Comparative studies of eye-safe intracavity and extracavity optical parametric oscillators with an unstable telescopic cavity

We have experimentally studied the lasing characteristics of an eye-safe optical parametric oscillator (OPO) with an unstable telescopic cavity when it is placed inside (intracavity OPO) and outside (extracavity OPO) the plane-parallel cavity of a pulsed, nearly single-mode KGW:Nd pump laser. We used a KTP crystal as the nonlinear medium for the OPO. We have shown that the intracavity OPO has the higher lasing efficiency. We have observed that the distribution of nonlinear losses introduced by the intracavity OPO, nonuniform over the cavity cross section, leads to an increase in the diameter and divergence of the radiation beam from the pump laser and a dependence of its temporal lasing dynamics on the transverse beam coordinate. We propose a physical model qualitatively explaining the spatial and temporal lasing dynamics of a radiation source with an intracavity OPO. Both OPO versions generate beams of radiation with about the same divergence. When the KGW:Nd laser has an electrical pumping energy of 7.3 J and a cavity length of 77 cm, the intracavity OPO and the extracavity OPO emit pulses with energies of 14.5 mJ and 12.0 mJ and duration 18 nsec and 13 nsec respectively. The divergence of the eye-safe radiation (λ = 1.578 μm) at 86.5% of the total pulse energy is no greater than 5.5 mrad for an OPO output beam diameter of = 2 mm. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 73, No. 4, pp. 535–543, July–August, 2006.     

基于光参量振荡器的重频人眼安全激光器技术研究

 对KTP-OPO的相位匹配进行了理论分析和计算,并绘制了角度调谐曲线。基于光参量振荡器,选用KTP非线性晶体,在1.57μm人眼安全激光波段进行了实验研究。将脉冲氙灯侧面泵浦Nd∶YAG 1.064 μm激光应用于腔内KTP-OPO设计中,在工作频率5 Hz时,输出激光能量32 mJ,脉冲宽度7.22 ns,光 光转换效率为41%。这一结果使重频远距离人眼安全激光测距成为可能。     

High efficiency continuous-wave tunable signal output of an intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate

In this paper we report on a continuous-wave (CW) intracavity singly resonant optical parametric oscillator (ICSRO) based on periodically poled LiNbO₃ (PPLN) pumped by a diode-end-pumped CW Nd:YVO₄ laser. Considering the thermal lens effects and diffraction loss, an optical ballast lens and a near-concentric cavity are adopted for better operation. Through varying the grating period and the temperature, the tunable signal output from 1406~nm to 1513~nm is obtained. At a PPLN grating period of 29~μ m and a temperature of 413~K, a maximum signal output power of 820~mW at 1500~nm is achieved when the 808~nm pump power is 10.9~W, leading to an optical-to-optical conversion efficiency of 7.51%.     

Efficient continuous-wave eye-safe region signal output from intra-cavity singly resonant optical parametric oscillator

We report an efficient continuous-wave (CW) tunable intra-cavity singly resonant optical parametric oscillator based on the multi-period periodically poled lithium niobate and using a laser diode (LD) end-pumped CW 1064 nm Nd:YVO 4 laser as the pump source.A highly efficiency CW operation is realized through a careful cavity design for mode matching and thermal stability.The signal tuning range is 1401-1500 nm obtained by varying the domain period.The maximum output power of 2.2 W at 1500 nm is obtained with a 17.1 W 808 nm LD power and the corresponding conversion efficiency is 12.9%.     

Efficient continuous-wave eye-safe region signal output from intra-cavity singly resonant optical parametric oscillator

We report an efficient continuous-wave (CW) tunable intra-cavity singly resonant optical parametric oscillator based on the multi-period periodically poled lithium niobate and using a laser diode (LD) end-pumped CW 1064 nm Nd:YVO₄ laser as the pump source. A highly efficiency CW operation is realized through a careful cavity design for mode matching and thermal stability. The signal tuning range is 1401-1500 nm obtained by varying the domain period. The maximum output power of 2.2 W at 1500 nm is obtained with a 17.1 W 808 nm LD power and the corresponding conversion efficiency is 12.9%.     

近红外KTP单共振光参量振荡器

本文报道了角度调谐KTP单共振参量振荡器(SRO)的实验结果,并对结果进行了分析讨论.采用调QNd:YAG激光的二次谐波作为泵浦源.受腔镜涂膜带宽的限制,调谐范围为785～1010nm.最大的参量光脉冲能量为2.4mJ.最大的能量转换效率为26.3%.     

Continuous-wave mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate

This paper reports a continuous-wave （CW） mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate （PPLN） pumped by a diode-end-pumped CW Nd：YVO4 laser. Considering the thermal lens effects, it adopted an optical ballast lens and the near-concentric cavity for better operation. At the PPLN＇s grating period of 28.5 μm and the temperature of 140℃, the maximum idler output power of 155 mW at 3.86 μm has been achieved when the 808 nm pump power is 8.5 W, leading to an optical-to-optical conversion efficiency of 1.82%.     

Continuous-wave mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate

This paper reports a continuous-wave (CW) mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate (PPLN) pumped by a diode-end-pumped CW Nd:YVO$_{4}$ laser. Considering the thermal lens effects, it adopted an optical ballast lens and the near-concentric cavity for better operation. At the PPLN's grating period of 28.5\,$\mu$m and the temperature of 140\du, the maximum idler output power of 155\,mW at 3.86\,$\mu$m has been achieved when the 808\,nm pump power is 8.5\,W, leading to an optical-to-optical conversion efficiency of 1.82{\%}.     

高功率KTP晶体光参量振荡器热效应

采用有限元分析方法对KTP晶体内部3维温度分布情况进行了精确计算。根据参量过程满足的能量守恒条件和动量守恒条件,利用KTP晶体的热光色散方程计算了参量过程中温度对相位匹配角、光波走离角、允许角及晶体的有效非线性系数的影响。结果表明:晶体内温度分布不均匀;在沿着通光方向上晶体截面温度分布不同;加强晶体表面冷却效果,可有效降低温度对相位匹配角、光波走离角、允许角及晶体的有效非线性系数的影响。     

高功率,红光至中红外可调谐腔内和频光学参量振荡器

本文利用高重复频率,高平均功率大模场面积飞秒光纤激光器作为同步抽运源,抽运以多周期极化掺氧化镁铌酸锂为非线性晶体的单共振光学参量振荡器,获得了高功率可调谐红光至中红外光,信号光调谐范围为1450—2200 nm,闲频光调谐范围为2250—4000 nm,在2 W的抽运功率下,信号光输出波长为1502 nm时获得最大输出功率374 mW,转换效率为18.7%,脉冲宽度为144 fs,此时中红外输出中心波长为3.4μm,平均功率为166 mW.再利用BBO晶体对信号光进行腔内和频,获得和频光输出波长调谐范围为610—668 nm,在4.1 W抽运的情况下,最高平均功率为615 nm处的694 mW,转换效率达16.9%.     

Brewster-oriented passive Q-switch intracavity optical parametric oscillator

The behaviour of passively Q-switched solid-state lasers containing intracavity optical parametric oscillators (OPOs) is described, and a model to optimize this system‘s performance is developed. Meanwhile, an Nd:YAG laserpumped KTiOPO4 (KTP) intracavity OPO for eye safe laser output is studied experimentally. A Brewster-oriented bis-(4-dimethylaminodithiobenzil)-nickel (BDN) dye film is employed in laser cavity, which plays the double role of a passive Q-switch and a Brewster plate, to Q-switch the light to increase its intensity and polarize the light so that the polarization plane of fundamental irradiation is perpendicular to the Z-axis of KTP serving as the OPO nonlinear crystal, thereby providing type Ⅱ phase matching conditions to generate 1.572μm eye-safe signal laser. Eye-safe signal radiations of 6.6mJ per pulse at 1.572μm wavelength and pulse width as narrow as 6.0ns (FWHM) were obtained. Peak power was up to 1.1MW.     

Tunable femtosecond laser in the visible range with an intracavity frequency-doubled optical parametric oscillator

We demonstrated experimentally a synchronously pumped intracavity frequency-doubled femtosecond optical parametric oscillator (OPO) using a periodically-poled lithium niobate (PPLN) as the nonlinear material in combination with a lithium triborate (LBO) as the doubling crystal. A Kerr-lens-mode-locked (KLM) Ti:sapphire oscillator at the wavelength of 790 nm was used as the pump source, which was capable of generating pulses with a duration as short as 117 fs. A tunable femtosecond laser covering the 624-672 nm range was realized by conveniently adjusting the OPO cavity length. A maximum average output power of 260 mW in the visible range was obtained at the pump power of 2.2 W, with a typical pulse duration of 205 fs assuming a sech2 pulse profile.     

Fiber optical parametric oscillator based on photonic crystal fiber pumped with all-normal-dispersion mode-locked Yb:fiber laser

We demonstrate a cost effective, linearly tunable fiber optical parametric oscillator based on a home-made photonic crystal fiber pumped with a mode-locked ytterbium-doped fiber laser, providing linely tuning ranges from 1018 nm to 1038 nm for the idler wavelength and from 1097 nm to 1117 nm for the signal wavelength by tuning the pump wavelength and the cavity length. In order to obtain the desired fiber with a zero dispersion wavelength around 1060 rim, eight sam- ples of photonic crystal fibers with gradually changed structural parameters are fabricated for the reason that it is difficult to accurately customize the structural dimensions during fabrication. We verify the usability of the fabricated fiber experimen- tally via optical parametric generation and conclude a successful procedure of design, fabirication, and verification. A seed source of home-made all-normal-dispersion mode-locked ytterbium-doped fiber laser with 38.57 ps pulsewidth around the 1064 nm wavelength is used to pump the fiber optical parametric oscillator. The wide picosecond pulse pump laser enables a larger walk-off tolerance between the pump light and the oscillating light as well as a longer photonic crystal fiber of 20 m superior to the femtosecond pulse lasers, resulting in a larger parametric amplification and a lower threshold pump power of 15.8 dBm of the fiber optical parametric oscillator.     

Synchronously pumped femtosecond optical parametric oscillator at 1053 nm

A femtosecond optical parametric oscillator synchronously pumped by a Ti:Sapphire oscillator is reported. By the cavity length tuning, the signal wavelength is continuously tuned from 1000 to 1200 nm. The average output power of 32 mW is obtained at 1053 nm. The pulse width is measured to be 342 fs by intensity autocorrelation method. In addition, we observed bichromatic emission during the cavity length tuning process. Supported by the National High Technology Program Research and Development Program of China, the National Natural Science Foundation of China (Grant Nos. 60490280 and 10804128), and the National Basic Research Program of China (Grant No. 2007CB815104)     

连续波光参量振荡器定向红外干扰

介绍了基于光纤激光器泵浦的光学参量振荡器发展现状及其在定向红外干扰技术中的应用前景,对定向红外干扰技术的一些基本原理进行了讨论。利用自研的一台基于光纤激光器泵浦的连续波光学参量振荡器,通过周期调谐的方式分别实现3.414,3.630和3.820 m的瓦级中红外激光输出。采用这3个波长的激光对中红外热像仪进行了干扰原理性实验。对比实验结果可以得出:对于3.820 m波长的中红外激光,当其辐照的HgCdTe探测器前功率密度大于10 W/cm2量级时,在传输750 m距离后,热像仪实现饱和效果并且非饱和区域图像灰度级发生较大变化,达到了掩盖有用信号的目的。     

宽调谐高效率的BBO光参量振荡器

本文报道用354.7nm泵浦的单共振BBO脉冲光参量振荡器在413～661nm和2513～765nm波段内获得了可调谐的振荡输出,最高总能量转换效率达52％;文中还讨论了输出特性。     

Intracavity parametric conversion of radiation from a pulsed Nd:YVO<Subscript>4</Subscript> laser with high-power diode pumping

We have achieved intracavity parametric conversion of the radiation from a laser based on Nd:YVO₄ with high-power diode pumping. An LiF^2- crystal was used as the passive Q-switch for the Nd:YVO₄ laser. We have shown that by using an active element in the master laser with a passive region, we can form pulsed laser beams at a wavelength of 1.57 μm with peak power 3.2 kW and repetition rates up to 80 kHz, with beam quality parameter 1.4–1.8. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 73, No. 1, pp. 5–8, January–February, 2006.     

具有腔内光放大的单共振光参量振荡器

推导了描述稳态运行，具有腔内光放大的环形腔单共振光参量振荡器(ICOASRO)的功率特性的高斯光束理论.在这种结构的单共振光参量振荡器(SRO)中，适当地选择光放大器的参数，可以很大程度地降低单共振光参量振荡器的抽运阈值.在平均场近似下无二阶非线性交叉耦合作用的具有腔内光放大的环形腔单共振光参量振荡器的工作范围分成四个工作区域，且存在最小的单共振光参量振荡器的抽运阈值.文中的分析考虑了作为光放大器的激光增益介质的端面抽运特性，考虑了一般化单共振光参量振荡器的特性. 关键词： 单共振光参量振荡器 光放大 阈值     

高增益LiNbO3光参量振荡器

报道一台采用调Q红宝石激光器泵浦的高增益角度调谐LiNbO_3光参量振荡器.最大输出能量和转换效率分别高达50mJ/pulse和19%.该振荡器从1.1444μm到1.7652μm连续可调谐.     

1.2 W中红外ZnGeP2光参量振荡器

报导了利用Tm,HoGdVO4激光器抽运双谐振ZnGeP2光参量振荡器实验研究.Tm(5%),Ho(0.5%)GdVO4晶体采用液氮制冷方式,工作在77 K温度条件下.以25 W波长为800 nm的光纤耦合激光二极管抽运,2 μm激光最大平均功率7 W,脉冲宽度小于30 ns, 脉冲重复频率5 kHz到20 kHz可调.非线性频率转换晶体ZnGeP2长15 mm,55?切割,OPO谐振腔为平平腔,腔长约25 mm.在5W的2 μm激光抽运下,脉冲重复频率10 kHz,实现了信号光3.7 μm及闲频光4.5 μm中红外激光输出,参量光脉冲宽度为15～17 ns,最大平均功率大于1.2 W,光-光转换效率为20%.测量参量光输出光束全宽度远场发散角4 mrad,光束质量M2因子小于3.