ASE-HPLC检测某型号球形发射药中的叠氮硝胺、硝化甘油、Ⅱ号中定剂含量的研究

采用快速溶剂萃取（ASE）技术和高效液相色谱法测定某球形药中叠氮硝胺（DIANP）、硝化甘油（NG）和Ⅱ号中定剂（C2）的含量．ASE提取条件：二氯甲烷做萃取溶剂,萃取温度100℃,静态萃取10min,萃取2次．HPLC测定条件：YWGC18柱（150×4．6mm,10μm）,以甲醇和水作为流动相,梯度洗脱,流速1 mL／min,检测波长210nm．测定结果表明DIANP、NG、C2平均回收率分别为99．6％、100．3％、99．4％,RSD分别为0．7％、0．8％、0．9％（n=5）,检出限分别为2.1、1.5和0．2mg／L,线性范围分别为0．02～0．98g／L,0．03～1．38g／L,0．002～0．124g／L．用此方法共检测某批球形发射药样品5份,检测结果与滴析-HPLC法检测结果相当．     

某些变色酸双偶氮染料-蛋白质体系的共振瑞利散射及其分析应用

在PH3．4－4．0的缓冲溶液中， 偶氮胂M（AAM）、偶氮氯膦Ⅲ（CPAⅢ）和氯磺酚S（CSPS）等变色酸双偶氮染料及蛋白质本身的共振瑞利散射（RRS）均十分微弱，但这些染料与蛋白质结合形成复合物时能使RRS急剧增强，在400－470nm的范围内呈现高的散射强度，其最大散射波大均位于470nm处，并且散射强度分别在0．36mg/L（CPAⅢ体系）、0－3．8mg/L(AAM体系）和0－4．8mg/L(CSPS体系）的范围内与牛血清白蛋白（BSA）的浓度成正比，方法具有高灵敏度，对于BSA的检出限（σ=3时）分别为18．5μg/L（CPAⅢ）、13．6μg/L（CSPS）和27．9μg/L（AAM）。考察了共存物质的影响，表明方法具有较好的选择性，此法可用于人血清中蛋白质的测定。     

HPLC法测定鸡精中谷氨酸钠的含量

以邻苯二甲醛与谷氨酸钠中的氨基进行柱前在线衍生化反应,采用C18色谱柱分离、荧光检测器（激发340nm,发射450nm）进行测定,建立了柱前衍生反相高效液相色谱测定鸡精中谷氨酸钠含量的方法。该方法相对标准偏差为0．69％,加标回收率为99．1％～101％,在0．10~50．0mg／L范围内,谷氨酸钠的峰面积和浓度之间的相关系数为0．9999,保留时间和峰面积的相对标准偏差分别为1．22％和0．71％,鸡精中谷氨酸钠定量下限为0．2μg／g。     

紫外分光光度法测定异烟酸电氧化合成反应液的等吸收点

选择258nm和269nm为测定波长,用等吸收点双波长紫外分光光度法,对4-甲基吡啶（4-MP）直接电氧化合成异烟酸反应液中的异烟酸和4-MP进行了定量分析,异烟酸的检出限为3．5μmol／L,4．MP的检出限为3.8μmol／L,异烟酸和4-MP在硫酸水溶液中的吸光度加和性良好,两者测定结果的平均相对标准偏差分别为1．35％和0．83％;平均回收率分别为99％和100％。     

分光光度法同时测定无机多组分体系的研究III: 微量钨, 钼, 钛的测定

本文从配合物吸收光谱行为及矩阵运算角度分别探讨了CPA矩阵法AKC矩阵法中波长选择对分析结果误差的影响. 在前人有关钨, 钼, 钛单个元素光度测定研究的基础上, 确定了适宜于钨, 钼, 钛一苯基荧光酮-溴代十六烷基三甲铵三元配合物同时光度测定的最佳条件, 拟定了不经分离直接光度测定钨, 钼, 钛的方法.     

高效液相色谱法测定烧烫灵软膏中磺胺醋酰钠和磺胺含量

建立了用HPLC测定烧烫灵软膏中磺胺醋酰钠和磺胺含量的方法。在SpherisorbC18柱上,以V（甲醇）：V（体积分数为0．25％的醋酸溶液）=7：93为流动相,于257nm波长处检测。平均回收率：砍胶醋酰钠为98．9％（n=5）,RSD=0．64％;磺胺为99．3％（n=5）,RSD=1．58％。方法简便、快速、准确、重现性好。     

人工神经网络用于紫外光谱同时测定苯和甲苯及二甲苯的含量

根据反向传输（Backpropagation,BP）算法,应用三层ANN（人工神经网络,Artificial neural network）网络原理,对紫外光谱严重重叠的苯、甲苯和二甲苯的混合体系进行同时测定。在230～280nm范围内,以16个特征波长处的紫外吸光度作为网络特征参数,并通过均匀设计安排样本进行网络训练和计算。苯、甲苯和二甲苯的回收率依次为98．7％,99．4％和97．4％,测定结果的相对标准偏差分别为2．0％,2．8％和2．7％。     

反胶束萃取-高效液相色谱法测定磺酸型偶氮染料

建立了水中磺酸偶氮染料甲基橙（MO）、刚果红（CR）和酸性铬兰K（ACBK）的反胶束萃取-离子对高效液相色谱定量检测的方法。采用Hypersil C18柱（250×4．6mm,5μm）,流动相为V（甲醇）／V（水）=63：37（含10mmol／L的KH2PO4、4mmol／L的四丁基溴化铵,KOH调pH=7．0）,流速为0.8mL／min,MO、CR和ACBK检测波长分别为449nm、505nm和526nm。结果表明,染料的回收率为92．9％～102．1％,相对标准偏差为0．9％～2．3％,水中MO、CR和ACBK的检出限分别为0．6μg／L、1．2μg／L和1．3μg／L。     

胶束薄层扫描法测定黄连及其制剂中的小檗碱、巴马汀和药根碱

以2％CPC-醋酸乙酯(9：1)胶束溶液为展开剂,在聚酰胺薄膜上成功地分离了小檗碱、巴马汀和药根碱。以345nm为测定波长,550nm为参比波长进行扫描测定,建立了一种新的同时测定黄连及其制剂中小檗碱、巴马汀和药根碱的胶束薄层扫描法。小檗碱、巴马汀和药根碱的线性范围分别为0．2—2．4、0．1—1．0和0．1—1．0μg;回收率分别为97．7％-99．4％、101．7％～102．6％和96．7％-97．8％;相对标准偏差分别为1．4％-1．7％、1．9％-2．7％和1．8％-2．2％。     

毛细管气相色谱法测定深海鱼油中的EPA和DHA含量

用氢氧化钾－甲醇酯化法将深海鱼油中的脂肪酸快速、有效地转化成脂肪酸甲酯,然后进行毛细管气相色谱法测定,以二十二碳饱和脂肪酸甲酯为内标物,建立了5,8,11,14,17－二十碳五烯酸（EPA）和4,7,10,13,16,19－二十二碳六烯酸（DHA）的定量分析方法,并用于实际样品分析。该方法对EPA和DHA定量分析的相对标准偏差分别为4．6％和5．0％,回收率分别为99．7％和99．4％。     

Criteria for selecting analytical wavelengths for multicomponent mixtures by the CPA matrix method and simultaneous spectrophotometric determination of niobium and tantalum

The reversed matrix representation of the Lambert-Beer law (CPA matrix method) is applied in simultaneous spectrophotometric determinations. Restrictions on the selection of analytical wavelengths in applying the CPA matrix method are investigated experimentally and theoretically. Four criteria for selecting suitable wavelengths are described. A spectrophotometric procedure for niobium and tantalum with salicylfluorone and cetyltrimethylammonium bromide in the presence of tartaric acid was developed and used for the simultaneous determination of niobium and tantalum by the CPA matrix method. The absorption maxima were at 520 and 513 nm, respectively. Measurements at six wavelengths in the range 500–530 nm provided data from which niobium (0.04–0.4 μm ml^?1) and tantalum (0.08–0.8 μg ml^?1) were evaluated, with relative standard deviations of <2.     

CPA矩阵法测定肺保三效片中六组分含量

本文采用ＣＰＡ矩阵法测定肺保三效片中六种组分的含量．计算程序采用ＢＡＳＩＣ语言编制．扑热息痛、苯妥英钠、咖啡因、茶碱、扑尔敏和盐酸麻黄碱的平均回收率和相对标准偏差分别为９６．１５％，０．７７％；９６．１５％，０．７２％；９６．４１％，０．６１％；９６．２２％，０．７１％；９６．１３％，０．７４％；９６．１６％，０．７７％．结果较满意．     

偶氮氯膦Ⅰ分光光度法测定血清蛋白质的效果分析

在Na2HPO4-柠檬酸酸性缓冲液中,加入非离子表面活性剂聚氧乙烯月桂醚（Brij-35）,使偶氮氯膦Ⅰ（CPA—Ⅰ）与牛血清白蛋白形成复合物,复合物的最大吸收波长在570nm,比试剂本身红移了70nm,表观摩尔吸光系数为5．88×10^4L／（mol·cm^-1）,线性范围0—166mg／L,采用分光光度法研究该结合反应的最佳反应条件,并据此建立了一种测定血清蛋白质的新方法。结果表明,该法回收率为98．7％～102．2％,批内变异系数为2．4％,血清用量少,线性范围宽,具有操作快速、简便、结果灵敏可靠等优点,与双缩脲法相关性良好。     

Simultaneous Ultraviolet Spectrophotometric Determination of Nitrate and Nitrite in Water

Abstract

A rapid and accurate method for the direct simultaneous determination of nitrate and nitrite is proposed. The method is applied to the determination of nitrate and nitrite in rainwater and wastewater without preliminary separation. The determinations are performed by a CPA matrix method with ultraviolet spectrophotometric detection. The results obtained are in agreement with those obtained by conventional methods for the determination of nitrate and nitrite.     

流动注射-阻尼最小二乘法用于多组分分析

研究了用流动注射分析进行阻尼最小二乘分光光度法同时测定锌、铜和钴的新方法。方法基于阻尼最小二乘法改进CPA法,将阻尼因子和非零截距引入CPA法,降低了P系数矩阵的病态程度和改善了校正模型的预报能力,使结果更加准确,已将方法成功用于锌铜钴混合体系的分析。     

偏最小二乘分光光度法同时测定镍基合金中的铈和钇

以对乙酰基偶氮氯膦（ＣＰＡｐＡ）为显色剂，研究了同时测定Ｃｅ和Ｙ的最佳条件，由于二者吸收光谱严重重叠，本文运用偏最小二乘法实现了Ｃｅ和Ｙ的同时测定，结果满意。     

Determination of aluminum in highly concentrated iron samples: Study of interferences using high-resolution continuum source atomic absorption spectrometry

High-resolution continuum source atomic absorption spectrometry (HR-CS AAS) has been used to investigate spectral and non-spectral interferences found with a conventional line source atomic absorption spectrometer in the determination of aluminum in pharmaceutical products containing elevated iron and sugar concentrations. A transversely heated graphite furnace was used as the atomizer in both spectrometers. The two most sensitive aluminum lines at 309.3 nm and 396.2 nm were investigated and it was found that an iron absorption line at 309.278 nm, in the vicinity of the aluminum line at 309.271 nm, could be responsible for some spectral interference. The simultaneous presence of iron and the organic components of the matrix were responsible for radiation scattering, causing high continuous and also structured background absorption at both wavelengths. The aluminum and iron absorption could not be separated in time, i.e., the iron interference could not be eliminated by optimizing the graphite furnace temperature program. However, an interference-free determination of aluminum was possible carrying out the measurements with HR-CS AAS at 396.152 nm after applying least squares background correction for the elimination of the structured background. Analytical working range and other figures of merit were determined and are presented for both wavelengths using peak volume registration (center pixel ± 1) and the center pixel only. Limits of detection and characteristic masses ranged from 1.1 to 2.5 pg and 13 to 43 pg, respectively. The method was used for the determination of the aluminum contamination in pharmaceutical formulations for iron deficiency treatment, which present iron concentrations from 10 to 50 g l^− 1. Spike recoveries from 89% to 105% show that the proposed method can be satisfactorily used for the quality control of these formulations.     

Photostability of the laser dye DCM in various inorganic-organic host matrices

The laser dye, 4-dicyanomethylene-2-methyl-6-p-dimethylaminostyryl-4H-pyran (DCM) was incorporated in various inorganic-organic host matrices by the sol-gel technique. The photostability of the DCM-doped materials under CW argon laser irradiation was investigated. The absorption of DCM monomer ar 480 nm decreased with increasing irradiation time and was accompanied by an increase in the absorption at 352 nm by inactive photoproducts. Photostability was estimated by measuring the decay rates of DCM fluorescences in different host matrices. The rates exhibited two components; a rapid decay within the first several tens of seconds followed by a slower luminescence decay. The rapid decay depended upon the DCM content in the matrix while the slow decay component was related to the mobility of the DCM in the different matrices. The silica host matrix containing phenyl and a small amount of epoxy groups exhibited the best photostability of the materials examined.     

基体石墨的孔隙结构及其对单质Ag扩散的影响

高温气冷堆燃料元件的基体石墨是一种多孔复合材料,是燃料元件的主要组成部分,其结构影响燃料元件的性能和裂变产物在燃料元件中的扩散。 本文利用压汞法表征基体石墨的孔隙结构,并讨论了基体石墨制备工艺中最大压制压强与热处理过程对孔隙结构的影响。 结果表明,基体石墨大孔孔径分布为6001900 nm,高温热处理使基体石墨的总孔隙率、中值孔径、大孔孔容均减小;基体石墨热处理样品的大孔孔容随最大压制压强的增加而呈线性减少,热处理过程单质Ag在石墨基体中的扩散速度与大孔孔容变化具有正相关性。