Optimal synthesis of 2D phononic crystals for broadband frequency isolation

The spatial distribution of material phases within a periodic composite can be engineered to produce band gaps in its frequency spectrum. Applications for such composite materials include vibration and sound isolation. Previous research focused on utilizing topology optimization techniques to design two-dimensional (2D) periodic materials with a maximized band gap around a particular frequency or between two particular dispersion branches. While sizable band gaps can be realized, the possibility remains that the frequency bandwidth of the load that is to be isolated might exceed the size of the band gap. In this paper, genetic algorithms are used to design squared bi-material unit cells with a maximized sum of band-gap widths, with or without normalization relative to the central frequency of each band gap, over a prescribed total frequency range of interest. The optimized unit cells therefore exhibit broadband frequency isolation characteristics. The effects of the ratios of contrasting material properties are also studied. The designed cells are subsequently used, with varying levels of material damping, to form a finite vibration isolation structure, which is subjected to broadband loading conditions. Excellent isolation properties of the synthesized material are demonstrated for this structure.     

Dispersive elastodynamics of 1D banded materials and structures: analysis

The elastodynamics of 1D periodic materials and finite structures comprising these materials are studied with particular emphasis on correlating their frequency-dependent characteristics and on elucidating their pass-band and stop-band behaviors. Dispersion relations are derived for periodic materials and are employed in a novel manner for computing both pass-band and stop-band complex mode shapes. Through simulations of harmonically induced wave motion within a finite number of unit cells, conformity of the frequency band structure between infinite and finite periodic systems is shown. In particular, only one or two unit cells of a periodic material could be sufficient for “frequency bandedness” to carry over from the infinite periodic case, and only three to four unit cells are necessary for the decay in normalized transmission within a stop band to practically saturate with an increase in the number of cells. Dominant speeds in the scattered wave field within the same finite set of unit cells are observed to match those of phase and group velocities of the infinite periodic material within the most active pass band. Dynamic response due to impulse excitation also is shown to capture the infinite periodic material dynamical characteristics. Finally, steady-state vibration analyses are conducted on a finite fully periodic structure revealing a conformity in the natural frequency spread to the frequency band layout of the infinite periodic material. The steady-state forced response is observed to exhibit mode localization patterns that resemble those of the infinite periodic medium, and it is shown that the maximum localized response under stop-band conditions could be significantly less than in an equivalent homogenous structure and the converse is true for pass-band conditions.     

Ultrawide low frequency band gap of phononic crystal in nacreous composite material

The band structure of a nacreous composite material is studied by two proposed models, where an ultrawide low frequency band gap is observed. The first model (tension-shear chain model) with two phases including brick and mortar is investigated to describe the wave propagation in the nacreous composite material, and the dispersion relation is calculated by transfer matrix method and Bloch theorem. The results show that the frequency ranges of the pass bands are quite narrow, because a special tension-shear chain motion in the nacreous composite material is formed by some very slow modes. Furthermore, the second model (two-dimensional finite element model) is presented to investigate its band gap by a multi-level substructure scheme. Our findings will be of great value to the design and synthesis of vibration isolation materials in a wide and low frequency range. Finally, the transmission characteristics are calculated to verify the results.     

Flexural vibration band gaps in thin plates with two-dimensional binary locally resonant structures

The complete flexural vibration band gaps are studied in the thin plates with two-dimensional binary locally resonant structures, i.e. the composite plate consisting of soft rubber cylindrical inclusions periodically placed in a host material. Numerical simulations show that the low-frequency gaps of flexural wave exist in the thin plates. The width of the first gap decreases monotonically as the matrix density increases. The frequency response of the finite periodic thin plates is simulated by the finite element method, which provides attenuations of over 20dB in the frequency range of the band gaps. The findings will be significant in the application of phononic crystals.     

基于Timoshenko梁模型的周期充液管路弯曲振动带隙特性和传输特性

充液管路的固液耦合振动广泛存在于各种工程领域中,对其弯曲振动控制进行研究具有重要意义.将声子晶体的周期性思想引入到管路结构设计中,将管壁设计成沿轴向交替排列的周期性复合结构.基于Timoshenko梁模型,采用传递矩阵法计算了固液耦合条件下周期管路结构的弯曲振动能带结构及其传输特性,同时分析了材料阻尼系数、周期和非周期支撑对带隙特性的影响.充液周期管路结构的弯曲振动带隙特性为管路的振动控制提供了一条新的技术途径. 关键词： 声子晶体 充液管路 振动带隙     

A new periodic structure composite material with quasi-phononic crystals

Phononic crystals (PCs) provide a new method for vibration insulation and noise reduction. PCs commonly have small bandgap width, and understanding how to expand this bandgap, including the ultra-low band gap, is crucial for applying PCs to vibration reduction in engineering structures. A new periodic structure composite material quasi-PCs is proposed and the high polymer concrete with quasi-PCs structure is conducted. Vibration measurements for the new periodic structure composite material demonstrate that quasi-PC behavior can open the ultra-low frequency band gap. The new periodic structure composite material can be used to reduce vibrations in engineering field.     

Propagation of acoustic waves in a fluid-filled pipe with periodic elastic Helmholtz resonators

Helmholtz resonators are widely used to reduce noise in a fluid-filled pipe system. It is a challenge to obtain lowfrequency and broadband attenuation with a small sized cavity. In this paper, the propagation of acoustic waves in a fluid-filled pipe system with periodic elastic Helmholtz resonators is studied theoretically. The resonance frequency and sound transmission loss of one unit are analyzed to validate the correctness of simplified acoustic impedance. The band structure of infinite periodic cells and sound transmission loss of finite periodic cells are calculated by the transfer matrix method and finite element software. The effects of several parameters on band gap and sound transmission loss are probed.Further, the negative bulk modulus of periodic cells with elastic Helmholtz resonators is analyzed. Numerical results show that the acoustic propagation properties in the periodic pipe, such as low frequency, broadband sound transmission, can be improved.     

LCR分流电路下压电声子晶体智能材料的带隙

将带有LCR分流电路的压电陶瓷片对贴在铝和环氧树脂组成的声子晶体结构中.使智能材料的机械振动与压电陶瓷的压电效应耦合起来,推导出机械振动在压电陶瓷片上的等效附加应力;使LCR分流电路中的电磁振荡效应和声子晶体的能带特性有机结合,计算了在分流电路作用下智能材料扭转和弯曲振动的带隙特性,研究了电阻、电感、电容元件的改变对压电声子晶体智能材料带隙的影响.研究结果表明:在合理尺寸下,随着分流电路中电阻值的增大,带隙的频率范围变宽,但衰减幅值有所降低;电感和电容值的增大都可以使带隙向低频移动,带隙的衰减幅值随着电感值的增大而升高,但随着电容值的增大而降低.从而给压电声子晶体智能材料减震降噪的控制提供了一种新思路.     

局域共振复合单元声子晶体结构的低频带隙特性研究

本文提出了一种新型局域共振复合单元声子晶体结构, 并结合有限元方法对结构的带隙机理及低频共振带隙特性进行了分析和研究. 共振带隙产生的频率位置由所对应的局域共振模态的固有频率决定, 并且带隙宽度与局域共振模态的品质因子及其与基体之间的耦合作用强度有关. 采用局域共振复合单元结构可以实现声子晶体的多重共振, 在低频范围能打开多条共振带隙, 但受到共振单元排列方式的的影响. 由于纵向和横向局域共振模态的简并, 复合单元结构能在200 Hz以下的低频范围打开超过60%宽度的共振带隙, 最低带隙频率低至18 Hz. 这为声子晶体结构获得低频、超低频带隙提供了一种有效的方法. 关键词： 局域共振 低频带隙 复合单元 声子晶体     

Designing broad phononic band gaps for in-plane modes

Phononic crystals are known as artificial materials that can manipulate the propagation of elastic waves, and one essential feature of phononic crystals is the existence of forbidden frequency range of traveling waves called band gaps. In this paper, we have proposed an easy way to design phononic crystals with large in-plane band gaps. We demonstrated that the gap between two arbitrarily appointed bands of in-plane mode can be formed by employing a certain number of solid or hollow circular rods embedded in a matrix material. Topology optimization has been applied to find the best material distributions within the primitive unit cell with maximal band gap width. Our results reveal that the centroids of optimized rods coincide with the point positions generated by Lloyd's algorithm, which deepens our understandings on the formation mechanism of phononic in-plane band gaps.     

周期薄壁开口梁中的双耦合振动带隙

本文研究了由两种材料组合构成的周期性薄壁开口梁的弯曲和扭转双耦合振动。基于双耦合振动方程，给出了平面波展开法。当填充比不变时，晶格常数是影响带隙相对宽带的一个因素；当晶格常数和填充比不变时，杨氏模量是影响带隙宽带的主要因素，而不是密度。利用有限元法计算了有限周期结构的振动频率响应，在带隙频率范围内，振动衰减40dB左右。这些发现对于声子晶体的应用具有重要意义。     

Design and optimization of periodic structure mechanical filter in suppression of foundation resonances

The paper describes the development of periodic structure mechanical filter (PSMF) that has the potential to reduce vibration transmission and sound radiation at resonances of the foundation in a two-degree-of-freedom (2dof) vibration isolation system by using the band gaps of the periodic structure. The transmission matrix method is used to model vibration transmission of the 2dof system and an analytical expression of sound radiation from the foundation plate is derived. The multi-layer PSMF composed of rigid plates and curved beams is represented by an equivalent m-k-c (viscous damping) model. The propagation/attenuation zones and attenuation ability of PSMF are expressed in the propagation scenario and the iso-attenuation curves by exploiting the unit cell transfer matrix invariant. Influence of the number of unit cells, viscous damping on the mobility of PSMF and vibro-acoustic behavior of the 2dof system is extensively studied. And under the constraints of installation space and stability of the whole system, the more the number of the unit cells, the better attenuation ability in the band gap can be obtained. The interaction between PSMF and the 2dof system is analyzed by the substructure method and contribution of frequency component from different substructures is identified by setting different level of damping for each substructure. Factors influencing the first mounting frequency of the 2dof system with PSMF are discussed and three styles of installing PSMF are studied. The performance of piecewise periodic PSMF and quasi-periodic PSMF is also studied in an attempt to eliminate new-born resonances by PSMF. An optimization scheme involving sensitivity analysis is applied to obtain the optimal values of m and k. And the optimization is effective. The experiment of detecting the band gap of PSMF and the comparative trial of a 2dof system with a flexible plate as the foundation with/without PSMF are carried out. Both numerical and experimental simulation results have demonstrated that by use of PSMF, the vibration transmission at resonances is reduced and the radiation of the foundation at resonances is suppressed.     

Vibration reduction by using the idea of phononic crystals in a pipe-conveying fluid

Flexural vibration in a pipe system conveying fluid is studied. The pipe is designed using the idea of the phononic crystals. Using the transfer matrix method, the complex band structure of the flexural wave is calculated to investigate the gap frequency range and the vibration reduction in band gap. Gaps with Bragg scattering mechanism and locally resonant mechanism can exist in a piping system with fluid loading. The effects of various parameters on the gaps are considered. The existence of flexural vibration gaps in a periodic pipe with fluid loading lends new insight into the vibration control of pipe system.     

Enhancement of phononic band gaps in ternary/binary structure

Based on the transfer matrix method (TMM) and Bloch theory, the interaction of elastic waves (normal incidence) with 1D phononic crystal had been studied. The transfer matrix method was obtained for both longitudinal and transverse waves by applying the continuity conditions between the consecutive unit cells. Dispersion relations are calculated and plotted for both binary and ternary structures. Also we have investigated the corresponding effects on the band gaps values for the two types of phononic crystals. Furthermore, it can be observed that the complete band gaps are located in the common frequency stop-band regions. Numerical simulations are performed to investigate the effect of different thickness ratios inside each unit cell on the band gap values, as well as unit cells thickness on the central band gap frequency. These phononic band gap materials can be used as a filter for elastic waves at different frequencies values.     

Theoretical and Experimental Investigation of Flexural Vibration Transfer Properties of High-Pressure Periodic Pipe

According to the theory of phononic crystals,the hydraulic pipeline is designed to be a periodic structure composed of steel pipes and hoses to suppress the vibration of the hydraulic system with band gaps.We present theoretical and experimental investigations into the flexural vibration transfer properties of a high-pressure periodic pipe with the force on the inner pipe wall by oil pressure taken into consideration.The results show that the vibration attenuation of periodic pipe decreases along with the elevation of working pressure for the hydraulic system,and the band gaps in low frequency ranges move towards high frequency ranges.The periodic pipe has good vibration attenuation performance in the frequency range below 1000 Hz and the vibration of the hydrauhc system is effectively suppressed.All the results are validated by experiment.The experimental results show a good agreement with the numerical calculations,thus the flexural vibration transfer properties of the highpressure periodic pipe can be precisely calculated by taking the Quid structure interaction between the pipe and oil into consideration.This study provides an effective way for the vibration control of the hydraulic system.     

Phononic gaps induced by inertial amplification in BCC and FCC lattices

In this study, infinite and finite periodic body centered cubic (BCC) and face centered cubic (FCC) lattices with and without inertial amplification mechanisms are investigated. These three-dimensional lattices are modeled with mass and spring elements that are parametrically varied to observe their effect on phononic gap (stop band) limits. When inertial amplification mechanisms are used in both of the infinite periodic lattices, wide low frequency band gaps are generated. Moreover, wide and deep phononic gaps are obtained by using moderate amount of unit cells in the case of finite periodic lattices.     

X形超阻尼局域共振声子晶体梁弯曲振动带隙特性

以声子晶体理论为基础,设计了一种具有超阻尼特性的X形局域共振结构,分析了周期性附加X形局域共振的梁弯曲振动传播特性.利用拉格朗日方程分析了X形局域共振结构动力学等效特性,揭示了该结构的阻尼放大的机理,分析了几何结构参数对于带隙特性的影响,并利用有限元法验证了X形局域共振结构的超阻尼特性.研究结果表明,周期性附加X形局域结构能够有效地抑制低频弯曲振动在梁中的传播,产生超阻尼特性,实现低频、宽带的减振效果,为结构的低频减振提供了一个新的设计方案.     

An Analysis of Structural-Acoustic Coupling Band Gaps in a Fluid-Filled Periodic Pipe

A periodic pipe system composed of steel pipes and rubber hoses with the same inner radius is designed based on the theory of phononic crystals. Using the transfer matrix method, the band structure of the periodic pipe is calculated considering the structural-acoustic coupling. The results show that longitudinal vibration band gaps and acoustic band gaps can coexist in the fluid-filled periodic pipe. The formation of the band gap mechanism is further analyzed. The band gaps are validated by the sound transmission loss and vibration-frequency response functions calculated using the finite element method. The effect of the damp on the band gap is analyzed by calculating the complex band structure. The periodic pipe system can be used not only in the field of vibration reduction but also for noise elimination.     

一种多频局域共振型声子晶体板的低频带隙与减振特性

设计了一种多频局域共振型声子晶体板结构, 该结构由一薄板上附加周期性排列的多个双悬臂梁式子结构而构成. 由于多个双悬臂梁式子结构的低频振动与薄板振动的相互耦合作用, 这种局域共振型板结构可产生多个低频弯曲波带隙(禁带); 带隙频率范围内的板弯曲波会被禁止传播, 利用带隙可以实现对薄板的多个目标频率处低频减振. 本文针对这种局域共振型板结构进行了简化, 并基于平面波展开法建立了其弯曲波带隙计算理论模型; 基于该模型, 结合具体算例进行了带隙特性理论分析. 设计、制备了一种存在两个低频弯曲波带隙的局域共振型板结构样件, 通过激光扫描测振仪测试证实该结构存在两个低频带隙, 在带隙频率范围的板弯曲振动被显著衰减.     

Theoretical and experimental investigations of flexural wave propagation in periodic grid structures designed with the idea of phononic crystals

The propagation characteristics of flexural waves in periodic grid structures designed with the idea of phononic crystals are investigated by combining the Bloch theorem with the finite element method. This combined analysis yields phase constant surfaces, which predict the location and the extension of band gaps, as well as the directions and the regions of wave propagation at assigned frequencies. The predictions are validated by computation and experimental analysis of the harmonic responses of a finite structure with 11× 11 unit cells. The flexural wave is localized at the point of excitation in band gaps, while the directional behaviour occurs at particular frequencies in pass bands. These studies provide guidelines to designing periodic structures for vibration attenuation.