葵二酸对纳米ZnO的有机表面修饰研究

利用葵二酸对纳米ZnO进行有机表面修饰。采用红外光谱(IR)、热分析(TG-DTA)、X射线光电子能谱(XPS)、透射电镜(TEM)、润湿性实验、分散性实验等对表面改性前后的纳米ZnO进行表征。红外光谱、TEM及XPS表明，在纳米ZnO表面包覆有葵二酸的有机层。热分析显示，包覆量约为14.5%。润湿性及分散性实验表明，经葵二酸改性的纳米ZnO的表面性质由亲水变为疏水。     

硫代-iniferters法改性弹性蛋白的研究

弹性蛋白经对氯甲基苯甲酰氯氯化、二乙基二硫代氨基甲酸钠(NaSD)硫化制备了大分子iniferter剂(E-S), 再以E-S为引发剂, 在紫外光(UV)照射下引发甲基丙烯酸-β-羟乙酯(HEMA)聚合, 合成了聚甲基丙烯酸-β-羟乙酯(E-PHEMA)改性的弹性蛋白聚合物. 用红外(FTIR)和X射线光电子能谱(XPS)、热重分析(TGA)、扫描电镜(SEM)和动态接触角对改性弹性蛋白进行了表征. 结果表明: PHEMA键接到了弹性蛋白上; SEM显示改性后弹性蛋白的表面比未改性前变得光滑, 但改性后样品的热性能均低于未改性样品, 起始热分解温度由改性前的307.0 ℃变为260.2 ℃, 最大失重速率温度由347 ℃降到316.3 ℃; 动态接触角实验表明改性后样品具有良好的亲水性, 反应72 h后前进角由改性前的130.45°下降到35.40°, 接触角滞后由70.42°变为35.40°.     

Surface modification of ultra‐high molecular weight polyethylene fibers by chromic acid

Ultra‐high molecular weight polyethylene (UHMWPE) fibers were modified by chromic acid. The effects of surface modification were evaluated with Fourier transform infrared spectroscopy (FTIR), X‐ray photoelectron spectroscopy (XPS), contact angle measurement, and scanning electron microscope (SEM). The results showed that both the content of O‐containing functional groups and surface roughness of modified fibers increased. The polar groups on the modified fiber surface decreased the contact angles with water and ethylene glycol, as evidenced by contact angle measurement. The tensile test results showed the strength and the elongation at break of UHMWPE fibers decreased but the modulus increased after chromic acid modification. Copyright © 2016 John Wiley & Sons, Ltd.     

ATRP法合成弹性蛋白接枝共聚物及其性能研究

弹性蛋白经α-溴异丁酰溴化制备了大分子ATRP引发剂溴化弹性蛋白(E-Br), 再以E-Br作为引发剂, 在CuCl/2,2-联吡啶催化体系下, 用原子转移自由基聚合方法合成了弹性蛋白-g-聚甲基丙烯酸-β-羟乙酯接枝聚合物. 用红外光谱(FTIR)、X射线光电子能谱(XPS)、热重分析(TGA)、扫描电镜(SEM)、离子色谱和动态接触角对接枝聚合物进行了表征. 结果表明, PHEMA键接到了弹性蛋白表面; SEM显示接枝改性后弹性蛋白的表面比未改性前光滑, 但改性后样品的热性能均比未改性样品的低, 起始热分解温度由改性前的307 ℃变为265 ℃; 动态接触角实验结果表明, 接枝改性后的样品具有良好的亲水性, 反应72 h后, 其前进角由接枝前的130.45°下降到29.80°.     

Triazole-forming waterborne polyurethane composites fabricated with silane coupling agent functionalized nano-silica

In the research work, "click" chemistry was used to modify waterborne polyurethane (WPU) with silane coupling agent (SiCA) functionalized nano-silica. The modified WPU (CWPU) was characterized by FTIR, scanning electron microscope (SEM), thermogravimetric analysis (TGA) and contact angle measurement. The experiment results show that the modification can improve the thermal stability, hardness, and water or weather resistance of CWPU.     

Characterization of electron-beam-modified surface coated clay fillers and their influence on physical properties of rubbers

A novel process of surface modification of clay filler has been developed by coating this with an acrylate monomer, trimethylol propane triacrylate (TMPTA) or a silane coupling agent, triethoxy vinyl silane (TEVS) followed by electron beam irradiation. Characterization of these surface modified fillers has been carried out by Fourier-transform infrared analysis (FTIR), electron spectroscopy for chemical analysis (ESCA), wettability by dynamic wicking method measuring the rise of a liquid through a filler-packed capillary tube and water flotation test, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), thermogravimetric analysis (TGA), and X-ray diffraction (XRD). Presence of the acrylate and the silane coupling agent on the modified fillers has been confirmed from FTIR, ESCA, and EDX studies, which has also been supported by TGA studies. The contact angle measurement by dynamic wicking method suggests improvement in hydrophobicity of the treated fillers, which is supported by water flotation test especially in the case of silanized clay. However, XRD studies demonstrate that the entire modification process does not affect the bulk properties of the fillers. Finally, both unmodified and modified clay fillers have been incorporated in styrene butadiene rubber (SBR) and nitrile rubber (NBR). Rheometric and mechanical properties reveal that there is a definite improvement using these modified fillers specially in the case of silanized clay compared to the control sample, probably due to successful enhancement in interaction between the treated clay and the base polymer.     

邻苯二酚-四乙烯五胺改性超高分子量聚乙烯纤维

应用Cat-TEPA改性超高分子量聚乙烯(UHMWPE)纤维,在难黏附的纤维表面形成均匀涂层.采用透射电子显微镜(TEM)、红外光谱(FTIR)、X射线光电子能谱(XPS)、X射线衍射(XRD)、示差扫描量热(DSC)、热重分析(TGA)和静态接触角测试等手段对其结构和性能进行了表征,并通过单丝拔出实验研究改性前后纤维与环氧树脂之间的界面剪切强度(IFSS),探索了反应物配比、反应时间对表面性能的影响,并确定最佳改性条件.结果表明Cat-TEPA共沉积改性未影响纤维的结晶和热稳定性,改性后纤维表面浸润性得到改善,且适当增加反应时间和TEPA含量能够提高纤维和树脂之间的IFSS,当Cat-TEPA摩尔比为1:4,反应时间为24 h时效果最佳,与未改性纤维相比,界面剪切强度提升约44%.     

大分子偶联剂马来酸酐-丙烯酸丁酯-苯乙烯三元共聚物的合成及其对纳米氮化铝的表面改性

采用自由基溶液聚合法合成了马来酸酐（MAn）-丙烯酸丁酯（BA）-苯乙烯（St）三元共聚物大分子偶联剂,并用其对纳米氮化铝（AlN）粉体进行了表面改性。通过GPC、FTIR、沉降实验、TGA、接触角以及TEM的分析表明,合成的大分子偶联剂,数均相对分子量在3 000~10 000之间,适于对纳米粉体进行包覆;单体投料摩尔比为１:１:５的MAn-BA-St三元共聚物大分子偶联剂对纳米AlN的改性效果最好,其化学利用率为52.5%,物理利用率为25%;改性后纳米AlN的表面自由能从879 J/M²降至221 J/M²,在苯乙烯中分散良好。     

Surface modification of plasma‐pretreated expanded poly (tetrafluroethylene) films by graft copolymerization

A two‐step process based on a low‐pressure helium plasma treatment followed by acrylic acid‐grafting copolymerization was used for the surface modification of expanded polytetrafluoroethylene (ePTFE) films. The effects of plasma treatment power and treatment time on the hydrophilicity of the film surface were investigated. The wettability of the ePTFE film surface was characterized by water contact angle, and the surface compositions of the untreated and treated ePTFE samples were evaluated by atomic force microscopy and XPS. Contact angle measurements revealed that the hydrophilicity of the ePTFE film surface was greatly enhanced by the combined actions of the plasma treatment and acrylic acid grafting, and the contact angle decreased from 145° to 66°. Atomic force microscopy analyses showed that the surface roughness increased after the plasma treatment. XPS analyses showed substantial increase in the concentration of carbon and oxygen atoms and a decrease in the concentration of fluorine atoms at the film surface. T‐peel strength showed an improved bonding strength between the film and an adhesive tape after the treatment. Copyright © 2012 John Wiley & Sons, Ltd.     

聚乙二醇单甲醚修饰多壁碳纳米管的研究

多壁碳纳米管(MWNT)经过酸化、酰氯化后与聚乙二醇单甲醚进行接枝反应,实现了碳纳米管的表面修饰。经修饰的MWNT在水中的分散性大大增加。通过FTIR、XPS、Raman、TEM、TGA等手段表征了接枝后产物的化学结构,证明聚乙二醇单甲醚是以共价键的形式接入MWNT表面上的。并利用TGA结果估算出聚乙二醇单甲醚在MWNT表面的接枝密度约为平均每256个碳原子上有一根聚合物链。     

Synthesis and Characterization of β‐CD‐Coated Polystyrene Microspheres by γ‐Ray Radiation Emulsion Polymerization

Polystyrene (PS) microspheres coated with β‐cyclodextrin (β‐CD) were fabricated via γ‐ray‐induced emulsion polymerization in a ternary system of styrene/β‐CD/water (St/β‐CD/water). The solid inclusion complex of St and β‐CD particles formed at the St droplets–water interface can stabilize the emulsion as the surfactant. TEM and XPS results showed that β‐CD remains on the surface of PS particles. The average size of the PS particles increases from 186 to 294 nm as the weight ratio of β‐CD to St rises from 5% to 12.5%. The water contact angle (CA) of PS latex film is lower than 90°, and reduces with the β‐CD content even to 36°. Thus, this work provides a new and one‐pot strategy to surface hydrophilic modification on hydrophobic polymer particles with cyclodextrins through radiation emulsion polymerization.     

<Emphasis Type="Italic">In situ</Emphasis> synthesis and modification of calcium carbonate nanoparticles via a bobbling method

Modified calcium carbonate (CaCO₃) nanoparticles with cubic- and spindle-like configuration were synthesized in situ by the typical bobbling (gas-liquid-solid) method. The modifiers, such as sodium stearate, octadecyl dihydrogen phosphate (ODP) and oleic acid (OA), were used to obtain hydrophobic nanoparticles. The different modification effects of the modifiers were investigated by measuring the active ratio, whiteness and the contact angle. Moreover, transmission electron microscopy (TEM), X-ray diffraction (XRD) and thermogravimetry analysis (TGA analysis) were employed to characterize the obtained products. A preliminary reaction mechanism was discussed. According to the results, the active ratio of CaCO₃ modified by ODP was ca. 99.9% and the value of whiteness was 97.3% when the dosage of modifiers reached 2%. The contact angle was 122.25° for the CaCO₃ modified in the presence of sodium stearate, ODP and OA. When modified CaCO₃ was filled into PVC, the mechanical properties of products were improved greatly such as rupture intensity, pull intensity and fuse temperature. The compatibility and affinity between the modified CaCO₃ nanoparticles and the organic matrixes were greatly improved. Supported by the National Natural Science Foundation of China (Grant No. 50372025)     

碳酸钙的原位合成及表面改性

利用碳化法, 选用几种常见的改性剂(硬脂酸钠、十八碳醇磷酸酯和油酸)对碳酸钙进行了原位合成及表面改性. 通过活化度、白度、接触角的测定, 对比了其改性效果, 同时通过傅里叶变换红外光谱(FT-IR)、X射线衍射(XRD)、透射电镜(TEM)等测试手段对产品进行表征. FT-IR结果表明, 改性剂与碳酸钙表面是以化学键合和物理吸附方式相结合. 碳酸钙改性后, 其红外υ3特征吸收峰出现约44 cm-1的蓝移现象. 对反应机理进行了初步探讨. 实验结果表明, 当十八碳醇磷酸酯用量达到2%(以碳酸钙的质量分数计)时, 产品活化度达到99.9%, 白度值达到97.3%, 接触角达到了122.25°, 从而为新型无机填料的制备提供了理论依据和合成手段.     

水相湿法改性纳米碳酸钙表面性质的研究

用特定的表面改性剂在水相中对纳米碳酸钙的悬浮液进行了湿法改性。红外光谱和热失重分析证明,改性剂与碳酸钙之间以化学键结合;沉降体积和接触角的测定结果说明改性粒子在液体石蜡中的润湿性和疏水性得到了提高;透射电子显微镜照片显示改性粒子在液体石蜡中有更好的分散性;体系粘度实验表明改性粒子与液体石蜡之间有较好的相容性。     

Study of hydrophilicity and stability of chemically modified PDMS surface using piranha and KOH solution

Successful realization of various BioMEMS devices demands effective surface modification techniques of PDMS elastomer. This paper presents a detailed report on a simple and cost effective approach for surface modification of PDMS films involving wet chemical treatment in two‐step processes: primarily involving piranha solution followed by KOH dip to improve hydrophilicity and stability of PDMS surface. Chemical composition of the solution and surface treatment condition have been varied and optimized to significantly increase the surface energy. The effect of surface modification of the elastomer after wet chemical treatment is analyzed using contact angle measurement and FTIR‐ATR study. PDMS surface treated in piranha solution with H₂O₂ and H₂SO₄ in the ratio of 2:3 followed by a dip in KOH solution for 15 min duration each, demonstrated a maximum reduction of contact angle to ～27° as compared to untreated sample having a contact angle of ～110°. The removal of hydrophobic methyl group from elastomer surface and subsequent hydrophilization of surface by wet chemical process was confirmed from FTIR‐ATR spectra. This result is also supported by improved adhesion and electrical continuity of deposited aluminum metal film over the modified PDMS surface. Copyright © 2011 John Wiley & Sons, Ltd.     

纳米CaCO3的改性、表面结构与流变行为研究

采用铝锆偶联剂和棕榈酸改性纳米CaCO₃ 粉体. 借助 XRD, FTIR, 接触角及流变学等测试方法对纳米CaCO₃ 的表面结构进行表征. XRD 分析表明: 改性纳米 CaCO₃保持原样品完整的体相结构, 为方解石型纳米微晶. FTIR 分析证明: 表面改性剂与纳米 CaCO₃ 表面是以化学键合和物理吸附方式相结合, 粒子表面存在羧基等有机官能团的红外吸收特征. 通过测定苯和水在改性纳米CaCO₃粉末压片上的接触角, 计算了改性纳米 CaCO₃的表面能和极性分量, 并与未改性纳米CaCO₃ 进行比较. 结果表明, 经表面改性, 纳米 CaCO₃ 的表面能和极性分量明显降低, 其在有机溶液中的吸附功增大, 界面张力大大降低; 经棕榈酸改性的纳米 CaCO₃ 表现出较好的亲油疏水性, 而铝锆偶联剂改性的纳米 CaCO₃ 同时具有亲水性和亲油性. 以液体石蜡为溶剂, 研究了表面改性对纳米CaCO₃悬浮液流变行为的影响. 实验发现: 经过表面处理, 纳米 CaCO₃ 粉体悬浮液流变行为发生较大的变化, 稳态剪切黏度大大降低, 表现出较小的动态弹性储能模量和黏性损耗模量, 而损耗因子较大.     

Starch nanocrystals with large chain surface modifications

Nanoscale monocrystalline starch particles were successfully modified using stearic acid chloride and poly(ethylene glycol) methyl ether. Surface modification was confirmed using FTIR, XPS spectroscopy, and contact angle measurements. X-ray diffraction and DSC analysis confirmed that there was no alteration of the starch crystalline structure due to the surface modification. The grafts at the starch surface were also found to crystallize on the surface. TEM showed the individualization of nanoparticles as a result of the reduction of polar and hydrogen bonding forces. These results show our ability to modify the starch nanocrystal surface with plasticizing chains. Modified nanoparticles can find applications as compatibilized polymer additives, surface-active particles, and co-continuous nanocomposite precursors.     

硅烷偶联剂制备及对磷灰石-硅灰石生物玻璃陶瓷的表面改性

采用谷氨酸与硅烷偶联剂(KH-792)缩合反应,制备出一种含酰胺基的硅烷偶联剂,利用其与材料之间的化学结合,将谷氨酸共价固定至磷灰石-硅灰石生物玻璃陶瓷表面,实现表面改性。将改性后的磷灰石-硅灰石生物玻璃陶瓷与人骨肉瘤细胞MG63共培养,评价其体外细胞生物相容性。应用FTIR、SEM、XPS等测试技术分别对合成的偶联剂、改性后的陶瓷材料进行结构、表面形貌及细胞生长情况的表征,结果表明:谷氨酸与KH-792的反应产物有酰胺基生成;含酰胺基的硅烷偶联剂能对磷灰石-硅灰石生物玻璃陶瓷表面进行有效改性;共培养3 d后细胞在材料材料表面大量贴附,MTT实验也证明增殖良好,即含酰胺基的硅烷偶联剂能改善磷灰石-硅灰石生物玻璃陶瓷的体外细胞生物相容性。     

EFFECT OF SILANE COUPLING AGENT ON THE MECHANICAL, THERMAL PROPERTIES AND MORPHOLOGY OF TREMOLITE/PA1010 COMPOSITES

Tremolite,a kind of inorganic filler,was modified with a silane coupling agentγ-methacryloxypropyl trimethoxy silane (MPS) in ethanol/ammonia solution.The graft of MPS on tremolite was confirmed by X-ray photoelectron spectroscopy (XPS),IR and thermogramitric analysis (TGA) measurements.In addition,contact angle analysis showed that particle surface property was changed from hydrophilicity to hydrophobicity after the modification.Modified tremolite and pure tremolite were blended respectively with PA1010...     

表面接枝含氟苯乙烯共聚物的聚酯薄膜制备与表征

利用表面引发原子转移自由基聚合(SI-ATRP)在聚对苯二甲酸乙二醇酯(PET)薄膜表面接枝苯乙烯和4-氟苯乙烯的共聚物.研究不同反应时间和不同配比下接枝共聚物对聚酯薄膜表面组成、结构和性能的影响.通过傅利叶变换红外光谱仪(ATR/FTIR),X-射线光电子能谱仪(XPS),凝胶渗透色谱(GPC)和扫描电子显微镜(SEM)对接枝改性前后PET薄膜的表面组成,结构和形貌进行分析;利用接触角测试和表面能计算对比研究接枝改性前后PET薄膜的表面性能.结果表明反应时间和单体百分含量对接枝百分率及接触角有一定的影响,随着反应时间的增长,聚酯薄膜表面接枝百分率增大,接触角增加,表面自由能下降.