乌洛托品对模拟汽车冷却液中镁合金的缓蚀作用

镁合金具有高比强度、比刚度以及良好的铸造性、切削性、抗冲击减震性、导热性、无毒性和可回收性等优点,被认为是汽车工业中极好的铝合金及有色金属替代品[1]。用镁合金制造汽车部件,特别是发动机等大重量部件,可以大大减轻车身重量,进而降低能源消耗和废气污染。但是由于镁合     

Application of AC-SECM in corrosion science: local visualisation of inhibitor films on active metals for corrosion protection

The suitability of frequency-dependent alternating-current scanning electrochemical microscopy (4D AC-SECM) for investigation of thin passivating layers covering the surface of corrosion-inhibited metals has been demonstrated. Inhibition of copper corrosion by benzotriazole (BTAH) and methylbenzotriazole (MBTAH), which are effective inhibitors for this metal under many environmental conditions, was investigated. Strong dependencies were found for the AC z-approach curves with both the duration of the inhibitor treatment and the frequency of the AC excitation signal applied in AC-SECM. Both negative and positive feedback behaviours were observed in the AC approach curves for untreated copper and for Cu/BTAH and Cu/MBTAH samples. Negative feedback behaviour occurred in the low-frequency range, whereas a positive feedback effect was observed at higher frequencies. A threshold frequency related to the passage from negative to positive regimes could be determined in each case. The threshold frequency for inhibitor-modified samples was found always to be significantly higher than for the untreated metal, because the inhibitor film provides electrical insulation for the surface. Moreover, the threshold frequency increased with increasing surface coverage by the inhibitor. 4D AC-SECM was successfully applied to visualizing spatially resolved differences in local electrochemical activity between inhibitor-free and inhibitor-covered areas of the sample.     

Corrosion inhibition by benzotriazole derivatives and sodium dodecyl sulphate as corrosion inhibitors for copper in ground water at different temperatures

1‐(2‐Pyrrole carbonyl) benzotriazole (PBTA) and 1‐(2‐thienyl carbonyl)‐benzotriazole (TBTA) were synthesized. Different concentrations of PBTA, TBTA, sodium dodecyl sulphate (SDS), and molybdate (Mo) were evaluated as corrosion inhibitors for copper in ground water medium at different temperatures. The obtained results were compared with the effect of benzotriazole (BTA) on the inhibition of copper corrosion at the same condition. The study was performed using potentiodynamic polarization, electrochemical impedance spectroscopy, cyclic voltammetry, and scanning electron microscopy investigations. A good inhibition is ensured at elevated temperatures. All measurements indicated that PBTA, TBTA, and BTA act as good corrosion inhibitors and their inhibition efficiency (IE%) increased with combining them with optimum concentration of SDS and Mo. Furthermore, the best performance was recorded for the compound PBTA + SDS + Mo, which was found to offer increased IE% in a synergistic manner, thereby acting as a good corrosion inhibitor for copper in ground water medium. Copyright © 2015 John Wiley & Sons, Ltd.     

Characterization of formate complexes formed as corrosion products on copper by raman spectroscopy

Different copper formate complexes formed on the surface of metallic copper have been studied by Raman spectroscopy. Their Raman spectra have been correlated with the dehydrated copper formate, the copper formate dihydrate and the copper formate tetrahydrate. Experiments with deuterated formic acid reveal the influence of water molecules coordinated to the copper ion on the position of Raman bands of the formate ion.     

The effect of gas environment on rolling oil removal from cold-rolled steel as studied by TG

Summary This study investigates mechanisms of cold rolling oil removal from the surface of low-carbon steel. The removal process has been probed using thermogravimetric analysis techniques. A range of furnace atmospheres, from non-oxidizing through to highly oxidising, have been used to simulate the oil removal conditions in the industrial process. The activation energies of oil removal under each gas atmosphere have been determined by MTG and the Flynn-Wall-Ozawa method. The results show that a reducing atmosphere is the optimal environment for effective oil removal. Steel-oil surface interactions have also been investigated to show that the steel substrate catalyses oil removal.     

Electropolymerized coatings of polyaniline on copper by using the galvanostatic method and their corrosion protection performance in HCl medium

The synthesis of polyaniline coatings on the copper (Cu) surface has been investigated by using the galvanostatic method. The synthesized coatings were characterized by Fourier transform infrared spectroscopy, UV–visible absorption spectrometry and scanning electron microscopy. The anticorrosion performances of polyaniline coatings were investigated in 0.5 M HCl medium by the potentiodynamic polarization technique and electrochemical impedance spectroscopy. The corrosion rate of polyaniline‐coated Cu was found to be ～27 times lower than bare Cu, and potential corrosion increased from ?0.21 V versus Ag/AgCl for uncoated Cu to ?0.19 V versus Ag/AgCl for polyaniline‐coated Cu electrodes. Electrochemical measurements indicate that polyaniline coating has good inhibiting properties with a mean efficiency of ~96% at 10 mAcm^?2 current density applied on Cu corrosion in acid media. The results of this study clearly ascertain that the polyaniline has an outstanding potential to protect Cu against corrosion in an acidic environment. Copyright © 2014 John Wiley & Sons, Ltd.     

Inhibitory action of aqueous Ruellia Tuberosa L leaves extract on the corrosion of copper in HCl solution

The inhibitive action of the aqueous extract of Ruellia tuberosa L (ART) on the corrosion of copper in 0.5 ​M HCl was investigated. The inhibition efficiency increased with the extract concentration, acid concentration, as well as increasing the temperature. The Polarization studies revealed that the ART act as a mixed-type inhibitor. Based on the analysis of electrochemical impedance spectroscopy, an equivalent circuit is suggested. The adsorption of the inhibitor ART on the copper surface obeyed the Langmuir adsorption isotherm. From the results of scanning electron microscopy, Fourier transform infrared spectroscopy, and energy-dispersive X-ray spectroscopy the adsorption of ART on the copper surface is confirmed.     

Analytical characterization of corrosion products of copper and its alloys on stained stone surfaces

Monuments, where stone and metals or metallic alloys are used together, are very frequently met in all historical periods and in all countries. In the case of bronze and other copper alloys, their corrosion products can be dissolved by the action of acid rain and thus reach the porous building materials in contact with (or near to) the metallic structures. Once absorbed by the stone, they precipitate on the external stone surface and inside its porous space. As the majority of these products are coloured, their precipitates may produce stains, which are perceived as unpleasant alterations of the original ‘values’ of the stone monuments. The removal of stains is therefore required on the occasion of conservation treatments. The paper reports on the characterisation of copper corrosion products found on two, very different, monuments in Rome: ‘Fontana delle Tartarughe’ (by T. Landini, last quarter of the 16th century) and ‘Statua dello Studente’ (by A. Cataldi, 1920). To identify the speciation of copper compounds in their carbonate matrices, different techniques [X‐ray diffraction, X‐ray fluorescence, SEM/energy‐dispersive X‐ray spectroscopy (EDS), micro‐Raman and XPS] had to be employed. To further confirm the identification of the chemical species, SEM/EDS data were also processed by principal component analysis. Copyright © 2013 John Wiley & Sons, Ltd.     

咪唑啉衍生物在H_2S水溶液中的腐蚀抑制机理(英文)

使用失重法和电化学极化技术研究了咪唑啉衍生物在H2S水溶液中对碳钢腐蚀的抑制机理.结果表明:咪唑啉衍生物能有效抑制H2S的腐蚀,属于阴极型缓蚀剂.咪唑啉衍生物在金属表面上的吸附符合Langmuir等温吸附,温度越高,越有利于吸附.加入缓蚀剂后,降低了腐蚀反应的活化能和指前因子,而指前因子是腐蚀反应的决定因素,因此缓蚀剂的加入能降低腐蚀速率.     

Fabrication and anti‐corrosion property of superhydrophobic hybrid film on copper surface and its formation mechanism

Compact and uniform superhydrophobic films were prepared on copper substrates using one‐step solution‐immersion process, and the appropriate preparation conditions were selected for mixed solutions. SEM shows that the hybrid film of 1‐dodecanethiol and tetradecanoic acid on copper substrate is more compact with the contact angle of 160°. The electrochemical impedance spectroscopy and polarization test demonstrate that the anti‐corrosion property of surface‐modified copper substrate is greatly improved, especially for the hybrid film. Moreover, the competitive adsorption process and adsorptive geometry of hybrid film were well explained based on the results of quantum chemistry calculations, SEM, and energy dispersive X‐ray analysis. Copyright © 2009 John Wiley & Sons, Ltd.     

Influence of inhibitor structure and metal/solution interface on the corrosion resistance of the protected metal

Seven systems of more than 60 compounds with possible inhibiting properties are investigated. Several methods are used: electrochemical, gravimetric, XPS, and SEM analyses. The inhibition efficiency Z is related to the chemical structure of inhibitors (sequences of compounds with regard to Z are found), their electronic structure, the surface area of the inhibiting molecule, and the structure and composition of the metal/solution interface (impedance, adsorption equilibrium parameters, etc.). The most efficient of the investigated inhibitors have Z = 94–99%. Conclusions are drawn which allow identification of compounds with prognosticated inhibiting action. Published in Russian in Elektrokhimiya, 2006, Vol. 42, No. 11, pp. 1352–1364. Based on the report delivered at the 8th International Frumkin Symposium “Kinetics of the Electrode Processes,” October 18–22, 2005, Moscow. The text was submitted by the authors in English.     

Corrosion Inhibition of Imidazoline Derivates with Benzene Rings on Mild Steel in CO2-Saturated Brine Solution

Corrosion inhibition of three imidazoline derivates with different numbers of benzene rings, namely 2-phenyl-1-ethylamino imidazoline(CI-1), 2-phenyl-1-ethylamino-1-methylbenzyl quaternary imidazoline(CI-12) and 2-phenyl-1-benzoyl ethylamino imidazoline(CI-13), on mild steel in CO₂-saturated brine solution was evaluated by mass-loss method and potentiodynamic polarization method. The results show that the three imidazoline derivates can inhibit CO₂ corrosion effectively with CI-12 ranking the highest. They mainly restrain the anodic dissolution and act as anodic-type inhibitors. The adsorptions of these derivates on the mild steel surface follow the Langmuir adsorption isothermal equation and belong to chemical adsorption.     

胡麻籽油咪唑啉类缓蚀剂的制备及其缓蚀性能

以胡麻籽油、羟乙基乙二胺为原料合成咪唑啉中间体,用苄基氯进行改性,得到阳离子咪唑啉衍生物。利用FT IR对合成产物进行了表征,用静态失重法、电化学极化曲线和FESEM对其缓蚀性能进行了评价,并考察了不同缓蚀剂浓度、腐蚀浸泡时间对缓蚀效果的影响,探讨了其在A30钢表面的吸附行为。结果表明,合成的缓蚀剂在盐酸体系中对A30钢有较好的缓蚀性能,在浓度为100mg/L时对低碳钢的缓蚀效率可达87%,并且其产物为阳离子型缓蚀剂,吸附满足Langmuir等温吸附方程。最后采用量子化学方法对其缓蚀剂的缓蚀机理进行了分析。     

咪唑啉衍生物在含CO_2的模拟深层气井水溶液中缓蚀机理(英文)

应用电化学弱极化法和原子力显微镜(AFM)研究了咪唑啉衍生物类缓蚀剂在模拟深层气井水溶液中对碳钢的二氧化碳腐蚀的抑制效果和缓蚀作用机理.结果表明,在不同的实验温度下,该缓蚀剂均具有较好的缓蚀性能,属于以抑制阳极为主的混合型缓蚀剂.该咪唑啉衍生物在碳钢表面上的吸附遵从Langm iur方程.计算了该腐蚀体系热力学参数(ΔH°、ΔG°和ΔS°)以及腐蚀反应的活化能(Ea)和指前因子(A),并解释了实验结果.     

几种天然植物提取物对酪氨酸酶活性的抑制作用

选择合适的溶剂体系,用维生素C(Vc)作为阳性对照物,采用分光光度法测定了不同浓度的茶多酚、丹皮酚及金银花叶子总黄酮提取物(乙酸乙酯相)对酪氨酸酶活性的抑制作用.结果表明:采用1%丙三醇和1%吐温-80(体积比1∶1)混合液作溶剂可显著增加丹皮酚和金银花叶子总黄酮提取物在水中的溶解度;茶多酚、丹皮酚、金银花叶子总黄酮提取物对酪氨酸酶的活性都有一定的抑制作用,其抑制作用从强到弱依次为Vc、Vc∶丹皮酚=1∶2(质量比)、Vc∶丹皮酚=1∶1(质量比)、茶多酚、茶多酚∶丹皮酚=2∶1(质量比)、丹皮酚、金银花叶子总黄酮提取物.     

A study of the enhanced oxidation of poly-N-vinylimidazole films on copper

The degradation of poly-N-vinylimidazole films on copper substrates was studied by Fourier transform infrared spectroscopy and x-ray photoelectron spectroscopy. Infrared measurements on samples heated at 300°C for 15 minutes revealed that the oxidation of the polymer was accelerated by the copper. X-ray photoelectron spectroscopy showed that a layer of copper oxide was formed on top of the oxidized film. Copper ions were also detected within the polymer layer. © 1996 John Wiley & Sons, Inc.     

Synthesis,surface activity,and corrosion inhibition of dentritic quaternary ammonium salt-type tetrameric surfactants

The dentritic quaternary ammonium salt-type tetrameric surfactant (4C₁₂tetraQ) was synthesized, and the molecular structure was confirmed by ¹H NMR and FTIR. The surface activity of 4C₁₂tetraQ was investigated by surface tension, and surface chemical parameters, such as critical micelle concentration (cmc), efficiency (pC₂₀), effectiveness (π_cmc), the surface tension value at cmc (γ_cmc), minimum surface area (A_min), maximum surface excess (Γ_max), and cmc/C₂₀ were obtained from the measurement results. The results show that the 4C₁₂tetraQ surfactant has higher surface activity than the traditional monomeric surfactants (dodecyl trimethyl ammonium bromide, DTAB). The Krafft points were taken as <0°C, indicating that the synthesized tetrameric surfactants had good water solubility. Free energies of micellization and adsorption show that 4C₁₂tetraQ display greater propensity to absorb at the interface than form micelle in the bulk of the aqueous solution, and that the two processes are spontaneous. The measurement results show that 4C₁₂tetraQ has good emulsification power and foam performance. The corrosion efficiency was evaluated with the loss weight method in 1?mol/L HCl solution, and the results show that the 4C₁₂tetraQ surfactant has good corrosion inhibition, and can be considered as a corrosion inhibitor.     

Inhibition of copper corrosion by arylazotriazoles in nitric acid solution

Summary A study has been made to investigate the effect of some azoheterocyclic dyes of the type 3-arylazo 1,2,4-triazole (AT) on the corrosion of copper exposed to 0.5M nitric acid solution at different temperatures and at differentAT concentrations. Using potentiodynamic polarization andTafel electrochemical methods, it can be shown thatAT compounds are good inhibitors of copper corrosion in HNO₃ solution. The kinetic and thermodynamic parameters of the inhibited system were determined. The high inhibition efficiency of these compounds may be due to the adsorption of the additive itself and/or the adsorption of the formed Cu(II)-AT complexes at the polarized electrode interface. Cathodic polarization measurements showed thatAT dyes are predominantly cationic inhibitors.

---

Hemmung der Korrosion von Kupfer in salpetersaurer Lösung durch Arylazotriazole

Zusammenfassung Der Effekt einiger azoheterocyclischer Farbstoffe des Typs 3-Arylazo-1,2,4-triazol (AT) auf die Korrosion von Kupfer in 0.5M Salpetersäure bei verschiedenen Temperaturen und unterschiedlichenAT-Konzentrationen wurde untersucht. Potentiodynamische Polarisation und elektrochemische Methoden nachTafel zeigen, daß Verbindungen vom TypAT gute Korrosionsinhibitoren für Kupfer gegenüber HNO₃ sind. Die kinetischen und thermodynamischen Parameter des inhibierten Systems wurden bestimmt. Die hohe inhibitorische Wirksamkeit der untersuchten Verbindungen kann auf die Adsorption des Additivs selbst oder auf jene des Cu(II)-AT-Komplexes an der polarisierten Elektrodenoberfläche zurückzuführen sein. Kathodenpolarisationsmessungen zeigen, daßAT-Farbstoffe vorwiegend kationische Inhibitoren sind.

     

一种氨烷基膦酸型水处理剂的合成及缓蚀阻垢性能的研究

介绍了一种氨烷基膦酸型水处理剂二甲基氨基甲叉二膦酸(DMAMDP)的合成方法,并进行了缓蚀阻垢性能的研究。结果表明,DMAMDP在阻碳酸钙、硫酸钙、磷酸钙和稳定锌等方面,以及缓蚀性能均优于常用有机膦酸水处理剂HEDP和ATMP。     

Construction and corrosion behaviors of a bilayer superhydrophobic film on copper substrate

A novel bilayer superhydrophobic film was constructed on Cu substrate by a simple multi‐step process. First, (3‐mercaptopropyl) trimethoxysilane (MPTMS) molecules were self‐assembled onto the pre‐etched Cu surface via covalent bonding followed by hydrolysis and condensation, then 1H, 1H, 2H, 2H‐perfluorodecyltrichlorosilane (PFDTS) were grafted onto the resultant hydroxyl terminated surface via the Si‐O‐Si bonding. The so‐prepared sample was defined as Cu‐MPTMS‐PFDTS. The structure and morphology of the samples were characterized by means of contact angle measurement, X‐ray photoelectron spectroscopy and scanning electron microscopy. The corrosion behaviors of the films were evaluated by Tafel plot and electrochemical impedance spectroscopy on an electrochemical work station. The results indicated that the bilayer superhydrophobic film possessed better corrosion protection as compared with the control samples. The superiority of the corrosion protection was mainly ascribed to the following two aspects: the superhydrophobicity and polysiloxane micro‐structures of the Cu‐MPTMS‐PFDTS. Copyright © 2012 John Wiley & Sons, Ltd.