Preparation of ethambutol-copper(II) complex and fabrication of PVC based membrane potentiometric sensor for copper

Copper(II) complex of ethambutol (I) was prepared and used in the fabrication of Cu(2+) selective ISE membrane. The membrane having Cu(II)-ethambutol complex (I) as electroactive material, along with sodium tetraphenylborate (NaTPB) as anion discriminator, dioctylphthalate (DOP) as plasticizer in poly(vinyl chloride) (PVC) matrix in the percentage ratio 6:2:190:200 (I:NaTPB:DOP:PVC) (w/w) gave a linear response in the concentration range 7.94x10(-6) to 1.0x10(-1) M of Cu(2+) with a slope of 29.9+/-0.2 mV per decade of activity and a fast response time of 11+/-2 s. The sensor works well in the pH range 2.1-6.3 and could be satisfactorily used in presence of 40% (v/v) methanol, ethanol and acetone and is selective for copper over a large number of cations with slight interference from Na(+) and Co(2+) if present at a level 1.5x10(-5) and 6.5x10(-5) M, respectively. It works well over a period of 6 months and can also be used as indicator electrode for the end point determination in the potentiometric titration of Cu(2+) against EDTA as well as in the determination of Cu(2+) in real samples.     

A PVC plasticized membrane sensor for nickel ions

A new PVC membrane sensor, which is highly selective towards Ni (II) ions, has been developed using a thiophene-derivative Schiff base as the ionophore. The best performance was exhibited by the membrane having the composition percentage ratio of 5:3:61:31 (ionophore:NaTPB:DBP:PVC) (w/w), where NaTPB is the anion excluder, sodium tetraphenylborate and DBP is the plasticizing agent (dibutyl phthalate). The membrane exhibited a good Nernstian response for nickel ions over the concentration range of 1.0 × 10⁻¹–5.0 × 10⁻⁶ M (limit of detection is 1.8 × 10⁻⁶ M) with a slope of 29.5 ± 1.0 mV per decade of activity. It has a fast response time of <20 s and can be used for a period of 4 months with good reproducibility. The sensor is suitable for use in aqueous solutions of a wide pH range of 3.2–7.9. The sensor shows high selectivity to nickel ions over a large number of mono-, bi- and trivalent cations. It has been successfully used as an indicator electrode in the potentiometric titration of nickel ions against EDTA and also for direct determination of nickel content in real samples – wastewater samples from electroplating industries and Indian chocolates.     

A PVC plasticized sensor for Ni(II) ion based on a simple ethylenediamine derivative.

A new PVC membrane ion selective electrode which is highly selective towards Ni(II) ions was constructed using a Schiff base containing a binaphthyl moiety as the ionophore. The sensor exhibited a good Nernstian response for nickel ions over the concentration range 1.0x10(-1)-5.0x10(-6) M with a lower limit of detection of 1.3x10(-6) M. It has a fast response time and can be used for a period of 4 months with a good reproducibility. The sensor is suitable for use in aqueous solutions in a wide pH range of 3.6-7.4 and works satisfactorily in the presence of 25% (v/v) methanol or ethanol. The sensor shows high selectivity to nickel ions over a wide variety of cations. It has been successfully used as an indicator electrode in the potentiometric titration of nickel ions against EDTA and also for the direct determination of nickel content in real samples: effluent samples, chocolates and hydrogenated oils.     

Fabrication of an iron(III)-selective PVC membrane sensor based on a bis-bidentate Schiff base ionophore

A Fe³⁺ ion-selective membrane sensor was fabricated from polyvinyl chloride (PVC) matrix membrane containing bis-bidentate Schiff base (BBS) as a neutral carrier, sodium tetraphenyl borate (NaTPB) as anionic excluder, and o-nitrophenyloctyl ether (NPOE) as a plasticizing solvent mediator. The effects of the membrane composition, pH, and additive anionic influence on the response properties were investigated. The best performance was obtained with a membrane containing 32% PVC, 62.5% NPOE, 3% BBS, and 2.5% NaTPB. The electrode shows a Nernstian behavior (slope of 19.3 ± 0.6) over a very wide iron ion concentration range (1.0 × 10⁻⁷–1.0 × 10⁻² M) and has a low detection limit (7.4 × 10⁻⁸ M). The potentiometric response of the sensor is independent of pH of the solution in the pH range 1.9–5.1. The proposed sensor has a very low response time (<15 s) and a good selectivity relative to a wide variety of other metal ions including common alkali, alkaline earth, heavy, and transition metal ions. The electrode can be used for at least 60 days without any considerable divergence in potentials. The proposed sensor was successfully applied as an indicator electrode for the potentiometric titration of 1.0 × 10⁻² M Fe³⁺ ions with a 1.0 × 10⁻⁴ M EDTA and the direct determination of Fe³⁺ in mineral water and wastewater samples.     

Manganese (II) selective PVC based membrane sensor using a Schiff base

N,N′,N″,N′′′-1,5,8,12-tetraazadodecane-bis(salicylaldiminato)(H₂L) has been used as ionophore for preparing Mn²⁺ selective sensor. Membranes of different composition with regard to ratio of H₂L:PVC:NPOE:NaTPB have been prepared and investigated. The best performance was obtained with the membrane of composition 10:150:150:10 (H₂L:PVC:NPOE:NaTPB) (w/w; mg). This membrane generated linear potential response in the concentration range of 5.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a Nernstian slope of 30.0 mV/decade of activity and fast response time (10 s). Hydrogen ion does not effect to the performance of sensor in the pH range 3.0-6.5. The sensor was found to be sufficient selective for Mn²⁺ over a number of alkali, alkaline and heavy metal ions and could therefore be used for the determination of manganese in various samples by direct potentiometry.     

PVC based 5,10,15,20-tetrakis (4-methoxyphenyl) porphyrinatocobalt(II) membrane potentiometric sensor for arsenite

PVC based membranes of 5,10,15,20-tetrakis(4-methoxyphenyl)porphyrinatocobalt(II) (TMOPP-Co) (I) as electroactive material with dibutyl butyl phosphonate (DBBP), dioctyl phthalate (DOP), 1-chloronaphthalene (CN), tri-n-butyl phosphate (TBP) and tris(2-ethylhexyl) phosphate (TEP) as plasticising solvent mediators have been prepared and tried for arsenite determination. The membrane having a composition 150:5:150 (PVC:I:DBBP) exhibited the best results with linear potential response in the concentration range of 7.9 × 10⁻⁵ to 1.0 × 10⁻¹ M of AsO₂⁻ with a slope of 28.8 mV/decade. The useful pH range of the sensor is 6.0-10.5. The membrane worked satisfactorily in non-aqueous medium up to 5% (v/v) non-aqueous content. The selectivity coefficient values for mono- and divalent anions indicate good selectivity for arsenite over a large number of anions.     

A lead (II) selective PVC membrane potentiometric sensor based on a tetraazamacrocyclic ligand

A polymeric membrane based Pb(II) selective potentiometric sensor was developed by using 1,3,7,9-tetraaza-2,8-dithia-4,10-dimethyl-6,12-diphenylcyclododeca-4,6,10,12-tetraene (TDDDCT) as an electroactive material along with anion excluder sodium tetraphenylborate (NaTPB) and plasticizer dioctylphthalate (DOP). The best performance in terms of slope, concentration range and response time was exhibited by the membrane having TDDDCT:PVC:DOP:NaTPB in the ratio 3:32:62:3 (w/w%). Potentiometric results show that the developed sensor works well in the concentration range 5.0 × 10^?7–1.0 × 10^?1 M with a near Nernstian slope of 29.5 (±0.5) mV decade^?1. The detection limit is down to 2.5 × 10^?7 M. The working pH range of this sensor is 2.8–7.0 and it works well in partially nonaqueous medium up to 25 % (v/v) methanol and ethanol. It exhibits a fast response time of 10 s. Selectivity coefficient values of various interfering ions were determined by the fixed interference method (FIM). The sensor reveals good selectivity for Pb(II) ions over other metal ions investigated. The developed sensor is used in the determination of lead in ‘Eveready battery waste’ and as an indicator electrode in the potentiometric titration of Pb(II) against EDTA.     

The effect of polymeric supports and methods of immobilization on the performance of an optical copper(II)-sensitive membrane based on the colourimetric reagent Zincon

A comparative study on the effect of different immobilization methods and matrix materials on the performance of copper(II)-sensitive membrane layers is presented. The indicator dye Zincon was immobilized in hydrophilic and hydrophobic polymers by various methods including: (a) physical entrapment of the Zincon-tetraoctylammonium ion pair in plasticized PVC, hydrogel, polystyrene, ethyl cellulose, poly-HEMA, AQ-polymer and in sol-gel glass; (b) electrostatic immobilization on an anion exchanger cellulose; and (c) covalent immobilization on cellulose via a sulfatoethylsulfonyl reactive group. The response to copper(II) ion was evaluated kinetically via the initial slope of the change in absorbance within 1 min. Layers made of hydrogel and PVC provide the highest sensitivity, while covalent immobilization is the most reproducible one, and sol-gel layers display the best mechanical stability.     

A new PVC matrix membrane sensor for determination of praseodymium(III) ion based on bis(salicylaldehyde)thiocarbohydrazone as an ion carrier

The sufficient amounts of bis(salicylaldehyde) thiocarbohydrazone (STCH) as a lipophilic selective element (3%, w/w), sodium nitrobenzene (NB) as a plasticizer (64%, w/w), tetraphenyl borate (NaTPB) as an anionic additive (3%, w/w), and poly vinyl chloride (PVC) as a polymeric matrix (30%, w/w) was employed to form a PVC membrane of a new Pr³⁺ ions selective sensor to apply as an indicator electrode in analytical applications. The best electrode response was observed in the slope (19.5 ± 0.7 mV per decade) over a wide concentrations from lower (1.0 × 10^?6 mol L^–1) to higher (1.0 × 10^?2 mol L^–1) of Pr³⁺ ion solution with a detection limit of 8.5 × 10^–7 mol L^–1. This electrode showed the fast response time about 10 second for praseodymium ion concentration range of 1.0 × 10^–6 to 1.0 × 10^–2 mol L^–1, in the pH range of 2.3–7.9. The matched potential method was applied to study the selectivity of electrode toward Pr³⁺ ions in comparison with many common cations. The results showed the negligible disturbance of all other cations on the proposed praseodymium(III) electrode. The making sensor has been employed successfully as an indicator electrode in the potentiometric titration of praseodymium(III) solution with EDTA at pH 6.0. Moreover the applicability of the sensor was studied in determination of Pr³⁺ ion in mixtures of different ions.     

An optical chemical sensor for mercury ion based on 2-mercaptopyrimidine in PVC membrane

An optical chemical sensor based on 2-mercaptopyrimidine (2-MP) in plasticized poly(vinyl chloride) (PVC) membrane incorporating (N,N-diethyl-5-(octadecanoylimino)-5H benzo[a]phenoxazine-9-amine (ETH 5294) and sodium tetraphenyl borate (NaTPB) for batch and flow-through determination of mercury ion is described. The response of the sensor is based on selective complexation of Hg²⁺ with 2-MP in the membrane phase, resulting in an ion exchange process between H⁺ in the membrane and Hg²⁺ in the sample solution. The influences of several experimental parameters, such as membrane composition, pH, and type and concentration of the regenerating reagent, were investigated. The sensor has a response range of 2.0 × 10⁻⁹ to 2.0 × 10⁻⁵ mol L⁻¹ Hg²⁺ with a detection limit of 4.0 × 10⁻¹⁰ mol L⁻¹ and a response time of ≤45 s at optimum pH of 6.5 with high measurement repeatability and sensor-to-sensor reproducibility. It shows high selectivity for Hg²⁺ over several transition metal ions, including Ag⁺, Cd²⁺, Co²⁺, Cr³⁺, Cu²⁺, Fe³⁺, Mn²⁺, Ni²⁺, and common alkali and alkaline earth ions such as Na⁺, K⁺, Mg²⁺, Ca²⁺, and Pb²⁺. The sensor membrane can be easily regenerated with dilute acid solutions. The sensor has been used for the determination of mercury ion concentration in water samples.     

PVC matrix membrane sensor for potentiometric determination of dodecylsulfate

The construction and performance characteristics of a new potentiometric PVC membrane sensor for the determination of sodium dodecyl sulfate (SDS) are described. The sensor was based on the use of an N-cetyl-N,N,N trimethyl ammonium (CTA) dodecyl sulfate (DS) ion pair as ion exchange sites in PVC matrix in the presence of o-nitrophenyl octylether as plasticiser. The sensor exhibited a fast, stable, and near-Nernstian response for SDS over the concentration range of 1 × 10^?3 to 10^?6 M at 25°C and the pH range 4–8.5 with anionic slope of 52.5 ± 0.5 mV decade^?1. The lower detection limit was 3 × 10^?6 M, and the response time was 25 s. Selectivity coefficients of SDS with respect to a number of different species were investigated. There were negligible interferences caused by most of the investigated anions. The determination of 1.0–280.0 µg mL^?1 of SDS in aqueous solutions showed an average recovery of 99.1%, and the mean relative standard deviation was 1.4 at 100 µg mL^?1. The results obtained in the determination of SDS in liquid soap, water and in some pharmaceutical preparations compared favourably with those obtained by the Methylene Blue active substance method (MBAS). In the present investigation, the DS sensor has been used as an end-point indicator electrode for some precipitation titration reactions, e.g. titration of SDS with CTMABr and cetylpyridinium chloride with SDS.     

Greener analytical method for the determination of copper(II) in wastewater by micro flow system with optical sensor

Greener analytical method using micro flow system for the determination of Cu(II) in wastewater samples was designed and investigated. The micro flow system consisted of a planar glass chip with poly(dimethylsiloxane) (PDMS) top plate and fixed with fiber optic probe as optical sensor for monitoring of Cu(II) that reacted with 2-carboxy-2′-hydroxy-5′-sulfoformazyl benzene (zincon) on the chip at 605 nm. This design gave a satisfied sensitivity with a linear calibration graph over the range of 0.1-3.0 μg mL⁻¹ of Cu(II) and correlation coefficient 0.9991. The percentage relative standard deviation was 2.5 for 10-replicate measurements and the limit of detection (LOD) was 0.1 μg mL⁻¹. This system has been successfully applied to the determination of Cu(II) in wastewaters from electroplating industry with less reagents and samples consumption and diminutive waste generation.     

PVC matrix membrane electrodes based on cobalt and nickel phenanthroline complexes for selective determination of cobalt(II) and nickel(II) ions

Potentiometric sensors for determining cobalt and nickel ions are described. They are based on the use of cobalt and nickel tris(1,10-phenanthroline)-TPB as electroactive compounds dispersed in plasticized poly(vinyl chloride) matrix. The sensors exhibit fast, near-Nernstian responses for cobalt and nickel-phenanthroline cations over the pH range 3–11 with a slope of 30.3 ± 0.3 mV/concentration decade. In the presence of excess 1,10-phenanthroline reagent, cobalt(II) and nickel(II) ions at concentration levels as low as 4 × 10^–6 M are accurately determined. The results show an average metal ion recovery of 98.5% with a mean standard deviation of 0.5%. Cobalt in organometallic compounds and nickel in silicate rocks are determined by these sensors and results agreeing fairly well with atomic absorption spectrometry are obtained.     

Optical pH sensor based on Calcon immobilization membrane

An optical pH sensor was developed by immobilizing Calcon on a porous cellulosic polymer film. The color of the membrane in acidic to basic medium changes from pink to blue, which can be used for determination of pH by spectrophotometry. The sensor response to the pH changes at two wavelengths 510 and 670 nm was investigated. The optical sensor can be used for repetitive and reversible pH measurement in the pH range of 4–9 with a response time of 5 min at 510 nm. The relative standard deviation (R.S.D) was less than 0.51% for seven times alternative measurements of pH from 7 to 8. The sensor was successfully applied to the determination of pH in tap and waste water samples.     

Strontium(II) selective PVC membrane electrode based acetophenone semicarbazone (ACS) as an ionophore

A new PVC membrane based strontium(II) ion-selective electrode has been constructed using acetophenone semicarbazone as a neutral carrier. The sensor exhibits a Nerstian response for strontium(II) ion over a wide concentration range 1.0 × 10⁻²–1.0 × 10⁻⁷ M with the slope of 29.4 mV/per decade. The limit of detection was 2.7 × 10⁻⁸ M. It was relatively fast response time (<10 s for concentration ⩾1.0 × 10⁻³ and <15 s for concentration of ⩾1.0 × 10⁻⁶ M) and can be used for 8 months without any considerable divergence in potentials. The proposed sensor revealed relatively good selectivity and high sensitivity for strontium(II) over a mono, di, trivalent cation and can be used in a pH range of 2.5–10.5. It was also successfully used as an indicator electrode in potentiometer titration and in the analysis of concentration in various real samples.     

Chelating ionophore based membrane sensors for copper(II) ions

Acetylacetone, ethylacetoacetate and salicyldehyde, are reported to form chelates with copper of high stability as compared to other metals. Therefore, PVC based membranes of bis[acetylacetonato] Cu(II) (A), bis[ethylacetoacetate] Cu(II) (B) and bis[salicyldehyde] Cu(II) (C) have been investigated as copper(II) selective sensors. The addition of sodium tetraphenylborate and various plasticizers, viz., DOS, TEHP, DOP, DBP and TBP have been found to substantially improve the performance of the sensors. The membranes of various compositions of the three chelates were investigated and it was found that the best performance was obtained for the membrane of composition A (1%): PVC (33%): TBP (65%): NaTPB (1%). The sensor shows a linear potential response to Cu(II) over wide concentration range 2.0 × 10⁻⁶ to 1.0 × 10⁻¹ M (detection limit 0.1 ppm) with Nernstian compliance (29.3 mV decade⁻¹ of activity) between pH 2.6 and 6.0 with a fast response time of 9 s. The potentiometric selectivity coefficient values as determined by match potential method (MPM) indicate excellent selectivity for Cu²⁺ ions over interfering cations. The sensor exhibits adequate shelf life (3 months) with good reproducibility (S.D. ±0.2 mV). The sensor has been used in the potentiometric titration of Cu²⁺ with EDTA. The utility of the sensor has been tested by determining copper in vegetable foliar and multivitamin capsule successfully.     

PVC matrix membrane sensor for potentiometric determination of cetylpyridinium chloride.

A novel cetylpyridinium chloride-selective membrane sensor consisting of cetylpyridinium-ferric thiocyanate ion pairs dispersed in a PVC matrix placticized with dioctylphthalate is described. The electrode shows a stable, near-Nernstian response for 1 x 10(-3)-1 x 10(-6) mol l-1 cetylpyridinium chloride (CPC) at 25 degrees C over the pH range 1-6 with a cationic slope of 57.5 +/- 0.4. The lower detection limit is 8 x 10(-7) mol l-1 and the response time is 30-60 s. Selectivity coefficients for CPC relative to a number of interfering substances were investigated. There is negligible interference from many cations, anions and pharmaceutical excipients; however, cetyltrimethylammonim bromide (CTMAB) interfered significantly. The determination of 0.5-350 micrograms/ml of CPC in aqueous solutions shows an average recovery of 98.5% and a mean relative standard deviation of 1.6% at 56.0 micrograms/ml. The direct determination of CPC in Ezafluor mouthwash gave results that compare favorably with those obtained by the British Pharmacopoeia method. Precipitation titrations involving CPC as titrant are monitored with a CP sensor. The CP electrode has been utilized as an end point indicator electrode for the determination of anionic surfactants in some commercial detergents.     

Photocured thiol-ene based optical fluorescence sensor for determination of gold(III)

This study describes the preparation and the characterization of a new thiol-ene based polymeric fluorescence sensor by photo initiated polymerization of trimethylolpropane tris(3-mercaptopropionate), 2-hydroxyethylacrylate, and 2,4,6-triallyloxy-1,3,5-triazine which are used as monomers and also a photo initiator (2,2-dimethoxy-2-phenylacetophenone) for its usage as optical sensor for gold ions. The thiol-ene based polymeric membrane sensor was characterized by using attenuated total reflectance-fourier transform infrared spectroscopy (ATR-FTIR) and scanning electron microscopy (SEM). The response characteristics of the sensors including dynamic range, pH effect, response time, and the effect of foreign ions were investigated. Fluorescence spectra showed that the excitation/emission maxima of the membrane were at 379/425 nm, respectively     

Hydrogen chromate PVC matrix membrane sensor for potentiometric determination of chromium(III) and chromium(VI) ions

A novel potentiometric Cr(6+) PVC matrix membrane sensor incorporating nickel tris(1,10-bathophenanthroline) hydrogen chromate as an electroactive material and 2-nitrophenyl phenyl ether as solvent mediator is described. In a phosphate buffer solution of pH 5, the sensor displays a rapid and linear response for Cr(6-) over the concentration range 2 x 10(-2)-8 x 10(-6) M with an anionic slope of 55.5 +/- 0.2 mV decade(-1) and a detection limit of the order of 0.4 microg ml(-1). The sensor is used for sequential determination of Cr(6+) and Cr(3+) by direct monitoring of Cr(6+) followed by oxidation of Cr(3+) and measurement of the total chromium. The average recoveries of Cr(3+) and Cr(6+) at concentration levels of 0.5-50 microg ml(-1) are 98.1 +/- 0.4% and 99.1 +/- 0.4% respectively. Redox and precipitation titrations involving Cr(6+) as a titrant are monitored with the sensor. Cr(3+) and/or Cr(6+) in wastewaters of some industries (e.g., leather tanning, electroplating, aluminum painting) and the chromium contents of some alloys and refractory bricks are assessed. The results agree fairly well with data obtained using the standard diphenylcarbazide spectrophotometric method.     

PVC membrane based potentiometric sensors for uranium determination

Two novel uranyl PVC matrix membrane sensors responsive to uranyl ion are described. The first sensor incorporates tris(2-ethylhexyl)phosphate (TEHP) as both electroactive material and plasticizer and sodium tetraphenylborate (NaTPB) as an ion discriminator. The sensor displays a rapid and linear response for UO₂²⁺ ions over the concentration range 1×10⁻¹–2×10⁻⁵ mol l⁻¹ UO₂²⁺ with a cationic slope of 25.0±0.2 mV decade⁻¹. The working pH range is 2.8–3.6 and the life span is 4 weeks. The second sensor contains O-(1,2-dihydro-2-oxo-1-pyridyl)-N,N,N′,N′-bis(tetra-methylene)uronium hexafluorophosphate (TPTU) as a sensing material, sodium tetraphenylborate as an ion discriminator and dioctyl phenylphosphonate (DOPP) as a plasticizer. Linear and stable response for 1×10⁻¹–5×10⁻⁵ mol l⁻¹ UO₂²⁺ with near-Nernstian slope of 27.5±0.2 mV decade⁻¹ are obtained. The working pH range is 2.5–3.5 and the life span of the sensor is 6 weeks. Interference from many inorganic cations is negligible for both sensors. However, interference caused by some ions (e.g. Th⁴⁺, Cu²⁺, Fe³⁺) is eliminated by a prior ion exchange or solvent extraction step. Direct potentiometric determination of as little as 5 μg ml⁻¹ uranium in aqueous solutions shows an average recovery of 97.2±1.3%. Application for the determination of uranium at levels of 0.01–1 wt.% in naturally occurring and certified ores gives results with good correlation with data obtained by X-ray fluorescence.