纳米ATO颗粒粒度分布的脉冲超声波测量研究

讨论了脉冲超声波测量纳米ATO颗粒粒度分布方法中的3个步骤,即超声波衰减谱测量、严格数学模型的选型以及颗粒粒度分布的反演计算.通过发射脉冲超声波并利用变声程方法测量25 ℃时2%(体积分数)的纳米ATO-H2O分散液的超声衰减谱;选取McClements理论模型叠加BLBL理论模型共同描述纳米ATO颗粒分散液中的超声衰减现象;采用最优正则优化反演算法反演得到纳米ATO颗粒的粒度分布以及平均粒径.脉冲超声法检测结果显示,纳米ATO颗粒的平均粒径为25.6 nm,粒度分布为11.4 ～47.1 nm,CPS离心沉降纳米粒度分析仪测定结果分别为22.1 nm和10.1 ～62.6 nm.脉冲超声法检测结果与透射电镜图像以及离心沉降纳米粒度分析仪检测结果吻合较好,证明了脉冲超声波测量纳米颗粒粒度分布以及平均粒径的可行性与可靠性.     

纳米氧化锌的粒度控制与表征

采用溶胶-凝胶法制备了粒度小于10nm的ZnO纳米颗粒,用沉淀法制备了粒度大于10 nm的ZnO纳米颗粒.讨论了颗粒粒度的控制因素,得到不同粒度的产品.采用TEM、XRD、BET、UV-Vis等检测手段对不同粒度的ZnO纳米颗粒进行表征.结果表明粒度小于10 nm的ZnO纳米颗粒,具有量子效应,随粒度减小,紫外可见光光谱蓝移;粒度大于10 nm的ZnO纳米颗粒,不具有量子效应,它们的禁带宽度与块体ZnO的禁带宽度相同,为3.2 eV,不同粒度的ZnO纳米颗粒紫外可见光光谱相同.     

基于铜增强纳米金标记物结合磁分离的溶出伏安免疫分析法用于蛋白质的高灵敏测定

应用铜原位化学放大纳米金颗粒的信号增强特性, 并结合磁分离技术, 提出了一种高灵敏的溶出伏安免疫分析方法. 实验中以人IgG为模式蛋白质, 将抗体修饰的SiO₂@Fe₃O₄核壳型磁性纳米颗粒和纳米金标抗体悬浊液混合, 用以均相免疫识别人IgG, 借助外加磁场分离纯化, 在免疫复合物悬浊液中加入铜增强试剂进行沉积放大反应, 再将铜用稀硝酸溶解并进行溶出伏安分析检测. 结果表明, 与基于固相反应的金属免疫分析法相比, 所提出的基于均相反应和磁分离原理的方法具有操作简单、分析时间短等优点. 该方法显示出明显增强的人IgG检测性能, 其线性检测范围为01~1000 ng/mL, 检出限为73 pg/mL. 此外, 将其用于实际样品的回收率测定, 结果令人满意.     

石英纳米通道单磷脂囊泡的电阻-脉冲分析方法

本文报告了用于检测单囊泡及其粒径分析的石英纳米通道电阻-脉冲分析方法. 采用圆柱形石英纳米通道可检测粒径为100~300 nm的单磷脂囊泡和直径为170~400 nm的聚苯乙烯纳米颗粒. 单囊泡和纳米颗粒的迁移可通过检测各自产生的方波电流脉冲信号, 并由此确定颗粒尺寸. 结果表明,采用石英纳米通道电阻-脉冲分析方法得到的颗粒/囊泡粒径与采用动态光散射法和扫描电子显微法得到的结果完全一致. 这种基于电子的分析方法具有快速简单的特点,所用的自制微传感器廉价耐用. 石英通道的应用还可与其它分析方法如电流分析法和荧光显微法联用,以获得生物囊泡及人工囊泡更完全的信息.     

石英纳米通道单磷脂囊泡的电阻-脉冲分析方法（英文）

本文报告了用于检测单囊泡及其粒径分析的石英纳米通道电阻-脉冲分析方法.采用圆柱形石英纳米通道可检测粒径为100~300 nm的单磷脂囊泡和直径为170~400 nm的聚苯乙烯纳米颗粒.单囊泡和纳米颗粒的迁移可通过检测各自产生的方波电流脉冲信号,并由此确定颗粒尺寸.结果表明,采用石英纳米通道电阻-脉冲分析方法得到的颗粒/囊泡粒径与采用动态光散射法和扫描电子显微法得到的结果完全一致.这种基于电子的分析方法具有快速简单的特点,所用的自制微传感器廉价耐用.石英通道的应用还可与其它分析方法如电流分析法和荧光显微法联用,以获得生物囊泡及人工囊泡更完全的信息.     

锑掺杂二氧化锡实心球和空心球的碳还原制备及其生长机理研究

通过在水平管式炉中用石墨还原锑掺杂二氧化锡(ATO)纳米颗粒的方法制备了ATO的实心球和空心球, 并用EDX和XRD等技术分析了产物的物相和元素组成; 用FE-SEM和TEM观察了其形貌; 用HRTEM分析了其晶格结构. 结果表明, 产物为直径0.2~5 μm的ATO实心球和直径为2~20 μm的ATO空心球. 通过控制Ar流速和沉积位置控制了ATO实心球的尺寸和产量, 用Ostwald Ripening分析了ATO实心球的生长过程. ATO空心球的制备在具有较高氧浓度、长度稍长于刚玉管的陶瓷管中进行, 对其生长机理进行了讨论, 分析了相同条件下使用不同材质的管子生成不同形貌产物的原因.     

柔性透明自支撑氧化锡锑电纺纳米纤维膜的制备与表征

以四氯化锡和三氯化锑为前驱体,通过静电纺丝技术制备了柔性透明的自支撑氧化锡锑(ATO)纳米纤维膜.研究结果表明,该柔性ATO纤维膜具有四方相金红石晶体结构,且呈无规的纤维网状分布.当前驱体煅烧温度分别为520℃和700℃时,纤维的平均直径为200和150 nm;组成纤维的颗粒的平均粒径为10和19 nm;可见光透过率为72%和80%;电阻率为5.23和2.20Ω·cm.该自支撑ATO纳米纤维膜还显示出优异的柔韧性,在弯曲500次后其电阻率基本不变.     

多聚赖氨酸淀粉纳米颗粒基因载体的研制及应用

以可溶性淀粉为原料, 利用反向微乳液法, 加入交联剂三氯氧磷, 制备了直径为50 nm左右带负电荷的交联淀粉纳米颗粒. 以该纳米颗粒为内核, 经多聚赖氨酸修饰, 得到了多聚赖氨酸淀粉纳米颗粒(PLL-StNP). 对PLL-StNP进行了颗粒粒度、稳定性和电性的表征, 并通过颗粒的体外细胞毒性检测、颗粒与DNA结合能力及细胞转染等方面的分析, 发现多聚赖氨酸淀粉纳米颗粒(PLL-StNP)有可能作为基因载体, 在此基础上发展了多聚赖氨酸淀粉纳米颗粒基因载体的构建与基因转染技术. 作为非病毒基因载体, 赖氨酸淀粉纳米颗粒具有基因装载量大、转染率高、细胞毒性低以及可生物降解等优点.     

环氧化物法制备锑掺杂氧化锡气凝胶

以无机金属盐为前驱体,采用环氧丙烷添加法结合CO2超临界流体干燥和热处理工艺,制备了不同锑掺杂浓度的二氧化锡(ATO)气凝胶.所得气凝胶为深蓝色块体,平均密度约为600 mg?cm-3,锑掺杂浓度在5%到20%(x)之间.电子显微镜图片显示ATO气凝胶的骨架由粒径约为数十纳米的颗粒堆积而成,而这些颗粒又由数纳米的初级球形颗粒构成.X射线衍射谱表明,样品的主要晶相为SnO2四方相金红石结构,锑的掺杂仅引起微小的晶格畸变.X射线光电子谱显示锡元素以+4价态存在,而锑则具有+3和+5的混合价态.四探针电阻率测试仪的结果表明,ATO气凝胶的电阻率在2.7-40Ω?cm之间变化,其中在锑掺杂浓度(x)为12%时具有最低电阻率.     

天然松香用于制备球型纳米银的研究

以AgNO3为原料,利用天然松香中的还原性物质枞酸还原银氨络离子得到银纳米颗粒,利用油酸等与纳米颗粒的相互作用在表面形成一层保护层来防止纳米颗粒的聚集。并用UV-vis、TEM和XRD对其进行检测和表征。通过控制反应条件,可制得粒度分布较均匀、结晶性能良好的银纳米颗粒。     

Preparation and liquid crystalline properties of spherical cellulose nanocrystals

A novel kind of spherical cellulose nanocrystal (SCNC) suspension was prepared by hydrolysis of microcrystalline cellulose with a mixture of sulfuric acid and hydrochloric acid under ultrasonic treatment. The mechanism of SCNC formation and the liquid crystalline properties of their suspensions were investigated. A suspension of spherical particles was usually inclined to form crystallization colloids rather than liquid crystals at high concentration. However, a SCNC suspension with high polydispersity (49%) was observed to form the liquid crystalline phase, and the liquid crystalline textures changed with increasing concentration. This observation offers an approach to the liquid crystal formation of highly polydisperse spherical nanoparticles.     

Influence of ultrasonic stimulation on the growth and proliferation of Oryza sativa Nipponbare callus cells

Ultrasound acts as an alternative stress on cells or tissues. In this study it is aimed to investigate the effect of ultrasonic stimulation on the growth and proliferation of Oryza sativa Nipponbare cells (rice callus) in suspension culture. After the samples were stimulated by ultrasound at 28 kHz, we measured their growth and proliferation by using a colorimetric MTT ((3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide) assay as well as fresh weights of the cells. Growth curves were obtained by fresh weights in the suspension culture after ultrasonic agitation for different time from 2 to 120 s. In MTT method, the optical density was determined at 570 nm in the cell suspension on 10 days after the ultrasonic agitation. Up to 5 s agitation OD₅₇₀ increased; it decreased for more prolonged stimulation. We found that ultrasonic stimulation could promote the growth and proliferation of O. sativa Nipponbare cells in suspension culture with the optimal stimulation of 5 s, while with longer agitation, its growth and proliferation was inhibited. The mechanism may be that the ultrasound activated or destroyed the cellular structure, such as cell membrane, cytoskeleton and mitochondria in which many enzymes and ion channels are affected. In addition, the enhancement of cell wall and cell membrane fluidity might be one of the factors to promote the cell growth in 5-s ultrasonic stimulation.     

Influence of ultrasonic field on microcystins produced by bloom-forming algae

Under the background of algae removal and growth inhibition by ultrasonic irradiation, the effects of ultrasonic irradiation on removal of Microcystis, the concentration variation of microcystins (MC) produced by Microcystis in Microcystis suspension, and sonochemical degradation of microcystins in water, were studied in the paper. The results showed that ultrasonic irradiation could efficiently inhibit the growth of Microcystis, and ultrasonic irradiation shorter than 5 min would not introduce the increase of microcystins dissolved in Microcystis suspension simultaneity. Also, microcystins dissolved in Microcystis suspension would not increase as ultrasonic power increasing. Further research showed that microcystins were effectively degraded in ultrasonic fields. After 20 min ultrasonic irradiation at 150 kHz and 30 W, the removal rate of microcystins reached 70%.     

超声无皂乳液聚合制备BA/St/AM三元共聚物乳胶粒及其聚合机理研究

将超声技术引入到无皂乳液聚合方法中,在不加入任何引发剂和乳化剂的情况下,制备了丙烯酸丁酯(BA)/苯乙烯(St)/丙烯酰胺(AM)三元共聚纳米乳胶粒.研究了不同超声时间对单体转化率、乳胶粒粒径以及乳液粘度的影响.同时还探讨了超声无皂乳液聚合机理,认为AM在聚合过程中起到了引发和稳定的作用.TEM照片表明,乳胶粒直径大约在80nm左右,FTIR及DSC分析表明产物为三元共聚物,而不是共混物.     

Analysis of Food Products Using Carbonization and Ultrasonic Techniques

It was shown that food samples of vegetable and animal origin can be analyzed using the direct introduction of an aqueous suspension of ash resulting from their incomplete mineralization (carbonization) into an electrothermal atomizer of an atomic absorption spectrometer. With the ultrasonic stabilization of the aqueous suspension, the performance characteristics of the analytical results can be improved compared to those in classical dry ashing and the time of analysis can be shortened by 4–10 times.     

Fast Electrochemical Characterization of Historical Glasses Using Carbon Screen‐Printed Electrodes and Ultrasonic Assisted Sampling

A new method for lead oxide (PbO) analysis in glasses, using a carbon screen printed electrode (SPE) is proposed. A suspension of the powdered glass sample in nitric acid is prepared using an ultrasonic probe, 100 µL of slurry are deposited on the SPE and the voltammetric measurement is carried out. Structural information of PbO in the glass matrix is obtained by CV. Lead quantification is performed by DPV. In the best conditions a LOD of 2.30 wt% of PbO was obtained. The method has been applied with good results in the analysis of historical glasses samples.     

Effect of ultrasonic waves on crocin and safranal content and expression of their controlling genes in suspension culture of saffron (Crocus sativus L.)

The expression of biosynthesis controlling genes of crocin and safranal in saffron (Crocus sativus) can be influenced by ultrasonic waves. Sterilized saffron corms were cultured in a ½-MS medium supplemented by 2-4-D and BAP. Saffron callus cells were treated with ultrasonic waves in a cellular suspension culture under optimal growth conditions. The samples were collected at 24 and 72 hours after treatment in three replications. The secondary metabolites were measured by high-performance liquid chromatography and the gene expression was analysed by the real-time polymerase chain reaction. Results indicate that this elicitor can influence the expressions of genes CsBCH, CsLYC and CsGT-2; the ultrasonic waves acted as an effective mechanical stimulus to the suspension cultures. The analysis of variance of the ultrasonically produced amounts of safranal and crocin indicates that there is a significant difference between once- and twice-treated samples in that the amount of safranal was the highest within the samples taken from the twice-treated suspension culture at 72 h after the ultrasound treatment, and the crocin was maximised after 24 h passed the twice-applied ultrasound treatment.     

Preparation of stable aqueous suspension of a hydrophobic drug with polymers

Pharmaceutical preparation of a hydrophobic aldose reductase inhibitor 5-(3-ethoxy-4-pentyloxyphenyl)-2,4-thiazolidinedione (CT112) was investigated. CT112 dissolved in a basic solution with different kinds of polymers was neutralized by acid to obtain a suspension preparation. In particular, the addition of a polymer, hydroxypropyl methyl cellulose (HPMC) provided a stable CT112 suspension with a homogeneous particle size, and there seemed to be an optimal concentration of HPMC for the stable suspension. The addition of polysorbate 80 brought higher CT112 solubility in water, but did not provide a stable suspension. X-ray diffraction, IR spectrum, and thermal analysis revealed that the particles in the suspension with HPMC had lower degree of crystallinity, less hydrophobic particle surface, and lower melting point and decreased fusion enthalpy than the suspension without HPMC. These results suggested that the highly stable CT112 suspension could be attained by the adsorption of the polymer.     

低剪切混合方法制备炭黑/聚丙烯纳米复合材料及其电性能研究

采用一种在低剪切应力场下纳米复合材料的加工方法,制备得到纳米炭黑(CB)粒子在聚丙烯(PP)中以纳米尺度分散的聚合物导电复合材料.扫描电镜观察表明CB粒子在纳米复合材料中以纳米尺度存在,并均匀的分布在PP基体中.电性能测试发现,通过这种低剪切混合方法得到的纳米复合材料具有非常低的导电逾渗阈值(vc=2.49vol%)和较高的临界电阻指数(t=5.82),很大的偏离了普适逾渗理论.基于隧道逾渗模型对体系的电导率进行了模拟,并对CB的分散状态与导电网络的关系进行了分析.发现当纳米CB粒子以纳米尺度分散于基体中时,并不遵从接触导电机理,而是隧道逾渗机理在CB/PP纳米复合材料中起主导作用.     

PHOTOCHEMICAL PROPERTIES OF ERYTHROCYTE GHOSTS CONTAINING PORPHYRIN

Abstract— Rabbit erythrocyte cell ghosts were prepared containing tetrasodium meso-tetra (4-sulfona-to-phenyl) porphine (12-hydrate), a water soluble porphyrin. Laser flash kinetic spectroscopy of the suspension revealed a difference spectrum consistent with the porphyrin T, state. The time profiles of the signal decay were bi-exponential, and oxygen quenched each of the two components differently. Triplet-triplet extinction coefficients and quantum yields were lower for the ghost suspension than for porphyrin in solution. Fluorescence lifetime studies of the suspension also showed the presence of two components. Singlet oxygen luminescence, as measured by germanium diode detection, was observed, with a lifetime of 46 (jls and a 4>A of 0.09.