Cells studies on PEO/PEG/NaClO<Subscript>3</Subscript> thin-film electrolyte system based on composite V<Subscript>2</Subscript>O<Subscript>5</Subscript> electrode

The thin-film solid polymer electrolyte based on polyethylene oxide (PEO) with sodium chlorite (NaClO₃) has been prepared by a solution-cast technique. The electrolyte was characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry, alternating current conductivity, and Wagner’s polarization studies. The complexation of NaClO₃ with PEO was confirmed through the XRD and IR studies. The transference number measurement has shown that the ion transport is predominant over electrons in the polymer electrolytes (t _ions ≈ 0.94). The conductivity enhancement was observed in the case of the PEO/NaClO₃ system with the addition of plasticizers (low-molecular-weight polyethylene glycol, organic solvents propylene carbonate and dimethyl formamide. Cyclic voltammetry analysis showed the stability and redox character of the electrolyte and electrode. Finally, polymer electrolyte systems were examined by electrochemical cell studies using V₂O₅ and composite V₂O₅ cathode at temperature of 35 °C. Overall, the plasticized electrolyte shows a better electrochemical performance, and a higher discharge capacity was observed in composite V₂O₅-based cells over V₂O₅-based cells.     

Preparation of TiO<Subscript>2</Subscript>-coated LiCo<Subscript>1/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by electrostatic self-assembly method and its properties

A precursor of TiO₂–LiCo_1/3Ni_1/3Mn_1/3O₂ was prepared by electrostatic self-assembly method. The final product was obtained by heating the precursor at 400–450 °C for 4–6 h in air. X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical tests were used to examine the structural, morphology, elementary valence, and electrochemical characteristics. XRD indicated that the TiO₂-coated material can be indexed by α-NaFeO₂ layered structure, which belongs to hexagonal-type space group R3m. XPS results confirmed the existence of TiO₂ compound on the surface of the coated sample. The SEM image showed that the material had spherically porous morphology with the uniform size about 6 μm. The initial charge–discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ material was 168.8/160.0 mAh/g. After 60 cycles, the discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ sample was 147.0 mAh/g, and the coulombic efficiency was 94.0%. Compared with the uncoated sample, the electrochemical performance of TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ was improved.     

Lithiated c-V<Subscript>2</Subscript>O<Subscript>5</Subscript> thin-film as positive electrode for rocking-chair solid-state lithium microbattery

We report for the first time the use of lithiated crystalline V₂O₅ thin films as positive electrode in all-solid-state microbatteries. Crystalline Li_xV₂O₅ films (x ≈ 0.8 and 1.5) are obtained by vacuum evaporation of metallic lithium deposited on sputtered c-V₂O₅. An all-solid-state lithium microbattery of Li_1.5V₂O₅/LiPON/Li exhibited a typical reversible capacity of 50 μAh/cm² in the potential range 3.8/2.15 V which exceeds by far the results known on all-solid-state lithium batteries using amorphous V₂O₅ films and lithiated amorphous Li_xV₂O₅ thin films as positive electrode. Hence, the present work opens the possibility of using high performance crystalline lithiated V₂O₅ thin films in rocking-chair solid-state microbatteries.     

Current status of astronomical observations on possible cosmological variations of the proton-to-electron mass ratio μ=m<Subscript>p</Subscript>/m<Subscript>e</Subscript>

Astronomical constraints on a possible cosmologicalvariation of the proton-to-electron mass ratio μ=m_p/m_e are discussed. The analysis of H₂ lines observed in thespectra of distant quasars Q 0405-443 (z_em=3.02) andQ 0347-383 (z_em=3.22) is performed [1] using, partly, very precise values of H₂ frequencies from new laboratorymeasurements [2] and sensitivity coefficients from newaccurate calculations [2,3]. A possibleμ-variation of Δμ/ μ= (2.0±0.6)×10^-5over 12 Gyr is not excluded. However, the discussion of systematicerrors show that some may well be underestimated. Thus, the abovevalue should be treated as the most stringent limit the cosmologicalvariation of μ at z≈2.6 - 3.0 (12 Gyr ago).     

Studies on the Fluorescence Fiber-Optic DNA Biosensor Using <Emphasis Type="Italic">p</Emphasis>-Hydroxyphenylimidazo[f]1,10-phenanthroline Ferrum(III) as Indicator

A complex Fe(phen)₂·PHPIP·3ClO₄·2H₂O, where phen = 1,10-phenanthroline and PHPIP = p-hydroxyphenylimidazo[f]1,10-phenanthroline, was synthesized and acted as a good fluorescence indicator based on its interaction with double-duplex DNA. Then a fiber-optic DNA biosensor of fluorimetric detection was developed based on the recognition of target DNA in DNA hybridization assays. A probe ssDNA was covalently immobilized onto the surface of quartz optical fibers and then the probe ssDNA hybridized with complementary ssDNA introduced into the local environment of the sensor. The hybridization with complementary strands was monitored in real time by fluorimetric detection. Several factors affecting the probe immobilization, target DNA hybridization, and indicator binding reactions were optimized to maximize the sensitivity and shorten the assay time. Using this method, a sequence of the 16-mer oligonucleotides could be quantified over the range from 4.98 × 10⁻⁷ to 4.88 × 10⁻⁶ M and a detection limit of 1.08 × 10⁻⁷ M. And the designed optic-fiber biosensor could be conveniently regenerated by thermal denature. The utility of the novel hybridization indicator could provide a simple, rapid, low toxicity and reusable detection.     

Pseudo-capacitive properties of LiCoO<Subscript>2</Subscript>/AC electrochemical capacitor in various aqueous electrolytes

LiCoO₂ particles were synthesized by a sol-gel process. X-ray diffraction analysis reveals that the prepared sample is a single phase with layered structure. A hybrid electrochemical capacitor was fabricated with LiCoO₂ as a positive electrode and activated carbon (AC) as a negative electrode in various aqueous electrolytes. Pseudo-capacitive properties of the LiCoO₂/AC electrochemical capacitor were determined by cyclic voltammetry, charge–discharge test, and electrochemical impedance measurement. The charge storage mechanism of the LiCoO₂-positive electrode in aqueous electrolyte was discussed, too. The results showed that the potential range, scan rate, species of aqueous electrolyte, and current density had great effect on capacitive properties of the hybrid capacitor. In the potential range of 0–1.4 V, it delivered a discharge specific capacitance of 45.9 Fg^–1 (based on the active mass of the two electrodes) at a current density of 100 mAg^–1 in 1 molL^–1 Li₂SO₄ aqueous electrolyte. The specific capacitance remained 41.7 Fg^–1 after 600 cycles.     

Influence of carbon additive on the properties of spherical Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> and LiFePO<Subscript>4</Subscript> materials for lithium-ion batteries

Preparing spherical particles with carbon additive is considered as one effective way to improve both high rate performance and tap density of Li₄Ti₅O₁₂ and LiFePO₄ materials. Spherical Li₄Ti₅O₁₂/C and LiFePO₄/C composites are prepared by spray-drying–solid-state reaction method and controlled crystallization–carbothermal reduction method, respectively. The X-ray diffraction characterization, scanning electron microscope, Brunauer–Emmett–Teller, alternating current impedance analyzing, tap density testing, and electrochemical property measurements are investigated. After hybridizing carbon with a proper quantity, the crystal grain size of active materials is remarkably decreased and the electrochemical properties are obviously improved. The Li₄Ti₅O₁₂/C and LiFePO₄/C composites prepared in this work are spherical. The tap density and the specific surface area are as high as 1.71 g cm⁻³ and 8.26 m² g⁻¹ for spherical Li₄Ti₅O₁₂/C, which are 1.35 g cm⁻³ and 18.86 m² g⁻¹ for spherical LiFePO₄/C powders. Between 1.0 and 3.0 V versus Li, the reversible specific capacity of the Li₄Ti₅O₁₂/C is more than 150 mAh g⁻¹ at 1.0-C rate. Between 2.5 and 4.2 V versus Li, the reversible capacity of the LiFePO₄/C is close to 140 mAh g⁻¹ at 1.0-C rate.     

Spectroscopic Properties and Energy Transfer Analysis of Tm<Superscript>3+</Superscript>-Doped BaF<Subscript>2</Subscript>-Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>-GeO<Subscript>2</Subscript>-La<Subscript>2</Subscript>O<Subscript>3</Subscript> Glass

This paper reports on the spectroscopic properties and energy transfer analysis of Tm³⁺-doped BaF₂-Ga₂O₃-GeO₂-La₂O₃ glasses with different Tm₂O₃ doping concentrations (0.2, 0.5, 2.0, 2.5, 3.0, 3.5, 3.5, 4.0 wt%). Mid-IR fluorescence intensities in the range of 1,300 nm−2,200 nm have been measured when excited under an 808 nm LD for all the samples with the same pump power. Energy level structure and Judd-Ofelt parameters have been calculated based on the absorption spectra of Tm³⁺, cross-relaxation rates and multi-phonon relaxation rates have been estimated with different Tm₂O₃ doping concentrations. The maximum fluorescence intensity at around 1.8 μm has been obtained in Tm₂O₃-3 wt% sample and the maximum value of calculated stimulated emission cross-section of Tm³⁺ in this sample is about 0.48 × 10⁻²⁰ cm² at 1,793 nm, and there is not any crystallization peak in the DSC curve of this sample, which indicate the potential utility of Tm³⁺-doped BaF₂-Ga₂O₃-GeO₂- La₂O₃ glass for 2.0-μm optical fiber laser.     

Ni-MH battery based on plasticized alkaline solid polymer electrolytes

Solid-state nickel metal hydride cells were fabricated using plasticized alkaline solid polymer electrolytes (ASPE) prepared from polyvinyl alcohol (PVA), potassium hydroxide (KOH), alumina (α-Al₂O₃), and propylene carbonate (PC). The ASPE film with PVA/KOH/α-Al₂O₃/PC/H₂O weight ratio of 1.00:0.67:0.09:2.64:1.32 and conductivity of (6.6 ± 1.7) × 10⁻⁴ S cm⁻¹ was used in fabrication of the electrochemical cells. To investigate the electrochemical properties of the plasticized ASPE, cells with the configuration Mg₂Ni/plasticized ASPE/Ni(OH)₂ were fabricated. At the eighth cycle with a current drain of 0.1 mA and plateau voltage of ∼1.1 V, the discharge lasted for 14 h before the cell was considered to have failed. The failure mode of the cell was due to the formation of thin Mg(OH)₂ insulating layers.     

A novel anode-supported stable BaCe0.7Ta0.1Y0.2O3− δ membrane prepared by all-solid-state process for solid oxide fuel cells

BaCe_0.7Ta_0.1Y_0.2O_{3− δ} (BCTY) and BaCe_0.8Y_0.2O_{3− δ} (BCY) were synthesized by solid-state reaction method at 1,300 °C for 20 h. After being exposed in 3% CO₂ + 3% H₂O + 94% N₂ at 700 °C for 20 h, the BCTY exhibited adequate chemical stability against carbonations while BCY decomposed into BaCO₃ and CeO₂. The BCTY showed the similar thermal expansion behavior to BCY from room temperature to 1,000 °C in air. The BCTY displayed a conductivity of 0.007 S/cm at 700 °C in humid hydrogen, lower than that of BCY (0.009 S/cm). A fuel cell with 10-μm thick BCTY membrane prepared through an all-solid-state process exhibited 1.004 V for OCV, 330 mW/cm² for maximum output at 700 °C, respectively. Short-term test shows that the fuel cell performance does not degrade after 20 h.     

A novel approach to employ Li<Subscript>2</Subscript>MnSiO<Subscript>4</Subscript> as anode active material for lithium batteries

In the present paper, we describe utilization of cathode active material as anode active material, for example, Li₂MnSiO₄. The lithium manganese silicate has been successfully synthesized by solid-state reaction method. The X-ray diffraction pattern confirms the orthorhombic structure with Pmn2 ₁ space group. The Li/Li₂MnSiO₄ cell delivered the initial discharge capacity of 420 mA h g⁻¹, which is 110 mA h g⁻¹ higher than graphitic anodes. The electrochemical reversibility and solid electrolyte interface formation of the Li₂MnSiO₄ electrode was emphasized by cyclic voltammetry.     

Investigation on structural characteristics of PVDF–AgCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposite solid polymer electrolyte system

There has been an increasing interest towards the incorporation of nanosize ceramic fillers in polymer electrolytes. Solid polymer electrolytes based on polyvinylidene fluoride (PVDF), silver triflate (AgCF₃SO₃), and x wt% of aluminum oxide (Al₂O₃) nanopowders (where x = 1, 3, 5, and 10, respectively) have been prepared using solution casting technique. The structural characteristics of these thin film specimens were studied using Fourier transform infrared (FTIR) and X-ray diffraction (XRD) patterns at room temperature. The appearance of new absorption bands and gradual shifts observed in some characteristic peaks confirmed the complex formation between polyvinylidene fluoride and silver triflate. Furthermore, the addition of nanosized filler Al₂O₃ has also indicated the interaction of the filler with the polymer salt complex. The XRD patterns obtained for all these samples in the 2θ range 10° to 70° showed the amorphous nature of these samples. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006.     

One-step synthesis of colloidal Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> and γ-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles at room temperature

A facile room-temperature synthesis has been developed to prepare colloidal Mn₃O₄ and γ-Fe₂O₃ nanoparticles (5 to 25 nm) by an ultrasonic-assisted method in the absence of any additional nucleation and surfactant. The morphology of the as-prepared samples was observed by transmission electron microscopy. High-resolution transmission electron microscopy observations revealed that the as-synthesized nanoparticles were single crystals. The magnetic properties of the samples were investigated with a superconducting quantum interference device magnetometer. The possible formation process has been proposed.     

Low-temperature synthesis of Cu-doped Li<Subscript>1.2</Subscript>V<Subscript>3</Subscript>O<Subscript>8</Subscript> as cathode for reversible lithium storage

Li_{1 .2}V₃O₈ and Cu-doped Li_1.2V₃O₈ were prepared at a temperature as low as 300 °C by a sol-gel method. The structure, morphology, and electrochemical performance of the as-prepared samples were characterized by means of X-ray diffraction, scanning electron microscopy, electrochemical impedance spectroscopy, and the galvanostatic discharge–charge techniques. It is found that the Cu-doped Li_1.2V₃O₈ sample exhibits less capacity loss during repeated cycling than the undoped one. The Cu-doped Li_1.2V₃O₈ sample demonstrates the first discharge capacity of 275.9 mAh/g in the range of 3.8–1.7 V at a current rate of 30 mA/g and remains at a stable discharge capacity of 264 mAh/g within 30 cycles. Furthermore, the possible role that copper plays in enhancing the cycleability of Li_1.2V₃O₈ has also been elucidated.     

Luminescence of CaGa<Subscript>2</Subscript>Se<Subscript>4</Subscript>:Eu crystals

We have studied photoluminescence and thermoluminescence (PL and TL) in CaGa₂Se₄:Eu crystals in the temperature range 77–400 K. We have established that broadband photoluminescence with maximum at 571 nm is due to intracenter transitions 4f⁶ 5d–4f⁷ (⁸S_7/2) of the Eu²⁺ ions. From the temperature dependence of the intensity (log I–10³/T), we determined the activation energy (E _a = 0.04 eV) for thermal quenching of photoluminescence. From the thermoluminescence spectra, we determined the trap depths: 0.31, 0.44, 0.53, 0.59 eV. The lifetime of the excited state 4f6 5d of the Eu²⁺ ions in the CaGa₂Se₄ crystal found from the luminescence decay kinetics is 3.8 μsec. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 76, No. 1, pp. 112–116, January–February, 2009.     

Li4Ti2.5Cr2.5O12 as anode material for lithium battery

Chromium-substituted Li₄Ti₅O₁₂ has been investigated as a negative electrode for future lithium batteries. It has been synthesized by a solid-state method followed by quenching leading to a micron-sized material. The minimum formation temperature of Li₄Ti_2.5Cr_2.5O₁₂ was found to be around 600 °C using thermogravimetric and differential thermal analysis. X-ray diffraction, scanning electron microscopy, cyclic voltammetry (CV), impedance spectroscopy, and charge–discharge cycling were used to evaluate the synthesized Li₄Ti_2.5Cr_2.5O₁₂. The particle size of the powder was around 2–4 μm. CV studies reveal a shift in the deintercalation potential by about 40 mV, i.e., from 1.54 V for Li₄Ti₅O₁₂ to 1.5 V for Li₄Ti_2.5Cr_2.5O₁₂. High-rate cyclability was exhibited by Li₄Ti_2.5Cr_2.5O₁₂ (up to 5  C) compared to the parent compound. The conduction mechanism of the compound was examined in terms of the dielectric constant and dissipation factor. The relaxation time has been evaluated and was found to be 0.07 ms. The mobility was found to be 5.133 × 10⁻⁶ cm² V⁻¹ s⁻¹.     

Effects of dopant on the electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode materials

The effects of dopant on the electrochemical properties of spinel-type Li_3.97M_0.1Ti_4.94O₁₂ (M = Mn, Ni, Co) and Li_(4-x/3)Cr_xTi_(5-2x/3)O₁₂(x = 0.1, 0.3, 0.6, 0.9, 1.5) were systematically investigated. Charge-discharge cycling were performed at a constant current density of 0.5 mA/cm² between the cut-off voltages of 3.0 and 1.0 V, the experimental results showed that Cr³⁺ dopant improved the reversible capacity and cycling stability over the pristine Li₄Ti₅O₁₂. The substitution of the Mn³⁺ and Ni³⁺ slightly decreased the capacity of the Li₄Ti₅O₁₂. Dopants such as Co³⁺ to some extent worsened the electrochemical performance of the Li₄Ti₅O₁₂.     

Impedance spectroscopy study of Pb<Subscript>2</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript> compound

The lead pyrophosphate, Pb₂P₂O₇, compound was prepared by conventional solid-state reaction and identified by X-ray powder diffractometer. Pb₂P₂O₇ has a triclinic structure whose electrical properties were studied using impedance spectroscopy technique. Both impedance and modulus analysis exhibit the grain and grain boundary contribution to the electrical response of the sample. The temperature dependence of the bulk and grain boundary conductivity were found to obey the Arrhenius law with activation energies E _g = 0.66 eV and E _gb = 0.67 eV, respectively. The scaling behavior of the imaginary part of the complex impedance suggests that the relaxation describes the same mechanism at various temperatures.     

Photoluminescence of CuInS<Subscript>2</Subscript> single crystals grown by traveling heater and chemical vapor transport methods

Photoluminescence of CuInS₂ single crystals grown by both the traveling heater method (THM) and chemical vapor transport (CVT) has been investigated at 4.2, 78, and 300 K. Intense emission in the near-band-edge region caused by free and bound excitons has been detected for both types of crystals. Taking into account the energy position of the luminescence line of the ground (n = 1) and first excited (n = 2) states, the binding energy for free A excitons has been estimated to be about 19.7 and 18.5 meV for CuInS₂ grown by CVT and THM, respectively. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 76, No. 2, pp. 232–236, March–April, 2009.     

Synthesis of macroporous LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> with avian egg membrane as a template

Avian eggshell membrane as a template for the synthesis of a macroporous network of crystalline LiMn₂O₄ is demonstrated. Well-formed crystals of average size 600 nm formed a network structure whose average pore size was 2–4 μm. The unique porous structure should make it an attractive cathode material for lithium-ion batteries. In fact, for an 80% cutoff in capacity retention, LiMn₂O₄ obtained by a 10-h calcination at 800°C sustained 83 cycles.