Determination of the potassium content of explosive residues using miniaturised isotachophoresis

A new method has been developed to allow the determination of potassium in post-explosion residues to be made using miniaturised isotachophoresis. The method is based on the use of a caesium leading ion with 4.5 mM 18-crown-6 ether added to retard the potassium to allow reliable determinations to be made. With the conditions selected no interference was noted from other small inorganic cations, such as ammonium, barium, calcium, magnesium, sodium or strontium. The method was successfully applied to the analysis of seven samples containing explosive residues obtained from the unconfined burning of several flash powders. The procedure was found to offer good linearity for potassium determinations over the concentration range of 1.25-150 μg/mL with a coefficient of determination of 0.999 achieved.     

毛细管区带电泳技术快速分离检测爆炸残留物中的无机离子

利用间接紫外毛细管区带电泳方法完成了对爆炸残留物中7种无机离子(K+,NH+4,NO-2,NO-3,SO2-4,ClO-3,ClO-4)的分离检测。阳离子测定采用的缓冲体系为10 mmol/L吡啶（pH 4.5）-3 mmol/L冠醚,K+和NH+4在2.6 min内达到基线分离,检出限分别为0.25 mg/L和0.10 mg/L(S/N=3)。阴离子测定采用的缓冲体系为40 mmol/L硼酸-1.8 mmol/L重铬酸钾-2 mmol/L硼酸钠（pH 8.6）,氢氧化四甲铵为电渗流改性剂,5种阴离子在4.6 min内达到基线分离,检出限为0.10～1.85 mg/L。该方法已成功地应用于实际爆炸物样品种类的判定分析,取得了很好的结果。     

毛细管区带电泳技术快速分离检测爆炸残留物中的无机离子

利用间接紫外毛细管区带电泳方法完成了对爆炸残留物中7种无机离子(K+,NH+4,NO-2,NO-3,SO2-4,ClO-3,ClO-4)的分离检测。阳离子测定采用的缓冲体系为10 mmol/L吡啶（pH 4.5）-3 mmol/L冠醚,K+和NH+4在2.6 min内达到基线分离,检出限分别为0.25 mg/L和0.10 mg/L(S/N=3)。阴离子测定采用的缓冲体系为40 mmol/L硼酸-1.8 mmol/L重铬酸钾-2 mmol/L硼酸钠（pH 8.6）,氢氧化四甲铵为电渗流改性剂,5种阴离子在4.6 min内达到基线分离,检出限为0.10～1.85 mg/L。该方法已成功地应用于实际爆炸物样品种类的判定分析,取得了很好的结果。     

Determination of residual chlorine in greywater using o-tolidine

The determination of chlorine with o-tolidine in greywater has been studied, and a batch method and a sequential injection method have been proposed. It was found that the reaction of o-tolidine with chlorine was slower in a greywater matrix. Grey water samples must be filtered before analysis, or alternatively, a blank of sample must be measured. The samples are very unstable, and after 2 h of storage in dark conditions at 4 degrees C the chlorine concentration can diminish. The standard addition method, in some samples gave unsatisfactory results as a consequence of matrix effects. It was concluded that samples with a total organic carbon (TOC) higher than 60 mgCl(-1) can not be accurately analysed using these methods. However, samples with a TOC lower than 60 mgCl(-1) gave 100+/-3% recoveries. The linear range of the methods was 0-3.0 and 0-5.0 mgCl(2)l(-1), and the limit of quantification 0.2 and 0.5 mgCl(2)l(-1), for the batch method and the sequential injection method, respectively. This is the first paper devoted to grey water from the analytical chemistry point of view.     

Determination of inorganic selenium species by miniaturised isotachophoresis on a planar polymer chip

The use of miniaturised isotachophoresis to allow the simultaneous determination of two inorganic selenium species has been investigated using a poly(methyl methacrylate) chip with a 44-mm-long, 200-microm-wide, 300-microm-deep separation channel. The miniaturised device included an integrated on-column, dual-electrode conductivity detector and was used in conjunction with a hydrodynamic fluid transport system. A simple electrolyte system has been developed which allowed the separation of selenium(IV) and selenium(VI) species to be made in under 210 s. The limits of detection were calculated to be 0.52 mg L(-1) for selenium(IV) and 0.65 mg L(-1 )for selenium(VI). The method allowed the separation of the selenium species from a range of common anions including fluoride, nitrate, nitrite, phosphate, sulfate and sulfite.     

含氯橡胶制品中2-巯基咪唑啉的气相色谱法测定

建立了含氯橡胶制品中2-巯基咪唑啉的气相色谱分析方法.试样采用索氏提取,提取液经旋转蒸发浓缩、定容后,用Rtx-1701气相色谱毛细管柱分离,氢火焰离子化检测器(FID检测器)检测,外标法定量.2-巯基咪唑啉的平均回收率(n=7)为95.1％ ～100.6％,相对标准偏差(n=7)为4.4％ ～6.6％,检出限为1.0...     

Host-guest complexation in capillary isotachophoresis. II. Determination of aminophenol and diaminobenzene isomers in permanent hair colorants by using capillary isotachophoresis

The separation of 2-, 3- and 4-aminophenol and 1,2-, 1,3- and 1,4-diaminobenzene is studied by using capillary isotachophoresis. In order to obtain complete resolution of the six cations beta-cyclodextrin was used. The analytical method was used for the determination of aminophenol and diaminobenzene isomers in permanent hair colorant creams.     

Determination of heavy metals by isotachophoresis

The suitability of isotachophoresis for the analysis of metals in, e.g., environmental samples was studied. In a cationic operational system the heavy metals Fe, Cu, Ni, Cd, Co, Zn, Pb and Mn were simultaneously determined. The separation was achieved through complex formation with one of the counter ions, hydroxyisobutyric acid. The other counter ion was acetic acid, the leading ion was 0.02 M potassium or sodium (pH 4.1) and the terminator was H+. The analysis time was 15 min at 60 microA in a 0.2 mm I.D. capillary. Aqueous samples containing ppm and ppb amounts were enriched on a cation exchanger with an extremely low affinity for sodium (Chelex 100). Good recovery, linearity, precision and accuracy were obtained even down to the ppb range. Although the sensitivity of the method is not greater than that of some of the more established methods for the individual metals, a great advantage of isotachophoresis is the simultaneous determination of the metals, with equal response factors. An example is given of the determination of metals, including aluminium, in serum.     

Determination of potassium in sea-water by capillary isotachophoresis

Summary A new analytical procedure for the determination of potassium in sea-water was developed using capillary isotachophoresis and ion-exchange. After the sea-water sample was passed through the column packed with an ammonium form cation-exchange resin, sodium ion was removed with 2×10^–2 mol/l ammonium chloride solution and then potassium ion was eluted with 3×10^–1 mol/l ammonium chloride solution. Simultaneous determination of potassium and sodium ions was performed with a newly developed electrolyte system; the leading electrolyte was 5 mmol/l cesium hydroxide containing 2 mmol/l 18-crown-6, 0.01% hydroxypropyl methylcellulose (HPMC) and 70% methanol; the terminating electrolyte was 5 mmol/l tetrabutylammonium bromide containing 0.01% HPMC and 70% methanol. A large amount of ammonium in the eluate did not interfere with the isotachophoretic measurement of potassium and sodium ions. A linear working curve was obtained for artificial sea-water samples containing up to 700 mg/l potassium ion. The proposed method was applied to the determination of potassium in surface and bottom sea-water samples.

---

Kaliumbestimmung in Meereswasser durch Capillar-Isotachophorese

     

Determination of metoprolol tartrate by capillary isotachophoresis

This paper describes two isotachophoretic methods of metoprolol tartrate (MT) determination in pure and dosage forms. The first method was used for direct analysis where the following electrolyte system was applied: 10 mmol dm⁻³ 3-morpholino-2-hydroxypropanesulfonic acid, 10 mmol dm⁻³ NaCl, 2 % hydroxyethylocelulose as leading (LE) and 10 mmol dm⁻³ glycyl-glycine as terminating (TE) electrolytes. The second method was used for indirect analysis of MT as tartrate ions. In this case, the leading electrolyte consisted of 10 mmol dm⁻³ HCl, β-alanine (BALA), pH 4-5, and the terminating one of 5 mmol dm⁻³ glutamic acid, 10 mmol dm⁻³ β-alanine. Calibration curves were calculated as follows: for system A: y = (0.52 ± 0.05)x − (0.9 ± 0.2) (LOD = 13.0 mg dm⁻³, LOQ = 31.7 mg dm⁻³); and for system B: y = (0.240 +- 0.001)x + (0.18 ± 0.06) (LOD = 1.8 mg dm⁻³, LOQ = 4.4 mg dm⁻³). The isotachophoretic method was compared with the pharmacopoeial one by statistical tests.     

Determination of low chlorine concentrations in air using semiconductor chemical sensors

Comparative studies of electophysical gas-sensitive properties of semiconductor metal oxides (NiO, WO₃, and In₂O₃) in detecting trace concentrations of chlorine in air at 250–300°C were performed. WO₃ and In₂O₃ film sensors were found to have the best sensitivity, selectivity, and stability. However, WO₃ films are characterized by a longer relaxation time (3 min) compared to In₂O₃ films, for which it is no longer than 30 s. The kinetic and steady-state relative conductivity values of In₂O₃ films as functions of the chlorine concentration in air fall on the same curve in the range 0.01–0.7 ppm. This suggests that the concentration of chlorine in air can be determined from the initial rates of the variation of the relative conductivity of films, which significantly decreases the time of analysis (from 40 to 5 s at a sensor working temperature of 300°C). Changes in air humidity in the range from 40 to 80% have no effect on the initial rates of the variation of the relative conductivity of In₂O₃ films under kinetic conditions. The mechanism of the variation of In₂O₃ film conductivity in detecting chlorine in air was discussed.     

Determination of some antirheumatics by capillary isotachophoresis

Isotachophoresis (ITP) was applied for the determination of some antirheumatic drugs (fenoprofen, naproxen, ibuprofen, and ketoprofen) in human serum. The leading electrolyte contained hydrochloric acid (10 mmol x L(-1)), creatinine (pH 4.5) and methylhydroxyethyl cellulose (0.1%). The terminating electrolyte was 2-(N-morpholino)ethanesulfonic acid (10 mmol x L(-1)) adjusted with tris(hydroxymethyl)aminomethane to pH 6.9. The ITP separations were carried out in column-coupling configuration of the separation unit provided with a preseparation column of 160 x 0.8 mm inner diameter (ID) and analytical column of 160 x 0.3 mm ID. The limit of detection for ibuprofen, fenoprofen, and naproxen in serum by direct sampling was 0.008, 0.005 and 0.004 mmol x L(-1). The limit of detection for ketoprofen in serum after ethanol precipitation was 0.001 mmol x L(-1).     

Determination of paralytic shellfish toxins in dinoflagellate Alexandrium tamarense by using isotachophoresis/capillary electrophoresis

Baseline separation of seven paralytic shellfish toxins (PSTs), namely decarbamoylsaxitoxin (dcSTX), saxitoxin (STX), neosaxitoxin (NEO), gonyautoxin-2 (GTX-2), gonyautoxin-3 (GTX-3), gonyautoxin-1 (GTX-1), and gonyautoxin-4 (GTX-4), was achieved by using capillary ITP (CITP)/CE with UV detection. Separation parameters including duration time and voltage in CITP process, separation voltage, and pH and concentration of buffer were optimized. The developed method provided linear responses from 1.3 to 200 microM for the PSTs. The LOD ranged from 0.1 to 0.3 microM. PST extracts from two algal strains of Alexandrium tamarense were analyzed and the toxin concentrations in the samples were quantified with an internal standard method by using NEO as the internal standard. The algal extract of A. tamarense HK9301 contained 332 microM GTX-2 and 224 microM GTX-3, while the PSTs were not detected in the extract of A. tamarense CI01.     

Determination of chlorine species by capillary electrophoresis – mass spectrometry

The applicability of CZE with mass spectrometric detection for the determination of four chlorine species, namely chloride and three stable chlorine oxyanions, was studied. The main aspects of the proper selection of BGE and sheath liquid for the CE‐MS determinations of anions with high mobility were demonstrated, pointing out the importance of pH and the mobility of the anion in the BGE. The possibility of using uncoated fused silica capillary and common electrolytes for the separation was shown and the advantage of using extra pressure at the inlet capillary end was also presented. The linear range was found to be 1–100 µg/mL for ClO₃^? and ClO₄^?, 5–500 µg/mL for ClO₂^?, and 25–500 µg/mL for Cl^?, but the sensitivity can be greatly improved if larger sample volume is injected and electrostacking effect is utilized. The LOD for ClO₃^? in drinking water was 6 ng/mL, when very large sample volume was injected (10 000 mbar·s was applied).     

Determination of ammonium ion in sea-water by capillary isotachophoresis

A new procedure for determination of ammonium ion in sea-water by means of capillary isotachophoresis and a gas-liquid separator with a tubular microporous polytetrafluoroethylene membrane for preliminary enrichment has been developed. Ammonia generated by adding sodium hydroxide solution to the sea-water samples is allowed to permeate through the membrane and then dissolve in sulphuric acid. A linear calibration graph has been obtained with artificial sea-water samples containing up to 300 mug/1. ammonium ion. The method has been applied to the determination of ammonium ion in surface and bottom sea-water samples.