介孔氧化硅膜在多孔陶瓷载体上的组装

采用过滤成膜方式结合溶剂挥发诱导自组装方法在多孔氧化铝中空纤维上制备了介孔氧化硅膜。XRD、TEM和N₂吸附脱附实验结果显示非担载膜具有有序的六方介孔结构。通过对中空纤维担载膜的XRD分析进一步确认介孔氧化硅膜的形成。SEM和EDS线扫描结果显示制备的担载膜表面完整、无缺陷,膜层和载体界面之间结合紧密。在此基础上对介孔膜在多孔陶瓷载体上的形成机理进行了探讨。     

Al2O3-ZrO2复合膜的制备与表征

以异丙醇铝和氧氯化锆为原料,用溶胶-凝胶法在Al₂O₃中空纤维上制备了Al₂O₃-ZrO₂复合膜。应用TG、DTA、XRD、SEM等测试手段对复合膜的热稳定性、结构、形貌进行了表征。结果表明复合膜的热稳定性比单一由氧化铝或氧化锆制成的膜有显著的提高,在1100℃之前,复合膜以t-ZrO₂存在,1200℃时,出现了m-ZrO₂和α-Al₂O₃相。扫描电镜分析表明,膜表面完整、无缺陷。气体渗透实验进一步表明所得膜具有一定的气体选择性,0.3MPa和0.5MPa下对氮气和氩气的分离因子α分别为1.191和1.185,和氮气与氩气的理论分离因子(α=1.194)相当,说明气体通过膜的扩散以Knudsen扩散传质为主。用等温氮气吸附实验测定了非担载膜的孔径大小和分布,最可几孔径约为4.3nm。     

疏水介孔二氧化硅膜的制备与表征

用甲基三乙氧基硅烷(MTES)代替部分正硅酸乙酯(TEOS)作为前驱体，以聚乙烯醚-聚丙烯醚-聚乙烯醚三嵌段共聚物(P123)作有机模板剂，通过共水解缩聚反应制备了甲基修饰的介孔SiO₂膜。利用N₂吸附、FTIR、²⁹Si MAS NMR以及接触角测量仪对膜的孔结构和疏水性进行了表征。结果表明，修饰后的膜材料具有良好的介孔结构，最可几孔径为4.65 nm，孔体积为0.69 cm³·g^-1，比表面积为938.4 m²·g^-1；同时疏水性明显提高，当n_MTES/n_TEOS达到1.0时，其对水的接触角达到109°± 1.1°。气体渗透实验表明气体通过膜孔的扩散由努森机制所控制。     

包覆ZrO2锂离子筛的制备及其在盐湖卤水中的吸附性能

采用水热法制备前驱体Li_1.6Mn_1.6O₄,用液相沉淀法在其表面包覆ZrO₂,再经酸洗转型为包覆ZrO₂的锂离子筛H_1.6Mn_1.6O₄。采用XRD、SEM、EDS和HRTEM对前驱体的结构、形貌和成分进行了表征。研究了ZrO₂包覆量和焙烧温度对锰溶损率和锂吸附容量的影响。结果表明：当ZrO₂包覆量为3%,焙烧温度为450℃时,在前驱体表面形成厚度约15 nm的ZrO₂包覆层,首次锰溶损率从3.14%下降到2.65%,锂离子筛在盐湖卤水中锂吸附容量保持为29.4 mg·g^-1。包覆ZrO₂的锂离子筛经过10次循环吸附-脱附,锰溶损率降低至0.34%,锂吸附容量保持为24.4 mg·g^-1,高于未包覆的锂离子筛（22.9 mg·g^-1）。包覆ZrO₂改善了锂离子筛的结构和吸附容量的循环稳定性。     

扫帚状氧化铈制备及其对Pt基阳极催化剂催化性能的影响

采用水热合成法,合成了比表面积为175 m²·g^-1,孔径在2~4nm范围内的扫帚状CeO₂。通过微波辅助乙二醇还原氯铂酸法制备了Pt-CeO₂/RGO催化剂,探究扫帚状CeO₂的添加对Pt基催化剂电催化性能的影响。利用X射线衍射仪（XRD）、扫描电镜（SEM）、N₂吸附-脱附、X射线光电子能谱（XPS）对所制备的CeO₂及催化剂进行表征。利用电化学工作站对催化剂进行电化学性能测试。结果表明,催化剂中CeO₂保持原有扫帚状,Pt纳米粒子均匀分布于石墨烯载体表面;当m_RGO∶m_CeO2=1∶2时,添加了扫帚状CeO₂的Pt-CeO₂/RGO催化剂的电催化性能最优,电化学活性表面积为102.83 m²·g^-1,对乙醇氧化的峰值电流密度为757.17 A·g^-1,1 000 s的稳态电流密度为108.17 A·g^-1,对乙醇催化氧化反应的电荷转移电阻最小,活化能最低。     

类球形正交LiMnO2的制备、微结构和电化学性能

以共沉淀法得到的类球形MnCO₃为前驱物，制备了类球形正交LiMnO₂(So-LiMnO₂)，采用XRD、SEM和N₂吸附技术对样品进行表征；与非球形正交LiMnO₂(No-LiMnO₂)进行了对比研究。结果表明：o-LiMnO₂的堆垛层错度、结晶状况、颗粒形貌和大小与前驱物的微结构密切相关；在80次电化学循环测试过程中，So-LiMnO₂经15次循环可达最大的放电容量152 mAh·g^-1，其容量衰减平均每次循环0.58 mAh·g^-1；而No-LiMnO₂要经过38次循环才能达到最大放电容量128 mAh·g^-1，容量衰减平均每次循环高达1.24 mAh·g^-1。TEM和EDS分析证明：由一次粒子团聚的类球形So-LiMnO₂能有效地抑制电解液对材料的腐蚀、减少Mn的溶解，从而提高了电化学循环能力。     

γ-AlOOH/Al2O3修饰硅藻土的制备与Cs+、Pb2+吸附性能

以结晶氯化铝(AlCl₃·6H₂O)作为铝源,十二烷基苯磺酸钠(SDBS)为模板剂,采用水热法在硅藻土盘上制备了束状纳米结构γ-AlOOH/Al₂O₃复合吸附剂。采用XRD、SEM、TEM、TG/DSC、N₂吸脱附等对样品进行了表征。研究了样品对¹³³Cs⁺及Pb²⁺的吸附能力。研究表明,样品γ-AlOOH/硅藻土、γ-Al₂O₃/硅藻土,对Cs⁺及Pb²⁺均具有良好的吸附性能,两者对Cs⁺的去除率分别为98.9%和99.6%;对Pb²⁺的最大吸附量分别为357.1、416.7 mg·g^-1。两种样品对Pb²⁺的吸附均符合Langmuir吸附模型。     

锌镍铝水滑石微球的制备及吸附性能

以Zn（NO₃）₂·6H₂O、Ni（NO₃）₂·6H₂O、Al（NO₃）₃·9H₂O和尿素为原料,采用一步水热法制备分散性良好的三元锌镍铝水滑石（ZnNiAl-LDHs）微球。通过X射线衍射（XRD）、傅里叶转换红外光谱（FTIR）、场发射扫描电镜（FESEM）、透射电镜（TEM）和氮气吸附-脱附等测试手段对样品的结构和形貌进行表征,并比较ZnNiAl-LDHs和ZnAl-LDHs对甲基橙（MO）的吸附性能。结果表明,ZnNiAl-LDHs是由纳米片组成、具有3D结构的微球,粒径为1~2.5 μm,比表面积为156 m²·g^-1,远大于ZnAl-LDHs的比表面积38 m²·g^-1;ZnNiAl-LDHs和ZnAl-LDHs对甲基橙的饱和吸附量分别为329.60和143.47 mg·g^-1,ZnNiAl-LDHs表现出更强的吸附能力,其吸附等温线和吸附动力学分别符合Langmuir等温线模型和准二级动力学模型。     

常温合成硫掺杂微孔碳及其二氧化碳的吸附性能

常温下以间苯三酚和3-甲醛苯并噻吩作为原料,一步法合成了含硫酚醛树脂。在氩气保护下碳化,成功制备出了硫掺杂多孔碳（S-PC）。并利用扫描电镜（SEM）、X射线光电子能谱（XPS）、X射线衍射（XRD）和氮气吸附-脱附仪对材料进行了形貌、结构和性能的表征。实验结果表明,所得样品具有较高比表面积和大量的微孔,经过调控,可以使制备的硫掺杂多孔碳的BET比表面积达到997 m²·g^-1,并使其微孔孔体积达到0.44 cm³·g^-1。得益于较高的比表面积以及其富含微孔的特性,当材料应用于二氧化碳吸附时,具有较高的CO₂吸附量,在273和298 K时分别高达5.13,3.22 mmol·g^-1,并具有良好的选择性。     

Mn4+掺杂Co3O4纳米纤维的静电纺丝法制备及其电化学性能

通过静电纺丝法制备Mn⁴⁺掺杂的Co₃O₄复合纳米纤维,利用XRD、XPS、BET、SEM和电化学工作站等对材料的结构、成分、形貌和电化学性能进行表征与测试。研究发现,通过Mn⁴⁺掺杂,Co₃O₄复合纳米纤维的电化学性能得到明显改善。当n_Co∶n_Mn=20∶2时,相应的复合纤维具有较大比表面积68 m²·g^-1,而且该样品呈现出清晰的氧化还原峰,在1 A·g^-1的电流密度下,放电比电容量为585 F·g^-1,这比纯Co₃O₄纳米纤维的416 F·g^-1,有显著提高;循环500圈电容保持率达到82.6%,而纯Co₃O₄纳米纤维则是76.4%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.