Synergistic Catalysis of SnO2/Reduced Graphene Oxide for VO2+/VO2+ and V2+/V3+ Redox Reactions

In spite of their low cost, high activity, and diversity, metal oxide catalysts have not been widely applied in vanadium redox reactions due to their poor conductivity and low surface area. Herein, SnO₂/reduced graphene oxide (SnO₂/rGO) composite was prepared by a sol–gel method followed by high-temperature carbonization. SnO₂/rGO shows better electrochemical catalysis for both redox reactions of VO²⁺/VO₂⁺ and V²⁺/V³⁺ couples as compared to SnO₂ and graphene oxide. This is attributed to the fact that reduced graphene oxide is employed as carbon support featuring excellent conductivity and a large surface area, which offers fast electron transfer and a large reaction place towards vanadium redox reaction. Moreover, SnO₂ has excellent electrochemical activity and wettability, which also boost the electrochemical kinetics of redox reaction. In brief, the electrochemical properties for vanadium redox reactions are boosted in terms of diffusion, charge transfer, and electron transport processes systematically. Next, SnO₂/rGO can increase the energy storage performance of cells, including higher discharge electrolyte utilization and lower electrochemical polarization. At 150 mA cm⁻², the energy efficiency of a modified cell is 69.8%, which is increased by 5.7% compared with a pristine one. This work provides a promising method to develop composite catalysts of carbon materials and metal oxide for vanadium redox reactions.     

Electrochemistry at chemically assembled single-wall carbon nanotube arrays

Single-wall carbon nanotubes (SWNTs) chemically assembled on gold substrates were employed as electrodes to investigate the charge transfer process between SWNTs and the underlying substrates. Cyclic voltammetry (CV) indicates that the assembled SWNTs allow electron communication between a gold electrode and the redox couple in solution, though the SWNTs are linked directly onto the insulating monolayer of 11-amino-n-undecanethiol (AUT) on the Au substrate. An electron transfer (ET) mechanism, which contains an electron tunneling process across the AUT monolayer, is proposed to explain the CV behavior of Au/AUT/SWNT electrodes. Electrochemical measurements show that the apparent electron tunneling resistance, which depends on the surface density of assembled SWNTs, has apparent effects similar to those of solution resistance on CV behavior . The theory of solution resistance is used to describe the apparent tunneling resistance. The experimental results of the dependence of ET parameter psi on the potential scan rate upsilon are in good agreement with the theoretical predictions. Kinetic studies of the chemical assembly of SWNTs by atomic force microscopic (AFM), electrochemical, and Raman spectroscopic methods reveal that two distinct assembly kinetics exist: a relatively fast step that is dominated by the surface reaction, and a successive slow step that is governed by bundle formation.     

Inherent Electrochemistry and Activation of Chemically Modified Graphenes for Electrochemical Applications

Graphene research is currently at the frontier of electrochemistry. Many different graphene‐based materials are employed by electrochemists as electrodes in sensing and in energy‐storage devices. Because the methods for their preparation are inherently different, graphene materials are expected to exhibit different electrochemical behaviors depending on the functionalities and density of defects present. Electrochemical treatment of these “chemically modified graphenes” (CMGs) represents an easy approach to alter surface functionalities and consequently tune the electrochemical performance. Herein, we report a preliminary electrochemical characterization of four common chemically modified graphenes, namely: graphene oxide, graphite oxide, chemically reduced graphene oxide, and thermally reduced graphene oxide. These CMGs were compared with graphite as a reference material. Cyclic voltammetry was used to ascertain the chemical functionalities present and to understand the potential ranges in which the materials were electroactive. Electrochemical treatment with either an oxidative or a reductive fixed potential were then carried out to activate these chemically modified graphenes. The effects of such electrochemical treatments on their electrocatalytic properties were then investigated by cyclic voltammetry in the presence of well‐known redox probes, such as [Fe(CN)₆]^4?/3?, Fe^3+/2+, [Ru(NH₃)₆]^2+/3+, and ascorbic acid. Thermally reduced graphene oxide exhibited the best electrochemical behavior amongst all of the CMGs, with the fastest rate of heterogeneous electron transfer (HET) and the lowest overpotentials. These findings will have far‐reaching consequences for the evaluation of different CMGs as electrode materials in electrochemical devices.     

Effect of electrode surface microstructure on electron transfer induced conformation changes in cytochrome c monitored by in situ UV and CD spectroelectrochemistry

Electrochemical redox processes of bovine heart cytochrome c were investigated by in situ UV-vis and CD spectroelectrochemistry at bare glassy carbon electrode (GCE) and single-wall carbon nanotubes (SWNTs) modified glassy carbon electrode (SWNTs/GCE) using a long optical path thin layer cell. The spectra obtained at GCE and SWNTs/GCE reflect electrode surface microstructure-dependent changes in protein conformation during redox transition. Potential-dependent conformational distribution curves of cytochrome c obtained by analysis of in situ circular dichroism (CD) spectra using singular value decomposition least square (SVDLS) method show that SWNTs can retain conformation of cytochrome c. Some parameters of the electrochemical reduction process, i.e. the product of electron transfer coefficient and number of electrons (alpha n = 0.3), apparent formal potential (E0' = 0.04 V), were obtained by double logarithmic analysis and standard heterogeneous electron transfer rate constant k0 was obtained by electrochemistry and double logarithmic analysis, respectively.     

Electron transfer in pristine and functionalised single-walled carbon nanotubes

Since their very first days, electron transfer has always played a special role in carbon nanotubes' life. In view of their structural and electronic uniqueness, carbon nanotubes have been proposed either as bulk electrode materials for sensing and biosensing in advanced electrochemical devices, or as molecular-sized electrodes for very fast electrode kinetics investigations. Alternatively, electron transfer has been used to probe the electronic properties of carbon nanotubes by either direct voltammetric inspection or coupling with spectroscopic techniques, ultimately allowing, in the case of true solutions of individual uncut single-walled carbon nanotubes (SWNTs), to single-out their redox potentials as a function of diameter. For their redox properties, as emerged from these studies, SWNTs represent unique building blocks for the construction of photofunctional nanosystems to be used in efficient light energy conversion devices.     

Remarkable support effect of SWNTs in Pt catalyst for methanol electrooxidation

Carbon nanotubes have been proposed as advanced metal catalyst support for electrocatalysis. In this work, different carbon support materials including single-walled carbon nanotubes (SWNTs), multi-walled carbon nanotubes (MWNTs) and XC-72 carbon black, were compared in terms of their electrochemical properties using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The SWNTs is found to exhibit the highest accessible surface area in electrochemical reactions and the lowest charge transfer resistance at the SWNTs/electrolytes. These carbon materials are then loaded with varying amount of Pt by the electrodeposition technique to prepare carbon supported Pt catalysts. Electrochemical measurements of methanol oxidation reveal that the SWNTs supported Pt catalyst exhibits the highest mass activity (mA/mg-Pt). In comparison with Pt-XC-72 and Pt-MWNTs, the remarkably enhanced electrocatalytic activity of the Pt-SWNTs maybe attributed to a higher dispersion and utilization of the Pt particles, which are directly related to the electrochemical characteristics of SWNTs. The high concentration of oxygen-containing functional groups, high accessible surface area, low charge transfer resistance at the carbon/electrolyte interfaces can be important for the Pt dispersing and strong metal-support interaction in the Pt-SWNTs catalyst.     

A Surface Grafting of Carbon Allotropes with in‐situ Generated 3‐aryl Diazonium Chlorides: Electrochemical Kinetic Studies

In this work three different carbon allotropes: multi‐walled carbon nanotubes (MWCNT), graphene and carbon nanohorns (CNH) were covalently bound with in‐situ generated 3‐diazonium aryl chlorides. These species were attached to the carbon surface using an electrochemically‐initiated radical coupling, similar to the Gomberg‐Bachman type reaction. An electrochemical grafting of the extended π‐systems at the carbon surface was performed in aqueous media in a simple 3‐electrode system and its kinetics was investigated by a modified Butler‐Volmer approach. The analysis of Hammett constants demonstrated a strong influence of the type of electron donating‐/withdrawing substituents on the reduction potential peak position and the peak current. Moderately or strong electron withdrawing groups like ‐carboxy or ‐nitro tend to shift reduction potential towards more positive values, which facilitates an electron uptake. The deposition time varies for different carbon allotropes and depends on the carbon graphitization and the surface area. The best surface coverage was obtained at 90–150 sec of the deposition. Although, the surface functionalities are less conductive than the carbon, the electrodes showed a low internal resistance and thus a high rate of electron transfer (high exchange current density and the electron transfer rate constant), with the most promising observed for carbon nanohorns. The best performing carbon revealed also superior mass transport of the redox active species toward the electrode surface, owing to their unique particle shapes and its very porous structure. The Tafel analysis complemented by an impedance spectroscopy allowed selecting the best carbon substrate for the functionalization with a 3‐aminobenzoic acid.     

Improved properties of positive electrolyte for a vanadium redox flow battery by adding taurine

Taurine was employed as an additive to improve the thermal stability and electrochemical performance of positive electrolyte for a vanadium redox flow battery. The addition of taurine could significantly improve the thermal stability of positive electrolyte, and 2 M V(V) electrolyte with 4 mol% taurine could keep it stable at 40 °C for 120 h, which was 54 h longer than the pristine one. Electrochemical measurements showed that the electrolyte with taurine exhibited superior electrochemical activity and reaction kinetics with a larger diffusion coefficient, exchange current density and reaction rate constant compared with the pristine one. Moreover, the cell using taurine as additive achieved higher average energy efficiency (81.75%) than the pristine cell (79.15%). The Raman and XPS spectroscopy illustrated that taurine could combine with VO²⁺ to form a small molecule complex and the –NH₂ in taurine could be adsorbed on the surface of the electrode to provide more active sites for the electrode reaction, which led to the improvement of mass transfer and the charge transfer process for the V(IV)/V(V) redox reaction.     

Redox Mechanisms of Nodularin and Chemically Degraded Nodularin

The electrochemical behaviour of Nodularin (NOD), a hepatotoxic cyclic pentapeptide, was studied at a glassy carbon electrode. NOD electrochemical oxidation is an irreversible, pH‐independent process, involving the transfer of one electron. Upon incubation in different pH electrolytes, chemical degradation of NOD was electrochemically detected by the appearance of a new oxidation peak. The chemically degraded NOD (cdNOD), undergoes an irreversible, pH‐dependent oxidation, and its redox products are reversibly oxidised. The charge transfer properties of cdNOD as well as of its redox metabolites were investigated. Mechanisms for NOD oxidation, NOD chemical degradation and oxidation of cdNOD and its metabolites were proposed.     

Electrochemical and conductivity measurements of single-wall carbon nanotube network electrodes

The electrochemical response of two-dimensional networks of pristine single-wall carbon nanotubes (SWNTs) has been investigated. SWNTs were grown by catalyzed chemical vapor deposition on an insulating SiO2 substrate, and then electrically contacted by lithographically defined Au electrodes. Subsequent insulation of the contact electrodes enabled the electrochemical properties of the SWNT network to be isolated and directly studied for the first time. The electrochemical activity of the SWNT network was found to be strongly dependent on the applied potential. For the same SWNT electrode, the limiting current for the oxidation of 5 mM Fe(phen)32+ was found to be much greater than expected based on the signal for the reduction of 5 mM Ru(NH3)63+. Simultaneous conductance and electrochemical measurements demonstrated decreasing conductance as the potential was scanned negative (versus Ag/AgCl) with the minimum conductance at around the reduction potential for Ru(NH3)63+. These results are consistent with the presence of both metallic and semiconducting SWNTs in the SWNT network electrode. Moreover, these results show that through appropriate choice of mediator and electrode potential, metallic SWNTs can be electrochemically addressed independently of semiconducting SWNTs.     

Label-free and sequence-specific DNA detection down to a picomolar level with carbon nanotubes as support for probe DNA

This study describes a simple and label-free electrochemical impedance spectroscopic (EIS) method for sequence-specific detection of DNA by using single-walled carbon nanotubes (SWNTs) as the support for probe DNA. SWNTs are confined onto gold electrodes with mixed self-assembly monolayers of thioethanol and cysteamine. Single-stranded DNA (ssDNA) probe is anchored onto the SWNT support through covalent binding between carboxyl groups at the nanotubes and amino groups at 5′ ends of ssDNA. Hybridization of target DNA with the anchored probe DNA greatly increases the interfacial electron-transfer resistance (R_et) at the double-stranded DNA (dsDNA)-modified electrodes for the redox couple of Fe(CN)₆^3−/4−, which could be used for label-free and sequence-specific DNA detection. EIS results demonstrate that the utilization of SWNTs as the support for probe DNA substantially increases the surface loading of probe DNA onto electrode surface and thus remarkably lowers the detection limit for target DNA. Under the conditions employed here, R_et is linear with the concentration of target DNA within a concentration range from 1 to 10 pM with a detection limit down to 0.8 pM (S/N = 3). This study may offer a novel and label-free electrochemical approach to sensitive sequence-specific DNA detection.     

Amorphous Diamond-like Carbon Electrodes: The Catalytic Effect of Platinum Admixture

The kinetics of electrode reactions in the Fe(CN)^3-/4- ₆ redox system is studied on the platinum-doped (Pt content up to 15 at. %) amorphous diamond-like carbon thin-film electrodes. The wide-gap diamond-like carbon is electrochemically inactive per se; yet, it acquires the electrochemical activity on adding platinum to the film bulk during the film growth. The effect of platinum is of a threshold character; at the same time, with increasing platinum content, the electrode differential capacitance increases smoothly, and the resistivity of the material remains practically constant. The effect is explained with a model which assumes that both the conductance in the film bulk and the catalytic action of platinum on the charge transfer at the electrode/solution interface have a nonuniform character.     

A New Amperometric Hydrazine Sensor Based on Prussian Blue/Single‐walled Carbon Nanotube Nanocomposites

A slow reaction process has been successfully used to synthesize Prussian blue/single‐walled carbon nanotubes (PB/SWNTs) nanocomposites. Electrochemical and surface characterization by cyclic voltammetry (CV), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV‐vis absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy and X‐ray diffraction (XRD) confirmed the presence of PB nanocrystallites on SWNTs. PB/SWNTs modified glassy carbon electrode (GCE) exhibits efficient electron transfer ability and high electrochemical response towards hydrazine. The fabricated hydrazine sensor showed a wide linear range of 2.0×10^?6–6.0×10^?3 M with a response time less than 4 s and a detection limit of 0.5 μM. PB/SWNTs modified electrochemical sensors are promising candidates for cost‐effective in the hydrazine assays.     

Introducing hydrophilic carbon nanoparticles into hydrophilic sol-gel film electrodes

A hydrophilic carbon nanoparticle–sol-gel electrode with good electrical conductivity within the sol-gel matrix is prepared. Sulfonated carbon nanoparticles with high hydrophilicity and of 10–20 nm diameter (Emperor 2000) are co-deposited onto tin-doped indium oxide substrates employing a sol-gel technique. The resulting carbon nanoparticle-sol-gel composite electrodes are characterized as a function of composition and salt (KCl) additive. Scanning electron microscopy and voltammetry in the absence and in the presence of a solution redox system suggest that the composite electrode films can be made electrically conducting and highly porous to promote electron transport and transfer. The effect of the presence of hydrophilic carbon nanoparticles is explored for the following processes: (1) double layer charging, (2) diffusion and adsorption of the electrochemically reversible solution redox system 1,1′-ferrocenedimethanol, (3) electron transfer to the electrochemically irreversible redox system hydrogen peroxide, and (4) electron transfer to the redox liquid tert-butylferrocene deposited into the porous composite electrode film. The extended electrochemically active hydrophilic surface area is beneficial in particular for surface sensitive processes (1) and (3), and it provides an extended solid|organic liquid|aqueous solution boundary for reaction (4). The carbon nanoparticle–sol-gel composite electrodes are optimized to provide good electrical conductivity and to remain stable during electrochemical investigation.     

Redox processes in mesoporous oxide membranes: layered TiO2 phytate and TiO2 flavin adenine dinucleotide films

Thin films of TiO2 (anatase) nanoparticles are assembled at an electrode surface via a layer-by-layer deposition process employing phytic acid, pyromellitic acid, or flavin adenine dinucleotide (FAD) as molecular binders. With all three types of binders, layers of typically 30 nm thickness are formed each deposition cycle. FAD as an electrochemically active component immobilized at the surface of the TiO2 particles is reduced to FADH2 and reoxidized in a chemically reversible two electron-two proton redox process. Two distinct voltammetric signals are observed for the immobilized FAD redox system associated with (i) hopping of electrons at the TiO2 surface (reversible) and (ii) conduction of electrons through the TiO2 assembly (irreversible). The conduction of electrons through the TiO2 assembly is possible by diffusion over considerable distances as well as through a "spacer" layer of TiO2 phytate. An order of magnitude (upper limit) estimate for the diffusion coefficient of electrons through TiO2 phytate, D(electron) approximately 10(-6) m(2) s(-1), is obtained from voltammetric data. Finally, it is demonstrated that the calcination of TiO2 assemblies causes dramatic changes in the electron transfer kinetics for the immobilized FAD/FADH2 redox system.     

Insights into electrocatalytic activity of epitaxial graphene on SiC from cyclic voltammetry and ac impedance spectroscopy

Electrocatalytic activity of graphene grown epitaxially on SiC is studied using cyclic voltammetry and electrochemical impedance spectroscopy. AFM images show step-like topography of SiC-graphene. For ferri-/ferrocyanide redox couple, no voltammetric response is observed at the pristine graphene. Basal planes of graphite are electrochemically inactive as well. After electrochemical oxidation, apparent redox peaks appear at both the graphene and graphite electrode. However, more intensive redox peaks are observed at graphene, where simultaneous redox reaction with the adsorbed and the diffused ferri-/ferrocyanide ions occurs. Electrochemical impedance measurements show that the graphene electrode behaves like an array of microelectrodes. We used the partially blocked electrode model to fit impedance data. Using the fitting parameters, a size of microelectrodes was found to be 23.8?±?2.1 μm and the active surface of graphene was estimated to be 21 %. A value of the standard electron transfer rate constant found for the anodized epitaxial graphene (2.16?±?0.32)?×?10^??3cm???s^??1) is by one order of magnitude lower than the standard rate constant estimated for the anodized graphite basal planes (～5?×?10^??2cm???s^??1). Electrochemical reduction causes total disappearance of electrochemical responses at the graphene electrode, whereas only slight decrease of the peak currents is observed at the reduced graphene. Such behavior proves that different activation mechanisms occur at the graphene and graphite electrodes.     

氯过氧化物酶在碳纳米管修饰电极上的直接电化学研究

将氯过氧化物酶固定到单壁碳纳米管修饰玻碳电极,其循环伏安曲线出现一对准可逆氧化还原峰,说明碳纳米管能够很好地促进氯过氧化物酶在电极表面的直接电子传递.该过程与溶液pH值有关,可指认氯过氧化物酶在电极表面发生的是一电子一质子传递反应.该修饰电极制作简单,性能稳定,且对氧还原具有很好的电催化效应.     

Redox Couple of DNA on Multiwalled Carbon Nanotube Modified Electrode

It has been envisioned that carbon nanotubes could promote electron‐transfer reactions when used as electrode materials in electrochemical cells. In the present study, calf thymus DNA was electrochemically oxidized at an electrode modified with multiwalled carbon nanotubes. The potentials for DNA oxidation at pH 7.0 were found to be 0.71 and 0.81 V versus SCE, corresponding to the oxidation of guanine and adenine residues, respectively. An initial oxidation of adenine was observed in the first scan, which was followed by a quasi‐reversible redox process of the oxidation product in the subsequent scans.     

Microcystin-LR and chemically degraded microcystin-LR electrochemical oxidation

Microcystins (MCs) are cyclic hepatotoxic heptapeptides produced by certain strains of freshwater cyanobacteria toxic for humans and animals. The electrochemical behaviour of microcystin-LR (MC-LR) at a glassy carbon electrode (GCE) was investigated using cyclic voltammetry (CV), square wave voltammetry (SWV) and differential pulse voltammetry (DPV). The oxidation of MC-LR is a diffusion-controlled irreversible and pH-independent process that occurs with the transfer of only one electron and does not involve the formation of any electroactive oxidation product. Upon incubation in different pH electrolytes, homogeneous degradation of MC-LR in solution was electrochemically detected by the appearance of a new oxidation peak at a lower potential. The electrochemical behaviour of chemically degraded MC-LR is an irreversible, pH-dependent process, and involves the formation of two redox products that undergo reversible oxidation. The formation of degradation products of MC-LR was confirmed by HPLC with UV detection at room temperature. Experiments were also carried out in solutions containing constituent MC-LR amino acids, which enabled the understanding of the MC-LR electron transfer reaction and degradation. An oxidation mechanism for MC-LR is proposed.