水平管降膜蒸发器传热优化研究

基于分布参数方法,对大型制冷系统中的水平管外降膜蒸发进行了传热优化数值模拟计算.在计算中,分析了饱和的液态制冷剂R134a在水平的铜管束外流动蒸发的换热特性.模型考虑了不同的管子类型和2流程不同管程布置对蒸发器换热特性的影响,结果表明,蒸发器采用Turbo-EHP管的性能高于其它管;不同管程布置对蒸发器性能的影响比较大,其中,下进上出管程布置的换热性能优于其它管程布置.同时,本文考虑了传热管外"干斑"对换热的影响.本文结论对于大型制冷系统中的降膜蒸发器传热优化设计具有指导性意义.     

Thermal control of electronic equipment by heat pipes

In the frame of the BRITE-EURAM european programme (KHIEPCOOL project), a literature survey on the main heat pipe and micro heat pipe technologies developed for thermal control of electronic equipment has been carried out. The conventional heat pipes are cylindrical, flat or bellow tubes, using wicks or axial grooves as capillary structures. In the field of micro heat pipes, three and four corner tubes have been developed. The pipes are mounted on single chips, in-line chip arrays or integrated into the component interconnection substrate. The best performances were achieved with Plesch's axially grooved flat miniature heat pipe [1], which is able to transfer a heat flux of about 60 W·cm⁻². Theoretical models have shown that the performance of micro heat pipe arrays increase with increasing tube diameter, decreasing tube length and increasing heat pipe density. The heat pipe technologies are classified and compared according to their geometry and location in the system. A list of about 150 references, classified according to their subjects, is presented.     

BOILING CHARACTERISTICS OF R-11 IN COMPACT TUBE BUNDLES WITH SMOOTH AND ENHANCED TUBES

This study presents new data on nucleate boiling heat transfer obtained in compact horizontal tube bundles with small tube gaps. The experiment investigates the heat transfer enhancement effects by the restricted spaces comprising the compact tube bundles and the enhanced heat transfer tubes for nucleate boiling heat transfer of R-11 at atmospheric pressure. A roll-worked tube was used as a new type of enhanced heat transfer tube. The experimental results show that the small tube gaps can greatly enhance boiling heat transfer in a smooth tube bundle, while enhancement effects of small gaps were not quite significant for the enhanced tube bundle. There is a compound effect from the enhanced surface and the restricted space only for the enhanced tube bundle with the tube gap of 0.5 mm. The effects of the tube positions within both compact tube bundles on the boiling heat transfer were minor.     

EXPERIMENTAL STUDY OF HEAT TRANSFER FROM A DISCRETE SOURCE TO A CIRCULAR LIQUID JET WITH ANNULAR COLLECTION OF THE SPENT FLUID

This study reports an experimental investigation of evaporative heat transfer and pressure drop of R-134a flowing downward inside vertical corrugated tubes with different corrugation pitches. The double tube test section is 0.5 m long with refrigerant flowing in the inner tube and hot water flowing in the annulus. The inner tubes are comprised of one smooth tube and three corrugated tubes with different corrugation pitches of 6.35, 8.46, and 12.7 mm. The test runs are performed at evaporating temperatures of 10°C, 15°C, and 20°C; heat fluxes of 20, 25, and 30 kW/m²; and mass fluxes of 200, 300, and 400 kg/m²s. The experimental data obtained from the smooth tube are plotted with flow pattern map for vertical flow. Comparisons between smooth and corrugated tubes on the heat transfer and pressure drop are also discussed. It is observed that the heat transfer coefficient and frictional pressure drop obtained from the corrugated tubes are higher than those from the smooth tube. Furthermore, the heat transfer coefficient and frictional pressure drop increase as the corrugation pitch decreases. The maximum heat transfer enhancement factor and penalty factor are up to 1.22 and 4.0, respectively.     

细圆管内流动凝结换热的实验研究

通过实验,分析细圆管的倾斜角度和管径对管内蒸气流动凝结换热的影响。利用实测的管壁温度变化。估计凝结液沿周向的分布。探讨不同倾角和管径条件下;重力作用影响凝结换热的机制。研究表明,在小尺度下,重力的影响受蒸气剪切力和表面张力作用而削弱,现有通行的关联式不适用于细圆管内的凝结换热。     

螺旋折流片换热器壳侧传热与流动的数值模拟

提出了一种强化管壳式换热器壳侧传热的螺旋折流片式换热器新方案,该方案在部分管子上套上螺旋折流片,不仅强化传热,而且对相邻管子形成支撑;利用FLUENT流体计算软件对同心套管螺旋折流片式换热段的壳侧流场、温度场进行了数值模拟,并讨论了螺旋角对其强化传热和阻力性能的影响。结果显示螺旋折流片诱导的涡旋流动对于减薄边界层,促进近壁流体与主流区流体的动量和质量交换进而强化传热有明显的作用,传热系数可比光管提高约40％-100％,但其流动阻力也将增大。     

R134a在水平三维内微肋管内的沸腾换热

本文以 Ｒ１３４ａ为工质,在外径为 １６ ｍｍ的两种不同几何结构的水平三维微肋管内进行了沸腾换热实验,研究了质量流率、热流密度、蒸汽干度等因素对沸腾换热系数的影响。与相同工况下的水平光管比较, １＃微肋管的换热强化因子在１．５～２．１之间,２＃微肋管的换热强化因子在１．９～２．８之间。两种三维微肋管的比较结果显示,单位内表面积上具有更多的微肋数目的 ２＃管的平均沸腾换热系数比 １＃管增加了 ２８～４３％。     

具有微槽的圆管流动沸腾实验研究

1引言行化行业大量的立、卧式重沸器等中都涉及沸腾相变传热。超大规模集成电路的正常工作需要具有10’W／m’量级甚至更高的散热能力山，航天热环境控制也同样要求在小温差下具有极高的散热强度问。对于这些高热流、低温差传热问题，往往也采用沸腾相变的方法解决。沸腾强化技术研究有很长历史，已发展出许多有效的方法，Thome问对过去数十年的工作做了系统的综述。具有烧结多孔表面薄展的HIGHFLUX管则，机加工扩展表面的THERMOEXEC－E管问，西德研制的GEWA－T管问，虽然在强化池沸腾时具有优异性能，很少用于强化流动沸腾。在…     

表面作用对分离式热管小螺旋管蒸发段两相流动与换热特性的影响

本文应用界面化学理论研究表面作用对分离式热管小螺旋管蒸发段管内流动和换热特性的影响。通过实验及分析,提出通过在一定范围内提高热管工作温度和添加润湿剂以降低水的表面张九提高管内壁的粗糙度以增强液膜的铺展性能。利用这两种方法可以有效地增强小螺旋管内壁面的润湿性能,从而提高管内换热性能．     

FC-72在浸泡于液池中的微小圆管内的沸腾传热

本文对浸泡于FC-72液池中的两个微小圆管进行了沸腾实验研究,得到了沸腾曲线和传热系数,并用DV摄像机拍摄到了圆管出口处的沸腾状况,研究了管道尺寸对沸腾传热特性的影响。实验结果显示,管道尺寸对沸腾传热特性有显著的影响。传热系数和CHF随着管道尺寸的缩小而减小.直径为1.10mm的圆管出口处在低热负荷加热时发生了汽泡阻塞,并导致了剧烈的沸腾滞后现象。     

BOILING HEAT TRANSFER MECHANISMS IN A HORIZONTAL TUBE BUNDLE

The effect of thermal environment on boiling heat transfer performance in a section of a horizontal tube bundle was investigated using R-113 as the working fluid. The in-line tube bundle has five columns and 27 rows with a pitch-to-diameter ratio of 1.3. Heal transfer coefficients obtained from the instrumented tube in the tube bundle with only one tube heated while the other tubes remained unhealed and with all the lubes in the bundle heated are reported for a range of heat flux, pressure, mass flow rate, and quality. The results showed that heat transfer coefficient of a tube in a heated bundle is slightly higher than that in an unhealed bundle, with the variation of heat transfer coefficient decreasing as heat flux, mass flow rate, or pressure increased. It was also found that higher quality would tend to improve the heat transfer. However, the effect of quality disappeared as heat flux, mass flow rate, and pressure increased. Based on the experimental data, the mechanism of the heat transfer augment due to thermal environment was analyzed. It was proposed that fluid agitation and thin liquid film formation are two main factors for a heated bundle to have better transfer performance than an unhealed bundle,     

非共沸混合物微翅管内强制对流蒸发换热计算

分析了非共沸混合物在水平微翅管内强制对流蒸发换热的传热传质的特点,考察了影响非共沸混合工质强制对流蒸发换热的主要影响因素,建立了考虑相界面传质阻力和微翅管二次流效应的换热系数的计算模型,利用本文模型的计算结果与实验数据进行了比较,吻合较好。在高质量流量和高干度(x>0.3)下,理论预测值与实验值的平均偏差不大于10％。     

R134a管外强化沸腾实验数据处理新方法

在水平管外沸腾换热实验中,热流密度沿管长方向的变化幅度较大,采用Wilson方法所得到的管内对流换热系数偏高,而管外沸腾换热系数偏低.为解决这一问题,本文提出了一种新的数据处理方法-局部换热系数法,并采用这种方法对实验测定R134a在水平放置的机械加工强化表面沸腾传热管的实验数据进行分析和处理,得到了较合理的结果.     

内螺旋肋管流动与传热特性的实验研究

对六种内螺旋肋管进行了流动与传热的实验研究,实验管内径为16．25-16．69 mm,内螺旋肋高为0．28-0．44 mm,螺旋肋牙数为40-45,螺旋角为43°-45°．研究表明,内螺旋肋管可以有效地强化传热,本文所研究的管型的传热强化倍率为1．67-2．99．比较了两种评价内螺旋肋管性能的方法．用Webb模型及Ravigururajan模型对内螺旋肋管进行了性能预测并与实验值进行了比较．两个模型的预测值与本试验结果有较大偏差,相对而言,传热模型稍优．     

蒸气在倾斜细小直径圆管内的流动凝结换热特性

细小管内的流动凝结换热具有许多超常换热特性,经典的Ｎｕｓｓｅｌｔ分析方法已不能满足需要。在以往研究的基础上,本文进一步通过实验探析换热温差和蒸气流量对不同直径的细小管内流动凝结换热的影响。研究表明,管径越小,换热温差对凝结换热系数的影响程度越低;通过流量和倾角对凝结换热数的影响,分析了重力引发的流动分层和剪切力对凝结液的排除两种因素对细管传热强化的作用机制。本文的实验结果和用于常规尺度下的通用关联式对比表明,采用细管,管内的流动凝结换热得到无可置疑的强化     

水蒸汽在水平三维微肋管内的凝结换热及阻力特性

本文以水蒸汽为工质对水平三维微肋管内凝结换热及阻力特性进行了实验研究．与光管和二维管相比，在相同条件下，实验中效果最好的T3管全长平均凝结换热系数分别提高了113％～410％和20％～65％，同时，与二维管相比流动阻力增加较小，最大值不超过6．3％．比较另两种管型（T1，T2管）也证明三维管以较小的流阻增加为代价换取了明显的强化效果．     

镀层微观结构对凝结换热的影响

通过研究Ni-P化学镀层管不同微观结构对凝结传热的影响,表明用化学镀表面改性的镀管相对于普通的碳钢管,具有明显促进珠状凝结的效果,在凝结过程中表现为珠膜共存状态,可以获得较好的换热性能。同时镀层对换热性能的改善与镀层中纳米相的含量相关,随着纳米相含量的降低,镀层的表面能也随着降低,换热效率得到增强。增加镀层的非晶度可以获得更好的珠状凝结的效果。     

不凝气体对R123凝结换热的影响

对氟利昂 R123 在水平单管外的凝结换热性能进行了试验研究,试验管为光管和五根强化管.目的是获得不凝气体对 R123 蒸气凝结时最佳肋密度的影响.试验结果表明:光管管外 Nusselt 理论值与实验数据偏差在±5%以内.对于含 8%不凝气体的 R123 在低肋管外的凝结换热,在肋密度为 1475 翅/米时可以获得最佳的换热性能.含不凝气体的 R123凝结换热系数显著下降,其管外换热系数约为纯蒸气的 20%～25%.随着肋密度的减小,不凝气体对凝结换热的影响逐渐减弱,但其最佳肋间隙仍保持不变,均为 0.32 mm.     

组合曲线回归法计算螺旋扁管管内对流传热系数

针对螺旋扁管壁面温度难于准确测试的特点,提出采用线性曲线回归与非线性曲线回归相结合的方法进行管内传热系数计算.进行了光管与螺旋扁管管内对流传热实验,并用该方法计算管内对流传热系数.光管传热系数计算值与经典公式的大偏差小于6%.螺旋扁管管内传热系数的计算值略大于通过测量壁温获得的传热系数值,分析了二者存在差异的原因.组合...     

细圆管内纳米悬浮液对流换热的实验研究

实验研究了细圆管内氧化铜纳米颗粒悬浮换热特性。试验段的管径为0.68mm、1.01mm和1.28mm,氧化钢纳米颗粒平均粒径为50um,悬浮液中氧化铜纳米颗粒质量分数分别为0.02,0.04和0.06,分散剂十二烷基苯磺酸钠(SDBS)质量的分数为0.02。为进行对比分析,还测试了水的换热特性。实验结果表明,在所研究的尺寸下,层流时去离子水的努谢尔特数Nu要高于已有液体对流换热关联式计算之值,纳米颗粒悬浮液的对流换热系数高于水的,且纳米颗粒的质量分数越高,悬浮液的对流换热系数越大。随着流动从层流向湍流的转换,强化效果也越明显。