Construction of a l-lysine biosensor by immobilizing lysine oxidase on a gold-poly(o-phenylenediamine) electrode

The construction of a l-lysine biosensor on a Si-gold strip electrode (SGSE) is described in this study. The construction comprises (a) the formation of poly(o-phenylenediamine, o-PD) membrane on the electrode surface via electropolymerization and (b) the immobilization of lysine oxidase on the gold/poly(o-PD) electrode with glutaraldehyde. The behavior of the gold/poly(o-PD) electrode against H(2)O(2) and lysine, as well as the repeatability of the electropolymerization and the time stability of the polymer were studied. The study showed that the electropolymerization procedure is repeatable, and that the polymer is quite stable for at least 40 days. The biosensor showed a linear calibration curve in the range 0.01-1x10(-5) M (0.1-10 muM) lysine. The interfering effect of other amino acids on the biosensor performance was also studied and amperometric selectivity coefficients were calculated. The biosensor responded mainly against tyrosine and cysteine, while the response to phenylalanine, arginine, histidine and ornithine was very low. By changing the electropolymerization conditions, the effect of interferents was further reduced.     

Design and characterization of a lactate biosensor based on immobilized lactate oxidase onto gold surfaces

The design and characterization of a lactate biosensor and its application to the determination of this analyte in wine and beer are described. The biosensor is developed through the immobilization of lactate oxidase (LOx) using two different strategies including direct adsorption and covalent binding. The characterization of the resulting lactate oxidase monolayers was performed in aqueous phosphate buffer solutions using atomic force microscopy (AFM) and quartz crystal microbalance (QCM) techniques. In presence of lactate and using hydroxymethylferrocene as a redox mediator, biosensors obtained by either direct adsorption or by covalent binding exhibit a clear electrocatalytic activity, and lactate could be determined amperometrically at 300 mV versus SSCE. Results obtained under these conditions give a linear current response versus lactate concentration up to 0.3 mM, with a detection limit of 10 μM of lactate and a sensitivity of 0.77 ± 0.08 μA mM⁻¹. Finally, biosensors were applied to the determination of lactate in wine and beer. The results obtained are in good agreement with those obtained by a well-established enzymatic-spectrophotometric assay kit.     

乳酸氧化酶共价交联于蛋膜上制备乳酸传感器

以牛血清白蛋白 戊二醛为交联剂 ,将乳酸氧化酶固定于鸡蛋膜上 ,氧电极作电化学敏感元件 ,制成乳酸氧化酶电极。传感器的线性响应范围为 5 .0×1 0 - 5～ 2 .5× 1 0 - 2 mol/L ,检测限为 2 .0× 1 0 - 5mol/L ,RSD为 1 .4% (n =1 1 ) ,回收率为 97.5 %～ 1 0 4 .0 %。该传感器可用于临床乳酸的测定。     

Enzyme sensor for L-lactate with a chitosan-mercury film electrode

Summary An amperometric enzyme sensor composed of a mercury film electrode and an enzyme-immobilized chitosan membrane is developed. This biosensor is based on both a mercury film electrode detecting the consumption of dissolved dioxygen following enzymatic reaction, and a chitosan membrane. The latter provides an excellent permselectivity and excludes electroactive interferents. The detection range of this biosensor was 1.0×10^–5–3.0×10^–4 mol/l and the relative standard deviation, R.S.D. at 5.0×10^–5 mol/l was 1.4% (n=3). This biosensor was applied to the direct determination of L-lactate in human serum without pretreatment.     

A sensitive biosensor for lactate based on layer-by-layer assembling MnO2 nanoparticles and lactate oxidase on ion-sensitive field-effect transistors

A sensitive enzyme-based FET biosensor for lactate has been obtained by introducing MnO2 nanoparticles at the gate surface via a layer-by-layer assembling method.     

Sol-gel based amperometric biosensor incorporating an osmium redox polymer as mediator for detection of L-lactate

A novel amperometric biosensor for the determination of lactate was constructed by first immobilizing lactate oxidase and an osmium redox polymer ([Os(bpy)(2)(PVP)(10)Cl]Cl; abbreviated Os-polymer) on the surface of a glassy carbon electrode, followed by coating with a sol-gel film derived from methyltriethoxysilane (MTEOS). The electrooxidation current of this electrode was found to be diffusion controlled. In the presence of lactate, a clear electrocatalytic oxidation wave was observed, and lactate could be determined amperometrically at 400 mV versus Ag AgCl . The concentration range of linear response, slope of linear response and detection limit were 0.1-9 mM, 1.02 microA mM(-1), and 0.05 mM, respectively. Although L-ascorbate was electrooxidized at this potential, uric acid, paracetamol and glucose were found not to interfere.     

Flow injection analysis for L-lactate with immobilized lactate dehydrogenase

Immobilized lactate dehydrogenase (LDH) is used for determination of L-lactate in a continuous flow system. The LDH is immobilized by reaction with glutaraldehyde onto the surface of alkylamino-bonded silica gel and packed into a column in the flow system. The reduction of NAD⁺ occurs simultaneously, and the NADH formed is detected amperometrically. The peak current is linearly related to the L-lactate concentration in the range 1–80 × 10^-6 M; 30 samples h^-1 can be analyzed with a r.s.d. of 0.5–1.5%. The immobilized LDH retains over 90% of its initial activity after repetitive use for 3 months.     

Amperometric bienzymatic biosensor for L-lactate analysis in wine and beer samples

A novel amperometric bienzymatic biosensor has been developed based on the incorporation of Lactate Oxidase (LOx) and Horseradish Peroxidase (HRP) into a carbon nanotube/polysulfone membrane by the phase inversion technique onto screen-printed electrodes (SPEs). In order to improve the sensitivity and reduce the working potential, experimental conditions have been optimized and ferrocene has also been incorporated into the membrane as a redox mediator of the enzymatic reactions, which allows the reduction of H(2)O(2) at -100 mV. Measurements were carried out in phosphate buffer solution at pH 7.5 and under batch conditions. The biosensor response time to L-lactate was only 20 s and showed a good reproducibility (RSD 2.7%). Moreover, the detection limit was 0.05 mg L(-1) of l-lactate with a linear interval range from 0.1 mg L(-1) to 5 mg L(-1). Finally, the biosensor has been applied to the determination of l-lactic acid in different wine and beer samples. Then, the results obtained with the biosensor were compared with the ones obtained using, as a reference method, a commercial kit based on spectrophotometric measurements, obtaining an excellent agreement between the results, validating our approach.     

An alcohol oxidase biosensor using PNR redox mediator at carbon film electrodes

A new amperometric biosensor for ethanol monitoring has been developed and optimised. The biosensor uses poly(neutral red) (PNR), as redox mediator, which is electropolymerised on carbon film electrodes and alcohol oxidase (AlcOx) from Hansenula polymorpha as recognition element, immobilised by cross-linking with glutaraldehyde (GA) in the presence of bovine serum albumin (BSA) as carrier protein. Optimisation of variables affecting the system was performed and, for chronoamperometric measurements, a potential of −0.300 V versus saturated calomel electrode was chosen in 0.1 M sodium phosphate buffer saline at pH 7.5. The optimised biosensor showed a good sensitivity of 171.8 ± 14.8 nA mM⁻¹ and the corresponding detection limit (signal-to-noise-ratio = 3) of 29.7 ± 1.5 μM. Stability studies showed a good preservation of the bioanalytical properties of the sensor, 57.6% of its initial sensitivity remaining after 3 weeks (the sensor was used two to three times per week). No significant interferences were found from compounds usually present in wine. The biosensor was used for the determination of ethanol in Portuguese red and white wines.     

Design of a new hypoxanthine biosensor: xanthine oxidase modified carbon film and multi-walled carbon nanotube/carbon film electrodes

A new and simple-to-prepare hypoxanthine biosensor has been developed using xanthine oxidase (XOD) immobilised on carbon electrode surfaces. XOD was immobilised by glutaraldehyde cross-linking on carbon film (CF) electrodes and on carbon nanotube (CNT) modified CF (CNT/CF). A comparison of the performance of the two configurations was carried out by the current response using amperometry at fixed potential; the best characteristics being exhibited by XOD/CNT/CF modified electrodes. The effects of electrolyte pH and applied potential were evaluated, and a proposal is made for the enzyme mechanism of action involving competition between regeneration of flavin adenine dinucleotide and reduction of hydrogen peroxide. Under optimised conditions, the determination of hypoxanthine was carried out at ?0.2 V vs. a saturated calomel electrode (SCE) with a detection limit of 0.75 μM on electrodes with CNT and at ?0.3 V vs. SCE with a detection limit of 0.77 μM on electrodes without CNT. The applicability of the biosensor was verified by performing an interference study, reproducibility and stability were investigated, and hypoxanthine was successfully determined in sardine and shrimp samples.     

Amino oxidase amperometric biosensor for polyamines

An improved amino oxidase enzyme electrode has been constructed and applied to the determination of the amount of polyamines present in real samples. The electrode is based on the amperometric detection of H₂O₂ produced in the enzymatic oxidation of polyamines by amino oxidase. Amino oxidase from soybean seedlings, characterized by an extremely high activity for cadaverine and putrescine, was used. The enzyme was immobilized in an agarose matrix in the presence of glutaraldehyde and bovine serum albumin on the surface of a Pt electrode. Cadaverine, in concentrations between 0.5 and 500 μM, can be quantitatively determined by use of the amino oxidase electrode, the linear calibration range being 0.5–10 μM. The lower detection limit was 0.2 μM and the response time was 15 to 60 s. Putrescine showed similar behaviour. The maximum current response for cadaverine was 5.1 μA/cm², with an apparent Michaelis-Menten constant (K_m′) of 0.175 mM. The sensor response was stable for more than 32 hours of continuous operation at room temperature and, in the presence of fish or meat homogenates, no change in the signal-to-noise ratio was observed. The long-term stability, pH and temperature response of the biosensor has also been studied.     

Fabrication of a new ECL biosensor for choline by encapsulating choline oxidase into titanate nanotubes and Nafion composite film

A simple strategy for encapsulating choline oxidase (ChOD) into the titanate nanotubes (TNTs) and Nafion composite film for choline sensing was proposed. Hydrogen peroxide, as the product of the redox enzymatic reaction, could enhance the ECL of luminol. Therefore, the substrates of corresponding redox enzymes could be detected indirectly through the determination of hydrogen peroxide in the luminol ECL system. Through this approach, it was found that ChOD could be fixed firmly into the TNTs contained composite film. TNTs would not only offer excellent photocatalytic activity toward luminol-H₂O₂ ECL system, but also provide a shelter for the biomolecules, such as redox enzyme to retain its bioactivity.     

Construction of biosensor for hypoxanthine determination by immobilization of xanthine oxidase and uricase in polypyrrole-paratoluenesulfonate film

Journal of Solid State Electrochemistry - A highly selective and stable amperometric biosensor for the determination of the hypoxanthine (Hx) molecule was designed in this study. For this purpose,...     

Ordered mesoporous polyaniline film as a new matrix for enzyme immobilization and biosensor construction

Ordered mesoporous polyaniline film has been fabricated by electrodepositing from the hexagonal lyotropic liquid crystalline (LCC). Horseradish peroxidase (HRP), as a symbol biomolecule, was successfully immobilized on the film to construct a new kind of hydrogen peroxide biosensor. The biosensor combined the advantages of the good conductivity of polyaniline and the higher surface area of the ordered mesoporous film. Polyaniline could be served as a wire to relay electron between HRP and the electrode. The high surface area of the film supplied more sites for HRP immobilization, therefore increased the catalytic activity of the biosensor. The ordered mesoporous character of the film increased the rate of mass transport, which resulted in the improvement of sensor response and linearity. The biosensor displayed excellent electrocatalytic response to the detection of H₂O₂ in a concentration range from 1.0 μM to 2.0 mM with a detection limit of 0.63 μM. Good reproducibility, stability, high precision, wide linearity and low detection limit were assessed for the biosensor.     

An amperometric biosensor for glucose based on electrodeposited redox polymer/glucose oxidase film on a gold electrode.

In this paper, we described a glucose biosensor based on the co-electrodeposition of a poly(vinylimidazole) complex of [Os(bpy)2Cl](+/2+) (PVI-Os) and glucose oxidase (GOX) on a gold electrode surface. The one-step co-electrodeposition method provided a better control on the sensor construction, especially when it was applied to microsensor construction. The modified electrode exhibited the classical features of a kinetically fast redox couple bound to an electrode surface and the redox potential of the redox polymer/enzyme film was 0.14 V (vs. SCE). For a scan rate of up to 200 mV s(-1), the peak-to-peak potential separation was less than 25 mV. In the presence of glucose, a typical catalytic oxidation current was observed, which reached a plateau at 0.25 V (vs. SCE). Under the optimal experimental conditions, the steady-state electrooxidation current measured at 0.30 V (vs. SCE) was linear to the glucose concentration in the range of 0-30 mM. Successful attempts were made in blood sample analysis.     

Novel electrosynthesis of CdS/FeS nanocomposite-modified poly(o-phenylenediamine) with views to their use as a biosensor for Escherichia coli

This article proposes a new electrochemical sensor for Escherichia coli (E. Coli) composed of poly(o-phenylenediamine) (PoPD) and CdS/FeS nanocomposites (PoPD|CdS/FeS). The preparation of the modified electrodes used for this purpose and their subsequent use as a sensor comprise a simple, fast and reproducible technique. The characterization of the CdS/FeS nanocomposites and their subsequent inclusion on PoPD was performed by X-ray diffraction (XRD), Raman, field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HR-TEM) and computational methods; For the nanocomposites an average size of 100 nm was obtained after applying a reduction potential for 5 s over the polymeric matrix. The electrochemical characterizations confirmed that the inclusion of the nanocomposites improved the amperometric response, allowing the developed material to be used as an electrochemical sensor for E. Coli. The figures obtained gave the linear equation j = -6.89 × 10⁻¹⁴ × CFU + 5.64 × 10⁻⁵, with an R² of 0.995, for 10 replicates. Furthermore, the limit of detection (LOD) was 6.1 × 10⁵ CFU/mL, and the limit of quantification (LOQ) was 6.1 × 10⁶ CFU/mL.     

Lactate biosensor based on a bionanocomposite composed of titanium oxide nanoparticles, photocatalytically reduced graphene, and lactate oxidase

We have developed a lactate biosensor based on a bionanocomposite (BNC) composed of titanium dioxide nanoparticles (TiO₂-NPs), photocatalytically reduced graphene, and lactate oxidase. Graphene oxide was photochemically reduced (without using any chemical reagents) in the presence of TiO₂-NPs to give graphene nanosheets that were characterized by atomic force microscopy, Raman and X-ray photoelectron spectroscopy. The results show the nanosheets to possess few oxygen functionalities only and to be decorated with TiO₂-NPs. These nanosheets typically are at least 1 μm long and have a thickness of 4.2 nm. A BNC was obtained by mixing lactate oxidase with the nanosheets and immobilized on the surface of a glassy carbon electrode. The resulting biosensor was applied to the determination of lactate. Compared to a sensor without TiO₂-NPs, the sensor exhibits higher sensitivity (6.0 μA mM^?1), a better detection limit (0.6 μM), a wider linear response (2.0 μM to 0.40 mM), and better reproducibility (3.2 %).

Immobilization of lactate as an electroactive indicator on pencil graphite electrode for the development of a new electrochemical biosensor for the detection of lactate dehydrogenase

A biosensor was developed for the detection of lactate dehydrogenase (LDH) enzyme using a lactate modified pencil graphite electrode (PGE). The sensor relies on the immobilization of the lactate on PGE, and LDH detection is based on the decrease of lactate peak current following oxidation to pyruvate in the presence of LDH. Square wave voltammetric technique was used for the assay of signals in the range of ?0.6 to 0.8 V and a frequency of 25 Hz for the determination of LDH. The dependence of the response was investigated in terms of reaction time, washing time and LDH and NAD⁺ amounts. Also, the electrochemical behavior of LDH treatment on the lactate modified PGE was studied. The electrode showed good selectivity, repeatability and an operational stability of about 90% of its original response for two weeks. Moreover, the sensor displayed a linear response range from 0.36?C2.13 U ??l^?1 for LDH with a detection limit of 0.16 U ??l^?1. The response time of the LDH-treated lactate modified PGE was found to be 2 s. The relative standard deviation (RSD) obtained was 3.5% (for LDH 0.71 U ??l^?1 and n = 3).     

Immobilization of lactate dehydrogenase on tetraethylorthosilicate-derived sol-gel films for application to lactate biosensor

Tetraethylorthosilicate (TEOS)-derived sol-gel films were utilized for the immobilization of lactate dehydrogenase (LDH) by physical adsorption and sol-gel/LDH/sol-gel sandwich configuration. An attempt was made to ascertain the optimum pH and temperature for the immobilized LDH. It was shown that TEOS-derived sol-gel films containing physically adsorbed LDH exhibited linearity from 0.5 to 4 mM, whereas those containing LDH in sandwich configuration showed linearity from 0.5 to 3 mM l-lactate. These sol-gel films, immobilized with LDH, were found to be stable for about 4 weeks at 4–10°C.     

Direct electrochemistry of glucose oxidase in a colloid Au-dihexadecylphosphate composite film and its application to develop a glucose biosensor

Colloid Au (Au(nano)) with a diameter of about 10 nm was prepared and used in combination with dihexadecylphosphate (DHP) to immobilize glucose oxidase (GOD) onto the surface of a graphite electrode (GE). The direct electrochemistry of GOD confined in the composite film was investigated. The immobilized GOD displayed a pair of redox peaks with a formal potential of -0.475 mV in pH 7.0 O(2)-free phosphate buffers at scan rate of 150 mV s(-1). The GOD in the composite film retained its bioactivity and could catalyze the reduction of dissolved oxygen. Upon the addition of glucose, the reduction peak current of dissolved oxygen decreased, which could be developed for glucose determination. A calibration linear range of glucose was 0.5-9.3 mM with a detection limit of 0.1 mM and a sensitivity of 1.14 microA mM(-1). The glucose biosensor showed good reproducibility and stability. The general interferences that coexisted in human serum sample such as ascorbic acid and uric acid did not affect glucose determination.