Optimization of a flow injection system with amperometric detection for arsenic determination.

A selective and sensitive analytical procedure for rapid arsenic determination by gas-diffusion flow injection analysis with amperometric detection was developed. The method is based on the arsenite reduction by NaBH(4). Derived arsine diffuses through a PTF membrane into the acceptor flow stream and is amperometrically determined on a platinum working electrode. The limit of detection (3 sigma) at room temperature was 5 microg/dm(3) of As(III). The relative standard deviation for a 1 mg/dm(3) As(III) standard was 1.96% for six repetitive injections. Arsenic(V) was determined after its prereduction with potassium iodide. Arsenic determination was not interferred with by 1 mg/dm(3) Sb(III), 5 mg/dm(3) Sn(II), 10 mg/dm(3) Se(IV), 1 mg/dm(3) As(V), 1 mg/dm(3) hydrasine, 1 mg/dm(3) Fe(II) or 0.5 mg/dm(3) Fe(III) solution. The throughput of this method was 60 analyses per hour. This method was successfully applied to arsenic determination in some power plant waste water samples.     

Determination of calcium and magnesium in limestone and dolomite by enthalpimetric flow-injection analysis

A flow-enthalpimetric method for the determination of calcium and magnesium in limestone and dolomite is described. Calcium is determined by measuring the heat evolved from the substitution reaction with Mg-EDTA. The amount of magnesium is calculated from the calcium content and the enthalpimetric signal for the reaction of the sample solution with disodium-EDTA, which gives the total concentration of calcium and magnesium. Analysis of reference materials and other samples indicates an error not exceeding 0.3% of CaO and MgO, and a sampling rate of 100 samples per hour.     

Determination of nitrite by flow injection spectrophotometry using a home-made flow cell detector.

A simple, rapid, low cost and accurate determination using flow injection spectrophotometry with a home made flow cell detector, in combination with green LED and photodiode, had been developed for nitrite based on the Griess-Saltzman reaction, measuring the absorbance at 525 nm. The proposed system is able to monitor nitrite in freshwater samples at a throughput of 60 samples per hour with a relative standard deviation (%RSD) of less than 2.4% and a detection limit of <7 microg dm(-3). The calibration graph was linear between 0.010 - 1.0 mg dm(-3).     

Quantification of anions and cations in environmental water samples. Measurements with capillary electrophoresis and indirect-UV detection.

The aim of this study was to validate two separation methods for determination of inorganic anions and cations from natural waters with capillary electrophoresis (CE) by using indirect-UV detection. The research is related to method development for screening of groundwater samples obtained in site investigations for spent fuel of the Finnish nuclear industry. In CE analysis, anions were separated in pyromellitic acid (pH 7.7) in the order bromide, chloride, sulphate, nitrite, nitrate, fluoride and dihydrogenphosphate. Cations were separated at pH 3.6 after anions using an 18-crown-6-ether solution. In these analyses, ammonium migrated first followed by potassium, calcium, sodium and magnesium. The concentrations of the ions in the natural water samples were calculated by using two or three calibration curves made using reference solutions at concentration levels of 0.5-250 mg/l. The repeatabilities of the anion and cation methods were tested using laboratory-made reference sample mixtures with high and low salt concentrations. The limits of quantification in the analyses were between 0.02 and 0.1 mg/l, depending on the ion. Concentrations of ions tested in natural waters varied from a few milligrams to tens of grams per litre.     

A simple spectrophotometric method for the determination of copper in industrial, environmental, biological and soil samples using 2,5-dimercapto-1,3,4-thiadiazole.

A simple spectrophotometric method is presented for the rapid determination of copper at a trace level using 2,5-dimercapto-1,3,4-thiadiazole (DMTD) as a new spectrophotometric reagent. The method is based on the reaction of non-absorbent DMTD in a slightly acidic (0.002-0.014 mol dm(-3) sulfuric acid) aqueous solution with copper(II) to produce a highly absorbent greenish-yellow chelate product that has an absorption maximum at 390 nm. The reaction is instantaneous and the absorbance remains stable for 24 h. The average molar absorption coefficient and Sandell's sensitivity were found to be 5.65 x 10(4) dm3 mol(-1) cm(-1) and 10 ng cm(-2) of CuII, respectively. Linear calibration graphs were obtained for 0.1-20 microg cm(-3) of CuII; the stoichiometric composition of the chelate is 1:2 (Cu:DMTD). A large excess of over 50 cations, anions and complexing agents (e.g. tartrate, oxalate, citrate, phosphate, thiourea, SCN-) do not interfere in the determination. The method was successfully used for the determination of copper in several Standard Reference Materials as well as in some environmental water samples, biological samples, soil samples and solutions containing both copper(I) and copper(II) and complex synthetic mixtures. The method has high precision and accuracy (s = +/-0.01 for 0.5 microg cm(-1)).     

Sequential injection analysis for Cr(VI) and Cr(III) with renewable surface reflection spectrophotometry.

On the basis of the chromogenic reaction of chromium(VI) with 1,5-diphenylcarbohydrazide (DPC) on the surface of Polysorb C-18 beads and the sequential injection renewable surface technique (SI-RST), a highly sensitive reflect spectrophotometric method for the determination of chromium(III) and chromium(VI) was proposed. Considerations of system and flow cell design, and factors that influence the determination performance were discussed. With 300 microl of sample loaded and 0.6 mg of beads trapped, the linear response range was 0.02 - 0.5 mg l(-1) Cr(VI) with a detection limit (3 sigma) of 2.4 microg l(-1) Cr(VI). The method achieves a precision of 1.3% RSD (n = 11) and a throughput of 53 samples per hour. The determination of Cr(III) was based on the same reaction for the determination of Cr(VI) after being oxidized by (NH4)2S2O8. The precision of the oxidation method was evaluated using a 0.2 mg l(-1) Cr(III) standard, yielding an RSD of 2.5% (n = 11). The average recovery of Cr(III) oxidized was tested to be 99.1%. The proposed method was used in the simultaneous determination of Cr(VI) and Cr(III) in water samples, and the error was less than 3%.     

Application of sequential injection analysis to the determination of cationic surfactants based on the sensitized molybdenum-bromopyrogallol red reaction.

The aim of this work was to develop a simple, automatic system for the evaluation of cationic surfactants by combining sequential injection analysis and the sensitized effect of cationic surfactants on the reaction between metal ions and chelating dyes. This reaction is based on the increase in absorbance of the complex formed among molybdenum, bromopyrogallol red and increasing concentrations of cationic surfactants. Under optimum conditions, two calibration plots were obtained for a concentration range between 2.50 x 10(-7) mol dm(-3) (detection limit) and 5.00 x 10(-4) mol dm(-3) of cetylpyridinium chloride, used as standard. Solubilization of water insoluble complexes formed for concentrations of cationic surfactants greater than 1.00 x 10(-4) mol dm(-3) were successfully achieved with Triton X-405. RSD values lower than 5.0% were obtained in all cases. The quality of the results obtained for 18 water samples were evaluated by comparison with conventional methods, with no statistically significant differences for a 95% confidence level.     

A kinetic method for the determination of copper(II) by its catalytic effect on the oxidation of 3-methyl-2-benzothiazolinone hydrazone with hydrogen peroxide: a mechanistic study.

A catalytic spectrophotometric method for the determination of traces of copper(II) is proposed. 3-Methyl-2-benzothiazolinone hydrazone (MBTH) is oxidized by hydrogen peroxide to form a yellowish-brown compound. The reaction is accelerated by trace amounts of copper(II), and can be followed by measuring the increase in the absorbance at 390 nm. Since the absorbance at 40 min from the reaction start increases with an increase in the copper(II) concentration, the absorbance value is used as a parameter for copper(II) determination. Under the optimum experimental conditions (8.4 x 10(-3) mol dm(-3) MBTH, 0.7 mol dm(-3) hydrogen peroxide, pH 5.2, 35 degrees C), copper(II) can be determined in the range 0-50 microg dm(-3). The relative standard deviations are 6.9, 3.5, 2.7% for 2, 20 and 40 microg dm(-3), respectively. The detection limit of this method (3sigma) is 0.27 microg dm(-3). It was successfully applied to a determination of copper(II) in river water, tap water and ground-water samples. According to the results of a kinetic study, a mechanism is proposed which leads to the following rate equation: R0(cat) = kK1K2[MBTH][H2O2][Cu(II)]0/{(1 + K2[H2O2])[H+]}.     

Simultaneous determination of calcium and magnesium by derivative spectrophotometry in pharmaceutical products

First- and second-derivative spectrophotometric methods for the simultaneous determination of calcium and magnesium in their mixtures are described. The methods are based on the colored complexes formed by calcium and magnesium with bromopyrogallol red in presence of Tween 80 as a surfactant. The zero-crossing method has been utilized to measure the first- and second-derivative value of the derivative spectrum. Calcium (0.8-4.8microgml(-1)) is determined in the presence of magnesium (0.5-3.5microgml(-1)) at the pH 10 and vice versa at zero-crossing wavelengths of 544.5 and 570nm in the first-derivative procedure and 574 and 531nm in the second-derivative procedure, respectively. The detection limits achieved were 0.0575microgml(-1) of calcium and 0.03microgml(-1) of magnesium. The relative standard deviations were in all instances less than 2%. The proposed method has been applied to the simultaneous determination of calcium and magnesium in different samples: commercial multivitamin, human serum and drinking water where excellent agreement between reported and obtained results was achieved.     

Determination of cobalt and nickel by graphite-furnace atomic absorption spectrometry after coprecipitation with scandium hydroxide.

Trace amounts of cobalt and nickel in a water sample were quantitatively coprecipitated with scandium hydroxide at pH 8.0-10.5. Because the coprecipitant could be easily dissolved with 1 mol dm(-3) nitric acid, and the presence of up to 10 mg cm(-1) of scandium did not interfere with the graphite-furnace atomic absorption spectrometric determination of cobalt and nickel, the volume of the final solution prepared for the determination could be minimized down to 0.5 cm3. The concentration factor was 400-fold and the detection limits (signal to noise = 2) were 5.0 pg cm(-3) of cobalt and 10.0 pg cm(-3) of nickel in 200 cm3 of the initial sample solution. The 27 diverse ions investigated did not interfere with the determination in at least a 500-fold mass ratio to cobalt or nickel. The proposed method was successfully applied to the determination of trace amounts of cobalt and nickel in river-water samples.     

Spectrophotometric determination of Cu(II) with sequential injection analysis

A sequential injection system, based on the reaction of Cu(II) with diethyldithiocarbamate (DDTC), was developed for the determination of Cu(II) in plant food and water samples. The extraction procedure, generally used to extract the Cu(II)–DDTC complex for subsequent analysis was eliminated in this procedure. The complex was detected spectrophotometrically in aqueous solutions at 460 nm. The physical and chemical parameters depicting the system were studied to obtain optimum conditions for sample analysis. The system developed is fully computerized and able to monitor Cu(II) in samples at seven samples per hour with a relative standard deviation of <4.50%. The calibration curve is linear from 0.5–5.0 mg/l with a detection limit of 0.2 mg/l. Interferences were reduced by introducing multiple flow reversals, to increase mixing between the reagent and sample zones, and subsequently enhance working of the masking agents (EDTA/citrate).     

Spectrophotometric determination of sulfide in the presence of sulfite and thiosulfate via the precipitation of bismuth(III) sulfide.

A photometric method has been developed for the determination of sulfide at 10(-5) mol dm(-3) levels, which is based on the reaction of sulfide with a given excess amount of bismuth(III) to form a precipitate of bismuth(III) sulfide and on the spectrophotometric measurement of the residual bismuth(III) at 335 nm after extracting with bismuthiol II reagent from an aqueous solution containing acetate buffer into benzene. The presence of sulfite and thiosulfate up to 0.002 mol dm(-3) did not cause any interference in the determination of sulfide, because both sulfite and thiosulfate do not produce any precipitate with bismuth(III). A linear calibration plot with a negative slope was obtained for sulfide over the range of 5.00 x 10(-7) - 3.00 x 10(-5) mol dm(-3) (16.0 - 960 ppb). An experimental calibration plot was in accord with the theoretical plot, taking into account the known excess of bismuth(III), showing that the reaction of sulfide with bismuth(III) proceeded to completion. The relative standard deviation of results from 10 replicate determinations of standard sulfide (2.00 x 10(-5) mol dm(-3)) was 0.44%. The proposed method was successfully applied to the determination of sulfide in hotspring water samples without any pretreatment.     

Simultaneous spectrophotometric determination of uranium and thorium by flow injection analysis using selective masking.

A flow injection system for the simultaneous determination of uranium and thorium has been developed by using selective masking and a spectrophotometric detector with two flow cells aligned with the same optical path. The injected sample solution was first mixed with a reagent solution containing Chromazurol S (CAS) and cetyltrimethylammonium chloride (CTMAC), and the total absorbance of uranium- and thorium-CAS complexes was measured in the first flow cell at 620 nm. The sample stream was then mixed with an EDTA solution in order to convert the thorium-CAS complex to a thorium-EDTA complex, and the absorbance of the uranium-CAS complex was measured in the second flow cell. The detection limits were 10 microg dm(-3) for uranium and 7 microg dm(-3) for thorium. The calibration graphs were linear (r < 0.9998) at least over the ranges of 0.1 to 10 mg dm(-3) for uranium and 0.08 to 8 mg dm(-3) for thorium. The RSDs were less than 1.5% (n = 3) in the calibration range. Uranium and thorium of up to the 6-fold concentration to each other could be determined in admixtures with relative errors of less than 3.3%. The sample throughput was 24 per hour. The proposed system was successfully applied to the analysis of a uranium-thorium ore mock solution by coupling with anion-exchange in a magnesium nitrate medium to eliminate interference from coexisting elements.     

Solid-phase reactors in sequential injection analysis. Determination of manganese (II) in tap water and effluent streams using a solid-phase lead(IV) dioxide reactor in a sequential injection system

The determination of manganese(II) in tap water and effluent streams, using a solid-phase reactor incorporated into a sequential injection system was investigated. Mn2+-ions in samples injected into a carrier stream, were oxidised by solid lead(IV) dioxide suspended on silica gel beads to form MnO4- -ions which were detected spectrophotometrically at 526 nm. The linear range of the system is from 1 to 7 mg L(-1) with a detection limit of 0.62 mg L(-1). The proposed system is suitable for the determination of manganese(II) in tap and effluent streams at a rate of approximately 50 samples per hour with a relative standard deviation of better than 3%. Statistical comparison between the proposed sequential injection system and a standard ICP method revealed that there is no significant difference between the two methods at the 95% confidence level for effluent streams and at 99.9% for tap water.     

Determination of residual chlorine in greywater using o-tolidine

The determination of chlorine with o-tolidine in greywater has been studied, and a batch method and a sequential injection method have been proposed. It was found that the reaction of o-tolidine with chlorine was slower in a greywater matrix. Grey water samples must be filtered before analysis, or alternatively, a blank of sample must be measured. The samples are very unstable, and after 2 h of storage in dark conditions at 4 degrees C the chlorine concentration can diminish. The standard addition method, in some samples gave unsatisfactory results as a consequence of matrix effects. It was concluded that samples with a total organic carbon (TOC) higher than 60 mgCl(-1) can not be accurately analysed using these methods. However, samples with a TOC lower than 60 mgCl(-1) gave 100+/-3% recoveries. The linear range of the methods was 0-3.0 and 0-5.0 mgCl(2)l(-1), and the limit of quantification 0.2 and 0.5 mgCl(2)l(-1), for the batch method and the sequential injection method, respectively. This is the first paper devoted to grey water from the analytical chemistry point of view.     

Simultaneous determination of trace amounts of cadmium, nickel and cobalt in water samples by adsorptive voltammetry using ammonium 2-amino-cyclopentene dithiocarboxylate as a chelating agent

This paper reports the use of an adsorptive voltammetric technique for the simultaneous detection of Cd(II), Ni(II) and Co(II) using ammonium 2-amino-cyclopente dithiocarboxylate as a selective complexing agent. Scans containing three resolved peaks corresponding to these metals were obtained in synthetic and real samples. The reduction current peaks of the metals that were distinctly separated by 200 mV or more, allowing their determination over a wide range of concentrations. These metals can be quantified at concentrations above 1.33x10(-8) mol dm(-3) Cd(II), 8.51x10(-9) mol dm(-3) Ni(II) and 3.39x10(-10) mol dm(-3) Co(II). The influence of pH, ligand concentration, scan rate, accumulations time and applied potential was investigated. The R.S.D. at a concentration level of 1.78x10(-7) mol dm(-3) of Cd(II), 3.40x10(-7) mol dm(-3) and Ni(II) and 1.7x10(-9) mol dm(-3) of Co(II) was 2.5% for Cd(II), 2.7% for Ni(II) and 3.3% for Co(II). The method was applied to various water samples.     

Direct determination of calcium,copper, iron,magnesium, manganese and zinc in amniotic fluid samples using inductively coupled plasma-atomic emission spectrometry

An inductively coupled plasma-atomic emission spectrometric method is reported for the determination of calcium, copper, iron, manganese, magnesium and zinc. Samples are introduced directly when a sheath gas device is used. An external calibration procedure is used. The standards are prepared in a matrix composed of 0.5% (w/v) albumin and 0.76% (w/v) sodium chloride. The procedure was evaluated with a standard reference material (NBS SRM 909 Human Serum); all the values obtained are in agreement with the certified values. Results obtained for the determination of zinc, calcium, magnesium, copper, iron and manganese in amniotic fluid samples are reported.     

Nitrite reduction and detection at a carbon paste electrode containing hemoglobin and colloidal gold

A novel renewable reagentless nitrite biosensor based on the direct electron transfer of hemoglobin (Hb) and a new sensing mechanism was proposed by combining the advantageous features of colloidal gold nanoparticle and carbon paste technology. The direct electrochemistry of immobilized Hb displayed a pair of redox peaks with a formal potential of -42 mV (vs. NHE) in 0.2 mol dm(-3) NaAc-HAc buffer (pH 5.5). The immobilized Hb displayed an excellent response to the reduction of NO2(-) with one interfacial charge transfer followed by a chemical reaction (EC) mechanism. Under optimal conditions, the interfacial EC process could be used for the sensitive determination of NO2(-) with a linear range from 0.1 to 9.7 micromol dm(-3) and a detection limit of 0.06 [micro sign]mol dm(-3) at 3sigma. The amperometric determination of high concentrations of NO2(-) based on the irreversible reduction of NO could be performed at pH 4.0 with a linear range from 0.1 to 1.2 mmol dm(-3). The surface of biosensor could be renewed quickly and reproducibly by a simple polish step. The biosensor has been used satisfactorily for nitrite determination in native water samples.     

Minimization of lead and copper interferences on spectrophotometric determination of cadmium using electrolytic deposition and ion-exchange in multi-commutation flow system

A new strategy for minimization of Cu(2+) and Pb(2+) interferences on the spectrophotometric determination of Cd(2+) by the Malachite green (MG)-iodide reaction using electrolytic deposition of interfering species and solid phase extraction of Cd(2+) in flow system is proposed. The electrolytic cell comprises two coiled Pt electrodes concentrically assembled. When the sample solution is electrolyzed in a mixed solution containing 5% (v/v) HNO(3), 0.1% (v/v) H(2)SO(4) and 0.5 M NaCl, Cu(2+) is deposited as Cu on the cathode, Pb(2+) is deposited as PbO(2) on the anode while Cd(2+) is kept in solution. After electrolysis, the remaining solution passes through an AG1-X8 resin (chloride form) packed minicolumn in which Cd(2+) is extracted as CdCl(4)(2-). Electrolyte compositions, flow rates, timing, applied current, and electrolysis time was investigated. With 60 s electrolysis time, 0.25 A applied current, Pb(2+) and Cu(2+) levels up to 50 and 250 mg l(-1), respectively, can be tolerated without interference. For 90 s resin loading time, a linear relationship between absorbance and analyte concentration in the 5.00-50.0 mug Cd l(-1) range (r(2)=0.9996) is obtained. A throughput of 20 samples per h is achieved, corresponding to about 0.7 mg MG and 500 mg KI and 5 ml sample consumed per determination. The detection limit is 0.23 mug Cd l(-1). The accuracy was checked for cadmium determination in standard reference materials, vegetables and tap water. Results were in agreement with certified values of standard reference materials and with those obtained by graphite furnace atomic absorption spectrometry at 95% confidence level. The R.S.D. for plant digests and water containing 13.0 mug Cd l(-1) was 3.85% (n=12). The recoveries of analyte spikes added to the water and vegetable samples ranged from 94 to 104%.