26 nJ picosecond solitons from thulium-doped single-mode master oscillator power fiber amplifier

We report on an all single-mode master oscillator power fiber amplifier delivering high energy picosecond solitons at 1960 nm. The Bragg stabilized and self-starting oscillator delivers 62 pJ transform-limited pulses at 11.2 MHz pulse repetition frequency. Solitons are amplified in a core-pumped single-mode heavily thulium-doped fiber up to 26 nJ. The average and peak power are 291 mW and 7.4 kW, respectively. Pulses remain transform limited without significant self-phase-modulation distortion. We discuss the limitations of picosecond pulse amplification in a core-pumped single-mode fiber amplifier.     

基于光纤中超短脉冲非线性传输机理与特定光谱选择技术的多波长飞秒激光的产生

高集成、高可靠性宽调谐飞秒激光源在超快光谱学、量子光学及生物成像等研究与应用领域具有重要价值.如在生物多光子显微成像中,具有适中能量的宽调谐飞秒激光源不仅可满足多种生物组织荧光激发所需的峰值功率与激发波长,而且也可以显著提升非线性荧光产生效率、成像分辨率以及增大成像穿透深度.采用自主研发的高可靠性全保偏光纤飞秒激光器作为抽运源,基于低色散光纤中高峰值功率飞秒激光脉冲非线性传输引起的光谱加宽机制,本文开展了多波长全光纤飞秒激光产生技术研究.通过采用中心波长在980, 1000,1050, 1070与1100 nm的带通滤波片选择性地对单模光纤输出光谱中最左边与最右边光谱旁瓣进行滤波,在上述中心波长处分别可获得203, 195, 196, 187与194 fs的激光输出.本文提出的基于全光纤飞秒激光脉冲在单模光纤中非线性传输引起的光谱加宽机制与特定光谱选择技术的实验方案为高集成、高可靠性宽调谐飞秒激光源的实现提供了新的研究途径.     

高重复频率飞秒掺镱光纤放大器

 数值分析了掺镱单模光纤放大器的最佳增益光纤长度，并在实验上对掺镱单模光纤放大器和光栅对压缩器进行了研究。以最大平均输出功率为7 mW、重复频率为25.4 MHz、脉宽为56 ps的被动锁模环形腔掺镱光纤激光器作为种子脉冲，用250 mW的976 nm单模半导体激光器分别泵浦3种不同长度的掺镱单模光纤，对种子光进行放大，并用光栅对压缩器对放大后的脉冲在不同光栅距离上进行了压缩实验研究。当掺镱单模光纤长度为1.2 m时得到了较好的放大效果，种子脉冲被放大到140 mW，相应的增益为13 dB，放大后的单脉冲能量为5.5 nJ。在光栅距离为14.1 cm时获得了最短440 fs的脉冲，压缩后的功率为43 mW，相应的峰值功率为3.8 kW。     

1 MHz repetition rate hollow fiber pulse compression to sub-100-fs duration at 100 W average power

We report on nonlinear pulse compression at very high average power. A high-power fiber chirped pulse amplification system based on a novel large pitch photonic crystal fiber delivers 700 fs pulses with 200 μJ pulse energy at a 1 MHz repetition rate, resulting in 200 W of average power. Subsequent spectral broadening in a xenon-filled hollow-core fiber and pulse compression with chirped mirrors is employed for pulse shortening and peak power enhancement. For the first time, to our knowledge, more than 100 W of average power are transmitted through a noble-gas-filled hollow fiber. After pulse compression of 81 fs, 93 μJ pulses are obtained at a 1 MHz repetition rate.     

Ultrafast pulse sources based on multi-mode optical fibers

Ultrafast pulse sources based on multi-mode optical fibers are discussed. High-power passively mode-locked fiber lasers based on multi-mode rare-earth-doped optical fibers greatly exceed the power limitations of single-mode oscillators. Ultrafast multi-mode fiber amplifiers operating in conjunction with multi-mode oscillators provide even higher power levels, where nonlinear propagation effects enable pulse compression to below 100 fs. Multi-mode fiber oscillators can be combined with single-mode Raman-shifting fibers to produce widely wavelength-tunable sources of femtosecond pulses. Further amplification in Yb fibers allows for the generation of sub-100-fs pulses with W-level average powers.     

26 mJ, 130 W Q-switched fiber-laser system with near-diffraction-limited beam quality

We demonstrate a Q-switched fiber laser system emitting sub-60 ns pulses with 26 mJ pulse energy and near-diffraction-limited beam quality (M2<1.3). In combination with a repetition rate of 5 kHz, a corresponding average output power of 130 W is achieved. This record performance is enabled by a large-pitch fiber with a core diameter of 135 μm. This fiber allows for effective single-mode operation with mode field diameters larger than 90 μm even at average output powers exceeding 100 W.     

Supercontinuum generation in tapered fibers

Supercontinuum light with a spectrum more than two octaves broad (370-1545 nm at the 20-dB level) was generated in a standard telecommunications fiber by femtosecond pulses from an unamplified Ti:sapphire laser. The fiber had been tapered to a diameter of :2mum over a 90-mm length. The pulse energy was 3.9 nJ (average power, 300 mW). This source of high-intensity single-mode white light should find widespread applications in frequency metrology and spectroscopy, especially since no unconventional fibers are needed.     

Eye-safe, high-energy, single-mode all-fiber laser with widely tunable repetition rate

We present a novel high-energy, single-mode, all-fiber-based master-oscillator-power-amplifier （MOPA） laser system operating in the C-band with 3.3-ns pulses and a very widely tunable repetition rate, ranging from 30 kHz to 50 MHz. The laser with a maximum pulse energy of 25 μJ and a repetition rate of 30 kHz is obtained at a wavelength of 1548 nm by using a double-clad, single-mode, Er：Yb co-doped fiber power amolifier.     

66 W average power from a microjoule-class sub-100 fs fiber oscillator

Performance scaling of passively mode-locked ultrashort-pulse fiber oscillators in terms of average power, peak power, and pulse energy is demonstrated. A very-large-mode-area fiber laser in an all-positive group-velocity-dispersion ring cavity configuration with intracavity spectral filter, mode-locked by nonlinear polarization evolution, emits 66 W of average power at 76 MHz repetition rate, corresponding to 0.9 μJ pulse energy. The pulses are dechirped to 91 fs outside the cavity with an average power of 60 W remaining after the compressor. The generated pulse peak power is as high as 7 MW.     

Dual-stage soliton compression of a self-started additive pulse mode-locked erbium-doped fiber laser for 48 fs pulse generation

A dual-stage single-mode fiber (SMF) and large-effective-area fiber (LEAF) link for generating 48 fs pedestal-free pulses from a 40 MHz self-started additive pulse mode-locked erbium-doped fiber laser (APM-EDFL) with output peak power and pulse energy of 16 kW and 500 pJ, respectively, is demonstrated. With the SMF+LEAF link, a maximum pulse-width compression ratio of 7 and an optimized pulse-energy confining ratio of up to 85% can be achieved, and the soliton self-frequency shift effect of the APM-EDFL pulse can be greatly suppressed.     

Distortion-free delivery of nanojoule femtosecond pulses from a Ti:sapphire laser through a hollow-core photonic crystal fiber

We demonstrate propagation of femtosecond pulses in the 800-nm range through a hollow-core photonic crystal fiber with preserved temporal and spectral profiles for pulse energies up to 4.6 nJ. Without the use of a prechirping unit, 170-fs pulses were transmitted essentially undistorted at 812 nm, near the zero-dispersion wavelength. Because of the air guidance of pulses, intensity-dependent nonlinear effects were minimal, with only 15% pulse broadening occurring at 350-mW average output power. This fiber thus is excellently suited for applications that require single-mode delivery of high-energy ultrashort pulses to the fiber output face such as, for example, miniaturized multiphoton microscopes.     

自由耦合输出的大模场面积光子晶体光纤锁模激光器

对一种基于高增益掺Yb³⁺大模场面积光子晶体光纤（PCF）的锁模激光器进行了简化线型腔结构的实验和理论研究.实验中直接使用塌陷打磨为0°角的光纤端面作为一端腔镜,利用其端面反馈获得了激光振荡,并进一步利用半导体可饱和吸收镜（SESAM）和光栅对的滤波作用实现了稳定的锁模运转.通过调节滤波程度,使激光器实现了从宽带滤波锁模到窄带滤波锁模的连续可调谐.在宽带滤波锁模的条件下,得到了最大平均输出功率2.2 W,单脉冲能量29.3 nJ,脉冲宽度367 fs的锁模脉冲输出;在窄带滤波锁模的条 关键词： 飞秒激光 光纤激光器 光子晶体光纤 大模场面积光纤     

Sub-60-fs ytterbium-doped fiber laser with a fiber-based dispersion compensation

We present a mode-locked ytterbium fiber laser with a higher-order mode fiber compensating the group-velocity dispersion and partially the third-order dispersion of the single-mode fiber at a wavelength of 1 microm. The generated pulses had an energy of 0.5 nJ and could be dechirped externally to a pulse duration of less than 60 fs. The power spectrum shows a spectral full width at half-maximum of 57 nm.     

Ultrawide tunable Er soliton fiber laser amplified in Yb-doped fiber

A Raman-shifted and frequency-doubled high-power Er-fiber soliton laser for seeding an efficient high-power Yb fiber femtosecond amplifier is demonstrated. The Raman-shifted and frequency-doubled Er-soliton laser is tunable from 1.00 to 1.070microm and produces bandwidth-limited 24-pJ pulses at a repetition rate of 50 MHz with a FWHM pulse width of 170 fs at 1.040microm . The Yb(3+) amplifier has a slope efficiency of 52% and generates 3-ps linearly chirped pulses with an average power of 0.8 W at 1.05microm . After pulse compression, 74-fs bandwidth-limited pulses with an average power of 0.4 W and a pulse energy of 8 nJ are generated.     

220 μJ monolithic single-frequency Q-switched fiber laser at 2 μm by using highly Tm-doped germanate fibers

We report a unique all fiber-based single-frequency Q-switched laser in a monolithic master oscillator power amplifier configuration at ~1920 nm by using highly Tm-doped germanate fibers for the first time. The actively Q-switched fiber laser seed was achieved by using a piezo to press the fiber in the fiber Bragg grating cavity and modulate the fiber birefringence, enabling Q-switching with pulse width and repetition rate tunability. A single-mode polarization maintaining large core 25 μm highly Tm-doped germanate fiber was used in the power amplifier stage. For 80 ns pulses with 20 kHz repetition rate, we achieved 220 μJ pulse energy, which corresponds to a peak power of 2.75 kW with transform-limited linewidth.     

High-power all-normal-dispersion femtosecond pulse generation from a Yb-doped large-mode-area microstructure fiber laser

We report on an all-normal-dispersion mode-locked fiber laser based on a large-mode-area Yb-doped microstructure fiber and using a high nonlinear modulation depth semiconductor saturable absorber mirror. The laser delivers 3.3 W of average output power with positively chirped 5.5 ps pulses at a center wavelength of 1033 nm. The pulse repetition rate is 46.4 MHz, which results in an energy per pulse of 71 nJ. These pulses are extracavity dechirped down to 516 fs by using bulk gratings. The average power of the dechirped pulses is 2.3 W, which corresponds to a peak power of more than 96 kW.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Millijoule pulse energy high repetition rate femtosecond fiber chirped-pulse amplification system

We report on an ytterbium-doped fiber chirped-pulse amplification (CPA) system delivering millijoule level pulse energy at repetition rates above 100 kHz corresponding to an average power of more than 100 W. The compressed pulses are as short as 800 fs. As the main amplifier, an 80 microm core diameter short length photonic crystal fiber is employed, which allows the generation of pulse energies up to 1.45 mJ with a B-integral as low as 7 at a stretched pulse duration of 2 ns. A stretcher-compressor unit consisting of dielectric diffraction gratings is capable of handling the average power without beam and pulse quality distortions. To our knowledge, we present the highest pulse energy ever extracted from fiber based femtosecond laser systems, and a nearly 2 orders of magnitude higher repetition rate than in previously published millijoule-level fiber CPA systems.     

全光纤高功率被动锁模掺铥光纤激光器

利用非线性光环形镜(NOLM)的可饱和吸收特性实现了可自启动的2μm全光纤高能量被动锁模掺铥光纤激光器。当泵浦功率大于3W时,激光器工作在连续或不稳定脉冲运转状态;泵浦功率达到4.69W后,输出为自启动锁模脉冲,重复频率4.26MHz,中心波长2 061.5nm,光谱半极大宽度18.1nm,平均输出功率8.8mW;继续增加泵浦功率到最大值7.56W,可以得到中心波长2 062.2nm、光谱半极大宽度17.1nm、斜率效率为6.2%、脉冲宽度和能量分别为424fs和65.6nJ的稳定锁模脉冲。这是目前已报道的在未经放大情况下脉冲能量最高的2μm锁模脉冲光纤激光器。     

Supercontinuum generation employing the high-energy wave-breaking-free pulse in a compact all-fiber laser system

Supercontinuum (SC) generation is experimentally achieved in a compact all-fiber laser system by using high-energy wave-breaking-free dissipative soliton (DS) pulses. The pulses exhibit Gaussian (rectangular) shape profiles in spectral (temporal) domain, which is even reversed of the typical rectangular-spectrum DSs. With the increase of pump power the pulse duration enlarges dramatically whereas the bandwidth and peak power of the pulse keep almost constant, which enables the pulse to accumulate much higher energy during the pulse-shaping process. When inputting the amplified pulse into the single-mode fiber, SC with excellent flatness is generated with the spectral range from about 1550 to 1700 nm. Broader SC with the bandwidth of even larger than 1000 nm can also be generated by this kind of pulse in the near-zero-dispersion-flattened photonic-crystal fiber through strong nonlinear effects.