表面活性剂增敏2.5次微分极谱测定香豆素

拟定了表面活性剂增敏、2 .5次微分极谱测定香豆素的方法。在含 6.0× 10 -6 mol·L-13 氯 2 羟丙基 三甲基氯化铵的 0 .1mol·L-1KH2 PO4 Na2 HPO4 (pH 6.8)缓冲液中 ,香豆素还原波 [峰电位Ep=- 1.60V(vs .SCE) ]的 2 .5次微分极谱峰峰电流e″p 与其浓度在 4 .0× 10 -7～ 6.0× 10 -5mol·L-1范围内呈良好线性关系 (r =0 .9998,n =10 ) ,检出限为 1.2× 10 -7mol·L-1。 13次平行测量 8.0× 10 -6 mol·L-1香豆素的峰电流 ,RSD为 1.5 %。该方法可用于中药白芷中香豆素的直接测定     

方波吸附溶出伏安法同时测定水中痕量铜和镉

报道了应用方波吸附溶出伏安法 (OSWSV)同时测定Cu(Ⅱ )和Cd(Ⅱ )。在 0 .0 1mol·L- 1酒石酸钾钠 2 .0× 10 - 4mol·L- 1水杨醛肟溶液中 (pH 11.75 ) ,Cu(Ⅱ )和Cd(Ⅱ )分别与水杨醛肟形成的络合物均产生非常灵敏的还原波 ,峰电位分别为 - 0 .5 5 6V和 - 0 .70 4V (vs.Ag/AgCl以下均同 )。峰电流与Cu(Ⅱ )、Cd(Ⅱ )浓度分别在 9.0× 10 - 74 .0× 10 - 8mol·L- 1和 2 .0× 10 - 6 6 .0×10 - 8mol·L- 1范围内呈线性关系 ,检出限均为 1.0× 10 - 8mol·L- 1。该法用于同时测定水样中痕量Cu(Ⅱ )和Cd(Ⅱ ) ,所得结果满意。通过对该体系的初步研究 ,Cu(Ⅱ )、Cd(Ⅱ )与水杨醛肟形成的络合物的还原峰具有明显的吸附性。     

胆红素的伏安特性及其微分脉冲伏安法测定

建立中成药中胆红素定量测定的微分脉冲伏安法。在多种介质中研究胆红素在玻碳电极上的电化学行为 ,全面优化条件后 ,采用标准加入法对中成药中胆红素进行测定 ,并通过与药典中标准方法对照和干扰实验及回收率实验对本方法进行评价。在 0 .2mol·L-1HAc NaAc 5 0 %EtOH和 1 1 5mol·L-1KH2 PO4 Na2 HPO4 溶液中 ,峰电流与胆红素浓度分别在 6.2 5× 1 0 -7～ 1 .0 0× 1 0 -5mol·L-1(r=0 .9976)和 5 .0 0× 1 0 -8～ 3.0 0× 1 0 -6mol·L-1(r=0 .9939)范围内呈良好的线性关系 ,检测下限分别为 5 .0× 1 0 -8mol·L-1和 5 .0× 1 0 -9mol·L-1。众生丸和牛黄解毒片中胆红素的质量分数分别为 0 .0 86%和 0 .1 0 9% ,RSD分别为 3 4%和 3.0 % ,回收率为 96.6%～ 1 0 4 .1 % ,其结果与药典中标准方法测定结果基本一致。     

单扫示波极谱法同时测定钴与镍

在 pH 9.70的Na2 CO3 NaHCO3、亚硝基红盐和氯代十四烷基吡啶体系中 ,镍和钴均有灵敏的络合物吸附波 ,其二阶导数峰电位分别为 - 0 .6 4V (vs .SCE) (镍 )和 - 0 .80V (vs .SCE)(钴 ) ,电流峰高与浓度在 3.4× 10 - 9～ 3.74× 10 - 6 mol·L- 1(镍 )和 7.0× 10 - 11～ 6 .0× 10 - 6 mol·L- 1(钴 )范围内呈线性关系 ,检出限分别为 2 .4× 10 - 9mol·L- 1(14 1ng·L- 1镍 )和 3.2× 10 - 11mol·L- 1(1.9ng·L- 1钴 )。方法应用于水样和生物样品中微量钴和镍的测定 ,结果满意     

线性扫描极谱法测定微量肉桂酸

在 1mol·L-1HOAc NaOAc介质中 (pH =3.6 ) ,肉桂酸有一还原峰 ,其峰电位为 - 1.4 7V(vs.SCE)。峰电流与肉桂酸浓度在 2 .0× 10 -5～ 8.0× 10 -4 mol·L-1之间呈线性关系 (r =0 .9989) ,检出限为 1.0× 10 -5mol·L-1。该法应用于肉桂酸含量的测定 ,结果满意 ,并对肉桂酸的电化学性质进行了研究     

单扫描极谱法测定注射液及血清中维生素K1

建立了维生素K1的极谱测定方法.在0.05 mol·L-1 NH4Cl-NH3(pH 8.58)缓冲溶液中,维生素K1可产生一极谱还原峰,峰电位Ep为-0.39 V ;其二阶微分峰峰电流ip″与维生素K1的浓度在1.1×10-7 ～2.2×10-5 mol·L-1范围内呈线性关系,相关系数r=0.998 6(n= 9 );方法的检出限为4.0×10-8 mol·L-1.13次平行测定2.2×10-5 mol·L-1维生素K1还原波二阶导数峰峰电流ip″的相对标准偏差(RSD)为1.83%.本法可直接用于注射液及血清中维生素K1含量的测定.     

流动注射安培法快速测定食盐中碘

报道了在酸性溶液中 ,IO- 3可被过量的I- 还原 ,FI流动注射安培法快速测定食盐中碘的方法。溶解于蒸馏水中的食盐样品 (30 μl)注入pH 1的 0 .1mol·L- 1NaCl + 1× 10 - 3mol·L- 1KI的载液中。自行研制的壁喷玻碳电极安培流通检测池作为工作电极 ,电位为 + 0 .2V(vs.SCE)。该系统和反向 (注入KI)系统的线性范围均为 1× 10 - 6 ～ 1× 10 - 4mol·L- 1,检出限为 5× 10 - 7mol·L- 1,相对标准偏差为 0 .8% (n =37) ,样品测定的回收率为 97.6 %～ 10 4 % ,采样频率 90样·h- 1。通过Bernoull恒流瓶可获得无脉冲载流。     

β-环糊精-二次微分简易示波伏安法测定苯巴比妥

在NaOH底液中 ,β 环糊精能够产生灵敏切口 ,且该切口深度随苯巴比妥 β 环糊精包结物量的增加而变浅。根据 β 环糊精的示波特性 ,建立了用二次微分简易示波伏安法间接测定苯巴比妥注射液中苯巴比妥含量的新方法。苯巴比妥的浓度在 2 .5× 10 - 6 ～ 4 .5× 10 - 5mol·L- 1范围内的回归方程为h(V) =4 .5 5 9- 1.381× 10 4 c(mol·L- 1) ,相关系数为 - 0 .9976 ,检出限为 1.5×10 - 6 mol·L- 1。对于 2 .5× 10 - 5mol·L- 1苯巴比妥 5次测定的相对标准偏差为 2 .7% ,回收率为10 2 .1%。与高效液相色谱和其他方法相比 ,此法具仪器简单、简便快速、无需通氮除氧等特点     

茜素紫修饰碳糊电极吸附阳极溶出伏安法测定痕量锑的研究

报道了采用茜素紫修饰碳糊电极测定痕量锑的阳极溶出伏安法。在 0 .0 3mol·L- 1邻苯二甲酸氢钾 盐酸缓冲溶液 (pH 2 .4 )中 ,通过开路富集 ,Sb(Ⅲ )与茜素紫形成络合物而富集于电极表面 ,然后交换介质至 0 .6mol·L- 1盐酸中 ,于 - 0 .6 0V还原后再进行阳极化扫描 ,于 - 0 .50V左右获得一灵敏的锑的溶出峰 ,二次导数峰电流与Sb(Ⅲ )的浓度在 4 .1× 10 - 9～ 2 .9× 10 - 7mol·L- 1范围内呈线性关系 ,检出限达 1.6× 10 - 9mol·L- 1。方法应用于水样中锑的测定 ,结果满意     

2-羟基-3-(三乙胺基)丙基十烷基硫醚修饰电极测定痕量金

研究了 2 羟基 3 (三乙胺基 )丙基十烷基硫醚 (HTPSD)修饰玻碳电极测定金的伏安特性及分析条件。在 0 .2mol·L- 1KCl HCl缓冲溶液中 (pH 1) ,金 (Ⅲ )被富集到电极表面 ,然后介质交换到 0 .2mol·L- 1KCl HCl空白溶液中 (pH 1)进行阴极溶出伏安测定 ,金 (Ⅲ )浓度在 2× 10 - 81× 10 - 6mol·L- 1范围内呈线性关系。检出限为 1× 10 - 8mol·L- 1。相对标准偏差小于 6 2 % ,一般常见离子不干扰。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.