polyurethane foam

Conditions for the extraction of the thiocyanate complex of palladium by polyether-type polyurethane foam are reported. Distribution ratios of more than 10(6) with a capacity of about 0.8 mole per kg of foam were obtained. The palladium could be rapidly recovered from the foam with high efficiency by use of ammonia solution. The efficiency of palladium extraction depends on how well the cation associated with the complex fits into the polyether segment of the polyurethane foam.     

Liquid-liquid extraction of Th4+ and UO 2 2+ by LIX-26 and its mixtures

Solvent extractions of thorium(IV) and uranium(VI) by a commercially available chelating extractant LIX-26 (an alkylated 8-hydroxyquinoline) or 8-hydroxyquinoline, benzoic or salicylic acid, dipentyl sulphoxide (DPSO) and their mixtures with butanol as modifier in benzene/methylisobutyl ketone (MIBK) as the diluent have been studied. Extraction of uranium(VI) by 10% LIX-26 and 10% butanol in benzene becomes quantitative at pH 5.0. The pH 0.5 values for the extraction of thorium(IV) and uranium(VI) are 4.95 and 3.35, respectively. Quantitative extraction of thorium(IV) by the mixture of 0.1 M oxine and 0.1 M salicylic acid in methylisobutyl ketone was observed at pH 5.0. The influence of concentration of various anions on the extraction of Th⁴⁺ by mixtures of LIX-26 and benzoic acid has been studied. Studies on extraction of thorium(IV) and uranium(VI) by mixtures of LIX-26 (HQ) and DPSO show that the extracted species are possibly of the type [ThQ₂/DPSO/₂/SCN/₂] and [UO₂Q₂/DPSO/], respectively.     

Three-component synthesis and antibacterial evaluation of some novel 1,2-dihydroisoquinoline derivatives

Isoquinoline reacts with dialkyl acetylenedicarboxylates in the presence of kojic acid or8-hydroxyquinoline to generate 1,2-dihydroisoquinoline derivatives. The simplicity, mild reaction conditions and high yields of products make it an interesting process compared to other approaches. The compounds have been analyzed for antibacterial activity against Gram negative and Gram positive bacteria. The results indicated that 1,2-dihydroisoquinolines derived from kojic acid are effective against all of the studied bacteria especially against Bacillus subtilis, while the products obtained from8-hydroxyquinoline are active only against Gram positive bacteria.     

Polyurethane-pyridylazonaphthol foams in the preconcentration and separation of trace elements

The feasibility of using PAN—polyether and polyester polyurethane foams in batch and column operations has been examined. The effects of pH, plasticizer and various anions present in the aqueous solution on the extraction behaviour of cobalt, iron and manganese have been investigated. In dynamic systems, the effect of flow rate on the extraction efficiencies of these metal ions has been investigated. The uptake of cobalt(III) and manganese(II) on PAN—polyester foam columns is quantitative at flow rates up to 10 ml min^-1 and 2 ml min^-1, respectively. The retention of iron(III) by the foam column is not quantitative even at a flow rate of 1 ml min^-1. Preconcentration of cobalt and its separation from various concentrations of manganese are successful..     

Determination of Dialkyltin Compounds in Poly(Vinyl Chloride) by High-Performance Liquid Chromatography

A high-performance liquid chromatography (HPLC) method has been developed for the analysis of dialkyltin compounds in polyvinyl chloride (PVC) materials. The PVC sample was first dissolved in tetrahydrofuran. Concentrated hydrochloric acid was then added to convert the dissolved dialkyltin stabilizers into the chloride forms, followed by extraction with hexane. The extracted dialkyltin chlorides were preconcentrated and were finally separated by HPLC. Separation was performed using a C₁₈ column and an eluent of aqueous methanol containing 8-hydroxyquinoline (oxine) as the completing agent. Photometric detection of the dialkyltin-oxine complexes was carried out at 380 mm. Under optimum experimental conditions, the detection limits for dimethyltin, dibutyltin and dioctyltin are 1.7 ng, 2.1 ng and 2.9 ng (all as tin), respectively. Residual dialkyltin stabilizers in several commercially available PVC products were successfully analyzed via this method.